Sophos XG 230, XG 210, XG 210 Rev. 3, XG 230 Rev. 2 Quick Start Manual

Quick Start Guide

XG 210 Rev. 3, XG 230 Rev. 2

1. Before Deploying

Congratulations on the purchase of your Sophos XG device. This Quick Start Guide describes in short steps how to connect your device and explains how to open the web-based Admin Console from your administration PC. The Admin Console allows you to conﬁgure every aspect of the device.

a) What does the box include

b) Device Images*: Front and Back

Quick Start Guide XG 210 Rev. 3, XG 230 Rev. 2

Before you begin please conﬁrm that you have a working Internet connection and make sure you have the account information available that was provided by your ISP.

* The displayed images are of XG 230 device. The XG 210 device may vary slightly.

Navigation

for LCD

1 x COM (RJ45)

1 further expansion

bays (shown here

with optional FleXi

Port module)

2 x

USB 3.0

Multi-function

LCD display

Micro USB

6 x GbE copper – ﬁxed. Incl. 2 bypass pairs (ports 1/2 and 3/4)

2 x SFP

ports

XG 210/230

(1U rack mount chassis)

This Quick Start Guide and

Security Notes

Micro USB cable

RJ45 Ethernet cable

1 power cable

2 rack mount brackets

1 x HDMI

Connector for redundant

external power supply

Power supply

1 x

USB 3.0

Power switch

XG 210 Rev. 3, XG 230 Rev. 2

2. Mount and connect the device

Please follow the rack mounting instructions as described in the XG Operating Instructions guide* or the separate instructions provided with your rack mount rails.

Connect the ports to the internal and external networks

1. Connect the Port 1/LAN port via a hub or switch to the internal network. For this purpose, use the RJ45 Ethernet cable provided. Note that your Administration PC must also be connected to this network.

2. Connect Port 2/WAN to the external network. The connection to the WAN depends on the type of Internet access.

The XG devices are shipped with the following default settings:

Ethernet Port IP Address Zone

1 172.16.16.16/255.255.255.0 LAN 2 DHCP WAN

Admin Console Username Admin Console Password CLI Console Password

admin admin admin

Default Gateway DNS proxy DHCP service

DHCP Enabled Enabled

Quick Start Guide XG 210 Rev. 3, XG 230 Rev. 2

* Available at sophos.com/get-started-xg

Internet

e.g., DSL modem

Internal network

admin client PC

XG Appliance

Switch

Port 2/WAN

Port 1/

LAN

3. Power Up the Device

Connect the power cable and turn on the device

Connect the device to the power supply using the power cable(s). Turn the device on. The power switch is on the back of the device and is placed next to the power connection. Once the device has booted completely, you’ll hear an acoustic signal: ﬁve beeps in a row.

4. Connect your Administration PC

Administration PC connection properties:

Use the settings below to conﬁgure your (PC/Laptop) network interface:

Ì IP address: 172.16.16.2 Ì Netmask: Enter 255.255.255.0 Ì Default Gateway: Enter the IP address of the device’s

internal network card (Port 1/LAN): 172.16.16.16

Ì DNS Server: Enable this option and enter the IP address of

the internal network card (Port 1/LAN): 172.16.16.16

Connect your PC/Laptop to Port 1/LAN port of the device:

Start the browser and enter the management IP address of the device’s LAN port that your PC is connected to: https://172.16.16.16:4444 (Port 1)

Ì Username: admin Ì Password: admin

Quick Start Guide XG 210 Rev. 3, XG 230 Rev. 2

5. Setup the device

a) Register the Device

If you have not previously registered your device with your Sophos ID, you will see a registration screen. The device requires Internet connectivity for it to be registered with your Sophos ID. You can adjust the network settings of the device’s interfaces by clicking “Basic Setup” so that the device can connect to the Internet.

After clicking “Register Device”, you are redirected to the Sophos.com. If you already have a Sophos ID, enter your login credentials under “Sign in with your Sophos ID”. If you are a new user, sign up for a Sophos ID by entering the details under “Create Sophos ID”.

Click “Continue” to complete the registration process. Please wait while the process completes – it will take a few seconds. After successful registration, you will see a screen with the message, “Your device is now registered”. Please note that you should proceed with the next step i.e. “Synchronize License” only after the device is successfully registered.

b) Synchronize License

Click “Initiate License Synchronization” to fetch license information from Sophos onto the device. After synchronization, you will see a screen with the message, “Synchronization with server was successful”.

c) Start Network Conﬁguration

After successful synchronization, choose “Click Here” on the “Welcome” screen to start your initial device conﬁguration. Use the Network Conﬁguration Wizard to select the deployment mode (Bridge/Gateway) for your device, change the interface(s) IP addresses, default gateway, DNS settings and Date/Time Zone to match your local network settings.

Network Conﬁguration Wizard

Start

Skip

Secure your enterprise with Sophos integrated internet security

Welcome

To your Sophos Device

To get started register your device below. Until you register you may only access

and edit settings in “Basic Setup” and your device will remain unactivated.

XXXXXXXXXXXXXXX

Basic Setup

Serial Number

Device Management

Quick Start Guide XG 210 Rev. 3, XG 230 Rev. 2

d) Device LED Status

Power (LED Display)

Power Supply Acitve Green Power Supply Failure Red SSD Active Blue

LEDs on each RJ45 Ethernet connector

ACT/LNK (Left LED)

Green Constantly 1. The Ethernet port is receiving power.

2. Good connection between the Ethernet port and hub.

Flashing The adapter is sending or receiving network data. The

frequency of the ﬂashes varies with the amount of trafﬁc.

Off 1. The adapter and switch are not receiving power.

2. No connection between both ends of network.

3. Network drivers have not been loaded or do not function correctly.

Speed (Right LED)

Amber On The Ethernet port is operating at 1,000 Mbps. Green On The Ethernet port is operating at 100 Mbps.

Off The Ethernet port is operating at 10 Mbps.

LEDs on each SFP connector

ACT/LNK Green Constantly 1. The SFP connector is receiving power.

2. Good linkage between the SFP connector and hub.

Flashing The adapter is sending or receiving network data. The

frequency of the ﬂashes varies with the amount of trafﬁc.

Off 1. The adapter and switch are not receiving power.

2. No connection between both ends of network.

3. Network drivers have not been loaded or do not function correctly.

Quick Start Guide XG 210 Rev. 3, XG 230 Rev. 2

LAN Bypass (LED Display)

LAN Bypass Active Green LAN Bypass Off Off

Back side

Power Supply Green Constantly Power

Off No power

6. Support and Documentation

For more information and technical support, please visit

www.sophos.com/en-us/support or contact your local Sophos reseller.

Quick Start Guide XG 210 Rev. 3, XG 230 Rev. 2

1. Vorbereitung

Herzlichen Glückwunsch zum Kauf dieser Sophos XG Appliance. Diese Kurzanleitung beschreibt schrittweise, wie Sie die Appliance verbinden, und erläutert, wie Sie über Ihren Administrations-PC die webbasierte Admin Console öffnen. Über die Admin Console können Sie jeden Aspekt der Appliance konﬁgurieren.

a) Verpackungsinhalt

b) Abbildungen der Appliance*: Vorder- und Rückseite

Kurzanleitung XG 210 Rev. 3, XG 230 Rev. 2

Bevor Sie beginnen, vergewissern Sie sich, dass Sie mit dem Internet verbunden sind und die Kontodaten vorliegen, die Sie von Ihrem ISP erhalten haben.

* Die Abbildungen beziehen sich auf die XG 230 Appliance. Die Abbildung für die XG 210 Appliance kann geringfügig abweichen.

Navigation

für LCD

1 x COM (RJ45)

1 weiterer

Erweiterungsschacht

(hier mit optionalem FleXi

Port-Modul abgebildet)

2 x

USB 3.0

Multifunktions-

LCD-Anzeige

Micro USB

6 GbE Kupfer - fest. Einschl. 2 Bypass-Paaren (Ports 1/2 und 3/4)

2 x SFP-

Ports

1 x HDMI

Anschluss für redundante externe Stromversorgung

Netzteil

1 x

USB 3.0

Netzschalter

XG 210/230

(1U Rackmontage-Gehäuse)

Diese Kurzanleitung und

Sicherheitshinweise

Micro USB-Kabel

RJ45 Ethernet-Kabel

1 Netzkabel

2 Rackmontage-Halterungen

XG 210 Rev. 3, XG 230 Rev. 2

2. Appliance montieren und verbinden

Befolgen Sie die Anweisungen für die Rackmontage gemäß der XG Bedienungsanleitung* oder den separaten Anweisungen, die Ihren RackmontageSchienen beiliegen.

Ports mit den internen und externen Netzwerken verbinden

1. Verbinden Sie Port 1/LAN-Port über einen Hub oder Switch mit dem internen Netzwerk. Verwenden Sie hierzu das beiliegende RJ45 Ethernet-Kabel. Beachten Sie, dass Ihr Administrations-PC ebenfalls mit diesem Netzwerk verbunden sein muss.

2. Verbinden Sie Port 2/WAN mit dem externen Netzwerk. Die Verbindung zum WAN hängt von der Art des Internetzugangs ab.

Für die XG Appliances sind werkseitig folgende Standardeinstellungen festgelegt:

Ethernet-Port IP-Adresse Vertrauenswürdige Sites

1 172.16.16.16/255.255.255.0 LAN 2 DHCP WAN

Benutzername Admin Console Kennwort Admin Console Kennwort CLI Console

admin Administrator Administrator

Standard-Gateway DNS-Proxy DHCP-Dienst

DHCP Aktiviert Aktiviert

Kurzanleitung XG 210 Rev. 3, XG 230 Rev. 2

* Abrufbar unter sophos.com/get-started-xg

Internet

z.B. DSL-Modem

Internes Netzwerk

Administrations-Client-PC

XG Appliance

Switch

Port 2/WAN

Port 1/

LAN

3. Appliance einschalten

Schließen Sie das Netzkabel an und schalten Sie die Appliance ein.

Schließen Sie die Appliance mit dem beiliegenden Netzkabel an eine Netzsteckdose an. Schalten Sie die Appliance ein. Der Netzschalter beﬁndet sich auf der Rückseite der Appliance neben dem Netzanschluss. Sobald die Appliance vollständig hochgefahren ist, hören Sie ein akustisches Signal in Form von fünf aufeinanderfolgenden Piepstönen.

4. Administrations-PC verbinden

Verbindungseigenschaften des Administrations-PC:

Verwenden Sie die nachfolgenden Einstellungen für die Konﬁguration Ihrer (PC-/ Notebook-)Netzwerkschnittstelle:

Ì IP-Adresse: 172.16.16.2 Ì Netzmaske: 255.255.255.0 Ì Standardgateway: Geben Sie die IP-Adresse der internen

Netzwerkkarte des Geräts ein (Port 1/LAN): 172.16.16.16

Ì DNS-Server: Aktivieren Sie diese Option und geben Sie die IP-Adresse

der internen Netzwerkkarte ein (Port 1/LAN): 172.16.16.16

Verbinden Sie Ihren PC/Ihr Notebook mit dem Port 1/LAN-Port der Appliance:

Öffnen Sie den Browser und geben Sie die Verwaltungs-IP-Adresse des LAN-Ports der Appliance ein, mit dem Ihr PC verbunden ist: https://172.16.16.16:4444 (Port 1)

Melden Sie sich mit den nachfolgenden Standarddaten an:

Ì Username: admin Ì Passwort: admin

Kurzanleitung XG 210 Rev. 3, XG 230 Rev. 2

+ 22 hidden pages

Sophos XG 230, XG 210, XG 210 Rev. 3, XG 230 Rev. 2 Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual