Sony XDR-CD70DAB User Manual
3-214-191-11(1)
© 2007 Sony Corporation Printed in China
XDR-CD70DAB
Dream Machine is a trademark of Sony Corporation.
DAB/FM CD Clock Radio
Operating Instructions
Features
Illumination (High/Low/Off)
Built-in audio cable for digital music players
Built-in CD player with CD-R/RW playback
function
DAB/FM 2-band digital tuner
6 station presets (3 DAB, 3 FM)
Automatic Time/Daylight Saving Time Setting
No Power No Problem Alarm System
Triple time display: A main display for the clock and
two sub-displays for the alarms
Nap Timer (Count Down Timer)
Extendable Snooze time from 10 to 60 min
Precautions
Use the power source specified in “Specifications” to
operate the unit.
The name plate indicating operating voltage, etc. is
located on the bottom of the AC power adaptor.
To disconnect the power cord (mains lead), pull it
out by the plug, not the cord.
Do not carry the unit by the FM/DAB wire antennaDo not carry the unit by the FM/DAB wire antenna
and the AC power cord.
Do not leave the unit in a location near a heat source
such as a radiator or air duct, or in a place subject to
direct sunlight, excessive dust, mechanical vibration,
or shock.
Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on a surface (a rug,
blanket, etc.) or near materials that might block the
ventilation holes such as a curtain.
Should any solid object or liquid fall into the unit,
unplug the unit and have it checked by a qualified
personnel before operating it any further.
When the casing becomes soiled, clean it with a soft
cloth dampened with mild detergent solution. Never
use abrasive cleansers or chemical solvents, as they
may mar the casing.
If you have any questions or problems
concerning your unit, please consult your nearest
Sony dealer.
Troubleshooting
Should the problem persists after you have made the
following checks, consult your nearest Sony dealer.
The clock flashes “AM 12:00” due to a power
interruption.
The battery is low. Replace the battery. Remove the
old battery and install a new one.
The CD, DAB, FM, or buzzer alarm does not sound
at the preset alarm time.
Hasn’t “ALARM A” or “ALARM B” in the display
gone out?
The CD, DAB, or FM alarm is activated but no
sound comes on at the preset alarm time.
Has VOLUME been adjusted ?
The CD player does not operate./
”00” flashes in the display for 5 seconds even
though a CD is inserted.
Did you close the CD compartment lid?
Did you insert the disc correctly?
The disc should be inserted with the label
side up.
Dusty or defective disc — Clean the disc with an
optional cleaning cloth. Wipe the disc from the
center out.
Take out the CD and leave the CD compartment
open for about an hour to allow condensation to
evaporate.
Sporadic loss of sound during CD operation.
Dusty or defective disc — Clean or replace the disc.
Excessively high volume — Reduce the volume.
Strong vibration.
There are scratches on the CD surface.Insert
another CD.
No sound comes from the speakers.
Has VOLUME been adjusted ?
Specifications
CD player section
System: Compact disc digital audio system
Laser diode properties:
Material: GaAlAs
Wavelength: 785 – 800 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
an optical pick-up block with a 7-mm aperture.)
Number of channels: 2
Frequency response: 20 – 20 000 Hz
+1
–2
dB
Wow and flutter: Below measurable limit
Radio section
Frequency range:
FM: 87.5 – 108 MHz
DAB (Band-III): 174.928 (5A) -
239.200 (13F) MHz
DAB (Band-III) frequency table (MHz)
No. Channel Frequency
1 5A 174.928
2 5B 176.640
3 5C 178.352
4 5D 180.064
5 6A 181.936
6 6B 183.648
7 6C 185.360
8 6D 187.072
9 7A 188.928
10 7B 190.640
11 7C 192.352
12 7D 194.064
13 8A 195.936
14 8B 197.648
15 8C 199.360
16 8D 201.072
17 9A 202.928
18 9B 204.640
19 9C 206.352
20 9D 208.064
21 10A 209.936
22 10B 211.648
23 10C 213.360
24 10D 215.072
25 11A 216.928
26 11B 218.640
27 11C 220.352
28 11D 222.064
29 12A 223.936
30 12B 225.648
31 12C 227.360
32 12D 229.072
33 13A 230.784
34 13B 232.496
35 13C 234.208
36 13D 235.776
37 13E 237.488
38 13F 239.200
Antennas:
FM/DAB: FM/DAB wire antenna
General
Time display: 12-hour system
Speaker: 50 mm diam., 8 Ω, cone type (2)
Input: Built-in audio cable with stereo-mini plug (1):
minimum input level 245 mV, impedance
47 kΩ
Power outputs:
1 W + 1 W (at 8 Ω, 10% harmonic distortion)
Power requirements: 230 V AC, 50 Hz
For power backup: 3 V DC, one CR2032 battery
Dimensions:
Approx. 170 136 204 mm (w/h/d) incl.
projecting parts and controls
Mass:
Approx. 1 700 g incl. CR2032 battery
Design and specifications are subject to change
without notice.
No Power No problem is a trademark of Sony Corporation.
Initial Setting for the
Clock
This unit is preset to the current date and time at the
factory, and is powered by the back up battery.
1 Plug in the unit.
The current time appears in the display.
Note
Though the clock is correctly set at the factory,
discrepancies may arise during transport or storage. If
necessary, set the clock to the correct time by referring
to “Setting the Clock Manually” or “Setting the Date
Manually”.
When daylight saving time
(summer time) begins
This model automatically adjusts for daylight saving
time (summer time).
“ ” is displayed from the beginning of daylight saving
time (summer time) and disappears at the end of the
daylight saving time (summer time) automatically.
The summer time adjustment is based on GMT
(Greenwich Mean Time).
Daylight saving time (summer time) begins at: 1:00Daylight saving time (summer time) begins at: 1:00
AM on the final Sunday of March.
Standard time begins at: 2:00 AM on the finalStandard time begins at: 2:00 AM on the final
Sunday of October.
Improving the
Reception
Extend the FM/DAB wire antenna fully to increase
reception sensitivity.
The following conditions may interfere with the
radio reception:
When the unit is placed on a steel desk or metalWhen the unit is placed on a steel desk or metal
surface.
When the unit is near a metal surface (such as aWhen the unit is near a metal surface (such as a
metal wall).
When the unit is near a digital music player that isWhen the unit is near a digital music player that is
turned on.
DAB AUTO SCAN
FM/DABRADIO ON
Initial Setting for the
DAB
When you press FM/DABRADIO ON repeatedly to
select DAB for the first time after you purchase the
unit (or after resetting), DAB Automatic Scan starts
automatically and creates a list of available services.
If you want to run the DAB Auto Scan again or when
the unit is reset, do the following:
1 Press FM/DABRADIO ON repeatedly to
select DAB.
2 Press DAB AUTO SCAN.
“INITIAL?” appears in the display.
3 Press DAB AUTO SCAN again while
“INITIAL?” displays.
Scanning begins. The scanning progress is
indicated by advancing asterisks. Depending on
the DAB services available in your area, scanning
may take a few minutes.
Notes
If no list creates after DAB scan, “NOSIGNAL”If no list creates after DAB scan, “NOSIGNAL”
appears in the display.
To cancel the DAB scan halfway, pressTo cancel the DAB scan halfway, press DAB AUTO
SCAN. Any services received before you cancel are
added to the list of receivable services.
If you change the unit’s location of use, or want toIf you change the unit’s location of use, or want to
add a new service after the initial setting, do steps 1
to 3 of “Initial Setting for the DAB” above.
About the Backup
Battery
To keep good time, this unit contains one CR2032
battery inside of the unit as a backup power source.
The battery keeps the clock operating in the event of a
power interruption.
Knowing when to replace the
battery
When the battery becomes weak, “” appears in the
display.
If a power interruption occurs while the battery is
weak, the current time and alarm will be initialized.
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may cause a fire or
explosion.
Note
If “AM 12:00” flashes in the display when the unit is
connected to AC outlet for the first time, the battery
may be weak. In this case, consult your Sony dealer.
Replacing the battery
1 Keep the AC plug connected to the AC
outlet and use a screwdriver to remove the
screw that secures the battery holder at the
bottom of the unit. (See Fig. -)
2 Push the exhausted battery out from the
bottom of the battery holder and insert a
new battery with the side facing up. (See
Fig. -)
3 Insert the battery holder back into the unit
and secure it with the screw. (See Fig. )
4 Press FM/DABRADIO ON to turn “” off
in the display.
Note
When replacing the battery, do not disconnect AC
plug from AC outlet.
If you do, the current time, alarm and NAP timer will
be initialized.
Battery Warning
If the unit is to be left unplugged for a long time,
remove the battery to avoid undue battery discharge
and damage to the unit from battery leakage.
NOTES ON THE LITHIUM BATTERY
Dispose of the used battery promptly. Keep the
lithium battery out of the reach of children.
Should the battery be swallowed, consult a doctor
immediately.
Wipe the battery with a dry cloth to assure a good
contact.
Be sure to observe correct polarity when installing
the battery.
Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
Do not expose the battery to excessive heat such as
direct sunlight, fire or the like.
WARNING
There is a danger of explosion if the battery is
incorrectly replaced.
Replace only with the same or equivalent type
recommended by the equipment manufacturer.
Push
Lift up with your finger
Display examples
Display indicates
2 (two)
5 (five)
6 (six)
8 (eight)
0 (zero)
A
B
D
G
H
K
M
O
Q
R
S
Z
! or |
”
$
%
,
.
?
@
^
Disposal of Old Electrical & Electronic
Equipment (Applicable in the European
Union and other European countries
with separate collection systems)
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. The
recycling of materials will help to conserve natural
resources. For more detailed information about
recycling of this product, please contact your local
Civic Office, your household waste disposal service or
the shop where you purchased the product.
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To reduce the risk of fire or electric shock, do not
place objects filled with liquids, such as vases, on the
apparatus.
Connect the apparatus to an easily accessible AC
outlet. Should you notice an abnormality in the
apparatus, disconnect the main plug from the AC
outlet immediately.
WARNING
Battery may explode if mistreated.
Do not recharge, disassemble or dispose of in fire.
4 Press VOLUME + or – repeatedly to adjust
the volume.
To Press
Pause CD
Resume play after pause CD again
Cue to the beginning of the
current track (AMS*)
**
Cue to the next track (AMS*) **
Go back at high speed Hold down **
Go forward at high speed Hold down **
Locate a previous track (AMS*) repeatedly**
Locate a succeeding track
(AMS*)
repeatedly**
Stop play
* AMS = Automatic Music Sensor
** These operations are possible during both play and
pause.
During CD playback, every time you press
DISPLAY, the track number appears in the display
for a few seconds.
About CD-Rs/CD-RWs
This unit is compatible with CD-Rs/CD-RWs but
playback capability may vary depending on the quality
of the disc, the recording device and application
software.
Music discs encoded with
copyright protection
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with copyright
protection technologies are marketed by some
record companies. Please be aware that among those
discs, there are some that do not conform to the CD
standard and may not be playable by this product.
To handle compact discs
Do not touch the surface.
Correct
Handle the disc by its edge.
Incorrect
Do not stick paper or
tape on the surface.
Note on DualDiscs
A DualDisc is a two sided disc product which mates
DVD recorded material on one side with digital
audio material on the other side. However, since the
audio material side does not conform to the Compact
Disc (CD) standard, playback on this product is not
guaranteed.
Notes
Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this unit. Attempting to do
so may damage the unit. Do not use such discs.
If you press CD when there is no disc in the CD
compartment, “00” flashes for about 5 seconds in
the display and the unit turns off automatically.
Various Modes of CD Playback
You can play tracks repeatedly or in random order.
Press MODE.
Each press changes the play mode as follows:
Display
Indication
Play
Mode
None (normal play)
All the tracks are played once.
“REP 1” (single repeat)
A single track is played repeatedly.
“REP” (all repeat)
All the tracks are played repeatedly.
“SHUFFLE” (shuffle play)
All the tracks are played once
in random order.
“SHUFFLE REP” (shuffle repeat)
All the tracks are played repeatedly
in random order.
Listening to the Radio
The unit can receive DAB services and FM stations,
for which the Preset and Manual tuning modes can
be used. For DAB services, Alphabetical mode is also
available.
There are the following three tuning modes:
Alphabetical mode (DAB only): For selecting stored
services listed in alphabetical order.
Setting the Brightness
of the Backlight and
Illumination
By pressing the SNOOZE/BRIGHTNESS button, you
can select the brightness level of the backlight and
illumination.
The brightness level of the backlight changes in
conjunction with that of the illumination.
High
High
Middle
Low
Low
OFF
Upper : Backlight level
Lower : Illumination level
While the alarm is sounding, the SNOOZE/
BRIGHTNESS button cannot be used to change the
brightness of the display. It can, however, be used for
the SNOOZE function.
Playing a CD
An 8 cm (3-inch) CD can be played without an
adaptor.
1 Push PUSH OPEN/CLOSE to open the
CD compartment lid and insert a disc.
2 Push PUSH OPEN/CLOSE to close the
CD compartment lid.
Push
Labelled surface up
Close the lid
3 Press CD .
“CD” and “TRACK 01” appear in the display
to indicate that track 1 of the CD is playing.
FM/DAB wire
antenna
AC power cord
Built-in
audio cable
The PRESET TUNING 3 button
has a tactile dot.
The VOLUME + button has a tactile dot.
The CD button has a
tactile dot.
Preset mode: For selecting a favorite stored service
or station (see “Presetting Your Favorite Service or
Station”).
Manual mode (FM only): For adjusting the frequency
manually.
1 Press FM/DABRADIO ON to turn on the
radio.
2 Press FM/DABRADIO ON repeatedly to
select the desired band.
Each press changes the band as follows:
The default setting of the tuning mode is
Alphabetical mode in DAB, and Manual mode
in FM.
If you want to change to Preset mode in both DAB
and FM, see “Tuning in to a Preset Service or
Station (Preset mode)”.
3 Use TUNETIME SET + or – to tune into
the desired service or station.
Two short beeps sound when the lowest ensemble
of DAB or the minimum frequency of FM is
received during tuning.
4 Adjust the volume using VOLUME + or –.
When you release TUNETIME SET + or – after
locating your desired service or station, the display
returns to the current time after about 10 seconds.
To check the ensemble label of a tuned-in service of
DAB or the frequency of a tuned-in station of FM,
press FM/DABRADIO ON and the ensemble label or
the frequency will appear for about 10 seconds.
To turn off the radio, press OFF ALARM RESET.
Notes in DAB usage
Before receiving DAB broadcasts, one or moreBefore receiving DAB broadcasts, one or more
ensembles should be stored in the list by the DAB
scan (See “Initial Setting for the DAB”).
“NO ENS” appears when the ensemble for the“NO ENS” appears when the ensemble for the
selected service cannot be received.
If a selected service finishes broadcasting, soundIf a selected service finishes broadcasting, sound
stops and “NO SRV” appears. In this case, press
TUNETIME SET + or – to select another service.
About the SC (Secondary
Component)
If the selected primary component has a secondary
component, “SC” flashes in the display.
Press TUNETIME SET + or – to receive the desired
secondary component.
“SC” lights up while the secondary component is
being received.
Pressing TUNETIME SET + or – does the following:
Note
When the selected secondary component is finished,
the unit returns automatically to the primary
component.
Presetting Your
Favorite Service or
Station
—Preset Tuning
You can preset up to 3 services in DAB, and 3 FM
stations.
Presetting a Service or a Station
1 Follow steps 1 to 3 in “Listening to the
Radio” and manually tune in the service or
station you wish to preset.
2 Hold down the desired PRESET TUNING
button (1 to 3) until two short beeps sound.
Example 1: The following display appears when
you preset FM 87.50 MHz to PRESET TUNING 2
button for FM.
Frequency of a tuned-in station
PRESET number
The display shows the frequency for about 10
seconds, and then returns to the current time.
Example 2: The following display appears when
you preset BETA_1 to PRESET TUNING 1 button
for DAB.
Ensemble label of a tuned-in service
PRESET Number
The display shows the ensemble label for about 10
seconds, and then returns to the current time.
To preset another service or station, repeat these steps.
To change the preset service or station, tune in the
desired service or station and hold down the desired
PRESET TUNING (1 to 3) until two short beeps sound.
The new service or station will replace the service or
station previously set to the PRESET TUNING button.
Tuning in to a Preset Service or
Station (Preset mode)
1 Press FM/DABRADIO ON to turn on the
radio.
2 Press FM/DABRADIO ON to select the
band.
3 Press the desired PRESET TUNING button.
When pressing TUNETIME SET + or – buttons
during DAB reception, the tuning mode will
change to Alphabetical mode (For more detail, see
“Listening to the Radio” ).
4 Adjust the volume using VOLUME + or –.
After about 4 seconds, the display returns to the
current time.
Note
Holding down the desired PRESET TUNING button
for 2 seconds or more in step 3 will replace the service
or station previously set to the PRESET TUNING
button with the service or station you are tuned in to.
Changing the display
(DAB only)
To change the display mode, press DISPLAY during
DAB reception. The selected display mode remains
even if you turn the unit off and on again, or change
the band.
A dynamic label can be up to 128 characters in length.
An ensemble label can be up to 16 characters in
length.
A component label and service label can be up to 8
characters in length.
Each time you press DISPLAY, the display changes as
follows*:
Component label
Dynamic label
Service label
Ensemble label
Channel label
* When holding down DISPLAY for 2 seconds or
more, the display changes as follows:
Bit rate
Press DISPLAY again.
Signal level
Notes
• If there is no service label, no message will be
displayed.
• If there is no dynamic label, “NO TEXT” will appear.
Listening to the Sound
from a Connected
Optional Component
1 Connect the built-in audio cable with the
stereo-miniplug on the bottom of the unit
to the line output jack or headphones jack
on the optional component (e.g., portable
music player).
To the line
output jack or
headphones
jack
(e.g., portable
music player)
Built-in audio cable
The bottom
of the unit
2 Press AUDIO IN.
“AUDIO IN” appears in the display
3 Play the optional component connected to
the unit’s built-in audio cable.
4 Adjust the volume using VOLUME + or –.
To turn off the sound from the optional component,
press OFFALARM RESET, and then turn off the
optional component.
Notes
Connect the built-in audio cable firmly to prevent a
malfunction.
Keep digital music players away from the speakers.
Setting the Alarm
This CD clock radio is equipped with 4 alarm
modes—CD, DAB, FM and buzzer. Before setting the
alarm, make sure to set the clock (see “Initial Setting
for the Clock”).
To Set the Alarm
1 Hold down ALARM A or B until a short
beep sounds.
The hour flashes in display.
2 Press TUNETIME SET + or – repeatedly
until the desired hour appears.
To set the hour rapidly, hold down TUNETIME
SET + or –.
3 Press ALARM A or B.
A short beep sound and the minute flashes.
4 Repeat step 2 to set the minute and press
ALARM A or B.
A short beep sound and the alarm mode setting
is entered.
5 Press TUNETIME SET + or – repeatedly
until the desired alarm mode flashes.
You can choose one mode among “CD”, “DAB”,
“FM” and “BUZZER”. Set the alarm mode as
follows:
– CD: see “ Setting the CD Alarm”.
– DAB or FM: see “ Setting the DAB/FM
Alarm”.
– BUZZER: see “ Setting the Buzzer Alarm”.
Setting the CD Alarm
For the CD alarm, the track you specified as the wakeup track is played first.
(If the CD play mode is set to “SHUFFLE” or
“SHUFFLE REP”, all the tracks will be played in
random order.)
1 Perform steps 1 to 5 in “To set the Alarm”.
2 Press ALARM A or B to select “CD” alarm
mode.
A short beep sounds and “WAKE UP TRACK”
appears in the display.
3 Press TUNETIME SET + or – to select the
desired wake-up track number.
4 Press ALARM A or B.
A short beep sounds and “WAKE UP VOL”
appears in the display.
5 Press TUNETIME SET + or – to adjust the
volume.
You can also adjust the volume using VOLUME
+ or –.
6 Press ALARM A or B.
Two short beeps sound and the setting is entered.
When “ALARM A” or “ALARM B” does not
appear with “CD” in the display, press ALARM A
or B again.
The CD will play at the set time.
Note
If the CD alarm does not operate because a
disc error occurred, there is no disc, or the CD
compartment lid is open, the buzzer alarm will
operate instead.
Setting the DAB/FM Alarm
For the DAB or FM alarm, the service or station you
specifiy as the wake-up station is played.
1 Perform steps 1 to 5 in “To set the Alarm”.
2 Press ALARM A or B to select “DAB” or
“FM” alarm mode.
After the preset number flashes, “WAKE UP
PRESET” or “WAKE UP -- ” appears in the
display.
3 Press TUNETIME SET + or – to select the
desired wake-up service or station.
The service or station changes as follows:
When DAB is selected
When FM is selected
“– –” is the last service or station received.
You can directly select the desired wake-up service
or station by pressing FM/DABRADIO ON or
the PRESET TUNING button while the “– –”
indication is not displayed.
4 Press ALARM A or B.
A short beep sounds and “WAKE UP VOL”
appears in the display.
5 Press TUNETIME SET + or – to adjust the
volume.
You can also adjust the volume using VOLUME
+ or –.
6 Press ALARM A or B.
Two short beeps sound and the setting is entered.
When “ALARM A” or “ALARM B” does not
appear with “DAB” or “FM” in the display, press
ALARM A or B again.
The radio will turn on at the set time.
Note
If the DAB alarm does not operate (e.g., when the
unit is unable to receive DAB services), the buzzer
alarm will operate instead.
Setting the Buzzer Alarm
1 Perform steps 1 to 5 in “To set the Alarm”.
2 Press ALARM A or B to select “BUZZER”
alarm mode.
Two short beeps sound and the setting is entered.
When “ALARM A” or “ALARM B” does not
appear with “BUZZER” in the display, press
ALARM A or B again.
The buzzer will sound at the set time.
Note
The volume cannot be set for the buzzer alarm.
ALARM ON—
Press ALARM A or B to activate the alarm setting.
If “ALARM A” or “ALARM B” does not appear in the
display, the alarm setting is not activated. You can only
check the alarm setting when it is activated.
Example: The following display shows the current
time and the CD ALARM A for 7:00 am.
If you set the CD alarm and there is no disc in the
CD player, the buzzer alarm will sound instead at the
time set.
In case of the alarm, the beeping of the alarm becomes
louder after every few seconds in three progressive
stages.
Note
When Alarm A and B are set for the same time, Alarm
A takes precedence.
PUSH OPEN/CLOSE
VOLUME +/–
Battery
compartment
SNOOZE/BRIGHTNESS
Setting the Date
Manually
1 Plug in the unit.
2 Hold down DATE until a short beep sounds.
The year starts to flash in the display.
3 Press TUNETIME SET + or – repeatedly to
set the year.
4 Press DATE.
5 Repeat steps 3 and 4 to set the month and
the day, and then press DATE.
Two short beeps sound and the year, month, and
day are set.
Setting the Clock
Manually
1 Hold down CLOCK until a short beep
sounds.
The hour starts to flash in the display.
2 Press TUNETIME SET + or – repeatedly to
set the hour.
3 Press CLOCK.
4 Repeat steps 2 and 3 to set the minutes, and
then press CLOCK.
Two short beeps sound and the seconds start
incrementing from zero.
Notes
The clock setting will be cancelled if you press OFF
ALARM RESET while setting the clock.
If you do not press a button for about 1 minute while
setting the clock, the clock setting will be cancelled.
To display the year and date
Press Date once for the date, and within 2 seconds
press it again for the year.
The display shows the date or year for about 4 seconds
and then changes back to the current time.
To change to daylight saving
time (summer time) indication
Hold down OFF ALARM RESET and and DATE until
two short beeps sound.
“ ” is displayed, “ON” appear for a few seconds,
and then the time changes to daylight saving time
(summer time).
To deactivate the daylight saving time (summer time)
function, hold down OFF ALARM RESET and and
DATE until two short beeps sound again.
“OFF” appears for a few seconds, and then “ ”
disappears.
To Doze for a Few More Minutes
Press SNOOZEBRIGHTNESS once.
“10” appears in the display and the CD, DAB, FM,
or BUZZER alarm stops. Every time you press
SNOOZEBRIGHTNESS, the snooze time changes as
follows:
The display shows the snooze time for a few seconds,
and then returns to the current time. When you
press SNOOZEBRIGHTNESS after the current time
appears, the snooze time goes back to 10 minutes
again.
The maximum length of the snooze time is 60
minutes.
To Stop the Alarm
Press OFF ALARM RESET to turn off the alarm.
The alarm will sound again at the same time the next
day.
ALARM OFF—
Press ALARM A or B to deactivate the alarm setting.
The CD, DAB, FM, or buzzer alarm turns off
automatically after 60 minutes.
Note on the alarm in the event of a power
interruption
In the event of a power interruption, the alarm will
work until the battery is totally discharged. But
following functions are different:
During a power interruption, the display indications,
backlight and illumination will not light up.
If the alarm mode is set to CD, DAB, or FM, it will
change to BUZZER automatically.
If a power interruption occurs while the alarm is
sounding, the alarm will stop.
If OFF ALARM RESET is not pressed, the alarm
sounds for about 5 minutes.
If “” appears in the display, the alarm will not
sound in the event of power interruption. Replace
the battery if “” appears.
If a power interruption occurs while the buzzer
alarm is sounding, the SNOOZE/BRIGHTNESS
button will not operate.
Using the NAP Timer
(Count Down Timer)
The NAP timer sounds the buzzer after a preset
duration has elapsed.
Press NAP repeatedly until the desired duration is
displayed.
Every press changes the display as follows:
“ ” appears and the NAP time is displayed for a
few seconds.
NAP timer starts counting down.
When the selected NAP duration has ended, buzzer
sounds, and “ ” flashes in the display.
The buzzer turns off automatically after about 60
minutes.
To Stop the NAP Timer
Press NAP or OFF ALARM RESET to turn off the
buzzer.
To Deactive the NAP Timer
Press NAP.
“ ” goes off in the display.
Setting the Sleep Timer
The sleep timer allows you to fall asleep to the sound
of a CD, DAB, FM, or input from the AUDIO IN
function. It does this by automatically turning off the
CD, DAB, FM, or input from the AUDIO IN function
after a preset duration.
Press SLEEP during CD, DAB, FM, or optional
component play.
You can set the sleep timer to durations of 90, 60, 30,
or 15 minutes. Every press changes the duration as
follows:
“SLEEP” will appear in the display when the duration
is set.
The CD, DAB, FM, or the optional component will
play for the set duration, and then shut off.
To Turn Off the Sleep Timer
function
Press OFF ALARM RESET.
AUDIO IN
Loading...