Sony SRP-X700P User Manual 3

BID SPECIFICATION

FOR

POWERED MIXER / SWITCHER

MODEL NUMBER

SRP-X700P

INSTRUCTIONS:
REMOVE THIS COVER PAGE AND ADD TO REQUESTS FOR QUOTATION AND
PROPOSALS. THE OBJECTIVE OF THIS BID SPECIFICATION IS TO ASSIST YOU IN
CLEARLY SPECIFYING THE SONY PRODUCT IDENTIFIED ABOVE, AND ENSURING
THAT THE BUYER IS WELL INFORMED OF THE HIGH STANDARD OF
PERFORMANCE THAT IS TO BE EXPECTED OF A SONY PRODUCT. THE
INFORMATION IN THIS DOCUMENT IS CURRENT AS OF JUNE 2002. PRODUCT
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

SONY ELECTRONICS INC.

DISPLAY PRODUCTS GROUP

1 SONY DRIVE, MD 3D9
PARK RIDGE, NJ 07656

TEL# [phone], FAX# [phone]

1.0 General Information

The purpose of this information is to provide the specification for a product whose
primary purpose is the signal distribution of audio, video and / or computer
graphics information to audio speakers, video or graphics displays or other
processing devices.

This distribution of these signals is to be accomplished via a rack mountable
signal processing device. This document provides the minimum specifications for
this device.

2.0 Description

This product shall be classified as an audio and video signal processing device.
This device shall be directly compatible with microphone and line level audio
sources, video and computer sources, without the use of external devices to
provide this compatibility.

This device shall employ the use of digital signal processing and control to
ensure maximum flexibility and performance in the system environment.

Encased in a durable metal casing, this device shall employ a shape that allows
for rack mounting in a 19” EIA standard rack, using the included rack mount
capability. The unit shall occupy no more than 3 EIA rack units.

3.0 Source Compatibility / Suitability for Application

This device shall be directly compatible with the following audio sources.

Balanced / Unbalanced microphone sources (Phantom power on or off)
Balanced / Unbalanced line level sources

This device shall be compatible with the following video and computer sources.

NTSC Video (Composite and Y/C)
PAL Video (Composite and Y/C)
PAL-M Video (Composite and Y/C)
PAL-N Video (Composite and Y/C)
SECAM Video (Composite)
Modified NTSC 4.43 (Composite)
Component Video (50 and 60 Hz)
480P (60Hz)
575P (50Hz)
720P (60Hz)
1035I (60 Hz)

1080I (50 and 60 Hz)
VGA Computer Graphics (Modes 1, 2 and 3, 60 - 85 Hz)
VESA 800x600 Computer Graphics (56 - 85 Hz)
VESA 1024 x 768 Computer Graphics (43 – 85 Hz)
VESA 1152 x 864 Computer Graphics (70 – 75 Hz)
SUN 1152 x 900 Computer Graphics (65 – 76 Hz)
VESA 1280 x 1024 Computer Graphics (43 – 60 Hz)
Mac 13” Computer Graphics
Mac 16” Computer Graphics

4.0 User Interface / Controllability Information

Control of this device shall be accomplished through one of the following
methods:

Front panel control
Serial control jack for control by external control systems
Advanced serial control jack for control by external control systems
Parallel (Contact closure) control jack for control by external control systems
USB control jacks for control by computer

All of these control methods shall be standard to the device.

In addition, this device shall be able to control other source and display devices.
This shall be accomplished through one or more of the following methods.

Serial control jacks for control of source devices
Serial control jack for control of projector or display
Advanced serial control jack for control of projector or display

All of these control methods shall also be standard to the device.

The front panel control panel shall allow the operator manual control over setup
and configuration of the device. All functions available for control shall be directly
accessible on individual controls, and metering of various audio signals shall be
possible from independent LED’s.

The serial control jack shall employ the use of a standardized device control
protocol that is commonly accepted and understood by control systems
manufacturers. This control jack shall accept unidirectional serial commands that
provide full control over the device.

The following device functions shall be available for control using this method.

Pass through for any compatible projector or display device from projector or
display device remote from supplying manufacturer