To reduce the risk of fire or electric shock, do not expose the TV to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR
PRECAUCION
RIESGO DE CHOQUE ELECTRICO
NO ABRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
Note to the CATV Installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building as close to the point of
cable entry as practical.
SAFETY PRECAUTIONS
Operate the TV only on 120 V AC.
One blade of the power plug is wider than the other for safety purposes and will fit into the power
outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.
If any liquid or solid object falls into the TV, unplug it and have it checked by qualified personnel
before operating it further.
CAUTION
When using TV games, computers, and similar products with your TV, keep the brightness
and contrast functions at low settings. If a fixed (non-moving) pattern is left on the screen for
long periods of time at a high brightness or contrast setting, the image can be permanently
imprinted onto the screen. Continuously watching the same channel can cause the imprint of
station logos onto the TV screen. These types of imprints are not covered by your warranty
because they are the results of misuse.
To reduce the risk of electric shock, do not use this polarized plug with an
extension cord, receptacle, or other outlet unless the blades can be fully inserted
to prevent blade exposure.
User Guide
You are cautioned that any changes or modifications not expressly approved in this manual
could void your authority to operate this equipment.
NOTIFICATION
This equipment has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference with radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antennas.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Protecting the TV
To prevent internal heat build-up, do not block the ventilation openings.
Do not install the TV in a hot or humid place, or in a place subject to excessive dust or mechanical
vibration.
Note on Caption Vision
This television receiver provides display of television closed captioning in accordance with
§ 15.119 of the FCC rules.
Use of this television for other than private viewing of programs broadcast on UHF or VHF or
transmitted by cable companies for the use of the general public may require authorization
from the broadcaster-cable company and/or program owner.
Owner’s Record
The model and serial numbers are located on the front cover of this manual and at the rear of
your TV.
Trademarks and Copyrights
ENERGY STAR® is a registered mark.
As an ENERGY STAR® Partner, Sony has determined that this product or product
model meets the ENERGY STAR
®
guidelines for energy efficiency.
Connecting Additional Equipment
Important Safeguards
For your protection, please read these instructions completely, and keep this manual for future
reference. Carefully observe and comply with all warnings, cautions and instructions placed
on the set, or described in the operating instructions or service manual.
WARNING
To guard against injury, the following basic safety precautions should be observed in the
installation, use, and servicing of the set.
Use
Power Sources
This set should be operated only from the
type of power source indicated on the serial/
model plate. If you are not sure of the type of
electrical power supplied to your home,
consult your dealer or local power company.
For those sets designed to operate from
battery power, refer to the operating
instructions.
For the set with a polarized AC power cord
plug
This plug will fit into the power outlet only
one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet,
try reversing the plug. If the plug still fails to
fit, contact your electrician to have a suitable
outlet installed. Do not defeat the safety
purpose of the polarized plug by forcing it
in.
Grounding or Polarization
This set is equipped with a polarized AC
power cord plug (a plug having one blade
wider than the other), or with a three-wire
grounding type plug (a plug having a third
pin for grounding).
Refer to the following instructions:
Alternate Warning
For the set with a three-wire grounding type
AC plug
This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet,
contact your electrician to have a suitable
outlet installed. Do not defeat the safety
purpose of the grounding plug.
User Guide
Overloading
Do not overload wall outlets, extension
cords or convenience receptacles beyond
their capacity, since this can result in fire or
electric shock. Always turn the set off when
it is not to be used. When the set is left
unattended and unused for long periods of
time, unplug it from the wall outlet as a
precaution against the possibility of an
internal malfunction that could create a fire
hazard.
Do not disconnect the antenna or the power
cord during a heavy storm. Lightning may
strike while you are holding the cable or
cord, causing serious injury. Turn off your
TV and wait for the weather to improve.
Object and Liquid Entry
Never push objects of any kind into the set
through the cabinet slots as they may touch
dangerous voltage points or short out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the set.
Attachments
Do not use attachments not recommended
by the manufacturer, as they may cause
hazards.
Do not place any objects, especially heavy
objects, on top of the set. The object may fall
from the set, causing injury.
Cleaning
Unplug the set from the wall outlet before
cleaning or polishing it. Do not use liquid
cleaners or aerosol cleaners. Use a cloth
lightly dampened with water for cleaning
the exterior of the set.
If a snapping or popping sound from a TV
set is continuous or frequent while the TV is
operating, unplug the TV and consult your
dealer or service technician. It is normal for
some TV sets to make occasional snapping
or popping sounds, particularly when being
turned on or off.
Installation
Always use two or more people to lift or
move the set. The set is heavy and the
bottom surface is flat. Serious injury can
result from trying to move the set by
yourself alone, or from unsteady handling.
Install the set on a stable, level surface.
Water and Moisture
Do not use power-line operated sets near
water — for example, near a bathtub,
washbowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, etc.
Connecting Additional Equipment
Accessories
Do not place the set on an unstable cart,
stand, tripod, bracket, table, or shelf. The set
may fall, causing serious injury to a child or
an adult, and serious damage to the set. Use
only a cart or stand recommended by the
manufacturer for the specific model of TV.
Any mounting of the product should follow
the manufacturer’s instructions, and should
use a mounting accessory recommended by
the manufacturer. An appliance and cart
combination should be moved with care.
Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
Disconnect all cables and cords from the set
before attempting to move the set.
Do not allow children or pets to climb up
onto, or push against, the set. The set may
fall, causing serious injury.
Ventilation
The slots and openings in the cabinet and in
the back or bottom are provided for
necessary ventilation. To ensure reliable
operation of the set, and to protect it from
overheating, these slots and openings must
never be blocked or covered.
•Never cover the slots and openings
with a cloth or other materials.
•Never block the slots and openings by
placing the set on a bed, sofa, rug or
other similar surface.
•Never place the set in a confined space,
such as a bookcase or built-in cabinet,
unless proper ventilation is provided.
•Do not place the set near or over a
radiator or heat register, or where it is
exposed to direct sunlight.
Power-Cord Protection
Do not allow anything to rest on or roll over
the power cord, and do not place the set
where the power cord is subject to wear or
abuse.
User Guide
Grounding or Polarization
This set may be equipped with a polarized alternating current line plug (a plug having one
blade wider than other). This plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the
plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Antennas
Outdoor Antenna Grounding
If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system
should not be located in the vicinity of overhead power lines or other electric light or power
circuits, or where it can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE
TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS
CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.
Be sure the antenna system is grounded so as to provide some protection against voltage
surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in USA
and Section 54 of the Canadian Electrical Code in Canada provides information with respect
to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode.
Antenna Grounding According to the NEC
Antenna Grounding According to the National Electrical Code, ANSI/NFPA 70.
ANTENNA
LEAD IN
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC - NATIONAL ELECTRIC CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ARTICLE 250, PART H)
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
Lightning
For added protection for this television receiver during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage to the receiver due to lightning and powerline surges.
Connecting Additional Equipment
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer
servicing to qualified service personnel
under the following conditions:
•When the power cord or plug is
damaged or frayed.
•If liquid has been spilled into the set or
objects have fallen into the product.
•If the set has been exposed to rain or
water.
•When the set exhibits a distinct change
in performance — this indicates a need
for service.
Servicing
Do not attempt to service the set yourself
since opening the cabinet may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
Replacement Parts
When replacement parts are required, be
sure the service technician certifies in
writing that he has used replacement parts
specified by the manufacturer that have the
same characteristics as the original parts.
Unauthorized substitutions may result in
fire, electric shock, or other hazards.
•If the set has been subject to excessive
shock by being dropped, or the cabinet
has been damaged.
•If the set does not operate normally
when following the operating
instructions. Adjust only those controls
that are specified in the operating
instructions. Improper adjustment of
other controls may result in damage
and will often require extensive work
by a qualified technician to restore the
set to normal operation.
Safety Check
Upon completion of any service or repairs to
the set, ask the service technician to perform
routine safety checks (as specified by the
manufacturer) to determine that the set is in
safe operating condition, and to so certify.
When the set reaches the end of its useful
life, improper disposal could result in a
picture tube implosion. Ask a qualified
service technician to dispose of the set.
User Guide
Contents
Introduction
Introducing the FD Trinitron WEGA Features.................................................1
Batteries for the Remote Control ..........................................................................2
About this Manual ..................................................................................................2
Front Panel Menu Controls ...................................................................................2
®
Connecting Your TV
TV Rear Panel ..........................................................................................................3
Index .............................................................................................................................35
User Guide
Introduction
Introduction
Congratulations on your purchase of the Sony FD Trinitron WEGA . Before you begin using
this manual, please check the model number located on the rear of your TV or on the front
cover of this manual.
®
®
Introducing the FD Trinitron WEGA Features
Some of the features you will enjoy include:
FD Trinitron FLAT CRT— Technologically advanced tube delivers a picture with
uncompromising accuracy and outstanding image detail.
Y, P B, PR Inputs — A component video input connection for a superior picture quality.
Parental Control (V-Chip) — A tool to help parents monitor what their children watch on
TV by establishing rating limits.
Favorite Channels — Instant access to your favorite channels with the touch of a button.
Energy Star® — A recognized symbol of energy efficiency.
Direct MTS— Allows direct access for changing your Multi-Channel TV Sound: Stereo,
Mono, or Auto SAP (Second Audio Program) with the touch of a button.
Trilingual Menus — Choose between English, French, or Spanish menus.
Front Panel Controls— Allows access to the on-screen menus without the use of a remote
control.
Front A/V Inputs— A quick connection for video games, camcorders, stereo/mono
equipment, or headphones.
Auto Mute— A friendly feature designed to automatically mute your TV when no signal
is received.
1
Operating Instructions
Batteries for the Remote Control
Insert two AA (R6) batteries (supplied) into the remote control using the following illustration
as a guide.
Under normal conditions, batteries will last up to six months. If the remote control does
not operate properly, the batteries might be worn out.
If you will not be using the remote control for an extended period of time, remove the
batteries to avoid possible damage from battery leakage.
About this Manual
This manual provides instructions to help you enjoy your new TV. It shows you how to
connect to an antenna or cable, cable box, VCR, DVD, satellite receiver, stereo system, or
camcorder. Once you’re connected, follow the instructions and use the remote control to
access the on-screen menus.
The TV front and rear panels illustrated in this manual are for KV-24FS100. The front and
rear panels on your TV may not look exactly like those illustrated.
Front Panel Menu Controls
F
F
The front Audio/Video panel controls allows you to access the menu without the remote
control. Press to display the on-screen menu. Use the and buttons on the front
Audio/Video panel instead of the
on the front Audio/Video panel instead of the
Press again when the setting or adjustment is complete.
To navigate the menus with your remote control, see “Using the Menus” on page 17.
2
Fand f buttons on the remote control. Use the button
G, g, and buttons on the remote control.
ConnectingYour TV
Connecting Your TV
Read this section before setting up your TV for the first time. This section covers basic
connections in addition to any optional equipment you may be connecting.
TV Rear Panel
1
2
4
3
JackDescription
1S VIDEOConnects to the S VIDEO OUT jack on your VCR or other video
equipment that has S VIDEO. S VIDEO provides better picture
quality than the VHF/UHF jacks or the video input jack. S VIDEO
does not provide sound; the audio cables must still be connected.
2 VHF/UHFConnects to your VHF/UHF antenna or cable.
3 VIDEO/
AUDIO (L/R)
4 Y, P B, PR/
L, R
The rear panels illustrated in this manual are for KV-24FS100. The rear panels on your TV
may not look exactly like those illustrated.
Connects to the AUDIO and VIDEO output jacks on your VCR or
other video equipment. A second video input jack (VIDEO 2) is
located on the front panel of the TV. These AUDIO/VIDEO input
jacks provide better picture quality than the VHF/UHF jack.
Connects to the component video Y, PB, PR to AUDIO L and R
output jacks on your DVD player or Digital Set-top box.
3
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.