Sony Wega KD-32DX51 AUS Operating Instructions Manual
2-149-435-11
Trinitron
Integrated Digital
Television
Operating Instructions
Before operating the TV, please read the ‘Safety Informatio n’ sec ti on of th is
manual. Retain this manual for future reference.
KD-32DX51 AUS
© 2004 Sony Corporation
Thank you for choosing this
FD Trinitron Integrated
Digital Television
Before operating the TV, please read this instruction
manual thoroughly and retain it for future reference.
All instructions in this manual refer to buttons on the
supplied remote control un less stated otherwise.
The model and serial numbers are located on the back
of the TV. Record the serial number in the space
provided below. Refer to these numbers whenever
you call your dealer regarding this product.
Model No. KD-32DX51AUS
Serial No. ______________
Serial No.
TRINITRON COLOUR TV
MODEL NO.
220-240V 50/60Hz
SER. No.
6000001
Please note: The information in this manual was correct at the time of
going to print. However, s ome minor chan ges may hav e been made late
in the product’s development. All illustrations in this manual have been
created during the product’s development and may differ slightly to the
finished p roduct.
KD-
MANUFACTURED IN UK
PRODUCT BY SONY CORP
TOKYO / JAPAN
32DX51AUS
88W
N50
Table of Contents
Table of Contents
Safety Information
Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Getting Started
Checking the accessories supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Inserting batteries into the remote control . . . . . . . . . . . . . . . . . . . . . . 6
Connecting an aerial and VCR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Switching on the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Automatically tuning the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Switching between digital and analogue mode . . . . . . . . . . . . . . . . . . 8
Basic Operation
Overview of the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overview of the TV buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Everyday use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Screen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Advanced Operation
The Channel Index menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
The Digital Electronic Programme Guide (EPG) . . . . . . . . . . . . . . . . . 16
The Info menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
The Main menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Detail Set-up menu (Digital) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Using the TV menu system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Picture Adjustment menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Sound Adjustment menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Detail Adjustment menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Timer menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Set Up menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Manual Programme Preset menu. . . . . . . . . . . . . . . . . . . . . . . . . 24
Detail Set Up menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Connecting Other Equipment
Overview of the rear sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Overview of the front sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Connecting other equipment to the TV. . . . . . . . . . . . . . . . . . . . . . . . .28
Viewing pictures from equipment connected to the rear sockets. . . . . 28
Viewing pictures from equipment connected to the front sockets . . . . 28
Remote control of other equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Programming the remote control. . . . . . . . . . . . . . . . . . . . . . . . . . 29
Controlling a DVD player. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Controlling a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Additional Information
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
How to lift the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover
Table of Contents
3
Safety Information
SU-32XL1
4 Safety Information
Safety Information
Due to the unique design of this TV, highly recommend you use their designated stand SU-32XL1.
This set is to operate on a 220-240V AC
supply only. Take care not to connect too
many appliances to the same power socket
as this could result in fire or electric shock.
Do not open the cabinet and the rear cover
of the TV. Refer to qualified service
personnel only.
For environmental and safety reasons, it is
recommended that the TV is not left if
standby when unused. Disconnect from the
mains. However, some TVs may have
features which need the TV to be left in
standby to work correctly. The instructions
in this manual will inform you if this applies.
For your own safety, do not touch any part
of the TV, power lead or aerial lead during
lightning storms.
Never push objects of any kind into the set
as this could result in a fire or electric shock.
Never spill liquid of any kind on the set. If
any liquid or solid object does fall through,
do not operate the TV. Have it checked
immediately by qualified personnel.
To prevent fire or shock hazard, do not
expose the TV to rain or moisture.
Do not cover the ventilation openings of the
TV. For ventilation, leave a space of at least
10cm all around the set.
Clean the screen and cabinet with a soft,
lightly dampened cloth. Do not use any type
of abrasive pad, alkaline cleaner, scouring
powder or solvent, such as alcohol or
benzine, or antistatic spray. As a safety
precaution, unplug the TV before cleaning it.
Place the TV on a secure stable stand. Never
attempt to move the TV and stand together always move the TV and stand separately.
Do not place the TV on its side or face up. Do
not allow children to climb on to it.
Never place the TV in hot, humid or
excessively dusty places. Do not install the
TV where it may be exposed to mechanical
vibrations.
Pull out the power lead by the plug. Do not
pull on the power lead itself.
Unplug the power lead before moving the
TV. Avoid uneven surfaces, quick steps or
excessive force. If the set has been
dropped or damaged, have it checked
immediately by qualified service personnel.
Do not place any objects on the TV. To
prevent fire, keep inflammable objects or
naked lights (e.g. candles) away from the TV.
Take care not to place heavy objects on the
power lead as this could result in damage.
We recommend you wind any excess lead
around the holders provided on the rear of
the TV.
Do not cover the ventilation openings of the
TV with items such as curtains or
newspapers etc.
Safety Information
5
Getting Started
Follow steps 1 - 6 to install the TV and view programmes
Checking the supplied accessories
1
Check that you have the following items:
SONY CORPORATION JAPAN/4
Remote control
DRY BATTER
Batteries
Y R6/3(NS) SIZE"AA
" 1.5v
RF lead
YUV Scart Adaptor (2)
Inserting batteries into the remote control
2
6 Getting Started
S
O
N
Y
C
O
R
P
O
R
A
T
I
O
N
J
A
P
A
N
/4
SONY CORPORATION JAPAN/4
• Please observe the correct polarity when inserting batteries,
• Remember to dispose of batteries in an environmentally friendly way.
• Do not use old and new batteries together.
• Do not use different types of batteries together.
• To avoid battery leakage and damage to the remote control, rem ov e the b atteries if
you are not goi ng to use the remote contro l f o r se v e ral days. If any liquid that leak s
from the batteries touches you, immediately wash it away with water.
3
Rear of TV.
Connecting an aerial and VCR
Supplied
YUV
Scart Adaptor
Rear of VCR
Connecting a VCR
Connect your aerial lead to the socket labelled
1.
DIGITAL on the rear of the TV.
Connect the supplied RF lead from the socket
2.
labelled on the rear of the TV to the socket
labelled IN* on your VCR.
Connect an RF lead from the sock et labe lled O UT*
3.
on your VCR to the socket label led
the rear of the TV.
Connect an Audio/Video lead from the Video and
4.
audio sockets on your VCR to one of the supplied
YUV Scart Adaptors. Connect the YUV Scart
Adaptor to the scart sock et labelle d i2/r on the
rear of the TV.
Insert a pre-recorded tape into the VCR and press
5.
the ‘PLAY’ button. This enables the TV to locate
and store the video channel during the
‘Automatically tuning the TV’ procedure.
Getting Started
ANALOGUE on
Audio/Video lead
(Not supplied)
Rear of TV.
Supplied RF lead
z *Socket names may vary depending on make and model
of VCR. Refer to your VCR instruction manual for details.
Connecting an aerial only
Connect your aerial lead to the socket labelled
1.
DIGITAL on the rear of the TV.
Connect the supplied RF lead from the sockets
2.
labelled and
ANALOGUE on the rear of the TV.
Supplied RF lead
Getting Started
7
Getting Started
Switching on the TV
4
Automatically tuning the TV
5
The ‘Picture Rotation’ me nu.
If picture slants, please
adjust picture rotation
Not necessary
Adjust now
On/Off button
OK
Connect the TV plug to your mains socket (220 - 240V AV, 50Hz)
1.
Push in the On/Off button (labelled !) on the front of the TV.
2.
z If the red standby mode indicator on the front of the T V is lit, press the TV I/1
button on the remote control to switch on the set. Please be patient as the picture
may take a few moments to appear on the TV screen.
When you switch on the TV for the first time a menu appears on the
1.
screen asking you to check if the picture is slanted. (Sometimes the
Earth’s natural magnetism can cause the screen to look slanted.)
a) If no correction is required, press the V or v button to highlight ‘Not
necessary’. Press the OK button to continue.
b) If some correction is required, press the V or v button to highlight
‘Adjust now’. Press the OK button to continue. Press the V or v button
to correct the slant. Press the OK button to store.
The autotune prompt appears. Press the OK button to select ‘Yes’. The
2.
autotune procedure begins.
The ‘Region Set-up’ menu appears on the TV screen. Press the V or v
3.
button to highlight your chosen region. Press the OK button to confirm.
The ‘Autotune’ prompt.
Do you want to start
automatic tuning?
Yes
No
Switching between digital and analogue mode
6
OK
The digital autotune display appears on screen and the TV starts to
search for all the av ailable digital channels. This may take some time,
please be patient and do not press any buttons on the TV or remote
control.
If no digital or analogue channels are found, a message appears asking
you to confirm that the aerial is connected correctly. Check all the aerial
connections and press the OK button to start the au totune procedure
again.
When the digital autotune is complete, the analogue autotune starts to
search for all the available analogue channels.
Once all available digital and analogue channels have been stored, the
TV returns to normal operation, displaying the first available digital
channel (usually stored on channel number 1). If no digital channels are
found, the TV displays the first available analogue channel (usually
stored on channel 1).
The TV has now tuned
in all the available channels
Press the DIGITAL/a button to switch between digital and analogue
1.
mode.
In digital mode, an information banner appears briefly on screen when
the channel is changed.
8 Getting Started
In analogue mode, the chann el numbe r appears i n green le ttering when
the channel is changed.
Overview of the remote control
VIDEO I/1 - VCR/DVD Standby button
1
1
2
3
4
5
6
7 8
9
q;
qs
qf
qa
qd
qg
qh
qj qk
ql
Press to switch off your VCR/DVD player temporarily. Press again to return to
normal operation.
TV I/1 - TV Standby button
2
Press to switch off the TV temporarily. The red standby indicator on the front of
the TV is lit. Press again to return to normal operation.
3
4
5
6
7
8
9
q;
qa
qs
qd
qf
qg
qh
qj
qk
ql
- Screen Mode button
Press to change the screen mode. Refer to page12.
DIGITAL/a - Digital/Analogue mode, TV button
In TV mode: Press to switch between digital and analogue mode.
In teletext mode, video input mode, TV menu system, INFO menu, EPG and
Channel Index menu: Press to return to normal TV operation.
t/ - Input Select/Teletext Hold button
In TV mode: Press to vie w s ignal s from e qui pment c onnec ted to the TV sockets .
Refer to page 28.
In teletext mode: Press to hold the current page. Refer to page 14.
Numbered buttons
In TV mode: Press to s elect the required c hannel nu mber. Wh en selec ting trebl e
digit numbers, enter the second and third digits within two seconds.
In teletext mode: Press to ent er the three digit al page numb er. Refer to page14.
/ - INFO/Teletext Reveal button
In digital TV mode: Press to access the Info menu. Refer to page 18.
In analogue TV mode: Press to display information such as current channel
number and screen mode.
In teletext mode: Press to revea l con cealed in formati on (e.g . answers to a qu iz).
Refer to page 14.
- Previous channel button
In TV mode: Press to return to the previous channel watched (provided that the
channel was watched for more than five seconds).
In digital TV mode: Press to remov e any in teractive prompts from the TV sc reen.
Coloured buttons
In digital menu systems: Press to select the options at the bottom of the screen
in the Info, Main, Channel Index and EPG digital menus.
In teletext mode: Press to use Fastext. Refer to page 14.
- EPG button
In digital TV mode: Press to access the Digital Electronic Programme Guide
(EPG). Refer to page 16.
/ - Teletext button
In TV mode: Press to access teletext. Refer to page 14.
V, v, B and b buttons
In TV menu system: Press to move through the options. Refer to page21.
OK button
In TV menu system: Press to confirm a selection. Refer to page 21.
In digital TV mode: Press to access the Channel Index menu. Refer to page 15.
In analogue TV mode: Pres s to access the Programme Index table. Press the V
or v button to highlight an analogue channel. Press the b button to display the
chosen channel.
MENU button
Press to access the TV menu system. Refer to page 21.
•REC button
When Mode Selector button is set to ‘VCR’: Press to begin recording. Refer to
page 29.
Mode Selector button
This remote control can be programmed to operate the basic functions of most
DVD players and VCRs. Once programmed, press this button repeatedly to
select TV, VCR or DVD mode. Refer to page 29.
2 +/- Volume buttons
Press to increase (+) or decrease (-) the TV volume.
PROG +/- buttons
In TV mode: Press to view the next (+) or previous (-) channel.
In teletext mode: Press to view the next (+) or previous (-) page. Refer to
page 14.
% - Mute button
Press to mute the TV sound. Press again to restore.
Basic Operation
Basic Operation
9
Basic Operation
Overview of the TV buttons
o4
3 3
Press gently on th e symbol to open t he do or.
1 2 3 4 5
3 3
o3
1
2
3
- Autotune button
Press to repeat the automatic tuning process.
t - Video Input button
Press to view pictures from equipment connected to the TV sockets.
2 +/- buttons
Press to increase (+) or decrease (-) the TV volume.
10 Basic Operation
PROG +/- buttons
4
In TV mode: Press to view the next (+) or previous (-) channel.
! - On/Off button
5
Press to switch the TV on or off.
Basic Operation
Everyday use
o4
3 3
2 +/-
t
buttons
button
On/Off
button
PROG +/-
buttons
This section explains the various functions and operations used during everyday
viewing. Most operations can be done us ing the remote control.
Press the On/Off button (labelled !) on the front of the TV to switc h
1.
on the TV.
When the TV is in standby mode (the 1 indicator on the TV is lit red),
press the TV I/1 button on the remote control to switch on the TV.
Press the PROG+/- buttons on the TV or press the PROG+/- or
2.
Numbered buttons on the remote control to select a TV channel.
When selecting trebl e di git n um bers usi ng the Numbered buttons, enter
the second and third digits within two seconds.
Press the 2 +/- buttons on th e TV or on the remote control to adjust the
3.
volume.
Additional operations
To Press
Turn off the TV temporarily
(standby)...
Mute the sound... % button on the remote control. Press
TV I/1 on the remote control. When
the TV is in standby mode the 1
indicator on the TV is lit red. Press
again to return to normal TV operation.
again to cancel.
DIGITAL/a button
button
TV I/1
button
t/
button
Numbered
buttons
button
/
button
2 +/-
buttons
PROG +/-
buttons
Switch between analogue and digital
mode...
DIGITAL/a button.
If the TV is in digital mode an
information banner ap pea rs b riefly on
screen when you change channels.
If the TV is in analogue mode the
channel number appears in green
lettering when you change channels.
Change the Screen Mode... button. Refer to page 12.
Watch pictures from equipment
connected to the TV’s front and rear
sockets (video input mode)...
t button on the TV or t/ button
on the remote control repeatedly until
the picture appears. Refe r to pag e 28 .
z For example, if you wish to view pictures from a DVD player connected to the
i1/ socket on the rear of the TV , press the
t1 symbol appears on the TV screen together with the DVD picture.
Please note, most equipment connected by scart lead, when activated, will send
a signal to the TV. The TV will automatically display the picture for you.
Access teletext services (depending
on availability of service)...
/ button on the remote control.
Refer to page 14.
Access the Digital Electronic
Programme Guide (EPG)...
Return to normal TV operation (from
Refer to page 16.
DIGITAL/a button.
teletext, video input mode, TV menu
system, INFO menu, EPG and
Channel Index menu). ..
t/ button repeatedly until the
button on the remote co ntrol.
% button
Basic Operation
11
Loading...