SoundOff Signal EL3D02A00 User Manual

INSTALLATION:

OPERATION:

2 MODULE BAR

EL3D02A00(x) - 12V
EL3D02A00(x)-24 - 10-30V

SUPPLIED BAR MOUNTING HARDWARE

Before starting the installation make
certain you have the correct bracket
for your application. A universal Deck/
Dash mount bracket is supplied. For
other mounting brackets, see product
literature or visit our website.

Install the UltraLITE by following the
assembly instructions provided with the
brackets and check for security.

Important: DO NOT over tighten
mounting screws or nuts. This could
cause permanent damage to the light or
bracket. Use appropriate hardware for
mounting.

Universal bracket shown is supplied
but mounting screws are customer
supplied.

1. Connect black wire to ground.

2. Connect red wire to +12Vdc through
5A fuse.

3. Apply +12Vdc to white wire for less
than one second (momentary) to
move forward one pattern.

4. Apply +12Vdc to white wire for one
second (until the lights dim) to move
to the fi rst pattern.

5. Apply +12Vdc to white wire for more
than two seconds (until the lights turn
off) to turn off the UltraLITE.

6. To turn the unit back on, apply +12Vdc
to the white wire momentarily.

WHITE

+12Vdc

5A FUSE

RED
BLACK

2 MODULE UltraLITE

UNIVERSAL BRACKET

Please see reverse for
Technical Specifi cations

Important Information:

• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.

• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.

• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website at www.soundoffsignal.com and select the “Warranty & Returns”

link along the left column of our home page. If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at 1.800.338.7337, press #4 to

skip the automated message. Questions or comments that do not require immediate attention may be emailed to [e-mail].

1.800.338.7337. / www.soundoffsignal.com / Thank you for trusting us with your safety!

WARNING

!

This product contains high intensity LED devices.

To prevent eye damage, DO NOT stare into the

light beam at close range.

EL3DØ2AØØ(x) 10.10

2 MODULE BAR

EL3D02A00(x) - 12V
EL3D02A00(x)-24 - 10-30V

TECHNICAL SPECIFICATIONS

Overall Dimensions: 6.9”L x 1.54”H x 1.7”D

Flash Patterns: 33 fl ash patterns

Input Voltage Range:

Current Consumption: <1 amp*

# of LEDs: 6 Generation 3 LEDs

Operating Temperature: -40º to +65º C

Replacement Modules:

#PUL3M16AMB Amber
#PUL3M16BLU Blue
#PUL3M16GRN Green
#PUL3M16RED Red
#PUL3M16WHT White
See website or catalog for complete list of optional vehicle
specifi c brackets.

10 - 16 Vdc

*Pattern Dependent

Flash Patterns

FPM

Alternating Patterns

1. Quint 70

2. Warp 350

3. Inter-Cycle Flash

4. Double Flash 70

5. Quad Flash 80

6. Power Pulse 180

7. RoadRunner 113

8. Q-Switch

9. RoadRunner Steady Burn 113

10. Quad Steady Burn 80

11. E-Ideal Single Flash 200

12. E-Ideal Double Flash 146

13. Quad2 Flash 67

14. Double2 Flash 95

15. X-Warp

16. X-Double

17. PowerRunner

18. LCR Quint

19. Warp

20. UltraWarp 545

21. Thunder and Lightning

22. LiteSpeed 85

23. SuperSonic 170

24. LCR LiteSpeed

25. SuperSonic Ultra

26. TempoShift

27. TempoShift Warp

28. SBE2 67

29. C

30. U

31. UltraGlow

32. Cyclone

33. Chameleon

3

2

2

(Flashes per Minute)

200

176

EL3DØ2AØØ(x) 10.10