Sony TC-WR661, TC-WE405 User Manual
Ster eo
Cassette Deck
3-810-312-31(1)
Operating Instructions
Mode d’emploi
Manual de instrucciones
Manual de Instruções
EN
EN
GB
GB
F
F
ES
ES
P
P
TC-WE405
TC-WR661
1996 by Sony Corporation
3-810-312-31(1)
WARNING
To prevent fire or shock
hazard, do not expose
the unit to rain or
moisture.
EN
2
3-810-312-31(1)
Welcome!
Thank you for purchasing the Sony
Stereo Cassette Deck. Before operating
the unit, please read this manual
thoroughly and retain it for future
reference.
About This Manual
The instructions in this manual are for
models TC-WE405 and TC-WR661.
Check your model number by looking
at the rear panel of your tape deck. In
this manual, the TC-WE405 is the model
used for illustration purposes. Any
difference in operation is clearly
indicated in the text, for example, “TCWE405 only.”
Type of differences
Model
Feature
Dolby HX PRO
PHONES jack
Convention
The following icon is used in this
manual:
WE405
•
•
WR661
TABLE OF CONTENTS
Getting Started
Unpacking 4
Hooking Up the System 4
Playing a Tape 5
Recording on a Tape 6
Advanced Recording Operations
Adjusting the Recording Level Automatically (Auto Rec Level) 8
Fading In and Out (Fader) 9
Dubbing a Tape 9
Inserting a Blank Space During Recording (Record Muting) 10
Additional Information
Precautions 11
Notes on Cassette Tapes 11
Cleaning 12
Troubleshooting 13
Specifications 14
Index 15
EN
Indicates hints and tips for
z
making the task easier.
EN
3
3-810-312-31(1)
Getting Started
Ç
ç
REC OUT IN
LINE
OUTIN
L
R
TAPE
L
R
L
R
Getting Started
Unpacking
Check that you received the following items:
• Audio connecting cords (2)
Hooking Up the System
This section describes how to hook up the tape deck to
an amplifier. Be sure to turn off the power of each
component before making the connections.
To purchasers of the TC-WR661
For information on connecting your tape deck to the TAAV561 Amplifier, refer to the Operating Instructions
included with the TA-AV561.
Hookups
When connecting an audio connecting cord, be sure to
match the color-coded cord to the appropriate jacks on
the components: Red (right) to Red and White (left) to
White. Be sure to make connections firmly to avoid
hum and noise.
Connect the tape deck to the amplifier as shown below.
Tape deck Amplifier
ç: Signal flow
To purchasers of the TC-WE405
Follow the instructions below to connect your tape deck to
an amplifier.
TC-WE405
to LINE IN
to REC OUT
to LINE OUT
to TAPE IN
to an AC
outlet
Amplifier
to a
wall outlet
Setting the voltage selector (only on
models supplied with a voltage selector)
Check that the voltage selector on the rear panel of the
tape deck is set to the local power line voltage. If not,
set the selector to the correct position using a
screwdriver before connecting the AC power cord to
an AC outlet.
VOLTAGE
220V
240V
120V
Connecting the AC power cord
Connect the AC power cord to an AC outlet.
Where do I go next?
Now you’re ready to use your tape deck.
For basic operations, go to pages 5 to 7; for advanced
operations, go to the sections starting from page 8.
EN
4
3-810-312-31(1)
Basic Operations
Playing a Tape
24 3
DECK A DECK B
COUNTER RESET
0
p
)
ª·
§
POWER
Basic Operations
AUTO
REC LEVEL
DOLBY NR
DIRECTION
RELAY
Da
SYNCHRO DUBBING A→B
HIGH/NORMAL
START(DECK B P)
PAUSE REC MUTE REC
PrR
0)
p
§
OFF B C
FADER ARL
ª·
5
6
4
3
2
1
0
10
PHONES
7
8
9
• See page 4 for hookup
information.
• You can use either deck for
playback.
z To locate the beginning of
a tape and start playback
automatically (Auto Play)
Press 0 while holding
down ·. For the reverse
side, press ) while holding
down ª.
z To play a tape recorded
with the Dolby NR*
system
Set DOLBY NR to the same
position that the tape was
recorded in—B or C.
z What is the Dolby NR
system?
The Dolby NR (noise
reduction) system eliminates
tape hiss noise by boosting
low-level signals in the highfrequency range during
recording, then lowering
them during playback. Type
C provides greater noise
reduction than type B.
z You can connect the
headphones to PHONES
(TC-WE405 only)
* Dolby noise reduction
manufactured under license
from Dolby Laboratories
Licensing Corporation.
“DOLBY“ and the double-D
symbol a are trademarks of
Dolby Laboratories Licensing
Corporation.
Turn on the amplifier and select the tape deck position.
1
Press POWER, and then press §
2
and insert a cassette.
With the side you want to play
facing you
Set DIRECTION.
3
To play back Set to
One side only A
Both sides continuously* a
Both decks in succession* RELAY
* The deck automatically stops after playing back five times.
Press ·.
4
The deck starts playing. Adjust the volume on the amplifier.
To
Stop playing p
Start playback from the reverse side ª
Pause (deck B only) PAUSE P. Press the button again to
Fast-forward or rewind ) or 0 when the deck is stopped
Take out the cassette § after stopping playing
Press
resume play.
Basic Operations
EN
5
3-810-312-31(1)
Basic Operations
Basic Operations
Recording on a Tape
234
DECK A DECK B
COUNTER RESET
0
p
)
ª·
§
POWER
DIRECTION
RELAY
Da
SYNCHRO DUBBING A→B
HIGH/NORMAL
START(DECK B P)
PAUSE REC MUTE REC
PrR
0)
p
§
DOLBY NR
OFF B C
FADER ARL
ª·
5
AUTO
REC LEVEL
5
6
4
3
7
2
8
1
9
0
10
PHONES
• See page 4 for hookup
information.
• Use deck B (on your right
hand side) for recording.
• See "Dubbing a Tape" (page
9) to make a copy of the
tape.
Note
When deck B is recording or in
recording pause, all buttons on
deck A do not work.
Turn on the amplifier and play the program source you want
1
to record.
Press POWER, and then press § and
2
insert a cassette into deck B.
With the side you want to record
facing you
Set DIRECTION.
3
To record on
Set to
Only one side A
Both sides* a
* Recording stops when the tape reaches the end of reverse side.
Press REC r.
4
· lights up for recording on the side facing you. If it doesn’t,
press · once.
The tape deck automatically adjusts the recording level
(see page 8). After the AUTO indicator lights up continuously,
stop playing the program source. If you wish to adjust the
recording level manually, see “To adjust the recording level
manually” on page 7.
EN
6
3-810-312-31(1)
Basic Operations
PHONES
POWER
DECK A DECK B
COUNTER RESET
PAUSE REC MUTE REC
START(DECK B P)
SYNCHRO DUBBING A→B
HIGH/NORMAL
FADER ARL
DIRECTION
Da
RELAY
DOLBY NR
OFF B C
AUTO
PrR
0)
p
ª·
§
0
)
p
ª·
§
REC LEVEL
5
4
3
2
1
0
6
7
8
9
10
z To protect recordings
against accidental erasure
Break out the record-protect
tab(s) (see page 11).
z The Dolby HX PRO*
system automatically
works during recording
(TC-WE405 only)
Distortion and noise in the
high-frequency response are
reduced to produce highquality sound that can be
enjoyed even during
playback on other tape decks.
Press PAUSE P or ·.
5
Recording starts.
Start playing the program source.
6
To
Stop recording
Start recording from the reverse side ª twice in Step 5
Pause PAUSE P. Press the button again to
Take out the cassette § after stopping recording
Use these switches (controls) to perform additional
operations
Press
p
resume recording.
DOLBY NR REC LEVEL
Basic Operations
* HX Pro headroom extension
originated by Bang & Olufsen
and manufactured under license
from Dolby Laboratories
Licensing Corporation.
“DOLBY“, the double-D symbol
a and “HX PRO” are
trademarks of Dolby
Laboratories Licensing
Corporation.
To record with the Dolby NR system
Set DOLBY NR to B or C before you start recording.
To adjust the recording level manually
After pressing REC r in Step 4 on page 6, turn
REC LEVEL so that the peak level meters reach
the recommended level for the corresponding
tape type. After completing the adjustment, stop
playing the program source, then continue the
procedure from Step 5.
–10–20–
30
–
∞
dB
L
R
For type I or
type II tape
For type IV tape
4
8
EN
7
+
+40
–
3-810-312-31(1)
Advanced Recording Operations
Advanced Recording Operations
Adjusting the Recording Level Automatically (Auto Rec Level)
The Auto Rec Level function automatically measures
the peak signal level and adjusts the recording level
accordingly.
PAUSE P REC r·
AUTO
REC LEVEL
DIRECTION
DOLBY NR
RELAY
OFF B C
FADER ARL
PrR
0)
p
ª·
§
5
6
4
3
7
2
8
1
9
0
10
PHONES
Da
SYNCHRO DUBBING A→B
HIGH/NORMAL
START(DECK B P)
DECK A DECK B
COUNTER RESET
0
)
POWER
p
ª·
§
PAUSE REC MUTE REC
1 Follow Steps 1 to 3 of “Recording on a Tape” on
page 6.
Make sure that record-protect tabs on the cassette
have not been removed.
2 Press REC r.
The AUTO indicator flashes and the deck
automatically adjusts the recording level. The
AUTO indicator lights up continuously after the
recording level has been adjusted.
3 Press PAUSE P or ·.
Recording starts.
To cancel the Auto Rec Level function
Press ARL or turn REC LEVEL so that the AUTO indicator
goes off. If you do either of these during recording,
recording will continue but with the Auto Rec Level function
turned off.
z You should adjust the recording level manually with
REC LEVEL in the following cases:
—The recording level cannot be adjusted properly due
to excessive noise in the program source.
—The program source level is too low and the recording
level does not increase.
During a quiet passage in a program source such as
classical music, the recording level may not increase
for some time. If a high sound level is expected later
on in the track, play that portion first so that the right
adjustment can be obtained.
—The recording level does not decrease for a long time.
The Auto Rec Level function may not work properly
when you try to record sound produced by a graphic
equalizer that has extremely high-level signals.
z To record with the optimum recording level
• To prevent changes in the recording level after
recording starts, press REC r while playing the
highest sound level portion of the program source to
be recorded. The result is a more natural-sounding
recording.
• If you play the entire program source after the AUTO
indicator has stopped flashing and is lit continuously,
the deck will set the recording level for the portion of
the program source with the highest signal level.
z Recording level setting remains even after the
recording has ended
After you have finished recording with the Auto Rec
Level function, the AUTO indicator remains on and the
recording level setting remains the same. To cancel the
setting, do one of the following:
• Press ARL to turn off the AUTO indicator
• Turn REC LEVEL
• Turn the deck off.
To stop recording
Press p.
z What is the Auto Rec Level function?
The Auto Rec Level function automatically sets the
recording level according to the peak signal level of the
program source. While the AUTO indicator is flashing,
the deck sets the recording level as high as possible
without causing distortion. If the signal level rises
excessively after the start of recording, the deck
gradually decreases the recording level.
EN
8
3-810-312-31(1)
Advanced Recording Operations
Fading In and Out (Fader)
You can gradually increase the recording level at the
beginning of a recording (fade in) or gradually
decrease the recording level at the end of a recording
(fade out).
It is convenient to use this function, for example, when
the tape reaches to its end and you don’t want the track
to be cut off abruptly.
You can do fade in or out recording only when you
have adjusted the recording level manually
(see page 7).
FADER
AUTO
REC LEVEL
DIRECTION
DOLBY NR
RELAY
OFF B C
FADER
PrR
0)
ª·
5
6
4
3
7
2
8
ARL
1
9
0
10
PHONES
Da
SYNCHRO DUBBING A→B
HIGH/NORMAL
START(DECK B P)
DECK A DECK B
COUNTER RESET
0
)
POWER
p
ª·
§
PAUSE REC MUTE REC
p
§
To Do the following:
Fade in 1 Follow Steps 1 to 4 of “Recording on a
Fade out Press FADER when you want to start
Tape” on page 6.
2 Press FADER. During fade-in, the
AUTO indicator flashes, then goes off
when the fade-in has completed.
fading out while recording. When the
fade-out has completed, “REC” flashes
in the display and the deck pauses.
Note
Fade-in or fade-out is not possible when REC LEVEL is set to
0 (minimum).
Dubbing a Tape
You can copy a tape in deck A to a tape in deck B at
normal or high speed.
p
PAUSE P
DECK A DECK B
COUNTER RESET
0
)
POWER
p
ª·
§
1 Insert the recorded cassette into deck A and a
blank cassette into deck B.
Make sure the record-protect tabs on the cassette
in deck B have not been removed.
2 Select the side(s) to be recorded on.
To record on
One side A
Both sides a.
3 Select the dubbing speed.
To select
Normal speed
High speed
HIGH / NORMAL
DIRECTION
DIRECTION
RELAY
Da
SYNCHRO DUBBING A→B
HIGH/NORMAL
FADER ARL
START(DECK B P)
PAUSE REC MUTE REC
PrR
0)
p
§
Set DIRECTION to
Recording on the reverse side on
deck B starts independently of
playback on deck A.
RELAY.
Recording on the reverse side on
deck B starts simultaneously with
playback of the reverse side on
deck A.
Press HIGH/NORMAL
Once
Twice
DOLBY NR
OFF B C
ª·
ª / ·
AUTO
REC LEVEL
5
6
4
3
7
2
8
1
9
0
10
PHONES
“HIGH” or “NORM” appears in the display.
The tape deck changes to dubbing standby.
4 Select the side from which to start dubbing.
To record from
The front side ·
The reverse side ª
Press
5 Press PAUSE P to start dubbing.
To stop dubbing
During
Normal-speed dubbing
High-speed dubbing
Press
p on deck B
p on either deck
3-810-312-31(1)
EN
9
Advanced Recording Operations
PHONES
POWER
DECK A DECK B
COUNTER RESET
PAUSE REC MUTE REC
START(DECK B P)
SYNCHRO DUBBING A→B
HIGH/NORMAL
FADER ARL
DIRECTION
Da
RELAY
DOLBY NR
OFF B C
AUTO
PrR
0)
p
ª·
§
0
)
p
ª·
§
REC LEVEL
5
4
3
2
1
0
6
7
8
9
10
PAUSE P REC MUTE R·
z During high-speed dubbing
Only p is operative.
Inserting a Blank Space During
z You don‘t have to adjust the recording level or
select the Dolby NR system during dubbing
Dubbing is automatically performed with the same
recording level and Dolby NR system as the original in
deck A. If, however, you want to monitor the sound
during normal-speed dubbing, set DOLBY NR to match
the tape in deck A (see page 5).
Note
If a TV set is placed near the tape deck, noise may occur
during high-speed dubbing. In that case, turn the television
set off or move it away from the tape deck.
Dubbing only specific portions
You can do this only during the normal-speed
dubbing.
1 Press p on deck A at the portion you want to
skip.
Deck B changes to recording pause.
2 Locate the point you want to resume recording on
deck A, then stop the tape.
Recording (Record Muting)
You can insert a blank space of 4 seconds between each
track or erase unwanted portions on a tape.
1 Start recording.
2 Press REC MUTE R where you want to insert a
blank space.
“REC” flashes in the display and a blank is
recorded on the tape.
After 4 seconds, P lights up and the tape deck
changes to recording pause.
3 Press PAUSE P or · to resume recording.
3 Press PAUSE P to resume dubbing.
z If you want to insert a blank space longer than 4
seconds
Hold down REC MUTE R as long as you want. After 4
seconds, “REC” flashes faster.
When you release REC MUTE R, P lights up and the
tape deck changes to recording pause.
Press PAUSE P or · to resume recording.
EN
10
3-810-312-31(1)
Additional Information
Specifications
General
Power requirements
System
Recording system
4-track 2-channel stereo
Fast-winding time (approx.)
180 sec. (with Sony C-60 cassette)
Bias
AC bias
Signal-to-noise ratio (at peak level and weighted with Dolby NR off)
Type I tape, Sony Type I (NORMAL): 55 dB
Type II tape, Sony Type II (HIGH): 57 dB
Type IV tape, Sony Type IV (METAL): 58 dB
S/N ratio improvement (approximate values)
With Dolby B NR on: 5 dB at 1 kHz, 10 dB at 5 kHz
With Dolby C NR on: 15 dB at 500 Hz, 20 dB at 1 kHz
Harmonic distortion
0.4% (with Type I tape, Sony Type I (NORMAL):
160 nWb/m 315 Hz, 3rd H.D.)
1.8% (with Type IV tape, Sony Type IV (METAL):
250 nWb/m 315 Hz, 3rd H.D.)
Frequency response (Dolby NR off)
Type I tape, Sony Type I (NORMAL): 30 - 16,000 Hz
(±3 dB, IEC)
Type II tape, Sony Type II (HIGH): 30 - 17,000 Hz
(±3 dB, IEC)
Type IV tape, Sony Type IV (METAL): 30 - 19,000 Hz
(±3 dB, IEC)
30 - 13,000 Hz (±3 dB, –4 dB recording)
Type I tape, Sony Type I (NORMAL): 20 - 17,000 Hz
(±6 dB)
Type II tape, Sony Type II (HIGH): 20 - 18,000 Hz
(±6 dB)
Type IV tape, Sony Type IV (METAL): 20 - 20,000 Hz
(±6 dB)
Where purchased Power requirements
U.S.A. and Canada 120 V AC, 60 Hz
U.K. and Continental Europe 220 - 230 V AC, 50/60 Hz
Australia 240 V AC, 50/60 Hz
Other countries 120/220/240 V AC,
Power consumption
50/60 Hz
18 W
Dimensions (approx) (w/h/d)
430 × 120 × 305 mm (w/h/d)
(17 × 4 3/
4 × 12
1
/
8 inches)
including projecting parts and controls
Mass (approx.)
3.8 kg (8 lbs 7 oz)
Supplied accessories
Audio connecting cords (2 phono plugs - 2 phono
plugs) (2)
Optional accessory
Remote commander RM-J910
For more information on the availability of the remote
commander, contact your nearest Sony dealer.
Design and specifications are subject to change without
notice.
14
Wow and flutter
±0.15% W. Peak (IEC)
0.1% W. RMS (NAB)
±0.2% W. Peak (DIN)
Inputs
Line inputs (phono jacks)
Sensitivity : 0.16 V
Input impedance : 47 kilohms
Outputs
Line outputs (phono jacks)
Rated output level : 0.5 V at a load impedance of
47 kilohms
Load impedance : Over 10 kilohms
Headphones (stereo phone jack) (TC-WE405 only)
Output level : 0.25 mW at a load impedance of
32 ohms
EN
3-810-312-31(1)
Index
Index
A, B
Adjusting
recording level automatically. See Auto rec
level
recording level manually 7
volume 5
Audio connecting cord 4, 14
Auto play 5
Auto rec level 8
C
Cassette. See Tape
Cleaning
cabinet 11
heads and tape path 12
Connecting. See Hooking up
D, E, F, G
Dolby HX PRO system 7
Dolby NR system 5, 7
Dubbing
high-speed dubbing 9
normal-speed dubbing 9, 10
only specific portions 10
Fader 9
Fading
in. See Fader
out. See Fader
H, I, J, K, L, M, N, O
Heads
cleaning 12
demagnetizing 12
Hooking up
hookups 4
overview 4
Insert
blank space 10
cassette 5, 6
Index
Names of Controls
Buttons
ARL (automatic recording level adjustment) 8
FADER 9
HIGH/NORMAL 9
PAUSE P 5, 7 - 10, 13
REC (recording) r 6 - 8
REC MUTE (record muting) R 10
§ (eject) 5 - 7, 12, 13
p (stop) 5, 7 - 10, 13
· (forward play) 5 - 10, 13
ª (reverse play) 5, 7, 9, 13
), 0 (fast-forwarding and rewinding) 5, 13
Switches
DIRECTION 5, 6, 9
DOLBY NR 5, 7, 10, 13
POWER 5, 6
Controls
REC (recording) LEVEL 7 - 9
Jacks
LINE IN 4
LINE OUT 4
PHONES 5
Others
AUTO indicator 6, 8, 9
Cassette holder 5, 6, 12
Peak level meters 7
P, Q, R, S
Playing
auto play 5
basic play 5
Recording 6
Record muting 10
Specifications 14
T, U, V, W, X, Y, Z
Tape
ejecting 5, 7
notes 11
path cleaning 12
protect the recording 11
type 11
Troubleshooting 13
Unpacking 4
3-810-312-31(1)
15
EN
AVERTISSEMENT
Afin d’éviter tout risque
d’incendie ou
d’électrocution, ne pas
exposer cet appareil à la
pluie ou à l’humidité.
F
2
3-810-312-31(1)
Bienvenue!
Merci pour l’achat de cette platine à
cassette stéréo Sony. Avant de la mettre
en service, veuillez lire attentivement ce
mode d’emploi et le conserver pour
toute référence future.
A propos de ce
Table des matièr es
Préparatifs
Déballage 4
Raccordement de la platine 4
Lecture d’une cassette 5
Enregistrement sur une cassette 6
manuel
Les instructions de ce mode d’emploi
concernent les modèles TC-WE405 et
TC-WR661. Vérifiez le numéro de votre
modèle sur le panneau arrière de la
platine. Les illustrations de ce mode
d’emploi représentent le TC-WE405.
Toute différence de fonctionnement est
clairement indiquée dans le texte, par
exemple “TC-WE405 uniquement”.
Type de différences
Modèle WR661WE405
Fonction
Dolby HX PRO
Prise PHONES
Convention
Le symbole suivant est utilisé dans ce
mode d’emploi:
Indique des conseils et des
suggestions qui facilitent une
z
manipulation.
•
•
Fonctions élaborées pour l’enregistrement
Réglage automatique du niveau d’enregistrement (fonction d’autoréglage du son) 8
Fondu à l’ouverture et fondu à la fermeture (Fader) 9
Copie d’une cassette 9
Insertion d’un espace vierge pendant l’enregistrement
(Silencieux d’enregistrement) 10
Informations complémentaires
Précautions 11
Remarques sur les cassettes 11
Nettoyage 12
En cas de panne 13
Spécifications 14
Index 15
F
3-810-312-31(1)
F
3
Ç
ç
REC OUT IN
LINE
OUTIN
L
R
TAPE
L
R
L
R
Préparatifs
Déballage
Vérifiez si les éléments suivants se trouvent bien dans
l’emballage:
• Cordons de liaison audio (2)
Raccordement de la platine
Cette partie explique comment raccorder la platine à
l’amplificateur. N’oubliez pas d’éteindre les deux
appareils avant de les raccorder.
Pour les acheteurs du TC-WR661
Consultez le mode d’emploi de l’amplificateur TA-AV561
pour le raccordement de votre platine à cassette à cet
appareil.
Raccordements
Quand vous branchez un cordon de liaison audio,
vérifiez la couleur de la prise et celle de la fiche du
cordon: Fiche rouge (droite) dans la prise rouge et
fiche blanche (gauche) dans la prise blanche. Veillez à
bien enfoncer les fiches pour éviter tout ronflement ou
bruit.
Raccordez la platine à l’amplificateur comme indiqué
ci-dessous.
Platine à cassette Amplificateur
Pour les acheteurs du TC-WE405
Suivez les instructions ci-dessous pour raccorder votre
platine à cassette à un amplificateur.
TC-WE405
vers LINE IN
vers REC OUT
vers LINE OUT
vers TAPE IN
vers une prise
secteur
Amplificateur
vers une prise
murale
ç: Flux du signal
Réglage du sélecteur de tension
(uniquement pour les modèles avec
sélecteur de tension)
Vérifiez que le sélecteur de tension sur le panneau
arrière de la platine à cassette est réglé sur la tension
du secteur local. Si ce n’est pas le cas, réglez-le sur la
position correcte avec un tournevis avant de brancher
le cordon d’alimentation secteur sur une prise secteur.
VOLTAGE
220V
240V
120V
Branchement du cordon d’alimentation
secteur
Branchez le cordon sur une prise secteur.
Que faire ensuite?
Maintenant la platine à cassette est prête.
Pour les fonctions de base, voir pages 5 à 7; pour les
fonctions élaborées, voir les paragraphes à partir de la page 8.
F
4
3-810-312-31(1)
Fonctionnement de base
Lecture d’une cassette
24 3
Da
SYNCHRO DUBBING A→B
START(DECK B P)
POWER
DECK A DECK B
COUNTER RESET
0
)
p
ª·
§
DIRECTION
OFF B C
RELAY
HIGH/NORMAL
FADER ARL
PAUSE REC MUTE REC
PrR
0)
p
ª·
§
DOLBY NR
AUTO
REC LEVEL
5
6
4
3
7
2
8
1
9
0
10
PHONES
• Voir page 4 pour le
raccordement.
• Vous pouvez utiliser les deux
platines pour la lecture.
z Pour localiser le début
d’une bande et
commencer la lecture
automatiquement (Auto
Play)
Appuyez sur 0 tout en
maintenant · enfoncé. Pour
la face arrière, appuyez sur
) en maintenant ª
enfoncé.
z Pour écouter une cassette
avec le système de
réduction de bruit Dolby*
Sélectionnez pour DOLBY
NR le même réglage - B ou C
- que lors de l’enregistrement
de la cassette.
z Qu’est-ce que le système
de réduction de bruit
Dolby?
Le système de réduction
Dolby élimine le ronflement
en accentuant les signaux de
basses fréquences sur la
plage de hautes fréquences
pendant l’enregistrement,
puis en les réduisant pendant
la lecture. Le type C assure
une réduction du bruit
supérieure à celle du type B.
z Vous pouvez brancher le
casque sur PHONES (TCWE405 uniquement)
* Réduction de bruit Dolby
fabriquée sous licence de Dolby
Laboratories Licensing
Corporation.
DOLBY et le symbole double-D
a sont des marques de Dolby
Laboratories Licensing
Corporation.
Allumez l’amplificateur et sélectionnez la fonction platine.
1
Appuyez sur POWER puis sur § et introduisez une cassette.
2
Tournez la face à lire vers vous.
Réglez DIRECTION.
3
Pour reproduire Réglez sur
Une face seulement A
Les deux faces continuellement* a
Les deux platines successivement* RELAY
* La platine s’arrête automatiquement au bout de cinq lectures
consécutives.
Appuyez sur ·.
4
La lecture commence. Réglez le volume sur l’amplificateur.
Appuyez surPour
Arrêter la lecture p
Démarrer la lecture sur la face arrière ª
Faire une pause (platine B uniquement) PAUSE P. Appuyez une nouvelle fois
sur cette touche pour poursuivre la
lecture.
Avancer rapidement ou rebobiner la
bande
Sortir la cassette § après avoir arrêté la lecture
) ou 0 quand la platine est arrêtée
Fonctionnement de base
F
5
3-810-312-31(1)
Fonctionnement de base
Fonctionnement de base
Enregistrement sur une cassette
234
AUTO
REC LEVEL
DOLBY NR
POWER
DECK A DECK B
COUNTER RESET
0
)
p
ª·
DIRECTION
OFF B C
RELAY
Da
SYNCHRO DUBBING A→B
HIGH/NORMAL
FADER ARL
START(DECK B P)
PAUSE REC MUTE REC
PrR
0)
p
ª·
§
§
5
6
4
3
7
2
8
1
9
0
10
PHONES
5
• Voir page 4 pour le
raccordement.
• Utilisez la platine B (côté
droit) pour l’enregistrement.
• Voir “Copie d’une cassette”
(page 9) pour copier une
cassette.
Remarque
Quand la platine B enregistre ou
est en pause d’enregistrement,
toutes les touches de la platine A
sont inopérantes.
Allumez l’amplificateur et reproduisez la source de
1
programme que vous voulez enregistrer.
Appuyez sur POWER puis sur §, et introduisez
2
une cassette dans la platine B.
Tournez la face à enregistrer
vers vous.
Réglez DIRECTION.
3
Pour enregistrer sur
Réglez sur
Une face seulement A
Les deux faces* a
* L’enregistrement s’arrête quand la face arrière est finie.
Appuyez sur REC r.
4
· s’allume pour indiquer que l’enregistrement commence sur
la face tournée vers vous. Si ce n’est pas le cas, appuyez une
fois sur ·.
La platine à cassette ajuste automatiquement le niveau
d’enregistrement (voir page 8). Après l’allumage de
l’indicateur AUTO, arrêtez la source de programme. Si vous
souhaitez ajuster le niveau d’enregistrement manuellement,
voir “Pour ajuster manuellement le niveau d’enregistrement”
(page 7).
F
6
3-810-312-31(1)
PHONES
POWER
DECK A DECK B
COUNTER RESET
PAUSE REC MUTE REC
START(DECK B P)
SYNCHRO DUBBING A→B
HIGH/NORMAL
FADER ARL
DIRECTION
Da
RELAY
DOLBY NR
OFF B C
AUTO
PrR
0)
p
ª·
§
0
)
p
ª·
§
REC LEVEL
5
4
3
2
1
0
6
7
8
9
10
Fonctionnement de base
–
4
L
R
–
∞
+
8
dB
+40
–10–20–
30
z Pour protéger vos
enregistrements contre un
effacement accidentel
Brisez la ou les languettes de
protection (voir page 11).
z Le système Dolby HX
PRO* s’active
automatiquement
pendant l’enregistrement
(TC-WE405 uniquement)
La distorsion et le bruit sont
réduits dans la réponse de
hautes fréquences pour
produire un son de haute
qualité dont on pourra
profiter même pendant la
lecture sur d’autres platines à
cassette.
Appuyez sur PAUSE P ou ·.
5
L’enregistrement commence.
Démarrez la source de programme.
6
Pour
Arrêter l’enregistrement
Démarrer l’enregistrement sur la face
arrière
Faire une pause
Sortir la cassette
Utilisez aussi les sélecteurs et interrupteurs (commandes)
suivants
Pour enregistrer avec le système de réduction de bruit Dolby
Réglez DOLBY NR sur B ou C avant de commencer l’enregistrement.
Appuyez sur
p
ª deux fois à l’étape 5
PAUSE P. Appuyez une nouvelle fois
sur cette touche pour poursuivre
l’enregistrement.
§ après avoir arrêté l’enregistrement
DOLBY NR REC LEVEL
Fonctionnement de base
* HX Pro headroom extension
d’origine Bang & Olufsen et
fabriqué sous licence de Dolby
Laboratories Licensing
Corporation.
DOLBY, le symbole double-D
a et HX PRO sont des marques
de Dolby Laboratories Licensing
Corporation.
Pour ajuster manuellement le niveau d’enregistrement
Après la pression de REC r à l’étape 4 de la
page 6, tournez REC LEVEL de sorte que les
décibelmètres atteignent le niveau
recommandé pour le type de cassette utilisée.
Une fois ces réglages effectués, arrêtez la source de
programme et continuez la procédure à partir de
l’étape 5.
pour une
cassette de
type I ou II
pour une
cassette de type
IV
3-810-312-31(1)
F
7
Loading...