SoundOff Signal GHOST Recess Mount ECE User Manual

GHOST® SINGLE RECESS MOUNT LIGHT
ECE CERTIFIED

SINGLE LIGHT
EGHSTE5(x)B - Black
EGHSTE5(x)W - White
EGHSTE5(x)C - Chrome

GHOST® SINGLE RECESS MOUNT LIGHT
XYLEX LENS - ECE CERTIFIED

SINGLE LIGHT
EGHSTE5(x)B-EU - Black
EGHSTE5(x)W-EU - White
EGHSTE5(x)C-EU - Chrome

Please see reverse for
Technical Specifications

Important Information:

• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.

• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.

• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.

GASKET

Note: Lens shown is
representative only.

LIGHT ASSEMBLY

WARNING

!

This product contains high intensity LED devices. To

prevent eye damage, DO NOT stare into the light

beam at close range.

INSTALLATION:

1. Determine a clean, flat location on the
vehicle to mount the GHOST light.

2. Using template on reverse side, mark and
drill holes in 4 corners. Holes to be Ø0.46”
(approx. Ø15/32”).

3. Carefully cut sheet metal and ensure there
are no sharp edges.

4. Press gasket into opening.

5. Make electrical connections.

6. Test light.

7. Press light into gasket.

OPERATION:

WIRE CONNECTIONS

See setup procedure on second page.

The single GHOST comes equipped with
an internal flasher with 3 user selectable
patterns that can be synchronized either
alternating or simultaneous with up to three
other lights. It can also be put into slave
mode and driven through an external flasher.

1. Connect the GHOST BLACK wire to a

good, convenient ground.

2. Connect the GHOST RED wire to one side

of a user supplied on/off switch. Connect the
other side of the switch, through a 5Amp
fuse, to a source of +10-30Vdc.

3. Cruise mode is activated by applying

power to BROWN wire while RED wire is
powered. NOTE: Cruise mode is STEADY-ON
at 20% light output.

4. To sync lights and make pattern

selections see reverse side.

WIRE HOOK-UP TABLE

WIRE COLOR: CONNECT TO:

RED +10-30Vdc

BLACK Ground (-)

WHITE ID/Pattern Select

BROWN WIRE +10-30Vdc

Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.

1.800.338.7337 / www.soundoffsignal.com

IMPORTANT INFORMATION:

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.

If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800.338.7337 (press #4 to skip the automated message).

Questions or comments that do not require immediate attention may be emailed to [e-mail].

SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.

EGHSTE5(xx) 07.14

RECESS MOUNT ECE65 CERTIFIED
w/ STANDARD LENS

SINGLE LIGHT
EGHSTE5(x)B - Black
EGHSTE5(x)W - White
EGHSTE5(x)C - Chrome

RECESS MOUNT ECE65 CERTIFIED
w/ XYLEX LENS

SINGLE LIGHT
EGHSTE5(x)B-EU - Black
EGHSTE5(x)W-EU - White
EGHSTE5(x)C-EU - Chrome

1 Cut hole in sheet metal

2 Press gasket into hole

ONE (1) LIGHT

Single Light Operation: Follow the ID Selection steps and set the ECE
GHOST to ID#1 if it is not already.

TWO (2) LIGHTS

ALTERNATING: To obtain Alternating patterns, follow the ID

SELECTION steps and set one ECE GHOST to ID#1 and the other to
ID#3. Then proceed to the PATTERN SELECTION steps.

SIMULTANEOUS: To obtain Simultaneous patterns, follow the ID
SELECTION steps and set both ECE GHOST lights to ID#1. Then
proceed to PATTERN SELECTION steps.

SLAVE MODE

The GHOST is capable of being activated through the use of a use sup
plied flasher by putting it in slave mode.

1. Permanently connect the GHOST WHITE and BLACK wire to a good,
convenient ground.

2. Connect the GHOST RED wire, through a 5Amp fuse, to the output of a
+10-30 Vdc switching flasher.

PATTERN RESET

1. Remove power

2. Place WHITE (sync) wire to ground

3. With sync wire grounded, re-power RED wire

4. Maintain for one second (light will dim)

5. Remove power and ground (pattern 1 set)

-

TECHNICAL SPECIFICATIONS

Overall Dimensions: 1.55” H x 4.67” W x 0.98” D

Input Voltage Range: 10 - 30 Vdc

Current Consumption:

0.75 Amps max / module
(flash pattern dependent)

# of LEDs: 6 Generation 3 LEDs

Light Sync Technology: Yes

Operating Temperature: -40º to +65º C

Cruise Light Mode:

Yes

ECE GHOST Sync Configuration Instructions

IMPORTANT! A MAXIMUM OF 4 SINGLE LIGHTS
CAN BE SYNCED TOGETHER

1. Set ID#
a. Identify which pattern and sequence you want and look up ID#

settings at right.

b. Connections
i. RED: +12Vdc
ii. WHT: +12Vdc (Note: you will need to disconnect after
power is applied)
iii. BLK: Ground
c. Apply power to unit
d. Without disconnecting power from unit, disconnect WHT
wire
e. Momentarily connect WHT to Ground to change ID #
i. Identify ID# by number of sequential flashes
ii. Possible ID#s: 1 – 4
f. Disconnect power from unit to get out of ID mode.

2. Set Pattern
a. Reapply power to units.
b. Once all Light Head ID#s are configured, make sure all
lights are flashing the same pattern
c. Connect corresponding colored wires of all units together:
RED to RED, etc.
d. Change Pattern
i. Momentarily touch WHT wires to Ground
ii. Observe pattern change on all lights connected
e. Insulate all wires by taping with electrical tape

3. Connect Master Switch for Application
a. IMPORTANT! Ensure WHT Pattern/Sync Wires are tied
together

Flash Patterns

Pattern Name

1. Single 125

2. Double 125

3. Triple 123

FPM

(Flashes per Minute)

3 Make wiring connections

4 Test

5 Install light

NOTE:

The GHOST is a factory sealed unit that CANNOT be serviced
in the field. Any attempt to gain access to the GHOST unit will
most likely cause permanent damage and void its warranty.

1.800.338.7337 / www.soundoffsignal.com

4.28

3.81

R0.23

0.72

1.19

EGHSTE5(xx) 07.14