Sony UNI-ONS7C1 Specsheet

UNI-ONS7C1/T1, UNI-ONS7C1W/T1W, UNI-INS7C1/T1 & UNI-INS7C3/T3
Security Camera Enclosures
Dome Enclosures
The UNI-ONS7C1/T1, UNI-ONS7C1W/T1W, UNI-INS7C1/T1 & UNI-INL7C3/T3 domes offer versatility and camera protection in a compact size. These inconspicuous dome housings are specifically designed to accommodate Sony’s SNC-RZ30 and SNC-RZ50 cameras. The housings offer versatility, easy installation and outstanding camera protection in a compact size.
KEY FEATURES
Easy camera installation designed for SNC-RZ series of cameras.
Constructed of durable engineered plastic top, 94VO, with UV protected lower dome.
Cast aluminum pendant mount is standard.
Optically clear .118-inch (3mm) thick aspheric polycarbonate dome.
Thermostatically controlled 24VAC heater (UNI-ONS7C1 & UNI-ONS7C1W models).
Separate power input for heater, blower and camera power.
Wireless ready model is the UNI-ONS7C1W or the UNI-ONS7T1W.
AC 24V external input, regulated DC12V for cameras inside provided.
IR Illuminator
(Images 1)
BID SPECIFICATIONS
The outdoor dome camera housing shall be a Sony model UNI-ONS7C1/T1, UNI-ONS7C1W/T1W. The indoor model shall be
a Sony model UNI-INS7C1/T1, UNI-INS7C3/T3. The housing shall be designed for the SNC-RZ30 and SNC-RZ50 cameras. Both models should come standard with a pendant mount. The Sony model UNI-ONS7C1/T1 and UNI-ONS7C1W/T1W shall also be equipped with 24VAC input blowers and thermostatically controlled heaters. UNI-ONS7C1/T1, UNI-ONS7C1W/T1W and UNI-INS7C1/T1 will include a 24VAC to 12VDC power supply built into the housing. The UNI-INS7C3/T3 does not include any electronics, and 12VDC must be supplied to the housing. The upper dome housing shall be manufactured from a high-impact engineered plastic, UV protected, with a UL flame rating of 94V0. The dome shall be made of an injection molded, 3mm thick, optically clear thermoplastic polycarbonate. The dome shall be held in place with minimum of three (3) fasteners, and a safety cable shall be provided to hold the dome while servicing. Access to the enclosure shall be from below with three (3) captive fasteners used to press the dome against a sealing O-ring. A twist-off feature shall allow for the final removal of the dome. The wiring enters through the top of the housing on all models. The engineered plastic top, with its reflective white paint, insulates internal equipment. On the Sony models UNI-ONS7C1/T1 and UNI-ONS7C1W/T1W models the blower shall draw 1.4W continuous power. The 25W heater shall turn on at 50°F (10°C) and turn off at 77°F (25°C). The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C).
Note: To achieve the increased depth with the aspheric design for optimal camera lens to capsule orientation, the capsule is slightly
angled around the highest section. This creates a “line’, visible to the naked eye, around the upper most section of the capsule. This “line” serves as the geometric center line used to insure proper camera placement. It is not typically seen by the camera. However, Sony RZ series PTZ cameras are able to tilt up above the horizon to 25°, this wide range of tilt motion at a wide angle view may cause this line to be captured in the image.
SPECIFICATIONS
Electrical
Heater and blower 24VAC, 27 Watts Camera 24VAC, 25 Watts UNI-INS7C1 camera 24VAC, 25 Watts UNI-INS7C3 camera 12VDC 25 Watts (see camera instructions)
Mechanical
Size (H x W x D) 10.3 x 10.3 x 14.6 inches (262 x 262 x 371mm) Weight 7 lbs. (3.5 kg) without camera Upper housing .08-inch (2.0mm) plastic top, 94VO flame rated, and UV protected Lower dome .118-inch (3mm), optically clear, thermoplastic polycarbonate Mounting brackets Cast or machined aluminum
Models
UNI-ONS7C1 Outdoor, pendant mount, clear dome housing with 24VAC input and heater/blower, 24VAC to 12VDC power supply
UNI-ONS7T1 UNI-ONS7C1 with a tinted lower dome UNI-ONS7C1W Outdoor, pendant mount, clear dome housing with 24VAC input and heater/blower, 24VAC to 12VDC power supply
UNI-ONS7T1W UNI-ONS7C1W with a tinted lower dome UNI-INS7C1 Indoor, pendant mount, clear dome housing with 24VAC input and 24VAC to 12VDC power supply included UNI-INS7T1 UNI-INS7C1 with a tinted lower dome UNI-INS7C3 Indoor, pendant mount, clear dome housing without any electrical power or wiring UNI-INS7T3 UNI-INL7C2 with a tinted lower dome
Environmental
Operating temperature -20°F (-29°C) to 122°F (50°C) Heater activates at 50°F (10°C), deactivates at 77°F (25°C), 24VAC, 25W Blower Continuous operation
Shipping
Box dimension (H x W x D) 12 x 12 x 19 inches (305 x 305 x 483mm) Weight 11 lbs. (5 kg)
Accessories
UNI-WMB1 Aluminum gooseneck wall mount, white finish UNI-RMB1 Aluminum parapet mount, white finish UNI-CMA1 Aluminum corner mount adapter, white finish (must be used with UNI-WMB1) UNI-PMA1 Aluminum existing pole mount adapter, white finish (must be used with UNI-WMB1) UNI-WMB3 Wall/pendant adapter bracket for outdoor mini dome cameras UNI-WMBB1 Aluminum pole/wall mount adapter bracket with straps UNI-PBU1 Wall/pendant adapter bracket for outdoor mini dome cameras
included
included. Include wireless antenna cable (must be used with SNCA-CFW1 & SNCA-AN1)
UNI-ONS7C1 & UNI-ONS7C1W
SYSTEM CONFIGURATIONS
UNI-ONS7C1
UNI-ONS7C1W
DIMENSIONS
10.27
O
260.9
Network
Wireless
Access Point
HD monitor
Recording Server NSR-1000 Series
Recording Software
IMZ-NS100 Series
PC
Unit: inches (mm)
Sony Electronics Inc. 1 Sony Drive Park Ridge, NJ 07656 sony.com/security
1 1/2 INCH NPT
1.94
49.1
9.53
242.1
3.70
R
94.1
Reproduction in whole or in part without written permission is prohibited.
Features and specifications are subject to change without notice.
Sony and the Sony make.believe logo are trademarks of Sony.
© 2012 Sony Electronics Inc. All rights reserved.
Weights and measurements are approximate.
13.67
347.3
U-ONS7/INS7
Printed in USA (05/12)
Loading...