SONY SPP-ID970, SPP-971 Service Manual

SPP-ID970/ID971

SERVICE MANUAL

US Model

SPP-ID970

Ver 1.0 1999. 11

Canadian Model

SPP-ID971

Photo: SPP-ID970

SPECIFICATIONS

General

Frequency band (SPP-ID970) 902 – 928 MHz

Frequency band (SPP-ID971) 923.1 – 927.75 MHz Base unit : 18 µW Handset : 73 µW

Operating channel 30 channels

Dial signal

Tone, 10 PPS (pulse) selectable Supplied accessories

AC power adaptor AC-T127 (1) Telephone line cords (2)

Wall bracket for base unit (1) Rechargeable battery pack BP-T23 (1)

Handset

Power source

Rechargeable battery pack BP-T23 Battery life

Standby : Approx. 7 days Talk : Approx. 6 hours

Dimensions

Approx. 58 × 177 × 46 mm (w/h/d), antenna excluded

(approx. 2 3/8 × 7 × 1 13/16 inches) Antenna: Approx. 72 mm (approx. 2 7/8 inches)

Mass

Approx. 270 g

(approx. 9.5 oz), battery included

Base unit

Power source

DC 9V from AC power adaptor AC-T127

Battery charging time Approx. 12 hours

Dimensions

Approx. 123 × 63 × 225 mm (w/h/d), antenna excluded

(approx. 4 7/8 × 2 1/2 × 8 7/8 inches) Antenna: Approx. 120 mm (approx. 4 3/4 inches)

Mass

Approx. 360 g

(approx. 13 oz), wall bracket excluded

Design and specifications are subject to change without notice.

Notes on Chip Component Replacement

∙Never reuse a disconnected chip component.

∙Notice that the minus side of a tantalum capacitor may be damaged by heat.

CORDLESS TELEPHONE

MICROFILM

– 1 –

4-3. SCHEMATIC DIAGRAM — BASE UNIT SECTION (1/2) —

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.

(In addition to this, the necessary note is printed in each block.)

For schematic diagrams

•All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.

•All resistors are in Ω and 1/4 W or less unless otherwise specified.

•C : panel designation.

•U : B+ Line.

•Power voltage is dc 9 V and fed with regulated dc power supply from external power voltage jack. (BASE UNIT)

•Power voltage is dc 12 V and fed with regulated dc power supply from J1006 with 100 Ω in series. (BASE UNIT)

•Power voltage is dc 3 V and fed with regulated dc power supply from battery terminal. (HANDSET)

•Voltage is dc with respect to ground under no-signal condition.

: Impossible to measure

•Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances.

•Signal path.

N : TX (To Tel Line)

O : RX (From Tel Line)

P : bell

For printed wiring boards

•X : parts extracted from the component side.

• : Carbon pattern.

•z : Through hole.

•b: Pattern from the side which enables seeing.

(The other layer’s patterns are not indicated.)

Caution:

Pattern face side: Parts on the pattern face side seen from the (Side B) pattern face are indicated.

Parts face side: Parts on the parts face side seen from the

(Side A) parts face are indicated.

SPP-ID970/ID971

(Page 23)

– 21 –

– 22 –