FUSION LED LIGHT
#EFL1(x)Ø(x)
#EFL2(x)0(x)
INSTALLATION:
1. Establish a position on the vehicle on a level
surface. Orient the light output level on the
horizon.
2. Use the screw holes in the assembly as
a template to mark locations of wire and
mounting screws.
3. Use a 5/16” diameter drill for the wire holes
4. Size pilot holes for mounting screws
appropriately.
5. Fasten light using mounting
screws. Do not torque mounting screws
beyond 20 in - lbs.
FIGURE 1
Please see last page for
Technical Specifications
FIGURE 2
Important Information:
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.
1.800.338.7337 / www.soundoffsignal.com
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the automated message).
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsigal.com.
IMPORTANT INFORMATION:
WIRE HOOK-UP TABLE
WIRE COLOR: CONNECT TO:
RED +Vdc
BLACK Ground (-)
WHITE
Pattern Select/Sync
GREEN Group Flash
WARNING
!
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
EFL1B0(x)_EFL1W0(x) 8.14
Pg. 1
FUSION LED LIGHT
#EFL1(x)Ø(x)
#EFL2(x)0(x)
Tech Specs Fusion Lite
Flash Patterns:
Light Sync:
Technology:
Mounting:
Input Voltage:
Current Draw:
Dimensions:
Operating Temp.:
Pattern Name
1. Warp
2. Power Pulse
3. Road Runner
4. ECE Single
5. ECE Double
6. Quad
3.125” (79.4 mm) W x 1.5” (38.5 mm)
Flash Patterns
SAE
Pattern
ECE
Pattern 1 Light
x x 353
x x 182
x x 113
x x 62
x x 144
x x 81
6 Flash Patterns
Yes
1 Gen3 LED
Surface Mount
10 - 16 Vdc
less than 0.1 amps
Width x Height x Depth
H x .75” (19.5 mm) D
-20° to +65° C
F.P.M.
(Flashes / Minute)
PATTERN SELECT
1. With light powered, touch White wire to Red Power wire for 1
second.
PATTERN RESET
1. With light powered, touch White wire to Red wire for 3
seconds.
2. Remove White wire from power. Pattern resets to 1.
SYNC MULTIPLE LIGHTS
1. Set up all lights to the same pattern
2. Connect White wires of all lights to sync together.
a. Note, only 6 lights can be synced together.
b. Insulate connections
3. Green Wire Connection
a. For Simultaneous Flashing of a group of lights:
i. Connect all Green wires together of the group of lights
desired to flash in unison.
ii. All Green wires connected together form one light group
b. For alternating flashing of a group of lights:
i. Connect one group of Green wires to Power (+Vdc)
ii. These lights will flash in unison.
iii. Connect one group of Green wires together but leave
floating.
iv. These lights will flash in unison.
v. Together, both light groups will alternate.
vi. For two lights simply connect one Green wire to Power
(+Vdc) and leave the other Green wire floating.
vii. Insulate connections.
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
1.800.338.7337 / www.soundoffsignal.com
IMPORTANT INFORMATION:
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the automated message).
Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsigal.com.
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
EFL1B0(x)_EFL1W0(x) 8.14
Pg. 2
Loading...