Model Name Using Similar Mechanism XR-CA630X
Tape Transport Mechanism TypeMG-25F-136
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23 watts per channel minimum continuous average power into 4 ohms,
4 channels driven from 20 Hz to 20 kHz with no more than 5% total
harmonic distortion.
Cassette Player section
Tape track4-track 2-channel stereo
Wow and flutter0.08 % (WRMS)
Frequency response30 – 18,000 Hz
Signal-to-noise ratio
Tuner section
FM
Tuning range87.5 – 107.9 MHz
Antenna terminalExternal antenna connector
Intermediate frequency10.7 MHz/450 kHz
Usable sensitivity8 dBf
Selectivity75 dB at 400 kHz
Signal-to-noise ratio66 dB (stereo),
Harmonic distortion at 1 kHz
Separation35 dB at 1 kHz
Frequency response30 – 15,000 Hz
8.ELECTRICAL PARTS LIST ............................... 32
2
Location of controls
D
S
E
P
D
O
M
MBP
O
F
F
Refer to the pages listed for details.
a MBP button
b MODE (o) button
To change the operation.
c DSPL (display mode change) button
d Volume control dial
e Display window
f Z (eject) button (located on the front side
of the unit, behind the front panel)
g MENU button
To change the menus.
h LIST button
i OPEN button
j OFF (Stop/Power off) button*
k RESET button(located on the front side of
the unit, behind the front panel)
l SOURCE (Power on/Tape/Radio/CD/
MD) button
To select the source.
SOURCE
L
L
R
C
S
SECTION 1
GENERAL
O
P
E
N
L
U
I
S
N
E
M
S
O
U
N
XR-CA650X
m SCRL (scroll) button
n Receptor for the card remote
commander
o SOUND button
p ENTER button
To enter a setting.
q EQ7 button
* Warning when installing in a car without
an ACC (accessory) position on the
ignition switch
After turning off the ignition, be sure to press
and hold (OFF) on the unit until the display
disappears.
Otherwise, the display does not turn off and
this causes battery drain.
T
R
P
E
/
S
C
E
S
I
T
D
SEEK
D
I
S
D
EQ7
T
E
C
S
/
P
E
R
R
E
T
N
E
XR-CA650X
This section is extracted from
instruction manual.
O
P
E
N
L
U
I
N
E
M
S
O
U
N
(+): to select upwards
(SEEK)
(–): to select
leftwards/
.
(–): to select downwards
In menu mode, the currently selectable button(s) of
these four are indicated with a “
r DISC/PRESET buttons (+/–)
To receive preset stations, change the disc*
skip albums*
*1
When an optional CD/MD unit is connected.
*2
Available only when optional CD unit with the
MP3 file control function is connected.
s SEEK buttons (–/+)
To skip tracks, fast-forward, reverse a track,
tune in stations automatically, find a station
manually, and select a setting.
S
T
R
P
E
/
S
C
E
S
I
T
D
SEEK
D
I
S
C
/
D
EQ7
T
E
S
P
E
R
R
E
T
N
E
(DISC/PRESET)
P
/
R
C
E
S
S
I
E
D
T
SEEK
D
I
S
C
T
/
E
P
S
R
E
(DISC/PRESET)
2
, and select a menu.
(SEEK)
(+): to select
rightwards/
>
M
” in the display.
1
,
3
XR-CA650X
Card remote commander RM-X119
DSPL
REPSHUF
1
2
3
4
5
6
MODE
EQ7MBP
LIST
+
DISC
MENU
SOURCE
–
SEEK
SOUND
DISC
VOL
+
SEEK
–
ENTER
ATTOFF
The corresponding buttons of the card
remote commander control the same
functions as those on this unit.
a DSPL button
b Number buttons
(1) REP
(2) SHUF
To store stations, receive stored stations.
c MBP button
d MENU button
e SOURCE button
f SEEK (</,) buttons
g SOUND button
h OFF button
i VOL (+/–) buttons
j EQ7 button
k MODE (o) button
l LIST button
m DISC (M/m) buttons
n ENTER button
o ATT button
Note
If the display disappears by pressing
be operated with the card remote commander unless
(SOURCE)
to activate the unit first.
Tip
See “Replacing the lithium battery” on page 21 for
details on how to replace the batteries.
on the unit is pressed, or a disc is inserted
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Front speaker
Haut-parleur avant
Rear speaker
Haut-parleur arrière
Power amplifier
Amplificateur de puissance
(OFF)
, it cannot
CD/MD changer
Changeur de CD/MD
Rotary commander RM-X4S
Satellite de commande
RM-X4S
2
A
AUDIO OUT REAR
B
Source selector
Sélecteur de source
Cautions
•This unit is designed for negative ground 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all ground wires to a common ground
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
The numbers in the list are keyed to those in the
instructions.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
1
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
*
XA-CA30
BUS CONTROL IN
*
not supplied
non fourni
Connection example ( 2)
Notes (2-A)
• Be sure to connect the ground cord before
connecting the amplifier.
• If you connect an optional power amplifier and
do not use the built-in amplifier, the beep
sound will be deactivated.
)
Tip (2-B-
For connecting two or more CD/MD changers,
the source selector XA-C30 (optional) is
necessary.
Connection diagram (3)
1
To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input
leads.
2
To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
•It is not necessary to connect this lead if
there is no power antenna or antenna
booster, or with a manually-operated
telescopic antenna.
•When your car has a built-in FM/AM
antenna in the rear/side glass, see “Notes on
the control and power supply leads.”
3
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers.
Connecting any other system may damage
the unit.
4
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
•If there is no accessory position, connect to
the +12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to
a metal surface of the car first.
•When your car has a built-in FM/AM
antenna in the rear/side glass, see “Notes on
the control and power supply leads.”
5
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground lead to a
metal surface of the car first.
4
XR-CA650X
3
Supplied with the CD/MD changer
Fourni avec le changeur de CD/MD
from car antenna
à partir de l’antenne de la voiture
AMP REM
Max. supply current 0.3 A
Courant max. fourni 0,3 A
BUS AUDIO
IN
Supplied with XA-C30
Fourni avec le XA-C30
L
R
AUDIO OUT
BUS
REAR
AUDIO IN
Blue/white striped
Rayé bleu/blanc
White
Blanc
White/black striped
Rayé blanc/noir
Gray
Gris
Gray/black striped
Rayé gris/noir
Green
Vert
Green/black striped
Rayé vert/noir
Purple
Mauve
Purple/black striped
Rayé mauve/noir
AUDIO OUT
REAR
Fuse (10 A)
Fusible (10 A)
5
Black
Noir
Blue
Bleu
Red
Rouge
Yellow
Jaune
REMOTE IN
BUS CONTROL IN
Insert with the cord
upwards.
Insérez avec le câble
vers le haut.
Max. supply current 0.1 A
Courant max. fourni 0,1 A
ANT REM
1
2
4
5
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies
+12 V DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the
rear/side glass, connect the power antenna control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing antenna
booster. For details, consult your dealer.
•A power antenna without relay box cannot be
used with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the ground lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit
shares a common negative (–) lead for the right
and left speakers.
• Do not connect the unit’s speaker cords to each
other.
Précautions
•Cet appareil est conçu pour fonctionner sur
courant continu de 12 V CC avec masse
négative.
•Évitez de fixer des vis sur les câbles ou de
coincer ceux-ci dans des pièces mobiles (par
exemple, armature de siège).
•Avant d’effectuer des raccordements, éteignez
le moteur pour éviter les courts-circuits.
•Branchez les fils d’entrée d’alimentation jaune
et rouge seulement après avoir terminé tous les
autres branchements.
•Rassemblez tous les fils de terre en un point
de masse commun.
•Veillez à fixer avec du ruban isolant tout fil
lâche non raccordé.
Remarques sur le cordon d’alimentation
(jaune)
•Lorsque cet appareil est raccordé à d’autres
éléments stéréo, la valeur nominale du circuit
raccordé de la voiture doit être supérieure à la
somme des fusibles de chaque élément.
•Si aucun circuit de la voiture n’est assez
puissant, raccordez directement l’appareil à la
batterie.
Liste des composants ( 1)
Les numéros de l’illustration correspondent à
ceux des instructions.
Attention
Manipulez avec précaution le support 1 pour
éviter de vous blesser aux doigts.
1
Exemple de raccordement (2)
Remarques (2-A)
• Raccordez d’abord le fil de masse avant de
connecter l’amplificateur.
• Si vous raccordez un amplificateur de puissance et
que vous n’utilisez pas l’amplificateur intégré, le
bip sonore est désactivé.
Conseil (2-B- )
Dans le cas du raccordement de deux changeurs de
CD/MD ou plus, le sélecteur de source XA-C30 (en
option) est nécessaire.
Schémas de connexion (3)
1
À un point métallique de la voiture
Branchez d’abord le fil de masse noir et, ensuite,
les fils d’entrée d’alimentation jaune et rouge.
2
Vers le fil de commande de l’antenne électrique
ou le fil d’alimentation de l’amplificateur
d’antenne
Remarques
•Il n’est pas nécessaire de raccorder ce fil s’il n’y
a pas d’antenne électrique ni d’amplificateur
d’antenne, ou avec une antenne télescopique
manuelle.
•Si votre voiture est équipée d’une antenne FM/
AM intégrée dans la vitre arrière/latérale, voir
“Remarques sur les fils de commande et
d’alimentation”.
3
Pour effectuer le raccordement à AMP REMOTE
IN de l’amplificateur de puissance en option
Ce raccordement s’applique uniquement aux
amplificateurs. Le branchement de tout autre
système risque d’endommager l’appareil.
4
À la borne +12 V qui est alimentée quand la clé
de contact est sur la position accessoires
Remarques
•S’il n’y a pas de position accessoires, raccordez
la borne d’alimentation (batterie) +12 V qui est
toujours sous tension.
Raccordez d’abord le fil de masse noir à un
point métallique de la voiture.
•Si votre voiture est équipée d’une antenne FM/
AM intégrée dans la vitre arrière/latérale, voir
“Remarques sur les fils de commande et
d’alimentation”.
5
À la borne +12 V qui est alimentée en
permanence
Raccordez d’abord le fil de masse noir à un point
métallique de la voiture.
Remarques sur les fils de commande et
d’alimentation
• Le fil de commande de l’antenne électrique (bleu)
fournit une alimentation de + 12 V CC lorsque vous
mettez l’appareil sous tension.
• Si votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière latérale, vous devez
raccorder le fil de commande d’antenne électrique
(bleu) ou le fil d’entrée d’alimentation d’accessoire
(rouge) à la borne d’alimentation de l’amplificateur
d’antenne existant. Pour plus de détails, consultez
votre détaillant.
• Une antenne électrique sans boitier de relais ne
peut pas être utilisée avec cet appareil.
Connexion pour la conservation de la mémoire
Lorsque le fil d’entrée d’alimentation jaune est
raccordé, le circuit de la mémoire est alimenté en
permanence même si la clé de contact est sur la
position d’arrêt.
Remarques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettez
l’appareil hors tension.
• Utilisez des haut-parleurs ayant une impédance de
4 à 8 ohms et une capacité adéquate pour éviter de
les endommager.
• Ne raccordez pas les bornes du système de hautparleur au châssis de la voiture et ne raccordez pas
les bornes du haut-parleur droit à celles du hautparleur gauche.
• Ne raccordez pas le câble de masse de cet appareil à
la borne négative (–) du haut-parleur.
• N’essayez pas de raccorder les haut-parleurs en
parallèle.
• Raccordez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avec
amplificateurs intégrés) aux bornes des hautparleurs peut endommager l’appareil.
• Pour éviter tout dysfonctionnement, n’utilisez pas
les fils des haut-parleurs intégrés installés dans
votre voiture si l’appareil partage un fil négatif
commun (–) pour les haut-parleurs droit et gauche.
• Ne raccordez pas entre eux les fils des haut-parleurs
de l’appareil.
5
XR-CA650X
4 AB
c
123
5
Bend these claws
outward for a tight fit, if
1
6 A
TOYOTA
max. size
5 × 8 mm
7
/32 × 11/32 in)
(
Dimensions
max. 5 × 8 mm
(7/32 × 11/32 po)
2
Bracket
Support
Existing parts supplied with your car
Pièces existantes fournies avec la voiture
necessary.
Plier ces griffes vers
l’extérieur pour assurer
une prise correcte si
nécessaire.
to dashboard/center console
au tableau de bord/console centrale
Bracket
Support
2
max. size
5 × 8 mm
7
(
Dimensions
max. 5 × 8 mm
7
(
/32 × 11/32 in)
/32 × 11/32 po)
2
3
3
B
2
3
2
NISSAN
max. size
5 × 8 mm
7
/32 × 11/32 in)
(
Dimensions
max. 5 × 8 mm
(7/32 × 11/32 po)
4
Dashboard
Tableau de bord
4
2
Bracket
Support
Existing parts supplied with your car
Pièces existantes fournies avec la voiture
1
to dashboard/center console
au tableau de bord/console centrale
2
Bracket
Support
max. size
5 × 8 mm
7
/32 × 11/32 in)
(
Dimensions
max. 5 × 8 mm
7
/32 × 11/32 po)
(
6
XR-CA650X
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
•There must be a distance of at least 15 cm
between the cassettes slot of the unit and shift
lever to insert cassette easily. Choose the
installation location carefully so the unit does
not interfere with gear shifting and other
driving operations.
15
cm
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
How to detach and attach the
front panel (4)
Before installing the unit, detach the front
panel.
4-A To detach
Before detaching the front panel, be sure to
press (OFF). Press (OPEN), then slide the front
panel to the right side, and pull out the left side.
4-B To attach
Place the hole
spindle
the left side in.
in the front panel onto the
on the unit as illustrated, then push
Mounting example (5)
Installation in the dashboard
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 2.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
After turning off the ignition, be sure to
press and hold (OFF) on the unit until the
display disappears.
Otherwise, the display does not turn off and this
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ball-point pen, etc., after detaching the
front panel.
Précautions
•Choisissez soigneusement l’emplacement
d’installation pour que l’appareil ne gêne pas
le chauffeur pendant la conduite.
•Évitez d’installer l’appareil dans un endroit
exposé à la poussière, à la saleté, à des
vibrations excessives ou à des températures
élevées comme en plein soleil ou à proximité
de conduits de chauffage.
•Pour garantir un montage sûr, n’utilisez que le
matériel d’installation fourni.
•Pour pouvoir introduire et éjecter aisément la
cassette, il doit y avoir une distance d’au moins
15 cm entre le logement de la cassette de
l’appareil et le levier de changement de
vitesses. Choisissez l’endroit de montage de
telle façon que l’appareil ne gêne pas le
maniement du levier de changement de
vitesses ou toute autre opération de conduite.
15
cm
Réglage de l’angle de montage
Ajuster l’inclinaison à un angle inférieur à 20°.
Retrait et pose de la façade (4)
Avant d’installer l’appareil, retirez la façade.
4-A Pour retirer
Avant de retirer la façade, n’oubliez pas
d’appuyer d’abord sur (OFF). Appuyez sur
(OPEN), puis faites glisser la façade vers la
droite et retirez-la par la gauche
4-B Pour poser
Enfilez l’orifice
l’appareil, comme indiqué sur l’illustration, puis
appuyez sur le côté gauche ou un autre objet
pointu.
de la façade sur la tige de
Exemple de montage (5)
Installation dans le tableau de bord
Installation de l’appareil dans
une voiture japonaise (6)
Cet appareil ne peut pas être installé dans
certaines voitures japonaise. Consultez, dans ce
cas, votre détaillant Sony.
Remarque
Pour éviter tout dysfonctionnement, utilisez
uniquement les vis 2 pour le montage.
Avertissement en cas
d’installation dans une voiture
dont le contact ne comporte
pas de position ACC
(accessoires)
Après avoir coupé le moteur, n’oubliez pas
de maintenir la touche (OFF) enfoncée
sur l’appareil jusqu’à ce que l’affichage
disparaisse.
Sinon, l’affichage n’est pas désactivé et la
batterie du véhicule se décharge.
Touche RESET
Une fois que l’installation et les raccordements
sont terminés, retirez la façade et appuyez sur le
bouton RESET à l’aide d’un stylo à bille ou d’un
autre objet pointu.
7
XR-CA650X
• This set can be disassembled in the order shown below.
2-1.DISASSEMBLY FLOW
FRONT PANEL SECTION
Note: Illustration of disassembly is omitted.
2-2. SUB PANEL ASSY
2-3. MECHANISM DECK (MG-25F-136)
SECTION 2
DISASSEMBLY
SET
(Page 8)
(Page 9)
2-4. MAIN BOARD
(Page 9)
2-5. HEAT SINK (2P)
(Page 10)
Note: Follow the disassembly procedure in the numerical order given.
2-2.SUB PANEL ASSY
4
two claws
1
screw (PTT2.6 × 5)
2
cover
6
sub panel assy
3
screw
(PTT2.6
×
6)
3
two screws
(PTT2.6
5
flexible flat (14core) cable
×
6)
(CN701)
3
screw (PTT2.6 × 6)
4
claw
8
2-3.MECHANISM DECK (MG-25F-136)
4
mechanism deck
(MG-25F-136)
2
connector
(CN351)
3
screw (PTT2.6 × 6)
1
XR-CA650X
flexible board
(CN301)
2-4.MAIN BOARD
2
three ground point
screws
4
main board
3
rubber cap (25)
1
three screws
(PTT2.6 × 8)
9
XR-CA650X
)
2-5.HEAT SINK (2P)
3
heat sink (2P)
1
three screws
(PTT2.6 × 8)
2
two screws
(PTT2.6 × 12)
1
two screws
(PTT2.6 × 8
10
ASSEMBLY OF MECHANISM DECK
• This set can be assembled in the order shown below.
3-1.ASSEMBLY FLOW
3-2. HOUSING
(Page 11)
3-3. ARM (SUCTION)
(Page 12)
3-4. LEVER (LDG-A)/(LDG-B)
(Page 12)
3-5. GEAR (LOADING FT)
(Page 13)
3-6. GUIDE (C)
(Page 13)
XR-CA650X
SECTION 3
3-7. MOUNTING POSITION
OF CAPSTAN/REEL MOTOR (M901)
(Page 14)
Note: Follow the assembly procedure in the numerical order given.
3-2.HOUSING
5 Fit projection on C part.
2 Install the hanger onto
two claws of the housing.
4 Fit claw on B part.
3 Put the housing
under A part.
housing
C part
7 Hold the hanger by bending the claw.
1 Install the catch to the hanger.
hanger
6 Fit projection on D part.
8 Hold the hanger by
bending the claw.
A part
D part
B part
11
XR-CA650X
3-3.ARM (SUCTION)
2 Move the arm (suction) in the arrow
direction and fit on projection.
projection
1 Fit the arm (suction) on the shaft.
3-4.LEVER (LDG-A) / (LDG-B)
shaft A
shaft B
1 Fit the lever (LDG-A) on
shafts A – C and install it.
shaft C
shaft A
shaft B
3 type-E stop ring 2.0
2 Fit the lever (LDG-B) on
shafts A and B and
install it.
12
Loading...
+ 26 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.