Sony SLV-N700 User Manual

3-081-017-11 (2) US
Video Cassette Recorder
Operating Instructions
For customers in the USA
Many solutions to common problems and service information can be found at www.sony.com/vcrhelp or contact Sony VCR service at 1 (800) VHS­SONY.
www.sony.com/productregistration For all other Sony pr oduc t q uesti on s, pl ease ca ll Sony Customer
Information Services Company at 1-800-222-SONY (7669). For Custom ers i n Can ad a
If this product is not working properly, please call 1-877-602-2008 for
Peace of Mind Warranty Replacement service. For other product related questions please contact our Customer
Info rma ti on Se rvi ce C ent re at 1-87 7-899-7669 or write to us a t: Customer
Information Service 115 Gordon Baker Road, Toronto, Ontario, M2H 3R6
SLV-N700 SLV-N500
© 2003 Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’ s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION:
TO PREVENT ELECTRIC SHOC K, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Precautions
Safety
• Operate the unit only on 120 V AC, 60 Hz.
• If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
• This unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.
• Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.
• One blade of the plug is wider t han the other for the purpose of safety and will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, contact your Sony dealer.
Installing
• Allow adequate air circulation to prevent internal heat buildup.
• Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
• Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mech anical vibration o r shock.
• Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.
• Keep the unit and cassettes away fro m equipment with strong magnets, such as microwave o v ens or large loudspeakers.
• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about three hours before operating the unit.
Information
For customers in the USA
CAUTION
Y ou ar e cautioned that any changes or mo difications not expressly approved in this manual could voi d your authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However , there is no guarantee tha t interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna .
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Owner’s record
The model and serial numbers are located at the rear of the unit. Record these numbers in the spaces provided below. Refer to them whenever you call up on your Sony dealer regarding this product. Model No._______________ __________ Serial No._________________________
2
WARNING
Important Safeguards
For your protection, please read these safety instructions completely before operating the appliance, and keep this manual fo r futu re refer ence. Carefully observe all warnings, precautions and instructions on the appliance, or the one described in the operating instructions and adhere to them.
Use
Power sources
This set should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of electrical power supplied to your home, consult your dealer or local power comp any. For those sets designed to operate from battery power, or other sources, refer to the operating instructions.
Grounding or Polarization
This set is equipped with a polarized ac power cord plug (a plug having one bla de wider than t he other), or with a three-wire grounding type plug (a plug having a third pin for grounding). Follow the instructions below:
For the set with a polarized ac power cord plug:
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the polarized plug by forcing it in.
For the set with a three-wire grounding type ac plug:
This plug will only fit into a grounding-type power outlet. This is a safety feature. If you ar e unable to insert the plug into the outlet, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of th e grounding plug.
Overloading
Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity , since this can result in fire or electric shock.
Object and Liquid Entry
Never pu sh ob ject s of a ny kind i nto the set through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the set.
Attachments
Do not use attachments not recommended by the manufactu rer, as they may cause hazards.
Cleaning
Unplug the set from the wall outlet before cle aning or pol ishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with wa ter for cleaning the exterior of the set.
Installation
Water and Moisture
Do not use power-line operated sets near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
Power-Cord Protection
Route the power cord so that it is not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the plugs, receptacles, and the point where the cord exits from the appliance.
Accessories
Do not place the set on an unstable cart, stand, tripod, bracket, or table. The set may fall, causing serious injury to a child or an adult, and serious damage to the set. Use only a cart stand tripod, bracket, or table recommended by the manufacturer.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven su rfaces may cause the appliance and cart combination to overturn.
Ventilation
The slots and openings in the cabine t are provi ded for necessary ventilation. T o ensure reliable operation of the set, and to protect it from overheating, these slots and openings must never be blocked or covered.
• Never cover the slots and openings with a c loth or other materials.
• Never block the slots and openings by placing the set on a bed, sofa, ru g or ot he r si mila r surface.
S3125A
Important Safeguards
3
• Never place the set in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided.
• Do not place the set near or over a radiator or heat regist er, or where it is exposed to direct sunlight.
Antennas Outdoor antenna grounding
If an outdoor antenna or cable system is installed, follow the precautions below.
An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits. WHEN INST ALLING AN O UTDOOR ANTENN A SYSTEM, EXTREME CARE SHOULD BE T AKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATA L. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code provides information with respect to proper grounding of the mast and support ing structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Antenna Grounding According to the National Electrical Code
Antenna Lead in Wire
Ground Clamp
Electric Service Equipment
NEC-NATIONAL ELECTRICAL CODE
Lightning
For added protection for th is set during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and power-line surges.
Antenna Discharge unit (NEC Section 810-20)
Grounding Conductors (NEC Section 810-21)
Ground Clamps
Power Service Grounding Electrode System (NEC Art 250 Part H)
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer servicing to qualified service personnel under the following conditions:
• When the power cord or plu g is damaged or fraye d.
• If liquid has been spilled or objects have fallen into the set.
• If the set has been exposed to rain or water.
• If the set has been subject to excessive shock by being dropped, or the cabinet has been damaged.
• If the set does not operate normally when following the operating instructions. Adjust only those controls that are specified in the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a q ualified technician to restore the set to normal operation.
• When the set exhibits a distinct change in performance - this indicates a need for service.
Servicing
Do not attempt to service the set yourself as o pening or removing covers may expose you to dangerous v oltage or othe r hazards. Refer all servicing to qualified service personnel.
Replacement parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Safety Check
Upon completion of any service or repairs to the set, ask the service technician to perform routine safety checks (as specified by the manufacturer) to determine that the set is in safe operating condition.
4
Important Safeguards
Table of contents
Getting Started
6 Step 1 : Unpacking
7 Step 2 : Setting up the remote commander 10 Step 3 : Hookups 17 Step 4 : Selecting a language 18 Step 5 : Setting the clock 23 Step 6 : Presetting channels 27 Step 7 : Setting up the VCR Plus+® system (SLV-N700 only)
Basic Operations
30 Playing a tape 33 Recording TV programs 36 Recording TV programs using the
VCR Plus+® system (SLV-N700 only)
39 Setting the timer manually 42 Locking the VCR (Child Lock)
Additional Operations
43 Playing/searching at various speeds 45 Quick Timer Recording 46 Checking/changing/canceling timer
settings
48 Recording stereo and bilingual
programs
49 Searching using various functions 51 Adjusting the picture (tracking) 52 Changing me nu options 54 Editing with another VCR
Additional Information
56 Antenna information 57 Troubleshooting 59 Specifications 60 Index to parts and controls 65 Index
Back Cover
Quick reference to using the VCR
Getting Started
* VCR Plus+ and PlusCode are register ed trademarks of Gem s tar Development Corporation.
The VCR Plus+ system is manufactured under license from G em star Development Corporation.
Caution
Television programs, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmission and/or program owner.
Table of contents
5

Getting Started

Step 1 : Unpacking
Check that you have received the following items with the VCR:
• Remote commander
• Size AA (R6) batteries
• 75-ohm coaxial cable with F-type connectors
Check your model name
The instructions in this manu al are for the 2 models: SLV-N700 and SLV-N500. Check your model name by looking at the rear panel of y our VCR. SLV-N700 is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-N700 only.”
6
Unpacking
Step 2 : Setting up the remote commander
Inserting the batteries
Insert two size AA (R6) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.
Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.
Using the remote commander
You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV.
If the TV does not have the symbol near the remote sensor , this remote commander will not operate the TV.
Getting Started
Remote sensor
TV / VIDEO
123 456
To operate Set •TV / VIDEO to
the VCR VIDEO a Sony TV •TV
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from batter y le akage.
• Do not use a new battery with an o ld on e.
• Do not use different types of batteries.
and point at the remote sensor at the V CR
and point at the remote sensor at the T V
continued
Setting up the remote commander
7
Controlling other TVs with the remote commander
The remote commander is preprogramed to control non-Sony TVs. If your TV is listed in the following table, set the ap propriate manufacturer’s code number.
Set •TV / VIDEO at the top of the remote commander to •TV.
1
Hold down ?/1, and enter your TV’s code number using the number buttons.
2
Then release ?/1.
Now you can use the ?/1, VOL +/–, CH +/–, and TV/VIDEO buttons to control your TV. Yo u can also use the buttons marked with a dot (•) to control a Sony TV. To control the VCR, reset •TV
Code numbers of controllable TVs
If more than one code number is listed, try entering th em on e at a time until you find the one that works with your TV.
/ VIDEO to VIDEO.
TV brand Code number
Sony 01 Akai 04 AOC 04 Centurion 12 Coronado 03 Curtis-Mathes 12 Daytron 12 Emerson 03, 04, 14 Fisher 11 General Electric 06, 10 Gold Star 03, 04, 17 Hitachi 02, 03 J.C.Penn ey 04, 12 JVC 09 KMC 03 Magnavox 03, 08, 12 Marantz 04, 13 MGA/Mitsubishi 04, 12, 13, 17 NEC 04, 12
TV brand Code number
Panasonic 06, 19 Philco 03, 04 Philips 08 Pioneer 16 Portland 03 Quasar 06, 18 Radio Shack 05, 14 RCA 04, 10 Sampo 12 Sanyo 11 Scott 12 Sears 07, 10, 11 Sharp 03, 05, 18 Sylvania 08, 12 Teknika 03, 08, 14 Toshiba 07 Wards 03, 04, 12 Yorx 12 Zenith 15
8
Setting up the remote commander
Notes
• If you enter a new code number, the code nu m ber previously entered will be erased.
• If the TV uses a different remo te control system from the one programed to work with the VCR, you cannot contro l your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries.
• When you press the AUDIO MONITOR button, your TV’s menu may appear on the TV screen. To exit the TV menu, press the MENU button on the TV remote commander or wait until the me n u disappears automatically.
Getting Started
Setting up the remote commander
9
Step 3 :Hookups
Selecting the best hookup option
There are many ways in which your VCR can be hooked up. To hook up your VCR so that it works best for you, first scan through the table below. Then use the accompanying diagrams and procedures on the foll owing pages to set up your VCR.
If your TV has audio/ video inputs, ref e r to page 11 for audio/ video (A/V) hookup. Then follow one of the hookups below. If your TV does not have A/V inputs, perform directly one of the hookups below.
If you have Use Refer to
Antenna only, no cable TV Hookup 1
No cable box or cable box with only a few scrambled channels
Cable box with many scrambled channels
After you have completed the connections, follow the instructions for setup. After you have completed the set up, you are ready to use your VCR. Procedures
differ depending on the hookup you used. For an overview, refer to “Quick reference to using the VCR” on the back cover.
Before you get started
• Turn of f the power to all equipment.
• Do not co nn ect the AC power cords un til all of the conn ect ion s are compl et ed. If
you connect the A C p ow er cor d befor e the co nnec tions ar e comp leted, you may n ot be able to use the Plug and Play function.
• Be sure you make connections firmly. Loose connections may cause pi cture
distortion.
• If your TV does not match any of the examples provided, see your nearest Sony
dealer or qualified technician.
(Plug and Play) Hookup 2
(Plug and Play) Hookup 3 Page 16
Pages 12 and 13
Pages 14 and 15
10
Caution
Connectio ns between th e V C R’s VHF/UHF connector and the antenna termin als of the TV receiver should be made only as shown in the following instructions. Failure to do so may result in operation that violates the regulations of the Federal Communications Commission regarding the use and operation of RF devices. Never connect the output of the VCR to an antenna or make simultaneous (para ll el ) antenna and VCR connec tions at the antenna terminals of your receiver.
Note to CATV system installer (in USA)
This reminder is p rovided to call the CATV sys tem installer’s attention to Article 820- 40 o f the NEC that provides guidelines for prope r grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
Hookups
Audio/video (A/V) hookup
If your TV has au dio /video (A/V) inpu t ja c ks, you will get a better picture a n d s o un d if you hook up your VC R using these connections. For a true “home theater” experience, you should connect the audio outputs of your VCR or TV to your ster eo system. If your TV does not have A/V inputs, see the following pages for antenna or cable hookups.
If you are not planning to use your VCR to record programs, you finished setting up the VCR after you have made the connections shown on this page. If you want to record regular or cable TV programs, complete these connections first, and then go to the following pages for antenn a or cable hookups.
A Use this hookup if your TV has stereo jacks
LINE
LINE
IN 1
OUT
AUDIO VIDEO
Getting Started
Stereo receiverVCR
TV
IN
VIDEO AUDIO
AUDIO OUT
AUX IN
Audio/video cable (not supplied )
Audio cable (not supplied)
B Use this hookup if your TV does not have stereo jacks
Stereo receiverVCR
LINE
LINE
IN 1
OUT
AUDIO VIDEO
Video cable (not supplied)
Notes
• To play a tape in stereo, you must use the A/V connection.
• If you do not have a stereo receiver, connect the white LIN E O U T/AUDIO L jack to the AUDIO IN jack on your TV.
TV
IN
VIDEO AUDIO
Audio cable (not supplied)
AUX IN
Hookups
11
Hookup 1 (Plug and Play)
s
Antenna hookup
Make the following connections if you are using an antenna (if you do not have cable TV).
A Use this hookup if you are using:
• VHF/UHF antenna (you get channels 2–13 and channels 14 and hi gher)
• UHF-only antenna (you get channels 14 and higher)
• Separate VHF and UHF antennas
VCR
IN
OUT
B Use this hookup if you are using a VHF-only antenna (you get
channels 2–13 only)
or
or
Rear of TV
VHF/UHF
A
VHF
B
UHF
VHF
C
UHF
Match the type of connector on your TV: A, B, or C.
12
Hookups
Rear of TV
VHF/UHF
Match the type of
A
connector on your TV: A, B, or C.
VHF
For connector type
B
B and C, no UHF
UHF
connection is required.
VHF
C
UHF
VCR
or
IN
OUT
or
If you cannot connect your antenna cable to the VCR directly
If your antenna cable is a flat cable (300-ohm twin lead cable), attac h an external antenna connector (not supplied) so you can connect the cable to the RF IN connector. If you have separate cables for VHF and UHF antennas, you should use a U/V band mixer (not supplied) (page 56).
Hookup 1 : VCR setup
Plug the VCR into the AC outlet.
The VCR automatically presets the VCR’s clock and TV channels when the VCR is plugged into the AC outlet.
AC power cord
to AC outlet
The VCR starts presetting the clock and channels.
When Auto preset is completed, the current time appears in the display window.
You have now completed VCR setup. To change the on-screen display language to French or Spanish, see
“Step 4 : Selecting a language” on page 17. The clock is set using a time signal provided by some TV channels. If the clock
is incorrect, or “--:--” appears in the display win dow, see “Using Manual Clock Set” on page21.
T o add or disa b le channe ls manuall y, see “Pre se tting/disabling channels manually” on page 25.
Getting Started
Notes
• If you con nect the A C po wer co rd be fore the an tenna conne ctio ns are c ompl eted, the c hanne ls may be incorrectly set. If this happens, see “Step 6 : Presetting channels” on page 23.
• Do not press any buttons on the VCR or remote c om m ander during Auto preset.
• Auto preset starts automatically only when you plug in the AC power cord for the first time after you purchase the V CR.
• Auto preset can be performed by pressing x STOP on the VCR or more with the VCR power turned off.
continuously for 5 seconds
Hookups
13
Hookup 2 (Plug and Play)
You have no cable box, or a cable box with only a few scrambled channels
Recommended use
Use this hookup if you do not have a cable box. Also use this hookup if your cable system scrambles only a few channels.
What you can do with this hookup
• Record any unscrambled channel by selecting the channel on the VCR
What you cannot do
• Record scrambled channels that require a cable box
Wall
Connect this cable directly to your TV if you do not have a cable box.
Cable box
IN OUT
VCR
OUT
or
or
Rear of TV
VHF/UHF
A
VHF
B
UHF VHF
C
UHF
Match the type of connector on your TV: A, B, or C.
For connector types B and C, no UHF connection is required.
IN
14
Hookups
Hookup 2 : VCR setup
Plug the VCR into the AC outlet.
The VCR automatically presets the VCR’s clock and TV channels when the VCR is plugged into the AC outlet.
AC power cord
to AC outlet
The VCR starts presetting the clock and channels.
When Auto preset is completed, the current time appears in the display window.
You have now completed VCR setup. To change the on-screen display language to French or Spanish, see
“Step 4 : Selecting a language” on page 17. The clock is set using a time signal provided by some TV channels. If the clock
is incorrect, or “--:--” appears in the display win dow, see “Using Manual Clock Set” on page21.
T o add or disa b le channe ls manuall y, see “Pre se tting/disabling channels manually” on page 25.
Getting Started
Notes
• If you con nect the A C po wer co rd be fore the an tenna conne ctio ns are c ompl eted, the c hanne ls may be incorrectly set. If this happens, see “Step 6 : Presetting channels” on page 23.
• Do not press any buttons on the VCR or remote c om m ander during Auto preset.
• Auto preset starts automatically only when you plug in the AC power cord for the first time after you purchase the V CR.
• Auto preset can be performed by pressing x STOP on the VCR or more with the VCR power turned off.
continuously for 5 seconds
Hookups
15
Hookup 3
Connecting a cable box with many scrambled channels
Recommended use
Use this hookup if your cable system scrambles all or most channels.
What you can do with this hookup
• Record any channel by selecting the channel on th e cable box
What you cannot do
• Record with the cable box turned off
• Record one channel while watching another channel
Wall
VCR
IN
OUT
Cable box
IN OUT
or
or
Rear of TV
VHF/UHF
A
VHF
B UHF VHF
C UHF
After you have completed hookup…
After you have completed hookup, plug the VCR into the AC outlet and see “Step 4 : Selecting a language” on page 17.
AC power cord
Match the type of connector on y our TV: A, B, or C.
For connector types B and C, no UHF connection is required.
16
to AC outlet
Hookups
Step 4 : Selecting a language
You can change the on-screen display language.
Before you start…
• Turn on the VCR and the TV.
• Set the “VCR Output CH” to “3CH” or “4CH” in ADVANCED OPTIONS menu (page 52). If both are use d, set th e “VCR Output CH” to either channel. If your TV is connected to the VCR using A/V connections, set the TV to video input.
• Press TV/VIDEO to display the VCR indicator in the VCR’s display window.
1
2
MENU
PLAY
OK
Press MENU.
Press M/m to move the cursor (B) to “Language/Idioma/Langue.”
MENU
M/m/,
MAIN MENU
Timer set / check Clock set Tuner preset Advanced options Language / Idioma / Langue
Select
:
Vv
:Set
OK
MAIN MENU
Timer set / check Clock set Tuner preset Advanced options Language / Idioma / Langue
Select
:
Vv
:Set
b
Getting Started
: MENUQuit
: MENUQuit
3
4
PLAY
OK
MENU
Press , to select the desired language, French or Spanish.
Press MENU to exit the menu.
Selecting a language
17

Step 5 : Setting the clock

Using the Auto Clock Set feature
Some TV and cable channels transmit time signals with their broadcasts. Your VCR can pick up this time signal to automatically set the clock.
The Auto Clock Set feature works only if a channel in your area is broadc asting a time signal. If broadcasters in your area are not yet sending time signals, set the time manually (page 21).
Before you start…
• T urn on the VCR and the TV. When using
a cable box, turn it on.
• Set the “VCR Output CH” to “3CH” or
“4CH” in ADVANCED OPTIONS menu (page 52). If both are use d, s et the “VCR Output CH” to either channel. If your TV is connected to the VCR using A/V connections, set the TV to video input.
• Press TV/VIDEO to display the VCR
indicator in the VCR’s display window.
MENU
M/m/</, OK
1
2
18
Setting the clock
MENU
PLAY
OK
Press MENU.
Press M/m to move the cursor (B) to “Clock set,” then press OK.
MAIN MENU
Timer set / check Clock set Tuner preset Advanced options Language / Idioma / Langue
Select
:
Vv
:Set
OK
CLOCK SET
AUTO MANUAL
Select
:
Vv
:Set
OK
: MENUQuit
: MENUQuit
3
PLAY
OK
Press M/m to select AUTO, then press OK.
CLOCK SET
Clock set CH: Time zone: Daylight Saving:
]
AUTO
[[]
AUTO
[]
AUTO
4
PLAY
OK
Press M/m to select the item you want. Then press
</, to make the setting and press OK.
• For “Clock set CH” Leave the setting to AUTO to have the VCR automatically search for a channel that carries a time signal. Press
</, to select a
channel that carries a time signal. Use this option if you know of a channel that carries a time signal. Most PBS member stations broadcast a time signal. For the fastest response, select your local PBS station.
• For “Time zone” Select the time zone of your area, or select AUTO to have the VCR automatically set your time zone. The options are: AUTO y Atl. (Atlantic) y East (Eastern) y Cen. (Central) y Mtn. (Mountain) y Pac. (Pacific) y Alas (Alaska) y Haw. (Hawaii) y AUTO
• For “Daylight Sa v ing” Select YES or N O (stan dard t ime), or AUT O to have the VCR automatically set the daylight saving time .
Select
Clock set CH: Time zone: Daylight Saving:
Select::
Clock set CH: Time zone: Daylight Saving:
Select
Clock set CH: Time zone: Daylight Saving:
:
Vv Set : Bb
:End
OK
CLOCK SET
[] []
Vv Set : Bb OK
CLOCK SET
[[] []
:
Vv Set : Bb
:End
OK
CLOCK SET
[] []
: MENUQuit
[]
123 AUTO AUTO
: MENUQuitEnd
]
AUTO Pac. AUTO
: MENUQuit
AUTO AUTO
[]
NO
Getting Started
5
6
MENU
Select::
Press MENU to exit the menu.
To activate the Auto Clock Set function, turn off the VCR.
Vv Set : Bb OK
: MENUQuitEnd
continued
Setting the clock
19
Notes
• The clock cannot be set auto ma t ic al ly if you do not receive a channel that carri es a ti me signal in your area. If so, set the clock manually (page 21).
• If there are only a few channels in your are a th at carry time signals, setting th e c loc k automatically may take up to about 20 minutes. If nothing happens even after you wait about 20 minutes, set the clock manually (page 21).
• If you made Hookup 3, make sure you leave the cab le box on.
20
Setting the clock
Using Manual Clock Set
Before you start…
• Turn on the VCR and the TV.
• Set the “VCR Output CH” to “3CH” or “4CH” in ADVANCED OPTIONS menu (page 52). If both are use d, set th e “VCR Output CH” to either channel. If your TV is connected to the VCR using A/V connections, set the TV to video input.
• Press TV/VIDEO to display the VCR indicator in the VCR’s display window.
Getting Started
MENU
M/m/, OK
1
2
3
MENU
PLAY
OK
PLAY
OK
Press MENU.
Press M/m to move the cursor (B) to “Clock set,” then press OK.
Press M/m to select MANUAL, then press OK.
MAIN MENU
Timer set / check Clock set Tuner preset Advanced options Language / Idioma / Langue
Select
:
Vv
:Set
OK
CLOCK SET
AUTO MANUAL
Select
:
Vv
:Set
OK
CLOCK SET
YEAR
DATE
/
10120 0003 WED :
Select
:
Bb Set : Vv
:End
OK
continued
Setting the clock
TIME 12
: MENUQuit
: MENUQuit
A
M
: MENUQuit
21
Loading...
+ 47 hidden pages