![](/html/39/3913/391314abcaab956ad5862cdbbb33d6d3e6c905cdc2ee4a54fc0707df466341de/bg1.png)
4-174-242-17 (1)
Network Camera
Installation Manual
Before operating the unit, please read this manual thoroughly and
retain it for future reference.
SNC-CH180/CH280
2010 Sony Corporation Printed in China
Owner’s Record
The model and serial numbers are located on the camera stand. Record
these numbers in the spaces provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding
this product.
Model No. Serial No.
WARNING
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
WARNING
This installation should be made by a qualified service person and should
conform to all local codes.
WARNING
A readily accessible disconnect device shall be incorporated external to the
equipment.
CAUTION
The rating label is located on the camera stand.
CAUTION for LAN port
For safety reason, do not connect the LAN port to any network devices that
might have excessive voltage.
The LAN port of this unit is to be connected only to the devices whose
power feeding meets the requirements for SELV (Safety Extra Low Voltage)
and complies with Limited Power Source according to IEC 60950-1.
Use IEEE802.3af standard compliant devices.
Power Supply
Caution for U.S.A. and Canada
The SNC-CH180/CH280 operates on 24 V AC or 12 V DC.
The SNC-CH180/CH280 automatically detects the power.
In the USA, this product shall be powered by a UL listed Class 2 Power Supply
Only.
In Canada, this product shall be powered by a CSA Certified Class 2 Power
Supply Only.
Caution for other countries
The SNC-CH180/CH280 operates on 24 V AC or 12 V DC.
The SNC-CH180/CH280 automatically detects the power.
Use a power supply rated 24 V AC or 12 V DC which meets the requirements
for SELV (Safety Extra Low Voltage) and complies with Limited Power Source
according to IEC 60950-1.
For customers in the U.S.A.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
You are cautioned that any changes or modifications not expressly approved
in this manual could void your authority to operate this equipment.
All interface cables used to connect peripherals must be shielded in order to
comply with the limits for a digital device pursuant to Subpart B of Part 15 of
FCC Rules.
For customers in Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
For the customers in Europe
The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minatoku, Tokyo, 108-0075 Japan.
The Authorized Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to the addresses given in
separate service or guarantee documents.
For the customers in Europe, Australia and New Zealand
WARNING
This is a Class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
In the case that interference should occur, consult your nearest authorized
Sony service facility.
This apparatus shall not be used in the residential area.
ATTENTION
The electromagnetic fields at specific frequencies may influence the picture
of the unit.
Notes on Use
Before Use
Do not lift the camera by only holding the cables.
If you find condensation before use, turn on the power after leaving it out for
long enough.
Data and security
You should keep in mind that the images or audio you are monitoring may be
protected by privacy and other legal rights, and the responsibility for making
sure you are complying with applicable laws is yours alone.
Access to the camera is protected only by a user name and the password
you set up. No further authentication is provided by the camera nor should
you presume that any other protective filtering is done by the service. Since
the service is Internet-based, there is a risk that the image or audio you are
monitoring can be viewed or used by a third-party via the network.
SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU
OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR
EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY
DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.
Security configuration is essential for wireless LAN. Should a problem
occur without setting security, or due to the limitation of the wireless LAN
specifications, SONY shall not be liable for any damage, loss of recorded data
or restoration thereof.
Always make a test recording, and verify that it was recorded successfully.
SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT
LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE
OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR
ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.
Always verify that the unit is operating properly before use. SONY WILL NOT
BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY
OTHER REASON WHATSOEVER.
If you lose data by using this unit, SONY accepts no responsibility for
restoration of the data.
Personal information
The images taken by the system using this device can identify individuals
and thus they fall under “personal information” stipulated in the “Act on
the Protection of Personal Information”. Please handle the video data
appropriately according to law.
Information recorded using this product may also be “personal information”.
Upon disposal, transfer, repair, or any other occasion where this product or
storage media is passed on to a third party, practice due care in its handling.
Operating or storage location
Avoid operating or storing the camera in the following locations.
Extremely hot or cold places (Operating temperature: –30°C to +50°C [–22°F to
+122°F])
Close to heating equipment (e.g., near heaters)
Close to sources of strong magnetism
Close to sources of powerful electromagnetic radiation, such as radios or TV
transmitters
Locations subject to strong vibration or shock
Locations subject to steam or high humidity
Locations subject to strong wind, such as high places
Locations where corrosive gas or flammable gas is emitted, or where salt
damage may occur
Camera setting
Don’t touch the PCB board by hand directly.
If the camera do not focus well because of the weather (such as rain), adjust
the focus manually.
Ventilation
To prevent heat buildup, do not block air circulation around the camera.
Transportation
Always turn off the power when carrying.
When transporting the camera, repack it as originally packed at the factory or
in materials of equal quality.
Using in cold climates
This device is equipped with a built-in heater, which automatically operates
when the internal temperature drops significantly so that the camera can work
even in a low temperature environment (except when in PoE). However, the
heater cannot melt snow or frost on the lens cover or outside cabinet. Make sure
you install this device where the lens will not be exposed to snow.
Starting and closing under low temperature
When started under temperature conditions of −10°C (14°F) or below, the
camera system may not start operating immediately after start-up. In such a case,
the heater starts and raises the internal temperature, starting the camera system.
It may take about two hours for the camera system to start streaming normal
images.
Using the optional SNCA-CFW5* Wireless Card or CF Memory
Card**
The optional SNCA-CFW5* Wireless Card or CF Memory Card** can be used
only when the power is supplied from AC 24 V or DC 12 V.
If the camera is powered by PoE and you want to use the optional
SNCA-CFW5* Wireless Card or CF Memory Card**, you need to first power off
the camera and then restart it with AC 24 V or DC 12 V power supply.
Attach the CF card slot cover securely to the camera.
* SNCA-CFW5 is not available in some countries and areas. For details, contact
your authorized Sony dealer.
** For inquiries regarding verified CF memory cards, contact your authorized
Sony dealer.
About the CF Memory Card
Data on the CF Memory Card may be damaged or deleted in the following cases.
Sony is not responsible for compensation for damage or lost earnings due to
damage or loss of data.
If you remove the CF Memory Card from this device or turn off the power
while the CF Memory Card is being accessed.
If the CF Memory Card is subject to shock.
When the lifetime of the CF Memory Card expires.
(Lifetime may shorten significantly, depending on its use.)
If the CF Memory Card is not set or inserted properly.
Cleaning
Use a blower to remove dust from the lens cover.
Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn
stains can be removed using a soft cloth dampened with a small quantity of
detergent solution, then wipe dry.
Do not use volatile solvents such as alcohol, benzene or thinners as they may
damage the surface finishes.
Note on laser beams
Laser beams may damage image sensors. You are cautioned that the surface of image
sensors should not be exposed to laser beam radiation in an environment where a laser
beam device is used.
Phenomena Specific to Image Sensors
The following phenomena that may occur in images are specific to image
sensors. They do not indicate a malfunction.
White flecks
Although the image sensors are produced with high-precision technologies, fine
white flecks may be generated on the screen in rare cases, caused by cosmic rays,
etc.
This is related to the principle of image sensors and is not a malfunction.
The white flecks especially tend to be seen in the following cases:
- when operating at a high environmental temperature
- when you have raised the gain (sensitivity)
- when using the slow shutter
Aliasing
When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.
About the Supplied Manuals
Installation Manual (this document)
This Installation Manual describes the names and functions of parts and controls
of the Network Camera, gives connection examples and explains how to set up
the camera. Be sure to read the Installation Manual before operating.
User’s Guide (stored in the CD-ROM)
The User’s Guide describes how to set up the camera and how to control the
camera via a Web browser.
After installing and connecting the camera correctly, operate referring to this
User’s Guide.
Using the CD-ROM Manuals
The supplied CD-ROM disc includes the User’s Guides for this unit in PDF format.
Preparations
The Adobe Reader Version 6.0 or higher must be installed on your computer in
order to use the guides stored in the CD-ROM disc.
Note
If Adobe Reader is not installed, it may be downloaded from the following URL:
http://www.adobe.com/
Reading the manual in the CD-ROM
1 Insert the CD-ROM in your CD-ROM drive.
A cover page appears automatically in your Web browser.
If it does not appear automatically in the Web browser, double-click on the
index.htm file on the CD-ROM.
2 Select and click on the manual that you want to read.
This opens the PDF file of the manual.
Clicking an item in the Table of Contents allows you jump to the relevant
page.
Notes
The files may not be displayed properly, depending on the version of Adobe
Reader. In this case, install the latest version, which you can download from
the URL mentioned in “Preparations” above.
If you have lost or damaged the CD-ROM, you can purchase replacement.
Contact your Sony service representative.
Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
Smartphone viewer
This product is equipped with a Smartphone viewer.
With Smartphone viewer, you can display an image from a network camera, pan,
tilt and zoom that camera, on your smartphone.
For more details, see “Smartphone viewer User’s Manual” at the following URL:
http://www.sony.net/ipela/snc
Location and Function of Part
Front
Audio cable (supplied)
The connector with the longer cable (SP) is used for the line output
connector, and the shorter cable (MIC) is used for the microphone/line input
connector.
SP terminal (minijack, monaural)
Connect a commercially available speaker system with a built-in amplifier.
MIC terminal (minijack, monaural)
Connect a commercially available microphone. This jack supports pluginpower microphones (rated voltage: 2.5 V DC).
I/O (Input/Output) cable (supplied)
This cable is provided with a sensor input and two alarm outputs.
The wires of the cable control the following signals.
Color of wire Name
Red Sensor In +
White Sensor In – (GND)
Black Alarm Out 1 +
Yellow Alarm Out 1 –
Brown Alarm Out 2 +
Green Alarm Out 2 –
For details on each function and required settings, see the User’s Guide stored
in the supplied CD-ROM.
For the wiring, see “Connecting the I/O cable.”
Fall-prevention wire rope mounting screw hole
When installing the camera to the ceiling or the wall, secure the supplied fallprevention wire rope to this hole using the supplied screw.
Lens cover
LAN cable (RJ-45) (supplied)
Connect this cable to a hub or computer on the 10BASE-T or 100BASE-TX
network using a network cable (UTP, category 5).
Power input cable (supplied)
Connect this cable to a 24 V AC or 12 V DC power supply system.
You can screw an extension cable in the connector tip attached at the end of
the cable.
BNC cable (supplied)
Outputs a composite video signal.
Note
The output image is mainly used to adjust the view angle, and may not
display correctly, depending on the video format and image size settings.
The image may not display properly in the horizontal and/or vertical plane.
The image may be reduced.
Camera stand
Caution
Take care not to trap the cables between the camera and the ceiling or
the wall. If the cable is trapped, it may cause a fire or electric shock due to
breaking.
Camera
Back
Rating Label (rear side)
This label shows the name of device and its electric rating.
CF card slot cover
To remove the CF card slot cover, with the supplied wrench remove the
two screws on the cover, and then pull out the CF card slot cover from
the back of the camera. When reinstalling the CF card slot cover, be sure
the waterproof washer is at the original place and the cover is completely
closed.
Note
For the sake of waterproof, screw torque should be over 0.4 N•m to
0.5 N•m.
CF card slot
This slot is used for the optional SNCA-CFW5* Wireless Card or CF
Memory Card**.
Note
Insert the CF memory card** with its bottom side facing the camera’s
control panel.
* SNCA-CFW5 is not available in some countries and areas. For details,
contact your authorized Sony dealer.
** For inquiries regarding verified CF memory cards, contact your
authorized Sony dealer.
CF card lever
Press the lever to remove the CF memory card** from the CF card slot.
Control panel cover
Loosen the retaining screw with the supplied wrench and open the cover
in the direction shown by the arrow.
Camera head fixing screw
First loosen the screw with the supplied wrench and face the camera
head to the desired direction, then tighten the screw to fix it.
POWER indicator (Green)
When the power is supplied to the camera, the camera starts checking
the system. If the system is normal, this indicator lights up.
NETWORK indicator (Green/Orange)
The indicator lights up or flashes when the camera is connected to the
network. The indicator is off when the camera is not connected to the
network. When 100BASE-TX is connected, the indicator turns green.
When 10BASE-T is connected, the indicator turns orange.
NTSC/PAL indicator (Green/Orange)
The green indicator lights up when the output mode is NTSC.
The orange indicator lights up when the output mode is PAL.
Heater indicator (Green)
When the power is supplied by AC 24 V or DC 12 V, if the heater in the
camera is working normally , the indicator lights up in green.
When the power is supplied by PoE, the heater will not work. However,
the heater indicator may light up.
NTSC/PAL button
Switching the video output.
MONITOR output jack
Connect this jack to a video input connector of a video monitor. You
can adjust the camera or lens while looking at the image on the video
monitor. After adjusting the camera or lens, disconnect the cable.
Close the cover firmly to keep the camera waterproof.
Note
Use the plug that is 11.8 mm or smaller in diameter.
Zoom buttons
Use the two buttons to adjust lens’ zoom.
[W] WIDE: Zoom out
[T] TELE: Zoom in
Focus buttons
Use the two buttons to adjust lens’ focus.
[N] NEAR: Focus on a nearby subject
[F] FAR: Focus on a distant subject
To reset the camera to its factory default settings, hold down these two
buttons together and supply power to camera.
Easy Focus button
Press this button to automatically adjust the focus easily.
(continued on the reverse side)
Wireless/CF card (not supplied)
![](/html/39/3913/391314abcaab956ad5862cdbbb33d6d3e6c905cdc2ee4a54fc0707df466341de/bg2.png)
Vertical marker
Hole for connecting
cables ø40 (1 5/8)
Hole for installing
the stand
Horizontal maker
Ceiling
When ZOOM/FOCUS switch slides to W/T
The number indicates
the zoom position.
* mark indicates the
approximate zoom position.
When ZOOM/FOCUS switch slides to N/F
The number indicates
the focus position.
* mark indicates the
approximate focus position.
83.7 (3 3/10)
85.7 (3 3/8)
)
10
/
3
83.7 (3
Unit: mm (inches)
Wire rope (supplied)
Screw M4 × 8 (supplied)
Camera mounting
screw (not supplied) (4)
)
8
/
3
85.7 (3
)
2
/
1
139.5 (5
ø140 (5 5/8)
186 (7 3/8)
316.8 (12 1/2)
ø93 (3
)
4
3
/
Unit: mm (inches)
Installation
WARNING
If you attach the camera in the height such as the wall or the ceiling, etc.,
entrust the installation to an experienced contractor or installer.
If you install the camera at a height, ensure that the installation location and
its material are strong enough to withstand a weight of 15 kg (33 lb 1 oz) or
more, and then install the camera securely. If they are not strong enough, the
camera may fall and cause serious injury. If the ceiling is not strong enough,
the camera may fall and cause serious injury.
To prevent the camera from falling, make sure to attach the supplied wire rope.
If you attach the camera to a high location, check periodically, at least once a
year, to ensure that the connection has not loosened. If conditions warrant,
make this periodic check more frequently.
Deciding the Installation Location of the Camera
After deciding the direction in which the camera will shoot, make the required
hole (ø40 mm (1 23/40 inches)) for the connecting cables using the supplied
template. Then decide the four mounting hole positions to install the camera
stand.
Mounting screws
The camera stand is provided with four ø4.5 mm (3/16 inch) mounting holes.
Install the camera stand on a ceiling or wall with screws through four mounting
holes: The required mounting screws differ depending on the installation
location and its material. (Mounting screws are not supplied.)
Steel wall or ceiling: Use M4 bolts and nuts.
Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be
15 mm (5/8 inch) or more.
Concrete wall: Use anchors, bolts and plugs suitable for concrete walls.
Junction box: Use screws to match the holes on the junction box.
WARNING
The required mounting screws differ depending on the installation location and
its material. If you do not secure the camera with the appropriate mounting
screws, the camera may fall off.
Installing the Camera
1 Pass all the signal cables through the hole for the cables made at the
installing surface.
2 Fix the supplied wire rope to the camera unit and the ceiling or wall.
Fix the wire rope with the supplied Screw M4 × 8 to the hole for the
wire rope on the camera stand.
Fix the wire rope to the ceiling or wall.
3 Install the camera on the ceiling or wall
Insert the four screws to the screw holes on the camera stand, and then
tighten the screws to attach the camera.
When installing the camera on the wall, be sure the TOP mark on the camera
stand is at top.
Refer to “Mounting screws” for screw to be used.
Note
If you install the camera unit in an inverted position (on a ceiling, for example),
take adequate waterproofing measures to prevent water seepage into the
upper side of the stand.
Adjusting the Camera Direction and Coverage
1 Loosen the camera head fixing screw with the supplied wrench.
2 Adjust the camera to turn the lens in the desired direction.
3 Tighten the camera head fixing screw with the supplied wrench to fix
the camera.
4 Loosen the retaining screw with the supplied wrench to open the
control panel cover.
5 Adjust the zoom by the Zoom buttons.
The zoom indicator is displayed on the monitor.
6 Press the Easy Focus button to automatically adjust the focus.
7 Close the control panel cover and Tighten the retaining screw with the
supplied wrench.
8 Repeat steps 1 to 5 until the coverage and the focus are determined.
Notes
When you adjust the camera head angle without loosening camera head
fixing screw, an internal part may be damaged.
If the camera head is too heavy to be adjusted, loosen the camera head fixing
screw until it moves freely.
If you cannot achieve satisfactory focus with the Easy Focus button due to the
shooting environment, use the Focus buttons to focus manually. The focus
indicator is displayed on the monitor.
Connection
Connecting to the Network
Connect the LAN cable of the camera to a router or hub in the network using
the network cable (straight, not supplied).
To connect to a computer
Connect the LAN cable of the camera to the network connector of a computer
using the network cable (cross, not supplied).
Connecting the Power Source
There are three ways to supply the power source to this camera, as follows.
12 V DC
24 V AC
Power supply equipment pursuant to IEEE802.3af (PoE* system)
*PoE means Power over Ethernet.
Note
If the power is supplied from the power input cable and LAN cable at the same
time, the power from the LAN cable has priority over the other.
Connecting to 12 V DC or 24 V AC source
Connect the power input cable of the camera to a 12 V DC or 24 V AC source.
Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. Each usable
voltage ranges are as follows.
12 V DC: 10.8 V to 13.2 V
24 V AC: 21.6 V to 26.4 V
In the USA, The product shall be powered by a UL Listed Class 2 Power Supply
Only.
In Canada, The product shall be powered by a CSA certified Class 2 Power
Supply Only
Use UL cable (VW-1 style 10368) for these connections.
recommended cable
DC 12 V:
CABLE(AWG) #24 #22 #20
Max. length(m) 3 5 8
AC 24 V:
CABLE(AWG) #24 #22 #20
Max. length(m) 12 21 30
Wiring diagram for alarm output
Camera inside
Alarm Output +
Magnet relay –
24 V AC
24 V DC,
1 A or less
Alarm Output –
Outside
5 V
Circuit example
GND
Specifications
Compression
Video compression format JPEG/MPEG4/H.264
Audio compression format G.711/G.726 (40, 32, 24, 16 kbps)
Maximum frame rate SNC-CH180:
SNC-CH280:
Camera
IR LED 27 pcs
IR working distance SNC-CH180: 30 m (50 IRE)
SNC-CH280: 30 m (50 IRE)
Signal system NTSC color system/PAL color system (switchable)
Image device SNC-CH180:
Effective picture elements:
SNC-CH280:
Effective picture elements:
Synchronization Internal synchronization
Horizontal resolution 600 TV lines (analog video)
Video S/N More than 50 dB (AGC 0 dB)
Minimum illumination SNC-CH180:
Color 0.22 lx
SNC-CH280:
Color 0.40 lx
Lens
Focal length 3.1 mm to 8.9 mm
Maximum relative aperture F1.2 ~ F2.1
View angle SNC-CH180:
SNC-CH280:
Minimum object distance 300 mm
Interface
LAN port 10BASE-T/100BASE-TX, auto negotiation (RJ-45)
I/O port Sensor input : × 1, make contact, break contact
Alarm output : × 2, 24 V AC/DC, 1 A
(mechanical relay outputs electrically
Video output VIDEO OUT: BNC, 1.0 Vp-p, 75 ohms, unbalanced,
Microphone input* Minijack (monaural)
Recommended load impedance: 2.2 kΩ
Line input* Minijack (monaural)
* The microphone input and the line input are switchable with operating menu.
Line output Minijack (monaural), Maximum output level:
Others
Power supply 12 V DC ± 10%
24 V AC ± 10%, 50 Hz/60 Hz
IEEE802.3af compliant (PoE system)
Power consumption SNC-CH180: 30 W max.
SNC-CH280: 33 W max.
Operating temperature (AC 24 V and DC 12 V)
Start temperature: −20°C to +50°C
Working temperature: −30°C to +50°C
Operating temperature (IEEE802.3af (PoE SYSTEM))
Start temperature: 0°C to 50°C (32°F to 122°F)
Working temperature: −10°C to +50°C
Heater operation Supported only by 24V AC, 12V DC, (24V AC+
(IEEE802.3af (PoE SYSTEM) : supply only to
CF card operation Supported only by 24V AC, 12V DC, (24V AC+
(IEEE802.3af (PoE SYSTEM) : supply only to
Storage temperature –20°C to +60°C (–4°F to +140°F)
Operating humidity 20% to 80% (Non-condensing)
Storage humidity 20% to 95%
Dimensions (camera body)
ø93 mm ×186 mm (3 3/4 inches × 7 3/8 inches) not
Mass Approx. 1.9 kg (4 lb 3.0 oz)
Supplied accessories CD-ROM (User’s Guides, and supplied
Optional accessories
Wireless Card SNCA-CFW5*
* SNCA-CFW5 is not available in some countries and areas. For details,
contact your authorized Sony dealer.
Design and specifications are subject to change without notice.
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it
inspected periodically for safe use.
It may appear flawless, but the components may have deteriorated over
time, which may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony dealer.
H.264: 30 fps (1280 × 720)
H.264: 30 fps (1920 × 1080)
1/3 type CMOS (Exmor)
Approx. 1,390,000
1/2.8 type CMOS (Exmor)
Approx. 3,270,000
F1.2/View-DR Off/VE Off/AGC High/XDNR
Middle/ 50 IRE (IP)
Black & White 0 lx (IR On)
F1.2/View-DR Off/VE Off/AGC High/XDNR
Middle/ 50 IRE (IP)
Black & White 0 lx (IR On)
Vertical: 67.4° to 25.0° (1280 × 1024)
Horizontal: 85.4° to 31.2°
Vertical: 65.2° to 24.2° (1920 × 1440)
Horizontal: 88.5° to 32.3°
isolated from the camera)
sync negative
Plug-in-power supported (rated voltage: 2.5 V DC)
1 Vrms
(−4°F to +122°F)
(−22°F to +122°F)
(14°F to 122°F)
PoE) or (12V DC+PoE)
Camera operation)
PoE) or (12V DC+PoE)
Camera operation)
including the projecting parts
programs) (1), Template (1), Wire rope (1),
Screw M4 × 8 (1), Wrench (1), Installation
Manual (this document) (1 set)
Ceiling
LAN cable
Network cable
(straight, not
supplied)
10BASE-T/
100BASE-TX
Router or hub
Power
input
cable
Connecting to the power supply equipment pursuant to
IEEE802.3af
The power supply equipment pursuant to IEEE802.3af supplies the power
through the LAN cable. For details, refer to the Instruction Manual of the
equipment.
Connecting the I/O Cable
Connect the wires of the I/O cable as follows:
Wiring diagram for sensor input
Mechanical switch/open collector output device
3.3 V
Camera inside
10 K
Ω
GNDGND
2.2 K
10 K
Ω
10 K
Ω
Ω
Sensor input +
Sensor input −
(GND)
GND
Outside
Mechanical switch
or
Open collector
output device