SoundOff Signal nFORCE Deck Grille User Manual
SAE CLASS 1 DECK/ GRILL MOUNTS
SINGLE MOUNT VERSION
LIGHT ASSEMBLY
DOUBLE MOUNT VERSION
BRACKET
TECHNICAL SPECIFICATIONS
DECK/ GRILL MOUNT NEXUS
Single Mount
Dimensions:
Double Mount
Dimensions:
Input Voltage: 10 - 16 Vdc or 10 - 30 Vdc *
CURRENT CONSUMPTION
6, 12 Split &
18 Tri-Color
<1.0A @12.8 Vdc <0.6A @25.6 Vdc
9 LED Single Color <1.5A @ 12.8 Vdc <0.9A @ 25.6 Vdc
12 LED Single Color <2.0A @12.8 Vdc <1.2A @ 25.6 Vdc
5.0”L x 1.88”H x 1.82”D
9.50”L x 1.88”H x 1.82”D
10-16 Vdc 10-30 Vdc *
* - Special Order
INSTALLATION:
1) Establish a at position on the vehicle.
Drill 3/16” holes in the center of
the mounting locations. Note: 2 bolts
are desired for the single mount and 4
bolts for the double mount attachments
(not included with hardware kit). See
page 2 for hole spacing.
INFORMATION FOR NEXUS
SECONDARY:
WIRE HOOK-UP TABLE
WIRE COLOR: FUNCTION:
RED Power
BLACK Ground
GREEN Sync2 *
WHITE Pattern Select
Please see reverse for
Technical Specifications
Important Information:
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website at www.soundoffsignal.com and select the “Warranty & Returns”
link along the left column of our home page. If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at 1.800.338.7337, press #4 to
skip the automated message. Questions or comments that do not require immediate attention may be emailed to techsupport@soundoffsignal.com.
1.800.338.7337. / www.soundoffsignal.com / Thank you for trusting us with your safety!
* Will NOT work w/ other sync
products such as Ghost, LED3,
& Intercector.
ENFSLXGS 7.12
1.20"
3.43"
4.63"
SLAVE MODE
The NFORCE™ is capable of being activated through the use of a user
supplied flasher by putting it in Slave Mode.
1. Permanently connect the NFORCE™ WHITE and BLACK wire to a good,
convenient ground.
2. Connect the NFORCE™ RED wire, through a 5amp fuse, to the output of
a +10-16Vdc switching flasher.
0.22"
HOLE 4x
PATTERN SELECT & SYNC
CONFIGURATION INSTRUCTIONS
Connecting the WHITE wire to power will
allow you to use the secondary feature on
your Nexus Secondary Light.
SECONDARY FEATURE:
• 1-color module = Cruise Mode
(10% brightness, non - ashing)
• 2 & 3 - color modules = Takedown
(100% Steady - burn)
- For 2-color modules this is the 2nd color
- For 3-color modules, this is the 3rd color
SETUP LIGHTS:
• Sequence type
-1 or 2. The modules will ash simultaneously if they are set to the same number.
The modules will have an alternate ash if
set to different numbers.
“ “
“
0.20
HOLE 2X
DOUBLE MOUNT DECK/ GRILLE TEMPLATE
2.36 1.31
SINGLE MOUNT DECK/ GRILLE TEMPLATE
• Color swap
- Off or On. 2-color and 3-color modules, it
changes which color ashes rst.
This is useful when syncing multiple lights
Touching the WHITE wire to the ground will allow
you to change various setting on the module.
SECONDS USER INTERFACE
FROM TO VISUAL FEEDBACK ACTION TAKEN
0 1 STEADY-HIGH (60%) FORWARD ONE PATTERN
1 2 STEADY-LOW (30%) BACKWARD ONE PATTERN
2 3 OFF COLOR SWAP (OFF OR ON )
3 4 STEADY - HIGH SEQUENCE TYPE (1 OR 2)
4 5 STEADY - LOW RESET TO PATTERN 1
5 6 OFF
If held longer than 6 seconds, the light will go back to flashing the current
pattern and no action will be taken.
FACTORY RESET (PATTERN 1, COLOR
SWAP: OFF, SEQUENCE TYPE: 1)
ENFSLXGS 7.12