Sony TAFE-600-R Service manual
TA-FE600R
SERVICE MANUAL
SPECIFICATIONS
AEP Model
MICROFILM
+0
–3
INTEGRATED STEREO AMPLIFIER
— 1 —
TABLE OF CONTENTS
1. GENERAL .................................................................... 3
2. ELECTRICAL ADJUSTMENT .......................................4
3. DIAGRAMS
3-1. Circuit Boards Location .......................................................5
3-2. IC Pin Function
• IC902 Input Control LED Driver
(TMP47C103N-JP47) .......................................................6
3-3. Schematic Diagram — Panel Section —..............................7
3-4. Printed Wiring Board — Panel Section — ........................... 9
3-5. Schematic Diagram — Main Section — ............................ 12
3-6. Printed Wiring Board — Main Section — ......................... 15
4. EXPLODED VIEWS
4-1. Front Panel Section ............................................................ 19
4-2. Chassis Section...................................................................20
5. ELECTRICAL PARTS LIST ..................................... 21
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK ! OR DO TTED LINE
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
— 2 —
LOCATION OF PARTS AND CONTROLS
FRONT PANEL
SECTION 1
GENERAL
This section is extracted from
instruction manual.
1
1 POWER switch
2 INPUT SELECTOR indicator
3 SUBSONIC switch
4 EON LINK switch
5 EON LINK indicator
6 VOLUME control
7 SOURCE DIRECT indicator
8 SOURCE DIRECT switch
9 INPUT SELECTOR control
23
5467890!¡!™!£!¢!∞!§!¶
0 TAPE 1 MONITOR indicator
!¡ TAPE 1 MONITOR switch
!™ LOUDNESS switch
!£ BALANCE control
!¢ TONE (BASS, TREBLE) control
!∞ SPEAKERS selector
!§ Remote control sensor
!¶ PHONES jack
REAR PANEL
12 34
567 9
0!¡
!™
— 3 —
SECTION 2
ELECTRICAL ADJUSTMENT
Bias Adjustment
1. Rotate fully the bias adjusting semi-fixed resistors (R V301, RV351)
to the MIN position (counterclockwise).
2. Connect a digital voltmeter to the CN406 and CN407.
1 pin 3 pin
CN406
CN407
–
+
3. Set the slide r egulator to 0V, and press the POWER button (ON)
on the set.
4. Raise gradually the slide regulator voltage up to the rated voltage (230 V).
5. At this time, confirm that the SP relay is turned on (it will click).
6. Adjust the RV301 and R V351 so that a reading of digital voltmeter
is 10 mV to 15 mV.
7. Return the slidack to 0 V, and press the POWER button (OFF) on
the set.
+
–
Adjustment Location :
[MAIN A BOARD] — COMPONENT SIDE —
‘
RV301
RV351
‘
C322 C372
BIAS
Adjustment
Test Point Location :
[MAIN B BOARD] — COMPONENT SIDE —
CN406
1
C409 C459
CN407
3
+
–
DIGITAL
VOLTMETER
3
1
+
–
DIGITAL
VOLTMETER
— 4 —
3-1. CIRCUIT BOARDS LOCATION
SECTION 3
DIAGRAMS
PANEL board
MAIN B board
TRANS board
LED board
OUTLET board
INPUT board
MAIN A board
PRO IND board
HP board
SP TM board
SP SW board
VOL board
EON board
— 5 —
3-2. IC PIN FUNCTION
• IC902 Input Control LED Drive (TMP47C103N-JP47)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
X OUT
X IN
RESET
PMD
VOL +
VOL –
SW 0
SW 1
SW 2
EON
PHONO
TUNER
CD
GND
AUX
DA T
TAPE
MON
PRY
PKY
MON
SIRCS
MUTE
SCE
SDT
SCK
STOP
+3V
Pin Name
I/O
O
System clock. (4MHz)
I
Reset input.
I
Mode select input.
I
Motor drive output (+).
O
Motor drive output (–).
O
Rotary switch input (CD).
I
Rotary switch input (TUNER).
I
Rotary switch input (PHONO).
I
EON signal input.
I
PHONO LED drive output.
O
TUNER LED drive output.
O
CD LED drive output.
O
Ground.
—
AUX LED drive output.
O
TAPE “2” LED drive output.
O
TAPE “1” LED drive output.
O
MONITOR output.
O
Power relay output.
O
Power key input.
I
MONITOR input.
I
SIRCS input.
I
Muting output.
O
Chip enble output.
O
Serial data output.
O
Serial clock output.
O
STOP input.
I
+3V Power supply.
—
Function
— 6 —
Loading...