Sony SRS-XE300 Users guide

5-037-896-42(1)

Wireless Speaker

Reference Guide

SRS-XE300

©2022 Sony Corporation
Printed in China
https://www.sony.net/

English Wireless Speaker

Do not expose the unit to naked flame sources (for example, lighted candles).

Do not install the product in a confined space, such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or batteries installed) to excessive heat, such as sunshine, fire
or the like, for a long time.

This unit has been tested and found to comply with the limits set out in the EMC regulation using a
connection cable shorter than 3 m.

The nameplate and important information concerning safety are attached in the following locations:

• the back of the cap on the rear side of the unit.

Do not dismantle, open or shred secondary cells or batteries.

Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight.

In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact
has been made, wash the affected area with copious amounts of water and seek medical advice.

Secondary cells and batteries need to be charged before use. Always refer to the manufacturer’s
instructions or product manual for proper charging instructions.

After extended periods of storage, it may be necessary to charge and discharge the cells or batteries
several times to obtain maximum performance.

Dispose of properly.

This product (including accessories) has magnet(s) which may interfere with pacemakers, programmable
shunt valves for hydrocephalus treatment, or other medical devices. Do not place this product close to
persons who use such medical devices. Consult your doctor before using this product if you use any
such medical device.

Never insert the USB plug when the main unit or charging cable is wet. If the USB plug is inserted while
the main unit or charging cable is wet, a short circuit may occur due to liquid (tap water, seawater, soft
drink, etc.) or foreign matter on the main unit or charging cable, and cause abnormal heat generation or
malfunction.

This product must be installed and operated with at least 20 cm separation between the radiating
element and the human body (excluding extremities: hands, wrists, feet and ankles).

Licenses

• This product contains software that Sony uses under a licensing agreement with the owner of its
copyright. We are obligated to announce the contents of the agreement to customers under
requirement by the owner of copyright for the software. Please access the following URL and
read the contents of the license.
https://rd1.sony.net/help/speaker/sl/22/

• The software included in this product contains copyrighted software that is licensed under the
GPL/LGPL and other licenses which may require access to source code. You may find a copy of
the relevant source code as required under the GPL/LGPL (and other licenses) at the following
URL.
You may obtain the source code as required by the GPL/LGPL on a physical medium from us for a
period of three years after our last shipment of this product by applying through the form at the
following URL.
This offer is valid to anyone in receipt of this information.
https://oss.sony.net/Products/Linux/
Please note that Sony cannot answer or respond to any inquiries regarding the content of this
source code.

• Use of the Made for Apple badge means that an accessory has been designed to connect
specifically to the Apple product(s) identified in the badge, and has been certified by the
developer to meet Apple performance standards. Apple is not responsible for the operation of
this device or its compliance with safety and regulatory standards.

Disclaimer regarding services offered by third parties

• Services offered by third parties may be changed, suspended, or terminated without prior notice.
Sony does not bear any responsibility in these sorts of situations.

Notes on waterproof and dustproof features

(Read before using the unit)

The supplied accessories are neither waterproof nor dustproof.

Waterproof and dustproof performance of the unit

The unit, with the cap fastened securely, has a waterproof specification of IPX7 as specified in “Degree of
protection against water immersion” of the IEC60529 “Ingress Protection Rating (IP Code)”, and a
dustproof specification of IP6X as specified in “Degrees of protection against solid foreign objects”.

• The supplied accessories and the connectors of this unit (USB) are neither water resistant nor
dustproof. To reduce the risk of fires or electric shocks, do not expose the unit to water or droplets
while using any connectors (USB) .

Note that malfunctions as a result of water immersion or dust intrusion caused by misuse by the
customer are not covered by the warranty.

To avoid the deterioration of waterproof and dustproof
performance

Carefully note the precautions below to ensure proper use of the unit.

• The unit passes the drop test from 1.22 m on plywood of 5 cm thickness conforming to MIL-STD810H
Method 516.8-Shock. However, this does not guarantee no damage, no breakdown, or waterproof and
dustproof performance in all conditions. Deformation or damage from dropping the unit or subjecting
it to mechanical shock may cause deterioration of the waterproof and dustproof performance.

• This unit does not have a design that is resistant to water pressure. Use of the unit in a location where
high water pressure is applied, such as in the shower, may cause a malfunction.

• Do not pour high-temperature water or blow hot air from a hair dryer or any other appliance on the
unit directly. Also never use the unit in a place subject to high temperatures, such as in a sauna or
near a heat source.

CAUTION : Handle the cap with care. The cap plays a very important role in maintenance of the

water resistant and dustproof performance. When using the unit, make sure that the cap is closed
completely. When closing the cap, be careful not to allow foreign objects inside. If the cap is not closed
completely the water resistant and dustproof performance may deteriorate and may cause a
malfunction of the unit as a result of water or dust particles entering the unit.

Passive
radiator

Cap

How to care for the unit

Although the fabric part of the unit has water repellent treatment applied, you can use the unit
more comfortably and for a longer period of time by following the maintenance procedure below.

• If the surface of the unit gets dirty in the following cases, wash the unit with fresh water (tap water,
etc.) promptly to remove the dirt. Leaving dirt on its surface may cause the surface to discolor or
deteriorate, or the unit to malfunction.
Ex.

– When the unit has sand, salt (chlorine), or other residue on it after having been used in a mountain

area, by a swimming pool, etc.

– When the unit is stained with foreign substances (sunscreen, suntan oil, etc.)

• Wipe off the moisture on its surface, and put the unit on a dry soft cloth to drain the collected water
inside the unit. Then, dry the unit in an airy place until no moisture remains.

• The sound quality may change when water enters the speaker or passive radiator section of the unit.
It is not malfunction. Wipe off the moisture on its surface, and put the unit on a dry soft cloth to drain
the collected water inside the unit. Then, dry the unit in an airy place until no moisture remains.

Note

• If the surface of the unit gets dirty, do not use detergent, thinner, benzine, alcohol, etc. to clean the
unit because it will affect the water repellent function of the fabric part of the unit.

• Especially in cold regions, be sure to wipe off the moisture after using the unit. Leaving moisture on
its surface may cause the unit to freeze and malfunction.

• If sand grains, etc. enter the fabric or other part of the unit, remove them carefully. Never use a
vacuum cleaner, etc. on the unit. It may cause damage of the speaker section or other part of the unit.

Precautions

On placement

• When you carry around the unit, firmly grasp the unit with one hand and put it on the palm of the
other hand to prevent it from slipping off. Otherwise, the unit may cause injuries, damage to the unit
itself, or damage to household contents by slipping off.

• To eliminate the risk of malfunctions, avoid the following locations when placing or leaving this unit.

– A place subject to high temperatures, such as under direct sunlight or lighting equipment, near a

heat source, or in a sauna
– Inside a vehicle with the windows closed (especially in summertime)
– A place subject to excessive dust
– A place subject to strong vibration

• Place this unit on a flat, level surface. When placed on a sloped surface, the unit may fall over or fall off
the surface due to its own vibration, resulting in injuries, malfunctions, or performance degradation.

• Depending on the conditions where this unit is placed, it may fall over or fall off the surface. Do not
leave any valuables near the unit.

• This unit is not anti-magnetic. Keep objects susceptible to magnetism (recorded tapes, watches, cash
cards and credit cards with magnetic coding, etc.) away from the unit. When you carry around the
unit, keep this in mind as well.

Other notes

• Do not use or leave the unit in an extremely cold or hot environment (temperature outside the range
of 5 °C – 35 °C). If the unit is used or left in outside the above range, the unit may automatically stop to
protect internal circuitry.

• If you use this unit for a long time, the temperature of this unit may rise, but it is not a malfunction.

• At high temperature, the charging may stop or the volume may reduce to protect the battery.

• Even if you do not intend to use the unit for a long time, charge the battery to its full capacity once
every 6 months to maintain its performance.

Trademarks

• Android and Google Play are trademarks of Google LLC.

• The LDAC™ name is a trademark of Sony Group Corporation or its affiliates.

• The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and
any use of such marks by Sony Group Corporation and its subsidiaries is under license.

• Apple, the Apple logo, iPhone, iPod and iPod touch are trademarks of Apple Inc., registered in the U.S.
and other countries.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.

• IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under
license.

• USB Type-C® and USB-C® are registered trademarks of USB Implementers Forum.

All other trademarks and registered trademarks are trademarks or registered trademarks of their
respective holders. In this manual, ™ and ® marks are not specified.

Specifications

Speaker

Full range unit Approx. 49 mm × 71 mm (2)
Enclosure type Passive radiator model

BLUETOOTH®

Communication system

Maximum communication range

Frequency band 2.4 GHz band (2.400 0 GHz - 2.483 5 GHz)
Compatible BLUETOOTH profiles*2

Supported codecs*

Corresponding content protection

Transmission range (A2DP)

BLUETOOTH Specification version 5.2

1

Line of sight*

A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
HSP (Headset Profile)
HFP (Hands-free Profile)

3

SBC (Subband Codec)

AAC (Advanced Audio Coding)
LDAC*

SCMS-T

20 Hz - 20 000 Hz (Sampling frequency 44.1 kHz)

approx. 30 m

4

Note

Depending on the network environment, there may be an interruption at the high bitrate transmission.

Microphone

Type MEMS (Micro Electronics Mechanical System) type
Directional characteristic

Effective frequency range

General

Power DC 5 V 3 A (using a commercially-available USB AC adaptor capable of delivering

Lithium-ion battery life (while Battery Care mode*

Time required for charging the built-in rechargeable battery (while Battery Care mode*

Operating temperature

Dimensions (including projecting parts and controls)

Mass Approx. 1.3 kg including battery
Supplied accessories USB Type-C® cable (USB-A to USB-C / Max. 1.5 A)*9 (1)

1

The actual range will vary depending on factors such as obstacles between devices, magnetic fields

*

around a microwave oven, static electricity, reception sensitivity, antenna’s performance, operating
system, software application, etc.

2

BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communications between devices.

*
*3 Codec: Audio signal compression and conversion format
*4 LDAC is an audio coding technology developed by Sony that enables the transmission of

High-Resolution (Hi-Res) Audio content, even over a BLUETOOTH connection.

5

Mode for prolonging the durability life of the built-in rechargeable battery by limiting the charging

*

capacity up to approximately 90%. The unit in this mode is capable of playing for a shorter period of
time than stated.

6

The built-in battery life above is measured using our specified music source. Actual performance time

*

may vary from the listed time due to the volume, songs played, surrounding temperature, and usage
conditions.

7

Time required for the empty battery to be fully charged (100%) while the unit is powered off.

*
*8 Provided that a USB AC adaptor capable of delivering an output current of 1.5 A is used for battery

charging connection.

9

A charging cable exclusively designed for the unit. Do not use the cable for any other purposes.

*

System requirements for charging battery using USB

Using a commercially-available USB AC adaptor capable of delivering an output current of 1.5 A or 3.0 A*
(Use of a USB AC adaptor capable of delivering an output current of 3.0 A reduces the battery charging
time.)

* When using a USB AC adaptor with an output current of 3.0 A, be sure to use a USB Type-C cable that

conforms to the USB standard and supports an output current of 3.0 A.
The supplied USB cable supports an output current of up to 1.5 A.

Compatible iPhone/iPod models

iPhone 13 Pro Max, iPhone 13 Pro, iPhone 13, iPhone 13 mini, iPhone 12 Pro Max, iPhone 12 Pro, iPhone 12,
iPhone 12 mini, iPhone SE (2nd generation), iPhone 11 Pro Max, iPhone 11 Pro, iPhone 11, iPhone XS Max,
iPhone XS, iPhone XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7, iPhone SE,
iPhone 6s Plus, iPhone 6s, iPod touch (7th generation)
(As of November 2021)

The unit is compatible with iOS 10.0 or later.

Design and specifications are subject to change without notice.

Omni directional

100 Hz - 8 000 Hz

an output current of 3.0 A) or, using built-in lithium-ion battery

With playback via a BLUETOOTH connection
Approx. 24 hours*
– Volume level: 34
– STAMINA: on
Approx. 14 hours (default)*
– Volume level: 34
– STAMINA: off
Approx. 5 hours*
– Volume level: 50 (MAX.)
– STAMINA: off

Approx. 5 hours*
(10 minutes of charging provide approximately 70 minutes*

5 °C – 35 °C

Approx. 105 mm × 238 mm × 119 mm (w/h/d)

6

6

7 *8

5

is not activated)

6

6

5

is not activated)

of music playback.)

https://rd1.sony.net/help/speaker/srs-xe300/h_zz/