Sony XM-GTX1852 Marketing Specifications

XM-GTX1852

2/1 Channel GTX Series Amplier

The XM-GTX1852 amplier aord incredible installation exibility and packs quite a punch. GTX ampliers oer tremendous value including convenience features such as: modern cosmetics, variable cross-overs, multiple channel congurations and singe-side electrical connections to suit almost any application.

Rated Power at 4 Ohm Stereo

185W x 2 RMS (20Hz-20kHz, 1%THD+N, at 4 Ohm, 14.4V)

Maximum Power 4 Ohm Stereo

Maximum power output of 380W per channel at 4 Ohm.

Rated Power at 2 Ohm Stereo

200W x 2 RMS (20Hz-20kHz, 1%THD+N, at 2 Ohm, 14.4V)

Maximum Power 2 Ohm Stereo

Maximum power output of 500W per channel at 2 Ohm.

Rated Power at 4 Ohm Mono

400W x 1 RMS (20Hz-20kHz, 1%THD+N, at 4 Ohm mono, 14.4V)

Maximum Power 4 Ohm Mono

This unit can be used as a bridging amplier with a maximum output of 1000W at 4 Ohms.

High Level Input

Direct connection (High Level Input) can be made with the speaker output of your car audio unit if it is not equipped with RCA line output. Hi-Level Sensing power On feature allows the unit to be activated without need for remote connection.

Internal Crossover

Built in selectable 18 dB/Oct 80Hz LPF.

Specications

Amplier Section

Max power output

Power Ad Hoc

Speaker Impedance

Audio

Band

Circuit System

Frequency Response

Harmonic Distortion

Impedance

Input Level

Noise Level

Power Supply

Audio Features

Level Control

1000W max poer

185W per channel at 4 Ohms from 20Hz-20kHz with 1% THD1

2-8 Ohm stereo 4-8 Ohms mono

Low Pass Filter: 80 HZ, -18dB/oct

"OTL Output Transformerless Circuit Pulse Power Supply"

5-50kHz (+0/-3 dB)

0.05% or less (at 1 kHz, 4 ohm)

2-8 Ohms Stereo, 4-8 Ohms Mono

0.3 - 6.0V (RCA input)

1.2 - 12.0V (High Level Input)

93 dBA

OTL Output Transformerless Circuit Pulse Power Supply

High Level Input: 1.2 - 12V

Inputs and Outputs

Audio In

Audio Out

Input(s)

Line Level Input(s)

Output(s)

RCA Audio Input(s)

Power

Current Drain

Input Voltage

Internal Power Supply

Output Power

Power Requirements

Rated Output

Speaker

Impedance

Speaker Terminal Type

Weights and Measurements

Dimensions (Approx.)

Dimensions (Approx) Depth

Dimensions (Approx) Height

Dimensions (Approx) Width

Weight (Approx.)

Supplied Accessories

RCA Pin Jacks, High Level Input Connector

Speaker Terminals

RCA Pin Jacks and High Level Speaker Input Connector

RCA pin jacks

Speaker Terminals

Pin Jacks: 0.3 - 6V

At rated output:45A (at 4 Ohms) Remote Input: 1 mA

10.5-16V Power Supply Voltage

OTL Output Transformerless Circuit Pulse Power Supply

Maximum Output: 380Wx2 (at 4 Ohm) 1000W x 1 (at 4 Ohms)

12V DC Car Battery (Negative Ground)

185W x 2 (20Hz-20kHz, 1% THD+N, 4 Ohms, 14.4V) 200W x 2 (20Hz-20kHz, 1% THD+N, 2 Ohms, 14.4V) 400W x 1 RMS (20Hz-20kHZ 1.0% THD+N, at 4 Ohms)

2-8 Ohms in Stereo Mode, 4-8 Ohms in Stereo Mode

Output

15 3/4 x 2 1/4 x 11 3/8" (400 x 55 x 288 mm)

11 3/8"

2 1/4"

15 3/4"

7 lbs. 15 oz.

Mounting Screws (4) High Level Input Cord (1) Protection Cap (1)

1. CEA-2006 Compliant — Standardized “Voluntary” Testing & Measurement Methods for

Mobile Audio Ampliers. This standard advocates a uniform method for determining an

amplier’s RMS power and signal-to-noise ratio. Using 14.4 volts, RMS watts are measured

into a 4-ohm impedance load at 1 percent Total Harmonic Distortion (THD) plus noise, at a

frequency range (for general purpose ampliers) of 20 Hz to 20,000 Hz.

written permission is prohibited. Sony, Memory Stick, nav-u, Quick-BrowZer, Walkman,

Xplod, ZAPPIN, and the Sony, nav-u and Xplod logos are trademarks of Sony. iPhone and

iPod are trademarks of Apple Inc., registered in the U.S. and other countries. Bluetooth is

a trademark of Bluetooth SIG, Inc. NAVTEQ Maps & Trac is a trademark of NAVTEQ. All

other trademarks are trademarks of their respective owners. Features and specications

are subject to change without notice. Non-metric weights and measures are approximate.

/Updated: December 14, 2011