Sony TRV510, TRV510E Service Manual
DCR-TRV410/TRV410E/
TRV510/TRV510E
RMT-814
US Model
Canadian Model
DCR-TRV510
AEP Model
UK Model
DCR-TRV410E/TRV510E
E Model
Hong Kong Model
Tourist Model
DCR-TRV410/TRV410E
Australian Model
Chinese Model
DCR-TRV410E
MICROFILM
B800 MECHANISM
DIGITAL VIDEO CAMERA RECORDER
Photo: DCR-TRV510
For MECHANISM ADJUSTMENT, refer to
the “8mm Video MECHANICAL
ADJUSTMENT MANUAL
” (9-973-801-11).
SPECIFICATIONS
• Abbreviation
HK : Hong Kong model
JE : Tourist model
AUS : Australian model
CN : Chinese model
NTSC MODEL : DCR-TRV410/TRV510
PAL MODEL : DCR-TRV410E/TRV510E
SERVICE MANUAL
Ver 1.0 1999.03
DCR-TRV410/TRV410E/TRV510/TRV510E
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
(For printed wiring boards)
• b: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
isn’t mounted in this model.
• Chip parts.
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µµF.
50V or less are not indicated except for electrolytics and
tantalums.
• Chip resistors are 1/10W unless otherwise noted.
kΩ=1000Ω, MΩ=1000kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example C541 L452
22U 10UH
TA A 2520
• Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have char acteristic curve B,
unless otherwise noted.
• Signal name
XEDIT→ EDIT PB/XREC → PB/REC
• 2 : non flammable resistor
• 1 : fusible resistor
• C : panel designation
• A : B+ Line
• B : B– Line
• J : IN/OUT direction of (+,–) B LINE.
• C : adjustment for repair.
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of
pattern box. They are reference values and reference waveforms.
(VOM of DC 10 MΩ input impedance is used.).
• Voltage v alues change depending upon input impedance of V OM
used.)
1. Connection
2. Adjust the distance so that the output waveform of Fig. a and
the Fig. b can be obtain.
Yellow
AABBA=B
Fig. a (Video output terminal output waveform)
Fig.b (Picture on monitor TV)
Electron beam
scanned frame
CRT picture frame
H
Cyan
Green
White
Magenta
Red
Blue
Yellow
Cyan
Green
White
Magenta
Red
Blue
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
CBE5
64
2
13
5
46
2
31
45
2
31
12
4
53
3213213
21
Transistor Diode
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
Note :
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
When indicating parts by reference number, pleas include
the board name.
CD-212 (CCD IMAGER) PRINTED WIRING BOARD (720H MODEL)
— Ref. No. CD-212 Board; 10,000 Series —
CD-212 BOARD
4-9 4-10 4-11
CCD IMAGER
CD-212
Front of the lens
1.5 m
Pattern box
For printed wiring boards
• This board is eight-layer print board. Howe ver , the patterns of layers two to seven have not been included in
the diagram.
• Chip parts
Transistor
There are few cases that the part printed on this
diagram isn’t mounted in this model.
C
BE
C1401 B-1
C1402 A-1
C1403 B-1
C1404 B-2
C1405 A-1
C1406 A-1
C1407 A-2
C1408 B-1
C1409 B-2
C1410 B-2
C1411 B-2
CN1401 B-3
IC1401 A-3
IC1402 B-2
IC1403 B-1
L1401 B-1
L1402 A-1
Q1401 B-2
R1401 B-1
R1402 A-1
R1403 B-2
R1404 B-2
R1405 B-2
R1406 B-2
R1408 B-2
CD-212
BOARD
CAMERA REC
2 IC1401 3,4
3 IC1401 7
4 IC1401 !™
1.2Vp-p
H
3.3Vp-p
5 IC1401 !£,!¢
3.7Vp-p
H
1.3Vp-p
7 Q1401 E
1 IC1401 1,2
6.5Vp-p
H
6 IC1401 0
18Vp-p
H
6.5Vp-p
H
74 nsec 74 nsec
CD-212 (TRV410/TRV510)
CD-213 (TRV410E/TRV510E)
(CCD IMAGER)
PC-72 (TRV510/TRV510E)
HONEY, JPEG
D/D CONV, INTERFACE
FLASH MEMORY,
DIGITAL STILL CONTROLLER
MA-356
STEREO MIC AMP,
LASER LINK
PJ-97
(AV IN/OUT)
SE-88
(STEADY SHOT)
DD-117
(DC/DC CONVERTER)
VF-126
(COLOR EVF)
DCR-TRV410/TRV410E/TRV510/TRV510E
CD-213 (CCD IMAGER) PRINTED WIRING BOARD (960H MODEL)
— Ref. No. CD-213 Board; 10,000 Series —
4-13 4-14
CCD IMAGER
CD-213
CD-213 BOARD
For printed wiring boards
• This board is eight-layer print board. Howe ver , the patterns of layers two to seven have not been included in
the diagram.
• Chip parts
Transistor
There are few cases that the part printed on this
diagram isn’t mounted in this model.
C
BE
C2401 B-1
C2402 A-1
C2403 B-1
C2404 B-2
C2406 A-1
C2407 A-1
C2408 B-1
C2409 A-2
C2410 B-2
C2411 A-2
CN2401 B-3
IC2401 A-3
IC2402 B-2
IC2403 B-2
L2401 B-1
L2402 B-1
Q2401 A-1
R2401 B-2
R2402 A-1
R2403 B-2
R2404 B-2
R2405 B-2
R2406 B-2
CD-213
BOARD
CAMERA REC
2 IC2401 3,4
3 IC2401 8
4 IC2401 !º
0.9Vp-p
H
3.0Vp-p
56 nsec
56 nsec
5 IC2401 !¡,!™
3.0Vp-p
H
1.0Vp-p
7 IC2402 1
1 IC2401 1,2
6.5Vp-p
H
6 IC2401 !£
18Vp-p
H
6.5Vp-p
H
DCR-TRV410/TRV410E/TRV510/TRV510E
CD-212 (TRV410/TRV510)
CD-213 (TRV410E/TRV510E)
(CCD IMAGER)
PC-72 (TRV510/TRV510E)
HONEY, JPEG
D/D CONV, INTERFACE
FLASH MEMORY,
DIGITAL STILL CONTROLLER
MA-356
STEREO MIC AMP,
LASER LINK
PJ-97
(AV IN/OUT)
SE-88
(STEADY SHOT)
DD-117
(DC/DC CONVERTER)
VF-126
(COLOR EVF)
DCR-TRV410/TRV410E/TRV510/TRV510E
For schematic diagram
• Refer to page 4-65 for printed wiring board.
4-15 4-16 4-17
CAMERA PROCESSOR
VC-213 (1/13)
VC-213
BOARD (1/13)
2
IC501 !¡
CAMERA REC/PB
1
IC501 5
CAMERA REC/PB
3.0Vp-p
3.0Vp-p
NTSC: 1.2Vp-p
PAL: 0.9Vp-p
3
IC501 @¡
CAMERA REC
3.0Vp-p
NTSC: 74 nsec
PAL: 56 nsec
4
IC501 @§
CAMERA REC
H
7.0Vp-p
5
IC501 @•
CAMERA REC
H
7.0Vp-p
6
IC502 2 – 9
CAMERA REC/PB
NTSC: 74 nsec
PAL: 56 nsec
2.9Vp-p
7
IC502 !º
CAMERA REC
2.9Vp-p
7
IC502 !º PB
2.9Vp-p
NTSC: 13.5 MHz
PAL: 18.00 MHz
NTSC: 27.00 MHz
PAL: 36.00 MHz
9
IC502 @§
CAMERA REC
8
IC502 !§
CAMERA REC/PB
LINE REC
H
2.9Vp-p
NTSC: 13.50 MHz
PAL: 18.00 MHz
NTSC:74 nsec
PAL:56 nsec
NTSC: 74 nsec
PAL: 56 nsec
DCR-TRV410/TRV410E/TRV510/TRV510E
For schematic diagram
• Refer to page 4-65 for printed wiring board.
4-18 4-19 4-20
Y/C PROCESSOR
VC-213 (2/13)
VC-213
BOARD (2/13)
0
IC251 $¶, L257
LINE REC/PB
3.0Vp-p
NTSC :13.3 MHz
PAL : 13.6 MHz
DCR-TRV410/TRV410E/TRV510/TRV510E
For schematic diagram
• Refer to page 4-65 for printed wiring board.
4-21 4-22
LENS MOTOR DRIVE
VC-213 (3/13)
DCR-TRV410/TRV410E/TRV510/TRV510E
DCR-TRV410/TRV410E/TRV510/TRV510E
For schematic diagram
• Refer to page 4-65 for printed wiring board.
4-26 4-274-25
I/O SEL, IR, BBI
VC-213 (4/13)
4-28
VC-213 BOARD (4/13)
!£ IC643 !™
CAMERA REC/PB
!¢ IC643 !§
CAMERA REC/PB
1.0Vp-p
H
1.5Vp-p
H
!∞ IC643 @¶ PB
H
0.5Vp-p
H
H
0.3Vp-p
!§ IC643 @ª PB
!™ IC643 9, IC644 $¡
CAMERA REC/PB
IR ON
0.5Vp-p
H
!¶ IC643 #¡ PB
0.5Vp-p
!¡ IC643 7
CAMERA REC/PB
2Vp-p
H
DCR-TRV410/TRV410E/TRV510/TRV510E
For schematic diagram
• Refer to page 4-65 for printed wiring board.
4-29 4-30
VFD
VC-213 (5/13)
4-31
VC-213
BOARD (5/13)
!ª
Q352 E
LINE REC
!•
Q351 E
CAMERA REC/PB
!•
Q351 E
LINE REC
0.15Vp-p
H
0.4Vp-p
H
@º
Q353 E
CAMERA REC/PB
H
0.4Vp-p
H
0.4Vp-p
@º
Q353 E
LINE REC
!ª
Q352 E
CAMERA REC/PB
0.4Vp-p
H
0.4Vp-p
H
DCR-TRV410/TRV410E/TRV510/TRV510E
For schematic diagram
• Refer to page 4-65 for printed wiring board.
4-33 4-344-32
SFD, TFD, LIP
VC-213 (6/13)
VC-213
BOARD (6/13)
CAMERA REC/PB
@¡
IC301 !¢ (R315)
2.6Vp-p
24.58MHz
DCR-TRV410/TRV410E/TRV510/TRV510E
Loading...