XL-DV50H DVD Micro System consisting of XL-DV50H (main
unit), CP-DV50HF (front speakers) and CP-DV50HSW(subwoofer).
• In the interests of user-safety the set should be restored to its original
condition and only parts identical to those specified be used.
• Note for users in U.K.
Recording and playback of any material may require consent which
SHARP is unable to give. Please refer particularly to the provisions of
Copyright Act 1956, the Dramatic and Musical Performers Protection
Act 1956, the Performers Protection Acts 1963 and 1972 and to any
subsequent statutory enactments and orders.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
XL-DV50H
PROBE
AC
OUT
UNIT
SHORT-CIRCUIT
AC POWER
SUPPLY CORD
CONNECT THE PROBE
TO GND OF CHASSIS
SCREW
WITHSTANDING
VOLTAGE TESTER
AudioXL-DV50HService ManualXLDV50HMarketE
CHAPTER 1. GENERAL DESCRIPTION
[1] SAFETY PRECAUTION FOR SERVICE MANUAL
Precaution to be taken when replacing and servicing the Laser Pickup.
The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class 1 Requirements. However, the following precautions must be observed during servicing to protect your eyes against exposure to the Laser beam.
1) When the cabinet has been removed, the power is turned on without a compact disc, and the Pickup is on a position outer than the lead-in position, the Laser will light for several seconds to detect a disc. Do not look into the Pickup Lens.
2) The Laser Power Output of the Pickup inside the unit and replacement service parts have already been adjusted prior to shipping.
3) No adjustment to the Laser Power should be attempted when replacing or servicing the Pickup.
4) Under no circumstances look directly into the Pickup Lens at any time.
5) CAUTION - Use of controls or adjustments, or performance of procedures other than those specified herein may result in hazardous radiation
exposure.
[2] IMPORTANT SERVICE NOTES (FOR U.K.
ONLY)
Before returning the unit to the customer after completion of a repair or
adjustment it is necessary for the following withstand voltage test to be
applied to ensure the unit is safe for the customer to use.
Setting of Withstanding Voltage Tester and set.
Set nameset value
Withstanding Voltage Tester
Test voltage4,240 VPEAK
Set time6 secs
Set current (Cutoff current)4 mA
Unit
Judgment
OK: The “GOOD” lamp lights.
NG: The “NG” lamp lights and the buzzer sounds.
ADVERSEL-SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING.
SE IKKE IND I STRÅLEN-HELLER IKKE MED OPTISKE INSTRUMENTER.
VARO!AVATTAESSA OLET AL TTIINANÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE ÄLÄ TUIJOTA SÄTEESEEN ÄLÄKÄ KATSO SITÄ
OPTISEN LAITTEEN LÄPI.
VARNING-SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ
STRÅLEN GENOM OPTISKT INSTRUMENT.
VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
VARNING - OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN
I DENNA BRUKSANVISNING SPECIFICERAS. KAN
ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR
LASERKLASS 1.
3,000 VRMS
1 – 1
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
[3] SPECIFICATIONS
Except for U.K.
■■
General
Power sourceAC 230 V, 50 Hz
Power consumption Power on: 98 W
Power stand-by: 0.6 W
DimensionsWidth: 160 mm (6-5/16")
Weight6.0 kg (13.2 lbs.)
Height: 240 mm (9-7/16")
Depth: 300 mm (11-13/16")
Amplifier
Output powerFront speakers:
PMPO: 180 W
MPO: 90 W (45 W + 45 W) (DIN 45 324)
RMS: 60 W (30 W + 30 W) (DIN 45 324)
RMS: 45 W (22.5 W + 22.5 W) (DIN 45 500)
Subwoofer:
PMPO: 120 W
MPO: 60 W (DIN 45 324)
RMS: 40 W (DIN 45 324)
RMS: 30 W (DIN 45 500)
Audio output
terminals
Audio input
terminals
Video output
terminals
Front speakers and subwoofer: 6 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Optical digital out put: Square type 1
Video/Auxiliary (audio signal):
500 mV/47 k ohms
SCART output: SCART terminal 1
Video output: RCA type 1
S-video output: S-terminal 1
■■■
Tuner
Frequency rangeFM: 87.5 - 108 MHz
Front speaker
Type2-way type s peaker system
Maximum input
power
Rated input power30 W
Impedance6 ohms
DimensionsWidth: 165 mm (6-1/2")
Weight2.5 kg (5. 5 lbs.)/each
Subwoofer
Type15 cm (6") subwoofer system
Maximum input
power
Rated input power40 W
Impedance6 ohms
DimensionsWidth: 160 mm (6-5/16")
Weight2.9 kg (6. 4 lbs.)/each
XL-DV50H
AM: 522 - 1,620 kHz
(magnetic shield)
4cm(1.5")tweeter
10 cm (4") woofer
60 W
Height: 240 mm (9-7/16")
Depth: 265 m m (10-7/16")
(magnetic shield)
80 W
Height: 240 mm (9-7/16")
Depth: 270 m m (10-5/8")
■
DVD player
Type5-disc multi-play c ompac t disc player
Signal readoutPAL/NTSC colour
Supported disc
types
Video signalHorizontal resolution: 500 lines
Audio signalFrequency
DVD (region number 2, ALL), video CD,
audio CD, CD- R, CD-RW
S/N ratio: 75 dB
characteristics
S/N ratioCD: 95 dB (1 kHz)
Dynamic
range
Total harmonic distortion ratio
Linear PCM DVD:
30 Hz to 20 kHz
(sampling rate: 48 kHz)
30 Hz to 20 kHz
(sampling rate: 96 kHz)
CD: 30 Hz to 20 kHz
Linear PCM DVD: 92 dB
CD: 92 dB
0.14 %
1 – 2
XL-DV50H
For U.K.
■ General
Power sourceAC 230 - 240 V, 50 Hz
Power consumption Power on: 98 W
Power stand-by: 0.6 W
DimensionsWidth: 160 mm (6-5/16")
Weight6.0 kg (13.2 lbs.)
Height: 240 mm (9-7/16")
Depth: 300 mm (11-13/16")
■ Amplifier
Output powerFront speakers:
RMS: 60 W (30 W + 30 W) (10 % T.H.D.)
RMS: 45 W (22.5 W + 22.5 W)
(0.9 % T.H.D.)
Subwoofer:
RMS: 40 W (10 % T.H.D.)
RMS: 30 W (0.9 % T.H.D.)
Audio output
terminals
Audio input
terminals
Video output
terminals
■
DVD player
Type5-disc multi-play compact disc player
Signal readoutPAL/NTSC colour
Supported disc
types
Video signalHorizontal resolution: 500 lines
Audio signalFrequency
Front speakers and subwoofer: 6 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Optical digital out put: Square type 1
Video/Auxiliary (audio signal):
500 mV/47 k ohms
SCART output: SCART terminal 1
Video output: RCA type 1
S-video output: S-terminal 1
DVD (region number 2, ALL), video CD,
audio CD, CD- R, CD-RW
S/N ratio: 75 dB
characteristics
S/N ratioCD: 95 dB (1 kHz)
Dynamic
range
Total harmonic distortion ratio
Linear PCM DVD: 30 Hz to
20 kHz (sampling rate: 48
kHz)
30 Hz to 20 kHz ( sampling
rate: 96 kHz)
CD: 30 Hz to 20 kHz
Linear PCM DVD: 92 dB
CD: 92 dB
0.14 %
■ Tun er
Frequency rangeFM: 87.5 - 108 MHz
AM: 522 - 1,620 kHz
■ Front speaker
Type2-way type s peaker system
Maximum input
power
Rated input power30 W
Impedance6 ohms
DimensionsWidth: 165 mm (6-1/2")
Weight2.5 kg (5.5 lbs.)/each
(magnetic shield)
4cm(1.5")tweeter
10 cm (4") woofer
60 W
Height: 240 mm (9-7/16")
Depth: 265 m m (10-7/16")
■ Subwoofer
Type15 cm (6") subwoofer system
Maximum input
power
Rated input power40 W
Impedance6 ohms
DimensionsWidth: 160 mm (6-5/16")
Weight2.9 kg (6.4 lbs.)/each
(magnetic shield)
80 W
Height: 240 mm (9-7/16")
Depth: 270 m m (10-5/8")
Specifications for this model are subject to change without prior notice.
1 – 3
[4] NAMES OF PARTS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
32145687910
XL-DV50H
Front panel
1. Equaliser Mode Select Button
2. Extra Bass/Demo Mode Butt on
3. Timer Indicator
4. On/Stand-by Button
5. DVD/CD Button
6. Tuner (Band) Button
7. Video/Auxiliary Button
8. Disc Compartment
9. Headphone Socket
10. Remote Sensor
11. Stop or Tuning Down Button
12. Play or Tuning Up Button
13. Chapter (Track) Skip Down or Fast Reverse,
Tuner Preset Down Button
14. Chap ter (Track) Skip Up or Fast Forward,
Tuner Preset Up Button
6. RDS ASPM (Auto Station Programme Memory) Button
7. Direct Number Buttons
8. Chapter (Track) Skip Down or Fast Reverse,
Tuner Preset Down, Time Down Button
9. Cursor Buttons
10. Zoom or Audio Select Button
11. Repeat Play Button
12. F rame Advance or Pause Button
13. A - B Repeat Button
14. Memory/Set Button
15. Top Menu or Return Button
16. Subtitle or Surround Mode Select Button
17. Shift Button
18. Extra Bass or Digital Picture Select Button
19. DVD/CD Button
20. Equaliser Mode S elect or Digital Gamma Button
21. Tuner (Band) Button
22.MenuorOnScreenDisplaySelectButton
23. Di sc Number Select Buttons
24. Direct Button
25. C hapter (Track) Skip Up or Fast Forward,
Tuner Preset Up, Time Up Button
26. Enter Button
27. Angle or NTSC/PAL Select Button
28. Play Button
29. Stop Button
30. Random Button
31. Clear Button
32. Timer/Sleep Button
33. Clock Button
34. Video/Auxiliary Button
35. Volume or Subwoofer Level Up and Down Buttons
1 – 5
AudioXL-DV50HService ManualXLDV50HMarketE
CHAPTER 2. ADJUSTMENTS
[1] ADJUSTMENT
1. TUNER SECTION
fL: Low-range frequency
fH: High-range frequency
• AM IF/RF
Signal generator: 400 Hz, 30%, AM modulated
XL-DV50H
2. DVD/CD SECTION
• Adjustment
Since this DVD/CD system incorporates the following automatic
adjustment functions, readjustment is not needed when replacing
the pickup. Therefore, different PWBs and pickups can be combined freely.
Each time a disc is changed, these adjustments are performed
automatically. Therefore, playback of each disc can be performed
under optimum conditions.
Test StageFrequency Frequency
Display
Setting/
Adjusting
Parts
IF450 kHz1,620 kHzT351*1
AM Band
Coverage
—522 kHz(fL): T306
1.1 ± 0.1 V
AM Tracking 990 kHz990 kHzT302*3
*1. Input: AntennaOutput: TP302
*2. Input: Input is not connectedOutput: TP301
• Check FM VT
Signal generator: 1 kHz, 40 kHz dev., FM modulated
Signal generator: 1 kHz, 40 kHz dev., FM modulated
FrequencyDisplayAdjusting
Parts
98.00 MHz
98.00 MHzVR351Input: Antenna
(30 dBµV)
TUNER PWB-A2
Instrument
Connection
Output: Speaker Terminal
Instrument
Connection
*2
T351
AM IF
VR351
FM MUTE
R350
LEVEL
T306
AM BAND
COVERAGE fL
R356
IC303
TP302
R357
Figure 1 ADJUSTMENT POINTS
20
IC302
T302
AM
Tracking fL
C393
TP301
FE301
SO301
CNP301
2 – 1
XL-DV50H
[2] TEST MODE
The test mode applied to this microcomputer has three modes, namely
the ordinary test mode for adjustment or measurement, the aging test
mode, and the self-diagnosis test mode for self-judgment in case of
final product inspection.
• The TUNER TEST 2 mode is obtained with >> + MEMORY/SET +
ON/STAND-BY. ->Turn off AC in the TEST 2 mode to restore the
initial state.
1. Turning on the test mode
For obtaining each test mode, press the ON/STAND BY button, while
keeping pressing the following two buttons in the ordinary stand-by
mode (power off). In this case, the main unit buttons are valid. When
turning the POWER on with remote control buttons, test modes are not
obtained.
[Ordinary test mode]
1. Tuner Test Mode (TEST 2)........................................................
TUNER(BAND) + DISC1
2. Electronic Volume Test Mode (TEST 3).....................................
TUNING DOWN + VOLUME UP
3. Timer Test Mode (TEST 4).......................................................
TUNING UP + DISC5
4. FL Test Mode (TEST 5)...........................................................
PRESET DOWN + VOLUME DOWN
5. DVD MECHANISM Aging Test Mode (TEST 8).........................
DVD/CD + Equalizer
[Self-diagnosis Test Mode]
1. Button input diagnosis test mode (TEST 6)...............................
PRESET UP + DISC5
Processes are different depending on destinations at initial settings.
2. Tuner Test Mode (TEST 2)
1. Outline of tuner (radio) test mode
The tuner test mode is intended to store the adjustment and measurement frequencies in the preset memory CH. When adjusting
the tuner section in the production line, adjusting personnel are not
required to set frequency.
2. Details of tuner test mode
Press the "TUNER(BAND)" and "VOLUME UP" buttons in POWER
OFF state and turn on the power by the use of "ON/STAND BY"
button to preset and store frequency for adjustment and measurement of destination specified by the AREA terminal in the preset
memory CH. However, Ordinary 1 and Ordinary 2 are stored in the
destinations when the test mode is obtained.
(As for frequencies to be preset and stored for each destination, refer
to item 3.)
The tuner test mode is started from preset No.1.
The operations of test mode are identical with the ordinary operations
of TUNER function. FUNCTION switching is invalid.
It is necessary to discard the content of preset memory when the tuner
test mode is ended; be sure to write "0000" or "1111" bits in the memory to be checked for judging memory error at initial setting and to initialize memory.
When the tuner test mode is obtained, the following display lights for
one second.
Turn off POWER to protect the memory of TEST 2 mode.
Turn off POWER again to obtain the ordinary operation while the
data is stored in the memory (besides TUNER).
If AC OFF state is maintained in this state for about 1/2 day, start is
executed in the initial state.
• To clear the whole memory, insert the AC cord, pressing MEMORY/SET + PLAY.
3. Preset frequencies for various destinations
(random preset memory)
CHBANDFM
1
2
FM STEREO
3
4
5
CHBANDFM
6
7
AM
8
9
10
CHBANDFM
16-35——————
36
37
FM MONO
38
39
40
• The slant line sections of the table store no memory.
FM 87.5 MHz
FM108.0 MHz
FM 98.0 MHz
FM 90.0 MHz
FM106.0 MHz
AM 530 kHz
AM1720 kHz
AM 990 kHz
AM 600 kHz
AM1400 kHz
FM106.0 MHz
FM 90.0 MHz
FM 98.0 MHz
FM108.0 MHz
FM 87.5 MHz
3. Electronic volume Test Mode (TEST 3)
When this test mode is obtained, the following display lights for one
second.
In this mode, volume is Volume -14 dB (STEP 23), FLAT AND X-BASS
ON, and start-up function to DVD/CD, respectively. The button operations in the test mode are the same as those of ordinary operation
except volume UP/DOWN.
1) The display is the same as that of ordinary operation except test
mode setting.
2) Unlike the ordinary state, the volume is controlled with the volume
UP/DOWN button in accordance with the following three steps.
When this test mode is obtained, the following display lights for one
second.
Set the current time and timer time according to the following procedure to reproduce the timer.
1. Set the current time to 1:00, the timer to ON time 1:05, the function
to DVD/CD, and volume to STEP 12, respectively. One minute is
counted as one second, and the timer is reproduced. The fade-in
(when playback is started) is executed at a rate of one step for 1
sec. After completion of fade-in, the fade-out is executed at a rate
of one step for 1 sec (WAIT 1 sec inserted).
After completion of fade-out, the power is turned off (after WAIT 1
sec), and the mode is shifted to the standby.
The display during operation is the same as that of ordinary timer
operation.
5. FL Test Mode (TEST 5)
When the FL test mode is obtained, all the FL segments are lighted.
Then pressing the "PLAY" button switches display as below.
————–
Lighting of all segments
XL-DV50H
6. Button input diagnosis Test Mode (TEST 6)
When the test mode is obtained, the following is displayed.
(STAND-BY AND DEMO OFF STATUS)
This test mode is intended to check whether all the main unit buttons
can be detected. Accordingly, in this test mode, it is checked whether
the "ON/STAND BY" button was pressed after all the buttons shown
below were pressed. If the result is OK, OK is displayed. If any one of
keys was not pressed, an error is displayed. In both cases of OK termination or error termination, the mode is shifted to the standby mode if
the "ON/STAND BY" button is pressed subsequently.
All models using this type of microcomputer are not always provided
with the same buttons. Since the buttons used are different depending
on models, types of buttons to be used are determined by whether
SURROUND, and an electric lid are available at the initial setting by
MODEL port.
The order of buttons to be pressed is not determined. Accordingly, it is
checked whether all buttons have been pressed.
1. PU-IN buttons: REW/PRESET DOWN + STOP
Since this model is provided with SURROUND (HAVE OR NOT),
and electric DVD/CD lid, the following 10 buttons are detected as
all buttons.
The OK/ERROR display of test result is as follows.
Lighting of odd segments
Lighting of even segments
__________
2 – 3
XL-DV50H
7. DVD MECHANISM Aging Test Mode (TEST 8)
OPEN/CLOSE & 3 DISC CHANGER aging test.
DISPLAY:
FUNCTION:
Enter the TEST MODE 8, MCU control the 3 DISC CHANGER OPEN/
CLOSE. After open finished, tray rotate 1 circle (360 degree). Then
close, After close finished, tray rotate 1 circle (360 degree) again.
Request:
Every period include 4 operation. Below is TIMING:
Enter test mode
CHANGER
Find the disc 1 position
open
delay 3S after open finish
rotate 1 circle
close
delay 3S after close finish
rotate 1 circle
2 – 4
DVD Changer
Unit
DVD/CD Disc
Carriage
Drawer
AudioXL-DV50HService ManualXLDV50HMarketE
CHAPTER 3. MECHANICAL DESCRIPTION
[1] REMOVING AND REINSTALLING THE MAIN PARTS
1.
How to remove DVD/CD Disc manually (See Fig. 1,2)
Perform steps 1 to 7 of the disassembly method to remove the DVD
Changer unit.(see page 3-2,3-3)
1. Rotate the gear cam until the arm switch C becomes the position of
the Figure 1.
2. Pull the drawer to the front like the Figure 2.
And the DVD/CD disc on the carriage is taken out.
DVD Changer
Unit
XL-DV50H
Arm switch C
Gear cam
Figure 1
Figure 2
3 – 1
XL-DV50H
Top Cabinet
(A1) x2
ø3x8mm
(A1) x2
ø3x8mm
(B1) x2
ø3x8mm
(B1) x4
ø3x8mm
(B1) x2
ø3x8mm
(A1) x1
ø3x8mm
Top Cabinet
Side Panel
(Left)
Side Panel
(Right)
Rear
Panel
[2] DISASSEMBLY
Caution on Disassembly
Follow the below-mentioned notes when disassembling the unit and
reassembling it, to keep it safe and ensure excellent performance:
1) Be sure to remove the power supply plug from the wall outlet
before starting to disassemble the unit.
2) Take off nylon bands or wire holders where they need to be
removed when disassembling the unit. After servicing the unit,
be sure to rearrange the leads where they were before disassembling.
3) Take sufficient care on static electricity of integrated circuits and
other circuits when servicing.
STEPREMOVALPROCEDUREFIGURE
1Top Cabinet1. Screw.........................(A1) x 51
2Side Panel 1. Screw.........................(B1) x 81
3Rear Panel/Main
PWB
4Tuner PWB1. Screw........................(D1) x 3
5Main PWB1. Screw.........................(E1) x 7
6Transformer1. Screw.........................(F1) x 44
7Front Panel/DVD
Tray Cover
8Chassis2. Screw........................(H1) x 66
9DVD PWB
(Note 1)
10DVD Changer Unit 1. Screw.........................(K1) x 67
11DVD Mechanism1. Screw.........................(L1) x 47
12Display PWB1. Knob.........................(M1) x 1
13Headphones PWB1. Screw........................(N1) x 18
Note 1:
After removing the connector for the optical pickup from the connector,
wrap the conductive aluminium foil around the front end of the connector so as to protect the optical pickup from electrostatic damage.
1. Screw........................(C1) x 8
2. Socket.......................(C2) x 2
2. Socket.......................(D2) x 3
2. Socket.......................(E2) x 8
1. Screw........................(G1) x 2
2. Flat cable..................(G2) x 1
3. Socket.......................(G3) x 1
4. DVD Tray cover.........(G4) x 1
1. Flat cable...................(J1) x 1
2. Socket........................(J2) x 1
3. Screw.........................(J3) x 3
4. Screw.........................(J4) x 4
2. Screw......................(M2) x 10
2
2
3
4
5
7
8
(C2) x1
Main PWB
Rear
Panel
(C1) x7
ø3x8mm
Figure 1
(C2) x1
(D2) x3
(C1) x1
ø3x10mm
Turner PWB
(D1) x3
ø3x8mm
3 – 2
Main PWB
(E1) x1
ø3x10mm
(E1) x4
ø3x10mm
(E2) x1
(E2) x3
Video Terminal
PWB
Figure 2
(E1) x2
ø3x10mm
Figure 3
(E2) x1
Front Panel
(E2) x3
XL-DV50H
(F1) x4
ø4x10mm
Transformer
DVD Changer
Unit
(G2) x1(G3) x1
Figure 4
1
Front Panel
Front Panel
(G1) x2
ø3x10mm
Display PWB
DVD Tray Cover
(H1) x3
ø3x10mm
(J4) x2
ø3x10mm
DVD Changer
Unit
DVD PWB
Bracket
Figure 6
(J3) x3
ø3x10mm
Chassis
(J2) x1
Bracket
(J1) x1
(H1) x3
ø3x10mm
(J4) x2
ø3x10mm
2
DVD Tray Cover
(G4) x1
3
DVD Changer
Unit
Figure 5
CP-DV50HF, CP-DV50HSW
These speaker CP-DV50HF, CP-DV50HSW are available in assembles only and may not be disassembled.
To differentiate the units of resistors, such symbol as K and M are
used: the symbol K means 1000 ohm and the symbol M means
1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type.
• Capacitor:
To indicate the unit of capacitor, a symbol P is used: this symbol P
means micro-micro-farad and the unit of the capacitor without such
a symbol is microfarad. As to electrolytic capacitor, the expression
“capacitance/withstand voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
• Schematic diagram and Wiring Side of P.W.Board for this model
are subject to change for improvement without prior notice.
• The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given.
1. In the tuner section,
( ) indicates AM
< > indicates FM stereo
2. In the main section, a tape is being played back.
3. In the deck section, a tape is being played back.
( ) indicates the record state.
4. In the power section, a tape is being played back.
5. In the CD section, the CD is stopped.
• Parts marked with “ ” () are important for
maintaining the safety of the set. Be sure to replace these parts
with specified ones for maintaining the safety and performance of
the set.