Sony VPL-VW285ES User Manual

Video Projector

4-725-444-01 (1)

Operating Instructions

Before operating the unit, please read this manual and supplied Quick Reference Manual thoroughly and retain them for future reference.

VPL-VW285ES

Table of Contents

Location of Controls

Front/Right Side ................................ 3

Rear/Left Side/Bottom ...................... 4

Remote Control ................................. 5

Connections and Preparations

Installing the Unit .............................. 6

Adjusting the Picture Position ........... 7

Connecting to Video Equipment or a

Computer ...................................... 11

Projecting

Projecting the Picture ...................... 13

Turning Off the Power ............... 13

Watching 3D Video Images ............. 14

Using the 3D Glasses ................. 14

Selecting the Aspect Ratio According to

the Video Signal ........................... 16

Selecting the Picture Viewing

Mode ............................................ 19

Using the Menus

Operation through the Menus .......... 20

Picture Menu ................................... 22

Screen Menu .................................... 27

Setup Menu ...................................... 29

Function Menu ................................ 31

Items Locked by Settings

Lock ........................................ 33

Installation Menu ............................. 34

Information Menu ............................ 37

About the Preset Memory .......... 37

Using Network Features

Displaying the Control Window of the

Unit with a Web Browser .............38

Operating the Control Window ........39

Switching the Page .....................39

Setting the Access Limitation ....39

Confirming the Information

Regarding the Unit .................. 40

Error Handling

Troubleshooting ...............................41

Warning Indicators ...........................44

Message Lists ...................................45

Others

Updating the Software .....................46

About HDR (high dynamic range) ...46

About the simulated 3D feature ....... 46

NOTICES AND LICENSES FOR

SOFTWARE USED IN THIS

PRODUCT .................................... 46

Replacing the Lamp .........................47

Cleaning ........................................... 50

Specifications ................................... 51

Preset Signals ............................. 52

Input Signals and Adjustable/

Setting Items ........................... 54

Compatible 3D Signals ...............55

3D Signals and Adjustable/Setting

Items ........................................ 55

Aspect Mode .............................. 57

Motionflow ................................. 58

Storage Conditions of Adjustable/

Setting Items ........................... 58

Projection Distance and Lens Shift

Range ............................................ 60

Dimensions ...................................... 64

Index .................................................68

Location of Controls

Front/Right Side

Warning indicators

a ON/STANDBY indicator

(page 44)

b WARNING indicator (page 44)

Connectors

c LAN connector (page 38)

d USB connector (page 46)

e HDMI 1/HDMI 2 connector

(page 11)

f REMOTE connector

Connects to a computer, etc. for remote control.

g IR IN connector

Inputs signals to control the unit.

h TRIGGER 1/TRIGGER 2

connector (page 34)

Others

i Lamp cover (page 47)

j Ventilation holes (exhaust)

k Ventilation holes (intake)

(page 49)

l Remote control detector

(page 7)

Rear/Left Side/Bottom

The buttons on the control panel have the same names as those on the remote control.

Control panel

a ?/1 (ON/STANDBY) button

(page 7)

b INPUT button (page 13)

c MENU button (page 20)

d M/m/</, (arrow)/ (enter)

button (page 20)

e LENS button (page 7)

Others

f Remote control detector

(page 7)

g Ventilation holes (intake)

(page 49)

h AC IN socket (page 7)

i Projector suspension support

attaching hole (page 65)

j Front feet (adjustable) (page 10)

Remote Control

a LIGHT button

Illuminates the buttons on the remote control.

b Infrared transmitter

c ?/1 (ON/STANDBY) button

(page 7)

d INPUT button (page 13)

e CALIBRATED PRESET buttons

(page 19)

f PATTERN button (page 8)

g RESET button (page 21)

h M/m/</, (arrow)/ (enter)

buttons (page 20)

i MENU button (page 20)

j MOTIONFLOW button (page 23)

k ASPECT button (page 16)

l COLOR SPACE button (page 26)

m COLOR TEMP button (page 24)

n GAMMA CORRECTION button

(page 25)

o 3D button (page 14)

p COLOR CORRECTION button

(page 25)

q REALITY CREATION button

(page 23)

r CONTRAST ENHANCER button

(page 23)

s SHARPNESS +/– button

(page 24)

t CONTRAST +/– button (page 23)

u BRIGHTNESS +/– button

(page 24)

Connections and Preparations

Installing the Unit

The installation distance between the unit and a screen varies depending on the size of the screen or whether or not you use the lens shift features. Install this unit so that it fits the size of your screen. For details on the distance between the unit and the screen (the projection distance) and the size of projected video, see “Projection Distance and Lens Shift Range” (page 60).

1 Position the unit so that the lens is

parallel to the screen.

Top view

Screen

Note

When using a screen with an uneven surface, stripes pattern may rarely appear on the screen depending on the distance between the screen and the unit or the zooming magnifications. This is not a malfunction of the unit.

2 Project an image on the screen and

adjust the picture so that it fits the screen (page 7).

Adjusting the Picture Position

Project an image on the screen and then adjust the picture position.

Note

Depending on the installation location of the unit, you may not be able to control it with the remote control. In this case, point the remote control at the remote control detector of the unit or the screen.

1 After connecting the AC power cord to

the unit, plug the AC power cord into a wall outlet.

The ON/STANDBY indicator lights in red and the unit goes into standby mode.

Remote control detector

Tips

?/1 (ON/STANDBY), INPUT, MENU,

• The

and M/m/</,/ (joystick) buttons on the side panel of the unit function the same as those on the remote control. The LENS button functions in the same way as the PATTERN button of the remote control.

• When adjusting the lens, each time you press the LENS button on the unit, the lens adjustment function switches between “Lens Focus,” “Lens Zoom” and “Lens Shift.”

Lights in red.

2 Press the ?/1 (ON/STANDBY) button

to turn on the unit.

The ON/STANDBY indicator flashes in green, and then lights in green.

Flashes in green for tens of seconds and then lights in green.

3 Adjust the focus.

Press the PATTERN button repeatedly to display the Lens Focus adjustment window (test pattern). Then adjust the focus of the picture by pressing the M/m/ </, buttons.

Tips

• When “Lens Control” is set to “Off” on the Installation menu, you cannot adjust the lens (FOCUS, ZOOM, or SHIFT) (page 34).

• When “Test Pattern” is set to “Off” on the Function menu, the test pattern is not displayed (page 32).

Note

Adjust the lens by using buttons on the remote control or the control panel of the unit. Never make adjustments by directly turning the lens with your hands, which may cause damage or malfunction to the unit.

4 Adjust the picture size.

Press the PATTERN button repeatedly to display the Lens Zoom adjustment window (test pattern). Then adjust the size of the picture by pressing the M/m/ </, buttons.

To make the picture larger, press M/,. To make the picture smaller, press m/ <.

5 Adjust the picture position.

Press the PATTERN button repeatedly to display the Lens Shift adjustment window (test pattern). Then adjust to the proper position of the picture by pressing the M/m/</, buttons.

Tip

Whenever you press the button, the test pattern disappears.

Note

When adjusting the window position, do not touch the lens unit, otherwise your fingers may be pinched by the moving parts.

To adjust the horizontal position

To adjust the vertical position

Press </,.

The picture projected on the screen moves right or left by a maximum of 31% of the screen width from the center of the lens.

Top view

31% 31%1 screen width

: Picture position when moving the

picture to the left at maximum

: Picture position when moving the

picture to the right at maximum

Press M/m.

The picture projected on the screen moves up by a maximum of 85% or moves down by a maximum of 80% of the screen height from the center of the lens.

Side view

85%

1 screen height

80%

: Picture position when moving the

picture upward at maximum

: Picture position when moving the

picture downward at maximum

Note

The range to move the picture projected on the screen can be adjusted only within the octagon area illustrated below. For details, see “Projection Distance and Lens Shift Range” (page 60).

Range of movement of the projected picture

0.85V

0.31H Projected Picture

0.31H

Lens adjustment window (test pattern)

1.78:1 (16:9)

1.33:1 (4:3)

0.8V

H: Width of the projected picture V: Height of the projected picture

To adjust the tilt of the installation surface

If the unit is installed on an uneven surface, use the front feet (adjustable) to keep the unit level.

2.35:1

1.85:1

The dashed lines show the screen sizes of each aspect ratio.

Turn to

Front feet (adjustable)

Notes

adjust.

• If the unit is tilted up or down, the projected image may be trapezoidal.

• Be careful not to catch your finger when turning the front feet (adjustable).

Connecting to Video Equipment or a Computer

You can enjoy high picture quality by connecting a DVD player/recorder, Blu-ray Disc player/ recorder, or PlayStation

equipped with HDMI output to the HDMI input of the unit.

When making connections, be sure to do the following:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor picture quality. When pulling out a cable, be sure to pull it out from the plug, not the cable itself.

• Refer to the operating instructions of the connected equipment.

Computer

Right side of the unit

Equipment with HDMI output connectors

AV amplifier

Speakers

to HDMI output

HDMI cable (not supplied)

: Video signal flow Use a High Speed HDMI cable or a Premium High Speed

HDMI cable on which the cable type logo is specified.

Notes

• Use a High Speed HDMI cable or a Premium High Speed HDMI cable. With a standard HDMI cable, images of 1080p, DeepColor, 3D video and 4K video may not be displayed properly.

• When connecting an HDMI cable to the unit, make sure the

V mark on the upper part of the HDMI

input of the unit and the v mark on the connector of the cable is set at the same position.

• If the picture from equipment connected to the unit with an HDMI cable is not correct, check the settings of the connected equipment.

• If you set your computer, such as a notebook type, to output the signal to both computer’s display and this equipment, the picture of the equipment may not appear properly. Set your computer to output the signal to only the external monitor. For details, refer to the computer’s operating instructions supplied with your computer. For settings of the computer, consult with the manufacturer of the computer.

Projecting

Projecting the Picture

1 Turn on both the unit and the

equipment connected to the unit.

2 Press INPUT to display the input

palette on the screen.

3 Select the equipment from which you

want to display images.

Press INPUT repeatedly or press M/m/

(enter) to select the equipment from

which to project.

The fan stops and the ON/STANDBY indicator changes from flashing green to remaining red.

The power is turned off completely, and you can disconnect the AC power cord.

Note

Never disconnect the AC power cord while the indicator is flashing.

Tip

You can turn off the unit by holding the ?/1 (ON/STANDBY) button for about 1 second, instead of performing the above steps.

Example: To view the picture from the video equipment connected to the HDMI 1 connector of this unit.

Tip

When “Status” is set to “Off” on the Setup menu, the input palette does not appear. Press the INPUT button to switch between input terminals in sequence.

Turning Off the Power

1 Press the ?/1 (ON/STANDBY)

button.

A message “POWER OFF?” appears on the screen.

2 Press the ?/1 (ON/STANDBY) button

again before the message disappears.

The ON/STANDBY indicator flashes in green and the fan continues to run to reduce the internal heat.

Watching 3D Video Images

You can enjoy powerful 3D video images, such as from 3D games and 3D Blu-ray Discs, using the optional Active 3D Glasses (TDG-BT500A).

Adjusting/Setting the 3D functions

You can adjust/set the 3D functions by pressing the 3D button on the remote control or with the “3D Settings” of the Function menu. For details, see “3D Settings” (page 31).

Using the 3D Glasses

1 Turn on the HDMI equipment for 3D

compatibility connected to the unit, then play the 3D content.

For details on how to play 3D content, refer to the operating instructions for the connected equipment.

2 Turn on the unit and project the 3D

video image onto the screen.

For details on how to project the image, see “Projecting the Picture” (page 13).

3 Turn on the 3D glasses, and then put

them on so that they fit comfortably.

For details on how to use the 3D glasses, see “Using the 3D Glasses” (page 14).

Tips

• The factory default setting for ”2D-3D Display Sel.” is “Auto” to allow projecting 3D video images automatically when the unit detects 3D signals.

• To convert 3D video images to 2D video images, set “2D-3D Display Sel.” to “2D” (page 31).

Notes

• It may not be possible to display 3D video image, depending on the type of signal. Set the “2D-3D Display Sel.” to “3D,” and “3D Format” to “Side-by-Side” or “Over-Under” to suit the format of the 3D content you want to watch (page 31).

• Use the 3D glasses within the communication range (page 14).

• There are differences in perception of 3D video images among individuals.

• When the temperature of the usage environment is low, the 3D effect may be diminished.

1 Turn on the 3D glasses, and register

them on the unit.

For details on how to register the 3D glasses, refer to the operating instructions supplied with the 3D glasses.

2 Put on the 3D glasses.

3 Turn toward the screen.

Precautions for use

Misoperation may occur if:

• The viewing position is too far from the projector

• There are other communication devices, such as a wireless LAN (IEEE802.11 b/g/ n) or a microwave with a bandwidth of 2.4 GHz, near the unit

3D glasses communication range

Figure below indicate the communication range of the 3D glasses. If you try to watch 3D video images from a distance greater than the communication range or install the unit outside the communication range, the 3D glasses may not be able to display the images properly. Also, the distance varies depending on the environment of the room and installation environment of the unit.

Top or side view

10 m

Projector

10 m 10 m

Selecting the Aspect Ratio According to the Video Signal

You can select an aspect ratio best suited for the video signal received.

Press ASPECT.

Each time you press the button, you can select the “Aspect” setting.You can also select it using the menu (page 28).

Original image Recommended setting and resultant images

1.85:1

Squeezed 1.85:1

ASPECT button

1.85:1 Zoom

2.35:1 Zoom

2.35:1

Squeezed 2.35:1

Original image Recommended setting and resultant images

Normal

1.78:1 (16:9)

1.33:1 (4:3)

1.33:1 (4:3) with side panels

V Stretch

2.35:1

16:9

When using an anamorphic lens

Squeeze

When using an anamorphic lens

Original image Recommended setting and resultant images

Stretch

Squeezed

Notes

• Selectable aspect modes vary depending on the input signal (page 57).

• The aspect cannot be selected for an input signal from a computer, or an input signal with a resolution of 4096 × 2160 (page 52).

Notes on switching the “Aspect” setting

• Select the aspect mode taking into account that changing the aspect ratio of the original picture will provide a different look from that of the original image.

• Note that if the unit is used for profit or for public viewing, modifying the original picture by switching the aspect may constitute an infringement of the rights of authors or producers, which are legally protected.

Selecting the Picture Viewing Mode

You can select the picture viewing mode that best suits the type of video source or room conditions. You can save and use different preset modes for 2D/3D respectively.

Press one of the CALIBRATED PRESET buttons.

Setting items Description

CINEMA FILM 1 Picture quality suited to reproducing the highly dynamic and

clear images typical of master positive film.

CINEMA FILM 2 Picture quality suited to reproducing the rich tone and color

typical of a movie theater, based on the Cinema Film 1.

REF A picture quality setup suitable for when you want to reproduce

faithfully the original image quality, or for enjoying image quality, without any adjustment.

TV Picture quality suited for watching TV programs, sports,

concerts, and other video images.

PHOTO Ideal for projecting still images taken with a digital camera.

GAME Picture quality suited to gaming, with well-modulated colors

and fast response.

BRT CINE Picture quality suited for watching movies in a bright

environment, such as a living room.

BRT TV Picture quality suited for watching TV programs, sports,

concerts, and other video images in a bright environment, such as a living room.

USER Adjusts the picture quality to suit your taste then saves the

setting. The factory default setting is the same as “REF.”

CALIBRATED PRESET buttons

Using the Menus

Note

The menu displays used for the explanation may be different from the actual menu display.

3 Press M/m to select an item you want

Operation through the Menus

The unit is equipped with an on-screen menu for making various adjustments and settings. If you select an item name followed by an arrow (B), the next menu window with setting items appears.

1 Press MENU.

The menu window appears.

to set or adjust and press , or .

The setting items are displayed in a popup menu, in a setting menu, in an adjustment menu or in the next menu window.

Pop-up menu

Setting items

Setting menu

2 Press M/m to select a menu item, and

press , or .

The items that can be set or adjusted with the selected menu appear. The item presently selected is shown in white.

Adjustment menu

Next menu window

Setting items

4 Make the setting or adjustment of an

item.

When changing the adjustment level

Press M/, to increase the value, and press m/< to decrease the value. Press to store the setting and restore the original menu screen.

When changing the setting

Press M/m to change the setting. Press to restore the original screen. You can restore the original screen using < depending on the selected item.

To reset the items that have been adjusted

Select an item in the menu screen, and display the pop-up menu, the setting menu, or the adjustment menu. Press RESET on the remote control to reset only the selected settings to its factory preset value.

Note

The RESET button on the remote control is available only when the adjustment menu or the setting menu is selected.

To clear the menu

Press MENU.

To reset the picture that has been adjusted

Select “Reset” from the Picture menu.

When the screen display appears, select “Yes” using < and press . All of the following settings are reset to its factory preset value: “Reality Creation,” “Cinema Black Pro,” “Motionflow,” “Contrast,” “Brightness,” “Color,” “Hue,” “Color Temp.,” “Sharpness,” and “Expert Setting” on the Picture menu

+ 49 hidden pages