SoundOff Signal GHOST Multi Mount User Manual

INSTALLATION:

OPERATION:

GHOST® DUAL MULTI-MOUNT LIGHT

EGHST1(x)-12 - Black EGHST1(x)W-12 - White

Supplied #10 thread forming screw.

Hole with #27 drill

Screw Mount Adhesive Mount ‘U’ bracket

Important Information:

• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.

• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle Owner’s Manual for the location of any air bag deployment zones.

• DO NOT connect this device to a strobe power supply. This product is self-contained and does not require an external power supply.

Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.

If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800.338.7337 (press #4 to skip the automated message).

1.800.338.7337 / www.soundoffsignal.com

SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.

Supplied #10-24 3/8” lg. hex drive set screw

Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsigal.com.

1. Screw Mount Establish a position on the vehicle. Use

the mounting slots as a template to mark hole locations. Drill a hole using a #27 drill bit. The Torx screws provided are selftapping.

Loosen the two #10 TORX screws on

the back of each housing to adjust the angle of the GHOST. After adjustment, tighten the

TORX screws.

2. Adhesive Mount To obtain optimum adhesion, the bonding

surfaces must be well uniﬁed, clean and dry. Peel one side of each adhesive mounting patch provided. Apply each rectangular patch to the bottom of the GHOST housing. Positon the GHOST on the vehicle and mark

2 edges of the location using tape. Peel the

remaining paper from the adhesive patch and carefully position the light using the tape template. Press down on housing ﬁrmly to insure good adhesive contact. Important:

Apply carefully; adjustment is not possible

after the adhesive bonds. Ultimate strength of adhesive is achieved after 24 hours.

Loosen the two #10 TORX screws on

the back of each housing to adjust the angle of the GHOST. After adjustment, tighten the

TORX screws.

3. New ‘U’ bracket for mounting on hood or trunk edge.

Open the hood or trunk that will be the

attachment surface. Place the rubber pad provided on the surface, insuring that the lower lip is on the edge of the sheet metal. Fit the ‘U’ bracket to the back of the GHOST light base, nesting the bracket holes with the pins on thelight base. Slide the assembly onto the rubber pad. Tighten the four set screws.

Loosen the two #10 TORX screws on

the back of each housing to adjust the angle of the GHOST. After adjustment, tighten the

TORX screws.

IMPORTANT INFORMATION:

WIRE CONNECTIONS

See setup procedure on second page.

The single GHOST comes equipped with an internal ﬂasher with 33 user selectable patterns that can be synchronized either alternating or simultaneous with up to three other lights. It can also be put into slave mode and driven through an external ﬂasher.

1. Connect the GHOST BLACK wire to a good, convenient ground.

2. Connect the GHOST RED wire to one side of a user supplied on/off switch. Connect the other side of the switch, through a 5Amp fuse, to a source of +10-16Vdc.

NOTE:

The GHOST is a factory sealed unit that CANNOT be serviced in the ﬁeld. Any attempt to gain access to the GHOST unit will most likely cause permanent damage and void its warranty.

TECHNICAL SPECIFICATIONS

Overall Dimensions: 4”L x 0.88”H x

Input Voltage Range: 10-16Vdc

Current Consumption: 0.75 Amps /module*

Light Sync Technology Yes

Operating Temperature: -20º to +65º C

# of Flash Patterns 33

*Pattern Dependent

WARNING

This product contains high

intensity LED devices. To prevent

eye damage, DO NOT stare into

light beam at close range.

1.75”D

EGHST1(xx)-12 7.14

GHOST® DUAL MULTI-MOUNT LIGHT

EGHST1(x)-12 - Black EGHST1(x)W-12 - White

1 SINGLE LIGHT

Follow the ID selection steps and set the GHOST to the following ID:

- Alternating (default): ID#1 or ID#3. (inludes cycle patterns and steady burn patterns)

- Simultaneous: ID#2 or ID#4. (both lights will ﬂash together regardless of pattern)

2 SINGLE LIGHTS

Follow the ID selection steps and set the GHOST to the following ID: ***IMPORTANT: Make sure both lights ﬂash the same pattern!***

- Both assemblies simultaneous with individual lights alternating.

- Example: Driver/Passenger sim; Dr.(left alt right)

Pass.(left alt right)

- Set both GHOST Assemblies to ID#1

- Both assys. alternating with individual lights alternating.

- EX: Dr./Pass. alt; Dr.(left. alt. right.) Pass.(right alt. left)

- Set one GHOST to ID#1 and the other to ID#3

- Both assys. alternating with individual lights simultaneous

- EX: Dr./Pass. alt; Dr.(left sim left) Pass.(right sim right)

- Set one GHOST to ID#2 and the other to ID#4

- Both assys. simultaneous with individual lights simultaneous.

- EX: Dr./Dr. sim; Dr.(left sim left) Pass.(right sim right)

- Set both Ghost housings to ID#2

X-PATTERN - To obtain X-Patterns, follow the ID SELECTION steps and set

one of the four GHOST lights to ID#1, one to ID#2, one to ID#3, and one to ID#4. Then proceed to the PATTERN SELECTION steps.

NOTE: Be sure to mount each GHOST in the correct placement based on ID#.

PATTERN SELECTION

1. Disconnect WHITE wire from any connections if applicable.

2. Turn GHOST ON.

3. Momentarily touching and removing the WHITE wire(s) to ground will advance the GHOST to the next ﬂash pattern. Touching and removing

the White wire for more than a few seconds will allow you to change the GHOST to the previous pattern. See ﬂash pattern table. Continuing to touch and remove the WHITE wire(s) to ground will allow you to scroll through the pattern list. After pattern #33 is reached the list will start over again at pattern #1.

X-Pattern Sequence

ID#1> ID#4> ID#2> ID#3

X-Pattern Light Head Placement

ID#4 ID#2 ID#3 ID#1

NOTE: The GHOST is equipped with ﬂash pattern memory. Once you have selected a pattern the GHOST will always activate to that pattern every time the unit is turned on. Tape up and secure WHITE wire so that it will not ac

cidentally change your selected pattern.

Ghost Sync Conﬁguration Instructions IMPORTANT! A MAXIMUM OF 4 SINGLE LIGHTS CAN BE SYNCED TOGETHER

1. Set ID# a. Identify which pattern and sequence you want and look up ID# settings at left. b. Connections i. RED: +10-16Vdc ii. WHT: +10-16Vdc (Note: you will need to disconnect after power is applied) iii. BLK: Ground c. Apply power to unit d. Without disconnecting power from unit, disconnect WHT wire e. Momentarily connect WHT to Ground to change ID # i. Identify ID# by number of sequential ﬂashes ii. Possible ID#s: 1 – 4 f. Disconnect power from unit to get out of ID mode.

2. Set Pattern a. Reapply power to units. b. Once all Light Head ID#s are conﬁgured, make sure all lights are ﬂashing the same pattern. c. Connect corresponding colored wires of all units together: RED to RED, etc. d. Change Pattern i. Momentarily connect WHT wires to Ground ii. Observe pattern change on all lights connected e. Insulate all wires by taping with electrical tape

3. Connect Master Switch for Application a. IMPORTANT! Ensure WHT Pattern/Sync Wires are tied together.

PATTERN RESET

1. Remove power

2. Place WHITE (sync) wire to ground

3. With sync wire grounded, re-power RED wire

4. Maintain for one second (light will dim)

5. Remove power and ground (pattern 1 set)

SLAVE MODE

The GHOST is capable of being activated through the use of a user

supplied ﬂasher by putting it in slave mode.

1. Permanently connect the GHOST WHITE and BLACK wire to a good, convenient ground.

2. Connect the GHOST RED wire, through a 5Amp fuse, to the output of a +10-16Vdc switching ﬂasher.

Flash Patterns

Pattern Name 1 Light

1. Quint

2. Warp

3. Inter-Cycle Flash

4. Double Flash

5. Quad Flash

6. PowerPulse

7. RoadRunner

8. Q-Switch

9. RoadRunner Steady Burn

10. Quad Steady Burn

11. E-Ideal Single Flash

12. E-Ideal Double Flash

13. Quad2 Flash

14. Double2 Flash

15. X-Warp

16. X-Double

17. PowerRunner

18. LCR Quint

19. Warp

20. Ultra Warp

21. Thunder & Lightning

22. Lite Speed

23. SuperSonic

24. LCR Lite Speed

25. SuperSonic Ultra

26. Tempo Shift

27. Tempo Shift Warp

28. SBE2

29. C

30. U

31. Ultra Glow

32. Cyclone

33. Chameleon

x x x 70

x x x 350

x x

x x x 70

x x x 80

x x x 180

x x x 113

x x

x x 113

x x 80

x x x 200

x x x 146

x x x 67

x x x 95

x x x

x x x 545

x x

x x x 85

x x 170

x x x

x x x 67

x x x 200

x x x 176

x x x

Alternating 2

Lights

Silmultaneous

2 Lights

X-Pattern

4 Lights

F.P.M.

(Flashes / Minute)

1.800.338.7337 / www.soundoffsignal.com

EGHST1(xx)-12 7.14

SoundOff Signal GHOST Multi Mount User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual