SoundOff Signal Caprice-Intersector Compass Light User Manual

INSTALLATION:

OPERATION:

COMPASS FENDER LIGHT

ECPNTKC1B(xx) - GM CAPRICE

Fig. 1

Mounting

Bracket

Wire

hole

Screws 2x

- Fender Light pre-assembly -

UP

Trim Panel

UP

1. Remove the vent panel from the vehicle
per manufacturers instructions.

2. Run the Intersector Light cable through the
wire hole in the mounting bracket as
shown in figure 1.

4. Install the Intersector Light between the
Trim Panel and the Mounting Bracket. Use
the 2 supplied #6 Torx Screws to attach
the Mounting Bracket to the Trim Panel.
Tighten Snug. See Figure 1.

5. Run the cable assembly into the fender and
install to the power source. See page 2.

6. Snap the Compass Fender Light assembly
to the fender opening.

WARNING

!

This product contains high intensity LED devices. To

prevent eye damage, DO NOT stare into the light

beam at close range.

For details on operation see page with ‘Flash
Patterns’ table on last page.

IMPORTANT:

Power should only be
supplied through RED
WIRE of flasher harness
and must be fused with
a 3A, user supplied,
in-line fuse. Failure to
install this fuse will create
a fire hazard and will
damage the Intersector™
Light. Connecting the
Intersector™ light to any
power source directly
WILL permanently
damage the light and will
void warranty.

IMPORTANT! FOR
PROPER OPERATION
ALL WIRES MUST BE
CONNECTED FROM
FLASHER TO LIGHT
HEAD.

ALL WIRES 22ga

GREEN

BLACK

RED

WHITE

MALE

CONNECTOR

FROM FLASHER

1324

FEMALE

CONNECTOR

1324

RED

BLACK

GREEN

INTERSECTOR

WHITE

LIGHT

Intersector

Light Assembly

(place with label facing down)#6 Torx

Mounting clips must
rest on inside edge
of body opening.

WIRE HOOK-UP TABLE

WIRE COLOR:

(ALL WIRES 20ga)

CONNECT TO:

(FROM FLASHER ONLY)

RED +10-16 Vdc

WHITE Pattern Select / Sync

BLACK Ground (-)

GREEN

Cruise Mode

(+10-16 Vdc)

Fig. 2

1.800.338.7337 / www.soundoffsignal.com

-View from inside of fender-

ECPNTKC1B(xx) 11.12

COMPASS FENDER LIGHT

ECPNTKC1B(xx) - GM CAPRICE

PATTERN RESET

1. Remove power.

2. Place WHITE (sync) wire to ground.

3. With sync wire grounded, re-power RED wire.

4. Maintain for one second (light will dim).

5. Remove power and ground (pattern 1 set).

Tech Specs Intersector™

Flash Patterns:

Light Sync:

Technology:

Mounting:

Input Voltage:

Current Draw:

Dimensions:

Operating Temp.:

14” (356 mm) W x 71” (76 mm) H

-40° to +65° C / -104° to +149° F

Patents:

Parts & Accessories:

LH Intersector Trim Panel PNT3FLTP1L
RH Intersector Trim Panel PNT3FLTP1R
Metal Backing Bracket PNT3FLMB1
Intersector Light PENT3BO(x)

30 Flash Patterns

Yes

9 Gen3 LEDs

Surface Mounts or Deck/ Grille

Bracket Mount

10 - 16 Vdc

less than 1.5 amps

Width x Height x Depth

x 1.5” (38 mm) D

US Design Patent No. D636,113

*Other Patents Pending*

SINGLE LIGHT HEAD SET UP AND PATTERN SELECTION

1. Disconnect WHITE wire from any connections if applicable.

2. Turn Intersector™ LED LIGHT ON by applying power to RED WIRE
from flasher. IMPORTANT NOTE: Power harness with in-line flasher
(PNT(x)FLA) MUST be used between power and light. Any other

flasher WILL cause permanent damage and void warranty.

3. Momentarily touching and removing the WHITE wire to ground
will advance the Intersector™ LED LIGHT to the next flash pattern.
Touching and removing the WHITE wire for more than a few seconds
will allow you to change the Intersector™ LED LIGHT to the previous
pattern. See flash pattern table. Continuing to touch and remove the
WHITE wire to ground will allow you to scroll through the pattern list.
After pattern #30 is reached the list will start over again at pattern
#1.

SINGLE COLOR CONFIGURATIONS

Follow the ID selection steps and set the Intersector™ LED LIGHT to
the following ID:

ID #2 - Single Color ID #4 - Single Color

Single Color - Simultaneous Flash Patterns:

- Set light heads to same ID (#2 or #4).

Single Color - Alternating Flash Patterns:

- Set one light head to ID #2 and another to ID #4.

MULTIPLE LIGHT HEAD SET UP AND PATTERN SELECTION

1. Set ID#
a. Connections
i. RED: +10-16Vdc
ii. WHITE: +10-16Vdc (Note: you will need to disconnect after
power is applied)
iii. BLK: Ground
iv. GREEN: NO CONNECTION REQUIRED FOR ID SELECTION
b. Apply power to unit
c. Without disconnecting power from unit, disconnect WHITE wire
d. Momentarily connect WHITE to Ground to change ID #
i. Identify ID# by number of sequential flashes
ii. Possible ID#s: 2 or 4
e. Disconnect Power to exit ID mode

2. Set Pattern - Must be done individually to each light prior to
syncing
a. RED: +10-16Vdc
b. BLACK: Ground
c. While light is powered, tap WHITE wire to ground to advance to
the next pattern (SEE pattern table at right)
d. Disconnect Power

3. Sync Lights
a. Once desired pattern has been selected for all light heads
connect all white wires and insulate with electrical tape.

4. Connect Master Switch for Application.

Flash Patterns

Pattern Name 1 Light

1. Quint

2. Warp

3. Inter-Cycle Flash

4. Double Flash

5. Quad Flash

6. PowerPulse™

7. RoadRunner™

8. Q-Switch™

9. RoadRunner™ Steady Burn

10. Quad Steady Burn

11. E-Ideal Single Flash

12. E-Ideal Double Flash

13. Quad2 Flash

14. Double2 Flash

15. PowerRunner

16. LCR Quint

3

17. Warp

18. Ultra Warp

19. Thunder & Lightning

20. Lite Speed

21. SuperSonic

22. LCR Lite Speed

23. SuperSonic Ultra

24. Tempo Shift

25. Tempo Shift Warp

26. SBE2

2

27. C

2

28. U

29. Cyclone2

30. Chameleon2

x x x 70

x x x 350

x x

x x x 70

x x x 80

x x x 180

x x x 113

x x

x x 113

x x 80

x x x 200

x x x 146

x x x 67

x x x 95

x x x

x x x

x x x

x x x 545

x x

x x x 85

x x 170

x x x

x x x

x x x

x x x

x x x 67

x x x 200

x x x 176

x x x

x x x

Alternating

2 Lights

Simultaneous

2 Lights

F.P.M.

(Flashes /

Minute)

Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.

1.800.338.7337 / www.soundoffsignal.com

IMPORTANT INFORMATION:

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.

If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the automated message).

Questions or comments that do not require immediate attention may be emailed to [e-mail].

SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.

ECPNTKC1B(xx) 11.12