Sony KP 43T90, WEGA KP 53V90, KP-48V90, KP-53S76, WEGA KP 61V90 User Manual

Projection TV

Operating Instructions

KP-43T90 KP-48V90 KP-53S76 KP-53V90 KP-61V90

4-082-881-13(1)

WARNING

To prevent fire or shock hazard, do not expose the TV to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE DE CHOC ELECTRIQUE,

NE PAS OUVRIR

PRECAUCION

RIESGO DE CHOQUE ELECTRICO

NO ADRIR

NO ABRIR

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

To prevent electric shock, do not use this polarized AC plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

CAUTION

When using TV games, computers and similar products with your projection TV, or viewing a TV station whose logo always stays on the screen, keep the brightness and contrast functions at low settings. If a fixed (nonmoving) pattern such as a station logo is left on the screen for long periods of time, especially at a high brightness or contrast setting, the image can be permanently imprinted onto the screen. These types of imprints are not covered by your warranty.

Note on Caption Vision

This television receiver provides display of television closed captioning in accordance with §15.119 of the FCC rules.

Note on convergence adjustment

Before you use your projection TV, make sure to adjust convergence. For details, see page 19.

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Use of this television receiver for other than private viewing of programs broadcast on UHF or VHF or transmitted by cable companies for the use of the general public may require authorization from the broadcaster/cable company and/or program owner.

NOTIFICATION

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antennas.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty and your authority to operate this equipment.

This document is for the remote control RM-Y906 MODELS: KP-43T90, KP-48V90, KP-53S76, KP-53V90,

Please keep this notice with the instruction manual.

KP-61V90

As an ENERGY STAR Partner, Sony Corporation has determined that this product meets the ENERGY STAR

ATTENTION

Pour prévenir les chocs électriques, ne pas utiliser cette fiche polarisée avec un prolongateur, une prise de courant ou une autre sortie de courant, sauf si les lames peuvent être inserées à fond sans en laisser aucune partie à decouvert.

Remote Control

In the instructions that follow, we will refer to the buttons on your remote control. Keep this flap unfolded and use this page for reference.

VCR/DVD/MDP

operation buttons

SLEEP (page 22)

PICTURE MODE (pages 20, 26)

0 – 9 buttons

JUMP (page 21)

(pages 22, 27)/

(for SAT, page 49)

INDEX

(pages 23, 26, 27)

VOL +/– (page 20)

MUTING

(page 20)

SYSTEM OFF

(page 22)

(page 48)

CC (page 22)

(page 20)

RESET

CODE SET

(pages 47, 49)

DVD/

MUTING

VTR

SYSTEM

OFF

DVD/VTR SAT/CABLE

TV/VTR

FREEZE

POSITION ACTIVE

SLEEP

PICTURE

MODE

JUMP

INDEX

RESET

VOL CH

CODE SET

FUNCTION

SAT/

CABLE

SWAP PIP

AUDIO

ANT

ENTER

POWER

TV/VIDEO

DISPLAYMTS/SAP

GUIDE

POWER

(pages 20, 48, 49)

FUNCTION

(pages 20, 48, 49)

PIP operation buttons

(page 23)

TV/VIDEO

(pages 21, 23)

ANT (page 24)

DISPLAY

(page 21)

MTS/SAP

(pages 22, 27)

ENTER (page 20)

GUIDE (page 49) V/v/B/b and

buttons

(page 25)

MENU (page 25)

CH +/– (page 20)

Getting to know the buttons on the remote control

Names of the buttons on the remote control are presented in different colors to represent the available functions.

Button color

Transparent .... Press to select the component

Green ............... Buttons relevant to power

Label color

White ............... TV/VTR (VCR)/MDP/DVD

Yellow .............. PIP operation buttons

Blue .................. SAT operation buttons

Green ............... S-Link operation buttons

Pink .................. DVD Player operation buttons

For a detailed explanation of most buttons, see “Watching the TV” on page 20.

you want to control; e.g. VTR (VCR)/MDP/DVD Player, SAT (satellite receiver)/ CABLE, or projection TV.

operations, like turning the projection TV, SAT/CABLE, or VTR (VCR)/MDP/DVD Player on or off

Player/SAT (satellite receiver

)/CABLE operation

buttons

Table of Contents

Welcome! ........................................ 1

Using This Manual .......................... 1

Precautions...................................... 2

Important Safeguards .................... 3

For Safety ...................................................... 6

Installing and Connecting the

Projection TV....................... 7

Carrying Your Projection TV ...................... 7

Installing the Projection TV ........................ 7

Connector Types .......................................... 8

Making Connections ................................... 8

Connecting directly to a cable or an

antenna ............................................... 8

Cable or antenna .................................... 9

Cable and antenna ................................. 9

Connecting a cable box .........................9

Cable box and cable .............................. 9

Connecting a cable TV system/

antenna to a VCR ............................ 10

Connecting a VCR and projection TV

to a cable box ................................... 10

Connecting a satellite receiver (SAT) 12

Connecting a satellite receiver (SAT)

and a VCR ........................................ 13

Connecting a DTV (digital television)

receiver ............................................. 14

Connecting a camcorder ..................... 14

Connecting a DVD Player .................. 15

Connecting a DVD Player with

component video output

connectors ........................................ 15

Connecting an audio system ............. 16

Connecting a Sony SAVA series

speaker system ................................ 17

Basic Set Up................................... 18

Using the Remote Control ........................18

Setting Up the Projection TV

Automatically ................................... 18

Adjusting the Convergence Automatically

(FLASH FOCUS) .............................. 19

Using Your New Projection TV .... 20

Watching the TV ........................................ 20

Watching Two Programs at One Time

— PIP ................................................. 23

Adjusting Your SET UP (menus) ... 25

Learning Menu Selection ..........................25

Using the Video Menu......................... 26

Using the Audio Menu ........................27

Using the Timer Menu........................ 29

Using the Channel Set Up Menu ...... 30

Setting and Selecting Favorite Channel .. 32

Using the Set Up Menu ......................34

Using the Parental Control Feature......... 36

Activating the Parental Control

Feature .............................................. 36

Selecting a Custom Rating

in U.S.A............................................. 38

Selecting a Custom Rating

in Canada ......................................... 41

Changing the Password ..................... 42

What the Ratings Mean ............................ 43

Ratings in U.S.A. .................................. 43

Ratings in Canada ............................... 45

Open Here For Table of Contents and Remote Control Graphics

Welcome!

Using This Manual

Operating Video Equipment ........... 47

Setting the Manufacturer's Code ................ 47

Operating a Cable Box or Satellite

Receiver (SAT) ...................... 49

Setting the Manufacturer's Code ................ 49

Troubleshooting .............................. 50

Specifications ................................... 52

Index .............................................. 53

Owner’s Record

The model and serial numbers are located at the rear of the projection TV, below the Sony logo, on the sticker, and also on the TV box (white label). Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. Serial No.

Thank you for purchasing the Sony Color Rear Video Projection TV.

This manual is for models KP-43T90, KP48V90, KP-53S76, KP-53V90, KP-61V90.

Model KP-53V90 is used for illustration purposes.

The features you will enjoy include:

• FLASH FOCUS, allowing you to adjust convergence automatically.

• Parental Control, enabling you to block programs that you feel are unsuitable for your children.

• Picture-in-Picture (PIP), allowing you to view another TV channel, video or cable image as a window picture.

• Favorite Channel, allowing you to view and choose from eight of your favorite channels

• Y/P

B/PR inputs for DVD Player and DTV

receiver connections.

• Three AUDIO/VIDEO/S VIDEO inputs.

We recommend that you carefully review the contents of the following four sections in the order provided to ensure that you fully understand the operation of your new projection TV.

1 Installing and Connecting the Projection

This section guides you through your initial set up. It shows you how to install your projection TV, to connect your new components and to connect to the antenna and cable.

2 Basic Set Up

This section teaches you the basic skills needed to operate your new projection TV, including Auto Set Up. It shows you how to operate the remote control’s special functions.

3 Using Your New Projection TV

This section shows you how to begin using your new projection TV. It shows you how to use your remote control’s features.

4 Adjusting Your Set Up (menus)

This section teaches you how to access on-screen menus and adjust your projection TV’s settings.

Instructions in this manual are written for the remote control. Similar controls may be found on the projection TV console.

Installing and Connecting the Projection TV (continued)

Precautions

Safety

• Operate the projection TV only on 120 V AC.

• The plug is designed, for safety purposes, to fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

• If any liquid or solid object should fall inside the cabinet, unplug the projection TV immediately and have it checked by qualified service personnel before operating it further.

• If you will not be using the projection TV for several days, disconnect the power by pulling the plug itself. Never pull on the cord.

Note on cleaning

Clean the cabinet of the projection TV with a dry soft cloth. To remove dust from the screen, wipe it gently with a soft cloth. Stubborn stains may be removed with a cloth slightly dampened with solution of mild soap and warm water. Never use strong solvents such as thinner or benzine for cleaning.

If the picture becomes dark after using the projection TV for a long period of time, it may be necessary to clean the inside of the projection TV. Consult qualified service personnel.

Installing

• To prevent internal heat buildup, do not block the ventilation openings.

• Do not install the projection TV in a hot or humid place, or in a place subject to excessive dust or mechanical vibration.

• Avoid operating the projection TV at temperatures below 5° C (41° F).

• If the projection TV is transported directly from a cold to a warm location, or if the room temperature changes suddenly, the picture may be blurred or show poor color. In this case, please wait a few hours to let the moisture evaporate before turning on the projection TV.

• To obtain the best picture, do not expose the screen to direct illumination or direct sunlight. It is recommended to use spot lighting directed down from the ceiling or to cover the windows that face the screen with opaque drapery. It is desirable to install the projection TV in a room where the floor and walls are not of a reflective material.

Important Safeguards

For your protection, please read these instructions completely, and keep this manual for future reference.

Carefully observe and comply with all warnings, cautions and instructions placed on the set, or described in the operating instructions or service manual.

WARNING

To guard against injury, the following basic safety precautions should be observed in the installation, use, and servicing of the set.

Use

Power Sources

This set should be operated only from the type of power source indicated on the serial/

model plate. If you are not sure of the type of electrical power supplied to your home, consult your dealer or local power company. For those sets designed to operate from battery power, refer to the operating instructions.

Grounding or Polarization

This set is equipped with a polarized AC power cord plug (a plug having one blade wider than the other), or with a three-wire grounding type plug (a plug having a third

pin for grounding). Follow the instructions below:

For the set with a polarized AC power cord plug

This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the polarized plug by forcing it in.

Alternate Warning For the set with a

three-wire grounding type AC plug

This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the grounding plug.

Overloading

Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since this can result in fire or electric shock.

Always turn the set off when it is not to be used. When the set is left unattended and unused for long periods of time, unplug it from the wall outlet as a precaution against the possibility of an internal malfunction that could create a fire hazard.

Object and Liquid Entry

Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the set.

Attachments

Do not use attachments not recommended by the manufacturer, as they may cause hazards.

(continued)

Important Safeguards (continued)

Installing and Connecting the Projection TV (continued)

Cleaning

Unplug the set from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the set.

If a snapping or popping sound from a projection TV set is continuous or frequent while the projection TV is operating, unplug the projection TV and consult your dealer or service

It is normal for some projection TV sets to make occasional snapping or popping sounds, particularly when being turned on or off.

technician.

Installation

Water and Moisture

Do not use power-line operated sets near water— for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool,

etc.

Accessories

Do not place the set on an unstable cart, stand, table or shelf. The set may fall, causing serious injury to a child or an adult, and

serious damage to the set. Use only a cart or stand recommended by the manufacturer for the specific model of projection TV.

An appliance and cart

combination should be

moved with care. Quick

stops, excessive force, and

uneven surfaces may

cause the appliance and

cart combination to

overturn.

Ventilation

The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of the set, and to protect it from overheating, these slots and openings must never be blocked or covered.

- Never cover the slots and openings with a cloth or other materials.

- Never block the slots and openings by placing the set on a bed, sofa, rug or other similar surface.

- Never place the set in a confined space, such as a bookcase, or built-in cabinet unless proper ventilation is provided.

- Do not place the set near or over a radiator or heat register, or where it is exposed to direct sunlight.

Power-Cord Protection

Do not allow anything to rest on or roll over the power cord, and do not place the set where the power cord is subject to wear or abuse.

Antennas Outdoor Antenna Grounding — If an

outdoor antenna is installed, follow the precautions below.

An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits.

WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.

Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Section 810 of the National Electrical Code (NEC) in USA and Section 54 of the Canadian Electrical Code in Canada provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Antenna Grounding According to the NEC — Refer to section 54-300 of Canadian

Electrical Code for Antenna Grounding.

Antenna lead-in

Ground damps

Electric service equipment

NEC: National Electrical Code

wire Antenna discharge

unit (NEC Section 810-20)

Grounding conductors (NEC Section 810-20)

Ground damps

Power service grounding electrode system (NEC Art 250 Part H)

Lightning

For added protection for this television receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the receiver due to lightning and power-line surges.

Service

Damage Requiring Service

Unplug the set from the wall outlet and refer servicing to qualified service personnel under the following conditions:

- When the power cord or plug is damaged or frayed.

- If liquid has been spilled into the set.

- If the set has been exposed to rain or water.

- If the set has been subject to excessive shock by being dropped, or the cabinet has been damaged.

Important Safeguards (continued)

Installing and Connecting the Projection TV (continued)

- If the set does not operate normally when following the operating instructions. Adjust only those controls that are specified in the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the set to normal operation.

- When the set exhibits a distinct change in performance—this indicates a need for service.

Servicing

Do not attempt to service the set yourself since opening the cabinet may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Replacement Parts

When replacement parts are required, be sure the service technician certifies in writing that he has used replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.

Safety Check

Upon completion of any service or repairs to the set, ask the service technician to perform routine safety checks (as specified by the manufacturer) to determine that the set is in safe operating condition, and to so certify.

When the set reaches the end of its useful life, improper disposal could result in a picture tube implosion. Ask a qualified service technician to dispose of the set.

For Safety

Be careful when moving the projection TV

When you place the projection TV in

position, be careful not to drop it on your foot or fingers. Watch your footing while installing the projection TV.

Carry the projection

TV in the specified

manner

If you carry the

projection TV in a

manner other than the specified manner and without the specified number of persons, it may drop and a serious injury may be caused. Be sure to follow the instructions mentioned below.

- Carry the projection TV with the specified number of persons.

- Do not carry the projection TV holding the speaker grill.

- Hold the projection TV tightly when carrying it.

Installing and Connecting the Projection TV

60°

Carrying Your Projection TV

Carrying the projection TV requires three or more people.

For KP-48V90/53S76/53V90/61V90

The projection TV has been equipped with casters for easy movement on a hard surface. Please move your projection TV using the casters.

Installing the Projection TV

Recommended viewing area (Horizontal)

min. 2.4m (approx. 8 ft.)

min. 2.1m (approx. 7 ft.)

min. 1.8m (approx. 6 ft.)

min. 1.5m (approx. 5 ft.)

43"

60°

53"

48"

Recommended viewing area (Vertical)

min. 2.4m (approx. 8ft.)

61"

min. 2.1m (approx. 7ft.)

53"

min. 1.8m (approx. 6ft.)

61"

48"

min. 1.5m (approx. 5ft.)

43"

20°

Installing and Connecting the Projection TV (continued)

Connector Types

You may find it necessary to use some of the following connector types during set up.

Coaxial cable

Standard TV cable and antenna cable

Plug Type

Push into connection.

Screw-on Type

Screw into connection.

S Video cable

High quality video cable for enhanced picture quality

Audio/Video cable

Video - Yellow Audio (Left) - White Audio (Right) - Red

Some DVD Players and DTV Receivers are equipped with the following three video connectors.

Y - Green P

B (CB, Cb or B–Y) - Blue

R (CR, Cr or R–Y) - Red

Align guides and push into connection.

Push into connection.

CONTROL S cable

Sony cable for CONTROL S connection. This feature is exclusive to Sony products and allow greater control of all Sony equipment.

Push into connection.

About the CONTROL S OUT jack

To control other Sony equipment with the projection TV’s remote control, connect the CONTROL S IN jack of the equipment to the CONTROL S OUT jack on the projection TV with the CONTROL S cable.

(Rear of projection TV)

AUX

CONVERTER

VIDEO 1

CONTROL S

OUT

CONTROL S

VIDEO 4VIDEO 3

COMPONENT

OUT

AUDIO

(VAR/FIX)

S VIDEO

VIDEO

(MONO)

AUDIO

OUT

VHF/UHF

(MONO)

AUDIO

Making Connections

Connecting directly to a cable or an antenna

The connection you choose will depend on the cable found in your home. Newer homes will be equipped with standard coaxial cable (see

A); older homes will probably have 300 -

ohm twin lead cable (see B); still other homes may contain both (see Use 75-ohm coaxial cable for improved picture quality (see

• VHF only or

• VHF/UHF or

• Cable

A).

75-ohm coaxial cable

• VHF only or

• UHF only or

• VHF/UHF

300-ohm twin lead cable

Antenna connector

C ).

(Rear of

projection TV)

VHF/UHF

(Rear of

projection TV)

VHF/UHF

75-ohm coaxial cable

• VHF

and

• UHF

300-ohm twin lead cable

(Rear of

projection TV)

VHF/UHF

EAC-66 U/V mixer (not supplied)

Cable or antenna

This is the simplest connection. Connection is made directly from the cable or antenna to the projection TV.

(Rear of projection TV)

Coaxial cable

VHF/UHF

Cable and antenna

You may find it convenient to use the following set up if your cable provider does not feature local channels that you are able to receive using an antenna.

(Rear of projection TV)

Coaxial cable

(No connection “TO CONVERTER” in this case)

Antenna cable

AUX

TO CONVERTER

VHF/UHF

Select Cable or ANT mode by pressing ANT on the remote control.

Connecting a cable box

Some pay cable TV systems use scrambled or encoded signals that require a cable box* to view all channels.

Also, set “Cable” to “On” in the Channel Set Up menu (page 31).

(Rear of projection TV)

Coaxial cable

OUTIN

*Cable box

VHF/UHF

Cable box and cable

Some pay cable TV systems use scrambled or encoded signals requiring a cable box* only for certain channels (e.g. HBO, SHOWTIME, etc.)

*Cable box

Scrambled channels

75-ohm coaxial cable (not supplied)

CATV cable

(unscrambled channels)

For this set up, you can switch between scrambled channels (through your cable box), and normal (CATV) channels by pressing ANT on your remote control.

Notes:

• You may be able to program your Sony remote control to operate your cable box. (see “Operating a Cable Box or Satellite Receiver (SAT)” on page 49)

• During PIP or Favorite Channel viewing, the AUX input can only be viewed in the main picture.

• AUX input cannot be viewed in the PIP window.

(Rear of projection TV)

AUX

TO CONVERTER

(Signal)

VHF/UHF

Installing and Connecting the Projection TV (continued)

Connecting a cable TV system/ antenna to a VCR

1 Attach the coaxial cable from the

incoming cable connection or antenna to VHF/UHF IN on the VCR.

2 Using a coaxial cable, connect VHF/UHF

OUT on the VCR to VHF/UHF on the projection TV.

3 Using AUDIO and S VIDEO* cables,

connect AUDIO and S VIDEO OUT on the VCR to AUDIO and S VIDEO IN on the projection TV (White-AUDIO Left, RedAUDIO Right**).

Connecting a VCR and projection TV to a cable box

1 Connect the single (input) jack of the

splitter to the incoming cable connection, and connect the other two (output) jacks (using the coaxial cable) to IN on the cable box and VHF/UHF on the projection TV.

2 Using a coaxial cable, connect OUT on the

cable box to VHF/UHF IN on the VCR.

3 Using AUDIO and S VIDEO* cables,

connect AUDIO and S VIDEO OUT on the VCR to AUDIO and S VIDEO IN on the

projection TV (White-AUDIO Left, RedAUDIO Right**).

S VIDEO

Disconnect all power sources before making any connections.

(Rear of projection TV)

AUX

VIDEO 1

S VIDEO

VIDEO

AUDIO

(MONO)

VIDEO 4VIDEO 3

COMPONENT

VIDEO

AUDIO-L

AUDIO-R

(Rear of projection TV)

VIDEO 1

COMPONENT

VIDEO

AUDIO-L

AUDIO-R

VIDEO 4VIDEO 3

S VIDEO

VIDEO

AUDIO

(MONO)

OUT

AUDIO

(VAR/FIX)

(MONO)

AUDIO

VMC-810S/820S (not supplied)

OUT

AUDIO

(VAR/FIX)

(MONO)

AUDIO

VMC-810S/820S (not supplied)

CONVERTER

VHF/UHF

YC-15V/30V

(not supplied)

AUX

CONVERTER

VHF/UHF

YC-15V/30V

(not supplied)

Coaxial cable

AUDIO R AUDIO L VIDEO

LINE

LINE OUT

Coaxial cable

AUDIO R AUDIO L VIDEO

LINE

LINE OUT

S VIDEO

OUT

VHF/UHF

VCR

Splitter (not supplied)

S VIDEO

OUT

VHF/UHF

OUT

VCR

Cable box

Cable/ Antenna

Note:

• To view scrambled channels through the cable box, select the video input which the cable box is connected to by pressing TV/ VIDEO.

* If your VCR is not equipped with S VIDEO, use

a VIDEO cable (yellow) instead of the S VIDEO cable.

** If you are connecting a monaural VCR, connect

only the single audio output to the left (MONO) input on the projection TV.

Installing and Connecting the Projection TV (continued)

Connecting a satellite receiver (SAT)

1 Connect the cable from the satellite

antenna to the satellite receiver.

2 Attach the coaxial cable from the incoming

cable connection or antenna to VHF/UHF on the projection TV.

3 Using AUDIO and S VIDEO cables,

connect AUDIO and S VIDEO OUT on the satellite receiver to AUDIO and S VIDEO IN on the projection TV (White-AUDIO Left, Red-AUDIO Right).

Note:

• To view input from the satellite receiver, select the video input which the satellite receiver is connected to by pressing TV/ VIDEO on the remote control.

Disconnect all power sources before making any connections.

(Rear of projection TV)

VIDEO 1

S VIDEO

VIDEO

AUDIO

(MONO)

VIDEO 4VIDEO 3

COMPONENT

S VIDEO AUDIO-L AUDIO-R

CONVERTER

OUT

AUDIO

(VAR/FIX)

(MONO)

AUDIO

RK-74A (not supplied)

YC-15V/30V (not supplied)

AUX

VHF/UHF

Cable/ Antenna

Satellite antenna cable

SAT

SATELLITE IN

LINE OUT

AUDIO R AUDIO L VIDEO

S VIDEO

VHF/UHF

OUT

Connecting a satellite receiver (SAT) and a VCR

1 Connect the cable from the satellite

antenna to the satellite receiver.

2 Attach the coaxial cable from the

incoming cable connection or antenna to VHF/UHF IN on the VCR.

3 Using a coaxial cable, connect VHF/UHF

OUT on the VCR to VHF/UHF on the projection TV.

4 Using AUDIO and S VIDEO* cables,

connect AUDIO and S VIDEO OUT on the satellite receiver to AUDIO and S VIDEO IN on the VCR.

5 Using AUDIO and S VIDEO* cables,

connect AUDIO and S VIDEO OUT on the VCR to AUDIO and S VIDEO IN on the projection TV (White-AUDIO Left, RedAUDIO Right).

If your VCR is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable.

Note:

• To view input from the satellite receiver or VCR, select the video input which your satellite receiver or VCR is connected to by pressing TV/VIDEO on the remote control.

S VIDEO

Disconnect all power sources before making any connections.

(Rear of projection TV)

AUX

CONVERTER

VIDEO 1

S VIDEO

VIDEO

AUDIO

VIDEO 4VIDEO 3

OUT

AUDIO

(VAR/FIX)

(MONO)

COMPONENT

VIDEO

AUDIO-L

AUDIO-R

AUDIO

(MONO)

VHF/UHF

Satellite antenna cable

VMC-810S/ 820S (not supplied)

VCR

VMC-810S/820S (not supplied)

YC-15V/30V (not supplied)

SATELLITE IN

AUDIO R AUDIO L VIDEO

LINE OUT

AUDIO R AUDIO L VIDEO

LINE

LINE OUT

Coaxial cable

SAT

VHF/UHF

S VIDEO

OUT

YC-15V/

30V (not supplied)

S VIDEO

VHF/UHF

OUT

Cable/ Antenna

Installing and Connecting the Projection TV (continued)

Connecting a DTV (digital television) receiver

Before connecting, be sure to read the Operating Instructions of the DTV receiver.

1 Attach the coaxial cable from the roof

antenna to VHF/UHF IN (DTV) on the DTV receiver.

2 Using AUDIO and S VIDEO cables, connect

AUDIO and S VIDEO OUT on the DTV receiver to AUDIO and S VIDEO IN on the projection TV (White-AUDIO Left, RedAUDIO Right).

Notes:

• Your DTV receiver must be able to support 480i video format output.

• If your DTV receiver supports 480i signal from YP

BPR, you can connect Y, PB and PR of

VIDEO OUT on the DTV receiver to Y, P and PR of VIDEO 4 IN on the projection TV using VIDEO cables.

Connecting a camcorder

Use this connection to view a picture directly from your camcorder.

1 Using AUDIO and S VIDEO* cables, connect

AUDIO and S VIDEO OUT on the camcorder to AUDIO and S VIDEO IN inside the dropdown panel on the front of the projection TV (White-AUDIO Left, Red-AUDIO Right**).

2 Press VIDEO 2 to select the video inputs

from a camcorder.

* If your camcorder is not equipped with S VIDEO,

use a VIDEO cable (yellow) instead of the S VIDEO cable.

** If you are connecting a monaural camcorder,

connect only the single audio output to the left (MONO) input on the projection TV.

S VIDEO

VIDEO

AUDIO

(MONO)

VIDEO 1

AUDIO-R

AUDIO-L

(Rear of projection TV)

VIDEO 4VIDEO 3

OUT

AUDIO

(VAR/FIX)

COMPONENT

(MONO)

AUDIO

RK-74A (not supplied)

S VIDEO

Disconnect all power sources before making any connections.

YC-15V/30V (not supplied)

ACCESS CARD

DIGITAL

AUDIO

OUT

(OPTICAL)

123

S VIDEO

AUDIO

AUDIO/VIDEO OUT

VIDEO

MONO

TEL LINE

AUX

CONVERTER

VHF/UHF

DTV receiver

VHF/UHF IN

VHF/UHF IN (DTV)

SATELLITE IN

VHF/SATELLITE

OUT

LOW SPEED DATA

VCR

CONTROL

VGA OUT

Roof antenna

YC-15V/30V (not supplied)

VIDEO AUDIO-L AUDIO-R

AUDIO

VIDEO

S VIDEO

VIDEO 2 INPUT

(MONO)

(Front of projection TV)

VMC-810S/820S (not supplied)

Camcorder

Audio/ video outputs

S VIDEO OUT

+ 40 hidden pages