Sony TRV330, TRV120, TRV530, TRV730, TRV30 User Manual

Owner’s Manual
For Sony TRV30, TRV730, TRV530, TRV330 and TRV120 Camcorders
www.uwimaging.com
Table of Contents
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Operation of the Stingray II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Optic Installation and Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Monitor Back ID and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Pre-Dive Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
First Time Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
After Diving Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Housing Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
O-ring Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Returning Products for Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Contact Light and Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Welcome
Congratulations on your purchase of a Stingray II video housing.
Please inspect the packaging of your product to verify that there was no damage during shipping.
If you are not familiar with your camcorder’s features, please take time to become familiar with the camcorder before you proceed in this manual. This manual assumes you have a working knowledge of your camcorder and will only cover operational procedures relative to the underwater housing.
The term “Push” when referenced in this manual means to press and release in one motion. If a function requires a button to be continually held, the manual will read, “press and hold”.
Periodically refer to the website for instruction revisions. http://www.uwimaging.com
"
#$
Hot Tip Important Caution
Look for these symbols to help identify special information.
Caution - Caution - Caution
We hope you have a wonderful underwater experience with Light & Motion equipment. To increase your enjoyment and the life span of your new gear please take an extra minute to review common errors which will result in equipment damage or destruction.
Check the operation of all your equipment several weeks prior to your trip. If maintenance or repair is necessary, then time is available for both shipping and repair scheduling.
Never transport or ship the housing with the camcorder inside. This may damage your camcorder.
Never leave your housing in the rinse bucket, it may be damaged by other equipment.
When removing the camcorder from the housing after a dive, do so in a dry controlled environment away from other SCUBA related equipment. This prevents water from other equipment or water from another diver accidentally entering the housing.
If a product is flooded, immediately rinse it with fresh water. Most non­electrical parts will be salvageable if not corroded by salt water
Getting Started
Illustrated below are the locations of Stingray’s features, ports, and functions. Take time to familiarize yourself with the housing.
Camera Preparation
1) Install the appropriate fully charged Sony camcorder battery.
2) Install a Sony MiniDV tape or Digital8 tape into your camcorder.
3) Install a Memory Stick in your camcorder
Mounting the Camera
1. Remove the rear plate by simultaneously rotating both latches down and rearward of the housing body.
2. Remove the Camera Tray. A. Push forward on the Camera Tray. B. Press the Camera tray Release Button down. Camera Tray is spring loaded and will slide out of housing.
3. Position the Camera Tray underneath the camera, oriented with the multi­colored power cable to the rear of the camcorder.
4. Secure the camcorder to the Camera Tray by tightening the Camera Tray Mounting Screw into the tripod mount of the camcorder.
5. Remove the camcorder’s DC in cover, LANC cover and Video Jacks cover.
6. Insert the larger front cable into the camcorder’s red MIC jack.
7. Insert the rear black cable into the camcorder’s yellow AUDIO/VIDEO jack.
8. Insert the rear multi-colored cable into the camcorder’s HOT SHOE mount. Check the seat of the cable in the HOT SHOE mount and insure that it is all the way forward and completely seated.
9. TRV30, 330 and 530 only: Extend the Viewfinder backward until it locks at its furthest extension.
10. Align front of Camera Tray with base of housing and partially slide into housing.
11. Before sliding all the way into the housing, insert cable (from housing) into the camcorder’s blue LANC jack.
Video Router Dial
(Fig. 6 TRV330, TRV530 and TRV730)
Loading...
+ 4 hidden pages