Sony UNI-ONL7T2 Specsheet

UNI-ONL7C2/T2, UNI-ONL7C2W/T2W
& UNI-INL7C2/T2

Security Camera Enclosures

Outdoor & Indoor
Dome Enclosures

The UNI-ONL7C2/T2, UNI-ONL7C2W/T2W &
UNI-INL7C2/T2 (7-inch) domes offer versatility,
easy installation and camera protection in a
compact size. These inconspicuous dome
housings are specifically designed to
accommodate Sony’s SNC-RX, SNC-RH, SNC-RS,
SNC-ER/EP and SNC-ZR/ZP series of cameras.

KEY FEATURES

• Compatible with Sony’s SNC-RX, SNC-RH, SNC-RS, SNC-ER/EP and SNC-ZR/ZP series of cameras.

• Easy camera installation.

• Constructed of durable engineered plastic top, 94VO, with UV protected lower dome.

• Cast aluminum pendant mount is standard.

• Optically clear .118-inch (3mm) thick aspheric polycarbonate dome.

• Thermostatically controlled 24VAC heater (UNI-ONL7C2 & UNI-ONL7C2W models).

•

24-Hour fan operation for effective heating and condensation protection (UNI-ONL7C2 & UNI-ONL7C2W models).

• Wireless ready models UNI-ONL7C2W and UNI-ONL7T2W, external antenna interface is N-type connector .

• AC 24V external input, regulated DC12V for cameras inside provided.

IR Illuminator

(Images 1)

BID SPECIFICATIONS

• The outdoor dome camera housing shall be a Sony model UNI-ONL7C2, UNI-ONL7C2W. The indoor model shall be a Sony

model UNI-INL7C2. The housing shall be designed for the SNC-RX, SNC-RZ25, SNC-RS, SNC-RH, SNC-EP/ER and SNC-ZR/ZP
series of cameras. All models shall come standard with a 1.5” NPT pendant mount. The Sony model UNI-ONL7C2/T2 &
UNI-ONL7C2W/T2W shall also be equipped with 24VAC input blowers and thermostatically controlled heaters. The products
housing shall be manufactured from a high-impact engineered plastic, UV protected, with a UL flame rating of 94V0. The
dome shall be made of an injection molded, 3mm thick, optically clear thermoplastic polycarbonate. The dome shall be
held in place with minimum of three (3) fasteners, and a safety cable shall be provided to hold the dome while servicing.
Access to the enclosure shall be from below, with three (3) captive fasteners used to press the dome against a sealing
O-ring. A twist-off feature shall allow for the final removal of the dome. The wiring enters through the top of the housing on
all models. The engineered plastic top, with its reflective white paint, insulates internal equipment. UNI-ONL7C2W includes
a pre-run wireless antenna cable (must be used with SNCA-CFW1 & SNCA-AN1* model sold separately). *Note: please refer
to camera specs for appropriate model.

On the Sony UNI-ONL7C2, UNI-ONL7C2W and UNI-ONL7T2, UNI-ONL7T2W models, the blower shall draw 1.4W continuous
power. The 25W heater shall turn on at 50°F (10°C) and turn off at 77°F (25°C). The housing shall support a temperature
range of -20°F (-29°C) to 122°F (50°C). The output connector on top of the wireless ready enclosure shall be female
N-type connector.

Note: To achieve the increased depth with the aspheric design for optimal camera lens to capsule orientation, the capsule is slightly

•

angled around the highest section. This creates a “line’, visible to the naked eye, around the upper most section of the capsule. This
“line” serves as the geometric center line used to insure proper camera placement. It is not typically seen by the camera except on
some Sony cameras that have above horizon tilt.

SPECIFICATIONS

Electrical

Heater and blower 24VAC, 27 Watts
Camera 24VAC, 25 Watts

Mechanical

Size (H x W x D) 10.3 x 10.3 x 15 inches (262 x 262 x 381mm)
Weight 7 lbs. (3.5 kg) without camera
Upper housing .08-inch (2.0mm) plastic top, 94VO flame rated, and UV protected
Lower dome .118-inch (3mm), optically clear, thermoplastic polycarbonate
Mounting brackets Cast or machined aluminum

Models

UNI-ONL7C2 Outdoor, pendant mount, clear dome housing with 24VAC input and heater/blower
UNI-ONL7T2 UNI-ONL7C2 with a tinted lower dome
UNI-ONL7C2W Outdoor, pendant mount, clear dome housing with 24VAC input and heater/blower. Include wireless antenna cable

UNI-ONL7T2W UNI-ONL7C2W with a tinted lower dome
UNI-INL7C2 Indoor, pendant mount, clear dome housing without any electrical power or wiring
UNI-INL7T2 UNI-INL7C2 with a tinted lower dome

Environmental

Operating temperature -20°F (-29°C) to 122°F (50°C)
Heater activates at 50°F (10°C), deactivates at 77°F (25°C), 24VAC, 25W
Blower Continuous operation

Shipping

Box dimension (H x W x D) 12 x 12 x 19 inches (305 x 305 x 483mm)
Weight 11 lbs. (5 kg)

Accessories

UNI-WMB1 Aluminum gooseneck wall mount, white finish
UNI-RMB1 Aluminum parapet mount, white finish
UNI-CMA1 Aluminum corner mount adapter, white finish (must be used with UNI-WMB1)
UNI-PMA1 Aluminum pole mount adapter, white finish (must be used with UNI-WMB3)
UNI-WMB3 Aluminum pole mount adapter, white finish

UNI-ONL7C2, UNI-ONL7C2W, UNI-INL7C2 & UNI-ONL7T2, UNI-ONL7T2W, UNI-INL7T2

(must be used with SNCA-CFW1 & SNCA-AN1)

SYSTEM CONFIGURATIONS

UNI-ONL7C2

UNI-ONL7C2W

DIMENSIONS

10.27

O

260.9

Network

Wireless

Access Point

HD monitor

Recording Server
NSR-1000 Series

Recording Software

IMZ-NS100 Series

PC

Unit: inches (mm)

Sony Electronics Inc.
1 Sony Drive
Park Ridge, NJ 07656
sony.com/security

1 1/2 INCH NPT

1.94

49.3

10.80

274.2

3.70

R

94.1

Reproduction in whole or in part without written permission is prohibited.

Features and specifications are subject to change without notice.

Sony and the Sony make.beleive logo are trademarks of Sony.

© 2012 Sony Electronics Inc. All rights reserved.

Weights and measurements are approximate.

14.96
380

U-ONL7/INL

Printed in USA (05/12)