Sony VPL-CS5A Service Manual

DATA PROJECTOR

VPL-CS5A VPL-CS6 VPL-CX6 VPL-EX1

REMOTE CONTROLLER

RM-PJ2 RM-PJM12

SERVICE MANUAL 1st Edition

! W ARNING

This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.

! W ARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen.

! AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres . Pour toute réparation faire appel à une personne compétente uniquement.

WARNING!!

AN INSULATED TRANSFORMER SHOULD BE USED DURING ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BECAUSE OF LIVE CHASSIS. THE CHASSIS OF THIS RECEIVER IS DIRECTLY CONNECTED TO THE AC POWER LINE.

SAFETY-RELATED COMPONENT WARNING !!

COMPONENTS IDENTIFIED BY A DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY .

! MARK ON THE SCHEMA TIC

ATTENTION!!

AFIN D’ÉVITER TOUT RISQUE D’ÉLECTROCUTION PROVENANT D’UN CHÂSSIS SOUS TENSION, UN TRANSFORMA TEUR D’ISOLEMENT DOIT ETRE UTILISÉ LORS DE TOUT DÉPANNA GE. LE CHÂSSIS DE CE RÉCEPTEUR EST DIRECTEMENT RACCORDÉ Á L’ALIMENTATION SECTEUR.

ATTENTION AUX COMPOSANTS RELATIFS Á LA

SÉCURITÉ!!

LES COMPOSANTS IDENTIFIÉS PAR UNE MAPQUE LES SCHÉMAS DE PRINCIPE, LES VUES EXPLOSÉES ET LES LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE NUMÉRO DE PIÈCE EST INDIQUÉ DANS LE PRÉSENT MANUEL OU DANS DES SUPPLÉMENTS PUBLIÉS PAR SONY.

VPL-CS5A/CS6/CX6/EX1

! SUR

For the customers in the Netherlands Voor de klanten in Nederland

Hoe u de batterijen moet verwijderen, leest u in de tekst van deze handleiding.

Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA).

Für Kunden in Deutschland

Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Kommunen. Entladen sind Batterien in der Regel dann, wenn das Gerät abschaltet und signalisiert “Batterie leer” oder nach längerer Gebrauchsdauer der Batterien “nicht mehr einwandfrei funktioniert”. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel.

VPL-CS5A/CS6/CX6/EX1

1 (P)

1. Service Overview

1-1. Appearance Figure ......................................................................................1-1

1-2. Board Locations ..........................................................................................1-1

1-3. Disassembly ................................................................................................1-2

1-3-1. Top Panel Assy Removal ...........................................................1-2

1-3-2. Side Panel Assy and L, NR, H2, Q Boards Removal ................1-2

1-3-3. Power Block (Lamp) Removal................................................... 1-3

1-3-4. DC Fan Removal........................................................................1-3

1-3-5. Lens Gear Removal .................................................................... 1-4

1-3-6. Speaker Assy and DC Fan (Sirocco) Removal ..........................1-4

1-3-7. C Board Removal .......................................................................1-5

1-3-8. MSC and MS (VPL-CX6) Boards Removal .............................. 1-5

1-3-9. GA and GB Boards Removal .....................................................1-6

1-3-10. Opt Unit Assy and Lamp Assy Removal ...................................1-7

1-3-11. PS Con Aperture (VPL-EX1) and S In-polarizer (R), (G), (B)

Removal .....................................................................................1-7

1-3-12. Projection Lens Assy, Lamp Duct Assy and

U Board Removal....................................................................... 1-8

1-3-13. S Prism Block Assy and

S Out-pre-polarizer (R), (G), (B) Removal ................................ 1-9

1-3-14. DC Fan (Sirocco) and V Board Removal ................................ 1-10

1-3-15. S Board Removal .....................................................................1-11

1-3-16. Extension Board and Extension Connectors ............................1-12

1-3-17. Extension Board and Extension Connectors Connection......... 1-13

1-3-18. Warning on Power Connection ................................................1-14

VPL-CS5A/CS6/CX6/EX1

2. Electrical Adjustments

2-1. Preparation ..................................................................................................2-1

2-1-1. Required Equipment................................................................... 2-1

2-1-2. Opt Unit Adjustment ..................................................................2-1

2-1-3. How to Enter the Factory Mode ................................................. 2-2

2-2. V COM Adjustment ....................................................................................2-2

2-3. Initial Values of Adjustment Items .............................................................2-3

2-4. Service Know-How ................................................................................... 2-11

2-4-1. When the S Prism Block Is Replaced ......................................2-11

2-4-2. When the C Board Is Replaced ................................................2-11

2-4-3. When the Adjuster Assy Is Returned

by the Emergency Mode ..........................................................2-11

2-5. White Balance Adjustment ....................................................................... 2-12

2-5-1. HIGH Mode of INPUT-A ........................................................2-12

2-5-2. LOW Mode of INPUT-A .........................................................2-12

2-5-3. HIGH Mode of VIDEO............................................................2-12

2-5-4. LOW Mode of VIDEO............................................................. 2-12

2-6. Memory Structure .....................................................................................2-13

3. Semiconductors................................................................................. 3-1

4. Spare Parts

4-1. Notes on Repair Parts..................................................................................4-1

4-2. Exploded Views ..........................................................................................4-2

4-3. Electrical Parts List ...................................................................................4-10

5. Block Diagrams

Overall ....................................................................................................................5-1

C (1/4), Q................................................................................................................5-2

C (2/4)..................................................................................................................... 5-3

C (3/4), H1, H2, L, V, U, NR .................................................................................5-4

C (4/4)..................................................................................................................... 5-5

MS, MSC ................................................................................................................ 5-6

GA, GB...................................................................................................................5-7

6. Diagrams

6-1. Frame Schematic Diagrams ........................................................................6-2

Frame (1/2) ...............................................................................................6-2

Frame (2/2) ...............................................................................................6-3

6-2. Schematic Diagrams and Board Layouts ....................................................6-4

Schematic Diagrams

Q................................................................................................................ 6-4

C (1/10) .....................................................................................................6-6

C (2/10) .....................................................................................................6-7

C (3/10) .....................................................................................................6-8

C (4/10) .....................................................................................................6-9

C (5/10) ...................................................................................................6-10

C (6/10) ...................................................................................................6-11

C (7/10) ...................................................................................................6-12

C (8/10) ...................................................................................................6-13

C (9/10) ...................................................................................................6-14

C (10/10) .................................................................................................6-15

V.............................................................................................................. 6-14

U.............................................................................................................. 6-14

S ..............................................................................................................6-15

H1............................................................................................................ 6-20

H2............................................................................................................ 6-21

L ..............................................................................................................6-22

NR ...........................................................................................................6-22

VPL-CS5A/CS6/CX6/EX1

MSC (1/2) ...............................................................................................6-23

MSC (2/2) ...............................................................................................6-24

MS (1/3) ..................................................................................................6-26

MS (2/3) ..................................................................................................6-27

MS (3/3) ..................................................................................................6-28

GA...........................................................................................................6-30

GB ...........................................................................................................6-33

Board Layouts

Q................................................................................................................ 6-5

C .............................................................................................................. 6-16

S ..............................................................................................................6-16

U.............................................................................................................. 6-16

V.............................................................................................................. 6-17

H1............................................................................................................ 6-20

H2............................................................................................................ 6-21

L ..............................................................................................................6-22

NR ...........................................................................................................6-22

MSC ........................................................................................................6-25

MS...........................................................................................................6-29

GA...........................................................................................................6-31

GB ...........................................................................................................6-34

VPL-CS5A/CS6/CX6/EX1

1-1. Appearance Figure

Section 1

Service Overview

1-2. Board Locations

MS (VPL-CX6 )

MSC

Power block (lamp)

VPL-CS5A/CS6/CX6/EX1

1-1

1-3. Disassembly

1-3-1. Top Panel Assy Removal

5 Top panel assy

3 Button (H1) assy

4 H1 board

2 Two screws

(+B 3 x 6)

1-3-2. Side Panel Assy and L, NR, H2, Q Boards Removal

4 L board

5 NR board

6 Screw

(+B 3 x 6)

CN914

CN915

8 H2 board

CN201

1 Six shafts

3 Side panel assy

7 Button (H2)

2 Two screws

(+B 3 x 6)

1-2

!- Q board

1 Connector cover

0 Video sleeve

9 Screw

(+B 3 x 6)

VPL-CS5A/CS6/CX6/EX1

1-3-3. Power Block (Lamp) Removal

2 Four screws (+B 3 x 20)

CN908

C board

CN909

3 Fan holder (EX2)

5 Two DC fans

4 T wo masks

1 Screw

(+B 3 x 6)

1 Two screws (+PTPWH 3 x 10)

2 Two screws (+B 3 x 6)

CN1

CN907

5 Sheet (LPS)

3 Holder (LPS2)

6 Power block (Lamp)

4 Holder (LPS1)

CN1

1-3-4. DC Fan Removal

VPL-CS5A/CS6/CX6/EX1

1-3

1-3-5. Lens Gear Removal

2 Lens gear

1 Two screws

(+BTP 3 x 12)

1-3-6. Speaker Assy and DC Fan (Sirocco) Removal

9 Speaker assy

5 Two screws

(+B 3 x 6)

CN1102

8 Speaker bracket

7 Speaker holder

6 Screw

(+B 3 x 6)

3 Two screws (+BTP 3 x 12)

CN912

1 Two screws (+B 3 x 6)

2 Fan (RE) holder

4 DC fan (Sirocco)

1-4

VPL-CS5A/CS6/CX6/EX1

1-3-7. C Board Removal

*1: Indicates the VPL-CX6/EX1. *2: Indicates the VPL-CS5A/CS6.

1 Three screws (+B 3 x 6)

CN1102

CN912

CN914

CN907

CN903

2 C board

CN910

CN911

CN901

CN1101

*1: CN501 *2: CN502

*1: CN601 *2: CN602

*1: CN701 *2: CN702

1-3-8. MSC and MS (VPL-CX6) Boards Removal

To remove the MS (VPL-CX6) board, remove the C board beforehand.

(VPL-CX6)

3 Two screws (+B 3 x 6)

CN1001

CN913

CN904

CN202

CN909

CN908

CN904

Flat connector assy

CN202 (VPL-CX6)

1 Screw (+B 3 x 6)

VPL-CS5A/CS6/CX6/EX1

Flat connector assy (12P)

CN1301

CN1303

CN1002

Flat connector assy (50P)

4 MS board

2 MSC board

1-5

1-3-9. GA and GB Boards Removal

To remove the GA and GB boards, remove the C board beforehand.

1 T wo screws (+B 3 x 6)

2 Screw (+B 3 x 6)

4 Holder (GA), Shield (GA)

5 GA board

3 Screw

(+B 3 x 6)

6 Holder GB

CN2001CN2002

CN3501

CN3301

CN3201

7 GB board

Flat connector assy (24P)

1-6

VPL-CS5A/CS6/CX6/EX1

1-3-10.Opt Unit Assy and Lamp Assy Removal

To remove the opt unit assy and lamp assy, remove C board and the DC fan beforehand.

4 Four screws (+P M4x12)

5 Opt unit assy

1 T wo screws

(+PWHTP 3 x 10)

2 Connector (Lamp)

3 T wo screws (+B 3 x 6)

6 Lamp house, Lamp top cover

Opt unit assy

7 Lamp assy

1-3-11.PS Con Aperture (VPL-EX1) and S In-polarizer (R), (G), (B) Removal

8 Three screws (+B 2 x 6)

9 S In-polarizer (G)

assy

0 S In-polarizer (R)

assy

!- S In-polarizer (B)

assy

5 P/S assy

1 T wo screws

(+B 2 x 6)

2 Unit cover (B), Six cushions

6 PS con aperture

(VPL-EX1)

7 Lens-2 fly eye

4 Lens-1 fly eye

Note when installing: (For the VPL-EX1, the protruded portion should be installed in the Lens-2 fly eye side.) (For the VPL-CS6/CX6/CS5A, the protruded portion should be installed in the UV-cut pre-filter side.)

3 UV-cut pre-filter

Opt unit assy

VPL-CS5A/CS6/CX6/EX1

Note :Do not disassemble the opt unit unless

specified by the above views.

1-7

1-3-12.Projection Lens Assy, Lamp Duct Assy and U Board Removal

To remove the projection lens assy, lamp duct assy and U board, remove the C board, opt unit assy and lamp assy beforehand.

4 T wo screws

1 Four screws

(+B 4 x 12)

(+B 3 x 6)

6 Screw (+B 3 x 6)

7 Holder U

3 Projection lens assy

2 Four screws

(+BSW M3 x 8)

8 U board

5 Lamp duct assy

1-8

VPL-CS5A/CS6/CX6/EX1

1-3-13.S Prism Block Assy and S Out-pre-polarizer (R), (G), (B) Removal

Do not touch the flexible cable, glass surface of S prism and especially the conductor surface of flexible cables.

Screw

(+PTP 2 x5)

Fastener (OP)

S Out-pre-polarizer (R)

S Prism block assy

S Out-pre-polarizer (B)

Screw

(+PTP 2 x5)

Fastener (OP)

S Out-pre-polarizer (G)

Screw

(+PTP 2 x5)

Fastener (OP)

VPL-CS5A/CS6/CX6/EX1

T wo screws

(+PS 3 x 6)

1-9

1-3-14.DC Fan (Sirocco) and V Board Removal

To remove the DC fan (sirocco) and V board, remove the C board, opt unit assy, lamp assy and S prism block assy beforehand.

3 Screw (+B 3 x 6)

5 T wo screws

(+BTP 3 x 12)

1 T wo screws (+B 3 x 6)

2 Prism duct

8 DC fan (sirocco)

6 DC fan (sirocco)

9 Fan holder (IN)

7 T wo screws

(+BTB 3 x 12)

4 V board

1-10

VPL-CS5A/CS6/CX6/EX1

1-3-15.S Board Removal

To remove the S board, remove the C board, opt unit Assy, lamp assy, S prism block assy and DC fan (sirocco) beforehand.

1 Adjuster section

2 Remove the

binding band

4 Two screws

(+P 2 x 4)

5 Remove the adjuster holder in the direction of the arrow.

Four screws

(+P 2 x 2.2)

6 Adjuster shaft

CN1

7 Adjuster frame assy

9 S board

Two screws

(+P 2 x 4)

VR shaft

VPL-CS5A/CS6/CX6/EX1

1-11

1-3-16.Extension Board and Extension Connectors

The numbers encircled by round corresponds to those of section 1-3-17.

VH connector assy (3P)

Flat connector assy (24P)

Five ZH connectors assy (3P)

Three flat connectors assy (32P)

(VPL-CX6/EX1)

Three flat connectors assy (24P)

(VPL-CS5A/CS6)

SR connector assy (4P)

ZH connector assy (5P)

SR connector assy (7P)

SR connector assy (14P)

SR connector assy (12P)

Three X2 boards

(VPL-CX6/EX1)

Three X3 boards

(VPL-CS5A/CS6)

X4 board

X5 board

SR connector assy (5P)

X1 board

1-12

X kit assy

(A-1603-729-A)

VPL-CS5A/CS6/CX6/EX1

NR board

L board

C board

MS board

(For VISCA)

(For writing the software)

H1 board

MSC board

From DC fan (Sirocco)

From DC fan

From V board

From adjustor unit

From DC fan (Sirocco)

From power block (Lamp), U board

Power block (Lamp)

GA board

GB board

Q board

H2 board

(VPL-CX6)

CN909

CN907

CN914

CN912

CN910

CN 110

CN 912

CN112

CN 111

CN 911

CN101

CN901

CN911

1: CN701

2: CN702

1: CN601

2: CN602

1: CN501

2: CN502

CN901

CN904

CN1101

CN915

CN3301

CN108

CN3501

CN2001

CN2002

CN1302

CN1303

CN913

CN800

CN301

CN1101

CN109

CN107

CN 907

CN909

CN201

CN903

CN908

CN 910

CN1

*1: Indicates the VPL-CX6/EX1. *2: Indicates the VPL-CS5A/CS6.

The numbers encircled by round corresponds to those of section 1-3-16.

CN202

*1:

*2:

*1:

*2:

*1:

*2:

*1:

*2:

1-3-17.Extension Board and Extension Connectors Connection

VPL-CS5A/CS6/CX6/EX1

1-13

1-3-18.Warning on Power Connection

Use the supplied power cord when you use the projector in your country. Otherwise, use a proper power cord meeting the following specification.

The United Continental UK Australia Japan States, Europe, Canada Korrea

Plug type YP-11 YP-21 SP-61 B8 YP-13 Female end YC-13L YC-13L YC-13L C7-2 YC-13L Cord type SPT-2 H03VVH2-F H03VVH2-F H03VVH2-F VCTFK Rated Voltage & Current 10 A/125 V 2.5 A/250 V 2.5 A/250 V 2.5 A/250 V 7 A/125 V Safety approval UL/CSA VDE BS SAA DENAN Cord length (max.) 4.5 m ____

1-14

VPL-CS5A/CS6/CX6/EX1

Section 2

Lens projection

Lens gear

Gear alignment portion

Electrical Adjustments

2-1. Preparation

2-1-1. Required Equipment

. Oscilloscope

Sony Tektronix 2465 or equivalent (350 MHz band width or more)

. NTSC, PAL, SECAM component signal generator

Sony Tektronix TG2000 + AVG1 (option module) + AWVG1 (option module) or equivalent

. VG (programmable video signal generator)

VG814 or equivalent

. Digital voltmeter

Advantest TR6845 or equivalent

. Illuminance meter

Allow the warm-up time of 5 minutes after the power is on before starting the following adjustments.

2-1-2. Opt Unit Adjustment

9. Tighten the adjustment plate fixing screw.

10. Tighten the six adjustment plate fixing screws manually with a torque driver. Tightening torque: 0.19 ±0.03 Nm

11. Check to see that the illumination range error is within the tolerable limit.

When installing the optical unit in this model, alignment of the gear tooth position is required. Perform the following steps.

Rotate the cooling fan and turn on the lamps.

(1) Mirror adjustment

Adjust the screen size to 80 inch at the WIDE end.

1. Select the green only mode.

2. Check to see if there is any black zone at the top, bottom, left or right of screen. If there is any black zone on screen, loosen the adjustment plate fixing screw and adjust the G dichroic mirror for minimum black zone.

3. Tighten the adjustment plate fixing screw.

4. Select the cyan only mode.

5. Check to see if there is any black zone at the top, bottom, left or right of screen. If there is any black zone on screen, loosen the adjustment plate fixing screw and adjust the RB mirror adjustment plate for minimum black zone and the blue color is distinguishing.

6. Tighten the adjustment plate fixing screw.

7. Select the all white mode.

8. Check to see if there is any black zone at the top, bottom, left or right of screen. If there is any black zone on screen, loosen the adjustment plate fixing screw and adjust the RB mirror adjustment plate for minimum black zone and the red color is distinguishing.

VPL-CS5A/CS6/CX6/EX1

Procedure

1. Rotate the lens focus and zoom in the fully clockwise positions. Lock the lens gear in the direction shown in Fig. 1.

Zoom

Lens gear

Focus

Fig. 1

2-1

2. Align the marking position of the lens zoom gear with the protrusion of the lens gear approximately by visual observation as shown below.

Zoom gear Lens gear

2-1-3. How to Enter the Factory Mode

1. Confirm that the MENU can be displayed.

2. Close the MENU.

3. Press the keys in the following order : [ENTER] → [ENTER] → [&] → [ENTER]. The message [Do you want to enter the Factory Mode? Yes : ↑ No : ↓] appears. Select [Yes : ↑].

Protrusion

Rib for marking

Fig. 2 (inside view)

Confirmation

Install the side panel and confirm that the portions A and B of the dial cannot be seen from the opening of the side

panel when the ZOOM and FOCUS are moved to their very ends.

ZOOM FOCUS ZOOM FOCUS

Good No good

[Supplementary information: How to Exit the Factory Mode]

Perform the step 3 KEY operation. The message [Do you want to return to the User Mode? Yes : ↑ No : ↓] appears. Select [Yes : ↑].

In the Factor mode, you can close the lens shutter if you keep pressing the TILT key even though the lamp lights. If the machine is left in this state for long hours, the lens shutter may melt in the worst case. Be sure to confirm that the lens shutter is not closed when the lamp lights in the Factory mode.

2-2. V COM Adjustment

1. Input the green-only, 30 IRE single-line ON/OFF signal to the input connector. (VPL-CS5A/CS6: SVGA signal, VPL-CX6/EX1 : XGA signal)

2. Enter the G VCOM adjustment screen of the Device Adjust.

3. Adjust the G VCOM value so that the flicker is minimal.

4. Switch the input signal from green-only to red-only then to blue only single-line ON/OFF signal. In the same way as step 3, adjust the R VCOM and B VCOM values respectively so that the flicker is minimal.

5. Take note of the adjustment values.

6. Set the “Image Flip” to either V or HV.

7. Input the above R/G/B adjustment values.

8. Take note of the adjustment values.

9. Set the “Image Flip” to OFF.

2-2

VPL-CS5A/CS6/CX6/EX1

MenuTitle ItemName MemoryName Remark

Set Memory Picture Memory W/B Memory

Video

S Video Input-A MS Video Computer

Dynamic Standard Dynamic Standard Dynamic Standard Dynamic Standard High Low High Low

PICTURE SETTING Picture Mode Standard

Adjust Picture...

Contrast 95 80 95 80 95 80 95 80 Brightness 40 50 40 50 40 50 40 50 Color 50 50 50 50 50 50 - Hue 50505050---Sharpness Middle Middle Middle Middle Middle Middle - RGB Enhancer ----20202020 Gamma Mode ----Graphics Graphics Graphics Graphics Color Temp. Low Low Low Low High High High High Volume 30

INPUT SETTING Adjust Signal...

Dot Phase 15(*1) H Size (*1)

Shift (*1) Wide Mode Off Off Off Off Off Off Off Off Scan Conv On On

SET SETTING Smart APA On

Auto Input Search Off Input-A Signal Sel. Computer Color System Auto Power Saving Off IR Reciever Front & Rear Illumination On

MENU SETTING Status On

Languege English Menu Position Center Menu Color White

INSTALL SETTING Tilt...

V Keystone Auto

Manual... 0 Image Flip Off Background Blue Lamp Mode(*2) Standard High Altitude Off Security Lock Off

Ke y Enter x 4

Status

Memory

2-3. Initial Values of Adjustment Items

VPL-CS5A/CS6/CX6/EX1

2-3

2-4

MenuTitle ItemName MemoryName Remark

Set Memory Picture Memory W/B Memory

Video

S Video Input-A MS Video Computer

Dynamic Standard Dynamic Standard Dynamic Standard Dynamic Standard High Low High Low

INFORMATION fH Display only

fV Display only (Memory No.) Display only (Resolution) Display only Lamp Timer Display only ROM Version Display only SC ROM Version Display only Operation Timer Display only Prev. Lamp Timer Display only

W/B SETTING Gain R 182 182 160 160

G 182 150 160 140 B 182 160 160 150 Bias R 85 85 85 85 G 85 85 85 85 B 85 85 85 85

*1 The "Dot Phase E,H Size,Shift H/V and Picture Mode" items in the "INPUT SETTING" menu have their respective initial values for each

input signal(PRESET MEMORY No.).

*2 VPL-CS5A is not indicated. There are some adjustment items that cannot be adjusted, depending on the input signal.

Status

Memory

(VPL-CS5A/CS6/CX6/EX1)

VPL-CS5A/CS6/CX6/EX1

DeviceName ItemName MemoryName Remark

Set Memory

Status

Memory

Chroma Memory Channel Memory Image Flip Memory

NT358/

NT443 /BW60

Pal/Pal-M/N/

Secam/BW50

15kRGB

Component

(15k)

Video

Input-

Up/Down

inversion is

possible.

A/D Converter ADC/ Clamp Position 8

Clamp Width 20 R Gain(Other) - - 100 R Gain(Component) --R Gain(VideoGBR) --G Gain(Other) - - 100 G Gain(Component) --G Gain(VideoGBR) --B Gain(Other) - - 100 B Gain(Component) --B Gain(VideoGBR) --R Offset(Other) - - 128 R Offset(Component) --R Offset(VideoGBR) --G Offset(Other) - - 128 G Offset(Component) --G Offset(VideoGBR) --B Offset(Other) --128 B Offset(Component) --B Offset(VideoGBR) --Sync Sep Th 32 Pre Coast 2 Post Coast 8

Chroma/D.Comb Chroma/ Ch1 Gain 20 20 144

Ch2 Gain 144 16 160 Video Brt 140 12 4 128 128 Video Cont 64 64 64 64 Sub Color 56 56 56 56 LCBW 000 Y-DeLay * Ch3 Gain 144 144 160 Ch4 Gain 144 144 160 YUV Brt 12 8 128 12 8 12 8 YUV Cont 64 64 64 64 AOSL 1E

Display only

VPL-CS5A/CS6

Up/Down inversion is impossible.

2-5

2-6

DeviceName ItemName MemoryName Remark

Set Memory

Status

Memory

Chroma Memory Channel Memory Image Flip Memory

NT358/

NT443 /BW60

Pal/Pal-M/N/

Secam/BW50

15kRGB

Component

(15k)

Video

Input-

Up/Down

inversion is

possible.

Panel Driver P.Drv Offset R 214 214

Offset G 214 214

Offset B 214 214

V Common R 55 55

V Common G 55 55

V Common B 55 55

Psig 1 58

Psig 2 130

Signal Center 193

Gain R 166

Gain G 166

Gain B 166

DCFB Off 1

Sample Hold/ SH1 7

Other/ V Com Ptn Enb

Adj. Not possible

Installation 0

Other 3D Gamma Sub Cont 0

Sub Brt 0

R Osd Lvl 31

G Osd Lvl 31

B Osd Lvl 31

Through 0

SW 1

APC Thres 25

APC Limit 32

Other/ V Start 22

H Start(MSB) 10 4

H Start(LSB) 0

H Position 33

HST Position 9

HST Phase 3

Temp Lamp

Adj. Not possible

Temp Panel

Adj. Not possible

Fan1 H