Sony VPL-HS51, VPL-HS51A User Manual

Video Projector

Operating Instructi on s

2-188-141-11 (1)

VPL-HS50 VPL-HS51

WARNING

Address: 1645 0 W. Bernardo Dr, San Dieg o, CA 92127 U.S.A. Telephone Number: 858-942-2230

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclo sure that may be of sufficient magnitude to constitute a risk of electric shock to persons .

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

For the customers in the USA

If you have any questions about this product, you may call: Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.co m/ The number below is for FCC related matters only.

Declaration of Conformity

Trade Name: SONY Model No.: VPL-HS50/HS51 Responsible Party: Sony Electronics Inc .

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept an y interference received, including interference that may cause undesi re d operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generat es, uses, and can radiate radio frequency energy and, if not installed and use d in accordance with the instructions, may cause harmful interfe rence to radio communications. However, there is no guarantee that interference will not occ ur in a particular installation. If this equ ipmen t does cause harmful interference to radio or television reception, which can be determined by turning th e equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measure s :

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment an d receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could vo id your authori ty to ope rate this equipment.

This product contains mercury.Disposal of this product may be regulated if sold in the United Stat es . For disposal or r ec ycling information, please contact yo ur loc a l authorities or Electronics Industries Allianc e (www.eiae.org http://www.eiae.org).

For the customers in Canada

This Class B digital apparatus complies with Canadian ICES-003.

Voor de klanten in Nederland

Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA).

The socket-outlet should be installed ne ar the equipment and be easily accessible.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSED OF USED BATTERIES ACCORDING TO THE LOCAL RULES.

Table of Contents

Precautions ......................................... 6

Connections and Preparations

Unpacking ..........................................7

Step 1: Installing the Projector ...........8

Before Setting Up the Projector ...9 Installing the Projector and

a Screen ...........................10

Step 2: Connecting the Projector .....13

Connecting to a DVD Player/

Recorder or Digital

Tuner ............................... 13

Connecting to Video Equipment 15

Connecting to a Computer ..........16

Step 3: Adjusting the Picture Size and

Position .................................. ...... .....17

Step 4: Selecting the Menu

Language .......................................... 21

Projecting

Projecting the Picture on the Screen 23

Turning Off the Power ...............25

Selecting the Wide Screen Mode .....26

Selecting the Picture Viewing Mode 29

Adjusting the Picture Quality ...........30

Adjusting the Picture Using Real Color

Processing ........................................32

Signal Menu .....................................40

Function menu ................................. 41

Installation Menu .............................42

Setup Menu ......................................43

Information Menu ............................ 44

About the Preset Memory No. ... 44

Adjusting Picture Quality of a Signal

from the Computer ..........................45

Others

Troubleshooting ...............................46

Warning Indicators .................... 47

Message Lists ............................. 48

Replacing the Lamp ......................... 49

Replacing the Air Filter ................... 50

Specifications .................................. 52

Input Signals and Adjustable/setting

Items ............................... 54

Preset Signals .............................56

Ceiling Installation .......................... 58

Location of Controls ........................ 61

Front ......................................... 61

Rear ......................................... 62

Bottom ....................................... 63

Remote Control .......................... 64

Index ...............................................65

Using the Menus

Operation through the Menus ..........34

Picture Menu ....................................37

Precautions

On safety

• Check that the operating voltage of your unit is identical with the voltage of your local power supply.

• Should any liquid or solid object fall into the cabinet, unpl ug the unit an d ha v e it checked by qualified personnel before operating it further.

• Unplug the unit from the wall ou tlet if it is not to be used for sev e ral days.

• To disconnect the cord, pull it out by the plug. Never pull the cord itself.

• The wall outlet should be near the unit and easily accessible.

• The unit is not disconnected to the AC power source (mains) as long as it is connected to the wall outlet , even if the unit itself has been turned off.

• Do not lo ok into th e lens while the lamp is on.

• Do not plac e your hand or ob jects near the ventilation holes. The air coming out is hot.

On preventing internal heat buildup

After you turn off the power with the I/1 (on/standby) switch, do not disconnect the unit from the wall outlet while the cooling fan is still running.

Caution

The projector is equipped with ventilation holes (intake) and ventilation holes (exhaust). Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.

On repacking

Save the original s hipping carton and packing material; they will come in h andy if you ever have to ship your unit. For maximum protect ion, repack your unit as it was originally packed at the factory.

6 Precautions

This manual covers models VPL-HS50 and VPL-HS51. The illustrations of the projector used in this manual are those of the VPL-HS50 unless the model name is specifically mentioned.

Connections and Preparations

This section desc r ibe s how to install the pr oj ec tor a n d sc r e en, how to connect the equipment from which you want to project the picture, etc.

Unpacking

Check the carton to make sure it contains the following items:

Connections and Pre pa ra tions

• Remo te control (1)

• Size AA (R6) batteries (2)

• AC power cord (1 )

• CD-ROM (Applicatio n software and Operating In structions) (V P L-HS51 only)

• Air filter (for replacement) (1)

• Operating Instructions (this manual) (1)

Inserting the batteries into the remote control

Insert the batteries E side first as shown in the illustration. Inserting them forcibly or with t he polarit ies rev ers ed may caus e a short circuit and may generate heat.

7Unpacking

Step 1: Installing the Projector

The projector’s lens shift feature allows you to choose a variety of installation locations for your projector. You can enjoy home entertainment with this projector in the following situations.

Enjoying home theater

Watching sports, etc. with your company

Enjoying video games on a large screen

Viewing images shot by a digital video camera on a large screen

8 Step 1: Installing the Projector

Before Setting Up the Projector

Do not place the projector in the following situations, which may cause malfunction or damage to the projector.

Poorly ventilated

Very dusty and extremely smoky

Connections and Pre pa ra tions

Make a special attention to the following while using the projector.

Do not block the ventilation holes.

Highly heated and humid

Subject to direct cool or warm air from an air-conditioner

Installing in such a location may cause malfunction of the unit due to moisture condensation or r is e in te mp e rature.

Near a heat or smoke sensor

Ventilation holes (intake)

Ventilation holes (exhaust)

Tip

For details on the location of the ventila tion holes (intake or exhaust), see “Location o f Controls” on pages61 to 63.

When installing the unit at altitudes

When using the projector at an altitude of 1,500 m or higher, set “High Altitude Mode” in the Installation menu to “On.” (1 page 42) Failing to set this mode when using the projector at high altitudes could have adverse effects, such a s r educing the relia bility of certain components.

Malfunction of the sensor may be caused.

9Step 1: Installing the Projector

Installing the Projector and a Screen

The installation distance between the projector and a screen varies depending on the size of the screen.

1 Determine the installation position of the projector and screen.

You can obtain a good quality picture if you position the projector with the center of the lens within the areas indicated in the gray areas in the illustration. Use the values a, b, c, d and e in the table on page 11 as a g uide.

Screen

a: Minimum projection distance between the screen and the center of the

projector’s l ens

b: Maximum projection distance between the screen and the center of the

projector’s l ens

c: Vertical distance between the center of the screen and the center of the

projector’s lens when using the maximum vertical lens shift feature*

d: Horizontal distance between the center of the screen and the center of

the projector’s lens when using the maximum horizontal lens shift feature*

e: Maximum vertical distance between the center of the screen and the

center of the projector’s lens when using both the vertical and horizontal lens shift features with the horizontal lens shift set to the maximum value*

* The distances c, d and e indicated in the illustration show those in the lower

or left direction. The same distances i n t he upper or right direction are appropriate fo r i n stallation.

For details on the lens shift feature, see “Step 3: Adjusting the Picture Size and Position.” (1 page 17)

10 Step 1: Installing the Projector

When using the 16:9 aspect ratio screen

Screen size (inches)

a (minimum) 1170

b (maximum) 1790

c 498

d 443

e 249

40 60 80 100 120 150 180 200

1770

(46

/8)

(69 3/4) 2710

/2)

(70

(19

(17

To calculate the installation measurements (SS: Screen Size) a (minimum) = {(SS × 21.27/0.7227) – 35.160899} × 1.025 b (maximum) = {(SS × 33.9409273/0.7227) – 37.678872} × 0.975 c = (SS/0.7227 × 9) d = (SS/0.7227 × 8) e = (SS/0.7227 × 4.5)

(106 3/4) 747

/8)

(29 1/2) 664

/2)

(26 1/4) 374

/8)

(14 3/4)

When using the 4:3 aspect ratio screen

Screen size (inches)

a (minimum) 1440

b (maximum) 2200

c610

d542

e305

40 60 80 100 120 150 180 200

2180

(56

/4)

(85 7/8) 3330

/8)

(86

(24

(21

(12

(131 1/8) 914

/8)

(36) 813

/8)

(32 1/8) 457

/8)

(18)

2380 (93 3/4)

3630 (143)

996 (39 1/4)

886 (35)

498 (19 5/8)

2920 (115)

4450 (175 1/4)

1219 (48)

1084 (42 3/4)

610 (24 1/8)

2980 (117 3/8)

4540 (178 7/8)

1245 (49 1/8)

1107 (43 5/8)

623 (24 5/8)

3660 (114 1/8)

5570 (219 3/8)

1524 (60)

1355 (53 3/8)

762 (30)

3580 (141)

5460 (215)

1494 (58 7/8)

1328 (52 3/8)

747 (29 1/2)

4390 (172 7/8)

6690 (263 1/2)

1829 (72 1/8)

1626 (64 1/8)

914 (36)

4490 (176 7/8)

6830 (269)

1868 (73 5/8)

1660 (65 3/8)

934 (36 7/8)

5500 (216 5/8)

8370 (329 5/8)

2286 (90 1/8)

2032 (80 1/16)

1143 (45)

Unit: mm (inches)

5390 (212 1/4)

8210 (323 3/8)

2241 (88 1/4)

1992 (78 1/2)

1121 (44 1/4)

Unit: mm (inches)

6610 (260 3/8)

10050 (395 3/4)

2743 (108 1/8)

2438 (96)

1372 (54 1/8)

6000 (236 1/4)

9120 (359 1/8)

2491 (98 1/8)

2214 (87 1/4)

1245 (49 1/8)

7350 (289 1/2)

11170 (439 7/8)

3048 (120

2709 (106 3/4)

1524 (60)

Connections and Pre pa ra tions

/16)

To calculate the installation measurements (SS: Screen Size) a (minimum) = {(SS × 21.27/0.5906) – 35.160899} × 1.025 b (maximum) = {(SS × 33.9409273/0.5906) – 37.678872} × 0.975 c = (SS/0.5906 × 9) d = (SS/0.5906 × 8) e = (SS/0.5906 × 4.5)

11Step 1: Installing the Projector

2 Position the projector so that the lens is parallel to the screen.

Top view

Screen

3 Project an image on the screen and adjust the picture so that it

fits the screen. (1 page 17)

To project an image, connect video equipment to the projector. (1 page

13)

Note

When using a screen with an uneven surface, stripes pattern may rarely appear on the screen dependin g on the distance between the screen and the pro je ctor or the zooming magnifications. This is not a malfunction of the projector.

For installation of the projector on a ceiling, see “Ceiling Installation.” (1 page 58)

12 Step 1: Installing the Projector

Step 2: Connecting the Projector

When making connections, be sure to do the following:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the cable plugs properly; plugs that are not fully inserted often generate noise. When pulling out a cable, be sure to pull it out from the plug, not the cable itself.

• Refer to the operating instructions of the connected equipment.

Connecting to a D VD Player/Recorder or Digital Tune r

To connect to a DVD player/recorder or digital tuner equipped with component video connectors

Connections and Pre pa ra tions

AV amplifier

Rear of the projector

DVD player/recorder, digital tune r , etc., with component video connectors

PB/CB PR/CR VIDEOHDMI

PB/

: Video signal flow

PR/C

Component video cable (not supplied)

INPUT

S VIDEO

PB/ C

Tip

To connect the projector to a DVD player/recorder, digital tuner, etc. which is not equipped with component video connectors, use the S video cable to connect to the Svideo output of the DVD player/r ecord er, dig ital t uner, e tc. I f the c onnected e quipment is not equipped with the S-video output connector, use the video cable to connect to the video output jack on t he equipment.

Speakers

PR/C

13Step 2: Connecting the Projector

To connect to a DVD player/recorder equipped with HDMI output

You can enjoy better picture quality by connecting a DVD player/recorder equipped with HDMI output to the HDMI input of the projector.

Rear of the projector

: Video signal flow

AV amplifier

DVD player/recorder, etc., with the HDMI output

Y PB/CB PR/CR VIDEOHDMI

INPUT

to HDMI output

HDMI cable ( not supplied)

Speakers

............................................................................................................................................................

HDMI, HDMI logo and High-Definition Multimedia Interface are tra demar ks or regis tered trademarks of HDMI Li censing LLC.

14 Step 2: Connecting the Projector

Connecting to Video Equipment

You can connect a DVD player/recorder which is not equipped with component video connectors, hard disk video recorder, VCR or laser disk player. See also the instruction manual of each equipment.

Rear of the projector

PR/CR VIDEO

INPUT

S VIDEO

INPUT A

Speakers

Video equipment

to S video or video output

Connections and Pre pa ra tions

AV amplifier

: Video signal flow

S video or video cable (not supplied)

Tip

If you do not know to which connector you should connect the cable, S VIDEO (S video connector) or VIDEO (video connector), connect it to S VIDEO to enjoy better picture quality. If the equipment to be connected has no S video connector, connect the cable to the video output.

15Step 2: Connecting the Projector

Connecting to a Compute r

Rear of the projector

Computer

PR/CR VIDEO

: Video signal flow

INPUT

S VIDEO

INPUT A

to monitor output

HD D-sub 15-pin cable (not supplied)

Tip

Set “Input A Signal Sel.” in the Setup menu to “Auto” or “Computer.” If the input signal does not appear properly, set it to “C om puter.”

Note

If you set your computer, such as a notebook type, to output the s ig nal to both your computer’s display and an external moni tor, the picture of the e xternal monitor may not appear properly. Set your computer to output the signal to only the external monitor. For details, refer to the computer’s operating in structions supplied with y o ur c omp ut er.

16 Step 2: Connecting the Projector

Step 3: Adjusting the Picture Size and

Position

Project an image on the screen and then adjust the picture position.

VPL-HS50

ON/STANDBY indicator

Adjusters

Remote control detector

Connections and Pre pa ra tions

VPL-HS51

DYNAMIC

INPUTLIGHT

STANDARD

PICTURE MODE

USER 2

ENTER

CINEMA

USER 3USER 1

ON/STANDBY indicator

Adjusters

Remote control detector

Tip

The I/1 (on/standby), INPUT, MENU, and M/m/</,/ENTER (joystick) but tons on the side panel of the pr oj ector function the same as those on the remot e control.

Note

Depending on the installatio n location of the projector, you may not control it with the remote control. In this case, point the remote control to the screen instead of the projector.

1 Plug the AC power cord into a wall outlet.

The ON/STANDBY indicator lights in red and the projector goes into standby mode.

Lights in red.

ON/

STANDB

17Step 3: Adjusting the Picture Size and Position

2 Press the I/1 (on/standby) switch to turn on the projector.

The ON/STANDBY indicator lights in green.

Lights in green.

ON/

STANDB

3 Turn on the equipment connected to the projector.

Refer to the operating instructions of the connected equipment.

4 Press INPUT to project the picture on the screen.

Each time you press the button, the input indication changes. (1 page 24)

INPUT

Tip

When “Auto Input Search” is set to “On” in the Function menu, the channel of the signal input is automatically displayed.

Video

5 Move both LENS SHIFT dials to adjust the picture position.

LENS SHIFT

To adjust the vertical position

To adjust the horizontal position

18 Step 3: Adjusting the Picture Size and Position

To adjust the horizontal position

Turn the LENS SHIFT dial right or left. The picture moves right or left by a maximum of half of the screen size from the center of the lens.

/2H

Top view

: Picture position when moving the

picture to the left at maximum

: Picture position when moving the

picture to the right at maximum

To adjust the vertical position

Turn the LENS SHIFT dial up or down. The picture moves up or down by a maximum of the screen size from the center of the lens.

Connections and Pre pa ra tions

Side view

: Picture position when moving the

picture upward at maximum

: Picture position when moving the

picture downward at maximum

19Step 3: Adjusting the Picture Size and Position

Note

When you use the horizontal and vertical lens shift features at the same time, you can move the pictu re vertically by a maxi m um of half of the scre en size.

6 Adjust the picture size using the zoom ring.

Zoom ring

7 Adjust the focus using the focus ring.

Focus ring

To adjust the tilt of the installation surface

If the projector is installed on an uneven surface, use the adjusters to keep the projector level.

20 Step 3: Adjusting the Picture Size and Position

Turn to adjust.

Adjusters

Step 4: Selecting the Menu Language

You can select one of fifteen languages for displaying the menu and other onscreen displays. The factory default setting is English.

Connections and Pre pa ra tions

DYNAMIC

PICTURE MODE

WIDE MODE

REAL COLOR PROCESSING

INPUTLIGHT

STANDARD

USER 2

ENTER

ADJ PIC

RCP

CINEMA

USER 3USER 1

MENUAPA

RESET

4-6

Tip

You can operate the menu using the M/m/</, (arrow) buttons on the side panel of the projector inst ead of the M/m/</,/ENTER buttons on the remote control.

1 Plug the AC power cord into a wall outlet.

The ON/STANDBY indicator lights in red and the projector goes into standby mode.

2 Press the I/1 (on/standby) switch to turn on the projector.

The ON/STANDBY indicator lights in green.

3 Press MENU.

The menu appears.

Cinema

Off

Picture

Signal

Function

Installation

Setup

Information

Picture Mode : Adjust Picture RCP :

Sel : Set : Back : Exit :

21Step 4: Selecting the Menu Language

+ 47 hidden pages