SoundOff Signal nFORCE Oval Recess Mount User Manual
nFORCE 6” Oval Recess Mount Light, SAE Class 1
ENFSLSRV(x)(yyy) - Custom Ordered Through Configurator
ENFSRV1(x) - 6 LED
ENFSRV2(x) - 9 LED
ENFSRV3(x) - 12 LED
LIGHT ASSEMBLY
GASKET
TECHNICAL SPECIFICATIONS
6” OVAL RECESS MOUNT nFORCE
Dimensions: 7.75”L x 3.25”H x 1.65”D
Input Voltage: 10 - 16 Vdc or 10 - 30 Vdc *
CURRENT CONSUMPTION PER MODULE
10-16 Vdc 10-30 Vdc *
6, 12 Split &
18 Tri-Color
9 LED Single Color <1.5A @ 12.8 Vdc <0.9A @ 25.6 Vdc
12 LED Single Color <2.0A @12.8 Vdc <1.2A @ 25.6 Vdc
1.
<1.0A @12.8 Vdc <0.6A @25.6 Vdc
* - Special Order
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. Eastern Time or during extended after hours coverage between 5 p.m. & 8 p.m. Eastern
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
INSTALLATION:
1) Establish a position on the vehicle. Use the
cutout template (provided) on 2nd page and cut
hole. Insert grommet into cutout first and then
press the light assemble into the grommet.
nFORCE SECONDARY INFORMATION:
WIRE HOOK-UP TABLE
WIRE
COLOR:
BLACK
**GREEN
WHITE 1
** To sync multiple nFORCE lights,
connect the Green wires from each light
together. *Individual light applications connect
the Green & Blue wires together.
* Will NOT work w/ other sync products such as
Ghost, LED3, & Intercector.
RED
LIGHT
HEAD
1
1
1
FUNCTION:
Power
Ground
Sync2 *
To Ground: Pattern
Select/ Setup
To Power: Secondary
Fuction
-see page 2-
Connecting the WHITE or Yellow (Dual) wire to
power will allow you to use the secondary function
on your Nexus Secondary Light.
SECONDARY FUNCTION:
• 1-color module = Cruise Mode (10% brightness,
non-flashing)
• 2 - color modules = Separate Color Control (see
Setup Table) or Takedown (100% steady-burn of
the 2nd color)
• 3 - color modules = Takedown (100% steady burn of the 3rd color)
SETUP LIGHTS:
Simultaneous or Alternate Function
•1 or 2. The modules will flash simultaneously if
they are set to the same number. The modules will
have an alternate flash if set to different numbers.
Color swap
• Off or On. 2-color and 3-color modules, it changes
which color flashes first.
Separate color control(2 color lights only)
•Allows manual switching of flashing color. When
this feature is programmed in the On state: the
light will jump to the first pattern of the 1-color
patterns, you will only be able to choose 1-color
patterns, and Color Swap will be programmed to
Off. To select a 2-color pattern, program this
feature to the Off state. *To turn off
PATTERN SELECT & SYNC
CONFIGURATION INSTRUCTIONS
Seperate Color Control you must do a
factory reset.
Sync
Pattern/Function
+Vdc
A FUSE
5
IMPORTANT INFORMATION:
Time at 1.800338.7337 (press #4 to skip the automated message).
Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsigal.com.
GREEN
WHITE
RED
BLACK
ENFSRV(xx) 10.14
SLAVE MODE
The nFORCE is capable of being activated through the use of a user supplied flasher by putting it in Slave Mode.
1. Permanently connect the nFORCE WHITE and BLACK wire (or WHITE/BLACK and YELLOW wire for second
module of Dual Light) to a good, convenient ground.
2. Connect the nFORCE RED wire, *(Dual use RED & ORANGE wire) through a 5amp fuse, to the output of a
+10-16Vdc switching flasher.
6.75
AFTER POWER IS ON, touching the WHITE or Yellow (Dual)
wire to the ground will allow you to change various setting on
the module. (See table below)
SECONDS USER INTERFACE
FROM TO VISUAL FEEDBACK ACTION TAKEN
0 1 STEADY-HIGH (60%) FORWARD ONE PATTERN
1 2 STEADY-LOW (30%) BACKWARD ONE PATTERN
2 3 OFF COLOR SWAP (OFF OR ON )
3 4 STEADY - HIGH (60%) SIMULTANEOUS OR ALTERNATE
4 5 STEADY - LOW (30%)
*
5 6 OFF RESET TO PATTERN 1
6 7 STEADY-HIGH (60%)
If held longer than 7 seconds, the light will go back to flashing the current
pattern and no action will be taken.
SEPARATE COLOR CONTROL
(OFF OR ON)
FACTORY RESET (PATTERN 1, COLOR
SWAP: OFF, SEQUENCE TYPE:1)
SEPARATE COLOR CONTROL: OFF
1.25” Radius x2
2.
IMPORTANT NOTE:
Due to variations in the printing process and environmental factors, the sizes
shown may not be accurate. If this document is used as a cutting template,
it is the installer’s responsibility to confirm the accuracy of the dimensions
shown and adjust accordingly.
6” OVAL CUTOUT TEMPLATE
2.50
ENFSRV(xx) 10.14
Loading...