Sony XM-N1004 Marketing Specifications
XM-N1004
4/3/2 Channel 1000W Amplier
The Sony® XM-N1004 amplier aords incredible installation exibility and packs quite a
punch.
Bullets
• 70W x 4 RMS at 4 Ohms
• 85W x 4 RMS power at 2 Ohms
• 70W x 2 + 175W x 1 RMS at 4 Ohms
• 170W x 4 max power at 4 Ohms
• 500W x 2 max power at 4 Ohms
1
• 1000 Watts Max Power
• Selectable HPF and LPF
• Automatic Thermal Control
• Single sided connections
Features
Automatic Thermal Control
Other amps thermal protection circuits will simply shut down until they're cool. Sony's Automatic Thermal Control circuit
actually lowers the output levels to reduce amplier temperature so your music continues to play.
Ecient Cooling Design
The unique thermal control chassis is designed to circulate air and cool the amplier for powerful sound output.
High Quality Coponents
Components such as audio capacitors, power MOSFETs and choke coils are carefully selected for high quality sound
reproduction as well as reliability.
LPF / HPF Crossovers
To get the full benet of your speakers, you'll need to send them the appropriate musical frequencies. The integrated High
Pass Filter (HPF) sends everything but the deepest bass to the full-range speakers while the Low Pass Filter (LPF) sends only
the deep bass to the subwoofers.
Single Sided Connections
Single sided connections provide exible installation and multiple mounting options.
Specications
Amplier Section
Max power output 1000W max power
Power Ad Hoc
Speaker
Impedance
70W per channel at 4 Ohms from 20Hz-20kHz with 1%
THD1
2-8 Ohm stereo
4-8 Ohms mono
Audio
Band
Circuit System
Frequency
Response
Harmonic
Distortion
Impedance
Input Level 0.3 - 6.0V (RCA input)
Power Supply
Front crossover: selectable 12dB/oct HPF/LPF @ 80 HZ
Rear crossover: 18dB/oct HPF/LPF @ 80 HZ
OTL (Output Transformerless) circuit
Pulse Power Supply
5 Hz - 50 Khz (+0/-3 db)
0.05% (1kHz @ 4 ohm)
2-8 Ohm stereo
4-8 Ohms mono
OTL (Output Transformerless) circuit
Pulse Power Supply
Signal Circuitry Selectable HPF/LPF crossovers
Signal-to-Noise
Ratio (dB)
93 dBA
Audio Features
Level Control 0.3 - 6.0V (RCA input)
Inputs and Outputs
Audio In RCA Pin Jacks
Audio Out Speaker Terminals
Input(s) RCA Pin Jacks
Line Level Input(s) RCA pin jacks
Output(s) Speaker Terminals
RCA Audio
Input(s)
Pin Jacks: 0.3 - 6V
Power
Current Drain
Input Voltage 10.5-16V Power Supply Voltage
Internal Power
Supply
At rated output: 36A (at 4 Ohms)
Remote Input: 1 mA
OTL (Output Transformerless) circuit
Pulse Power Supply
1. CEA-2006 Compliant — Standardized “Voluntary” Testing Measurement Methods for Mobile Audio Ampliers. This standard advocates a uniform method for determining an amplier’s
RMS power and signal-to-noise ratio. Using 14.4 volts, RMS watts are measured into a 4-ohm impedance load at 1 percent Total Harmonic Distortion (THD) plus noise, at a frequency range
(for general purpose ampliers) of 20 Hz to 20,000 Hz.
© 2013 Sony Electronics Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Sony is a trademark of Sony. All other trademarks are the property
of their respective owners. Features and specications are subject to change without notice. Updated: September 26, 2013
Loading...