SONY SLV-M10HF SERVICE MANUAL

SLV-M10HF

RMT-V249

SERVICE MANUAL

G
j

• Refer to the SERVICE MANUAL of VHS MECHANICAL
ADJUSTMENT
(9-921-647-11)

for MECHANICAL ADJUSTMENTS.

SPECIFICATIONS

US Model

Canadian Model

S MECHANISM

MICROFILM

VIDEO CASSETTE RECORDER

[ NOTE ON REP AIRING HARNESSES BETWEEN AN-16/17

BOARDS AND NL-2 BOARD ]

AN-16 board NL-2 board
CN201 CN002
AN-17 board NL-2 board
CN101 CN001

Be sure to use the original one or equivalent (AWG, length).
If not so, the resonance frequency will be changed.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.

2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair . Point
them out to the customer and recommend their replacement.

4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.

5. Check the line cord for cracks and abrasion.
Recommend the replacement of any such line cord to the
customer.

6. Check the B+ voltage to see it is at the values specified.

7. Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.

T o Exposed Metal

Parts on Set

AC

0.15

µ

F

1.5 k

Ω

Voltmeter
(0.75 V)

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA
TW-540A. Follo w the manufacturers' instructions to use these
instruments.

2. A battery-operated A C milliammeter. The Data Precision 245
digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC v oltmeter. The "limit" indication
is 0.75V, so analog meters must have an accurate lo w v oltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V A C range are suitable. (See
Fig. A)

Earth Ground

Fig. A. Using an A C v oltmeter to check A C leakage.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS P AR SONY.

— 2 —

TABLE OF CONTENTS

SERVICE NOTE

1. ERROR CODE INDICATION··········································· 5

1. GENERAL

Getting Started

Unpacking··············································································1-1
Setting up the remote commander ·········································1-1
Hookups ·················································································1-2
Selecting a language ······························································1-8
Setting the clock ····································································1-8
Setting up cable box control ··················································1-9
Presetting channels ······························································1-11
Setting up VCR Plus+··························································1-12

Basic Operations

Playing a tape·······································································1-13
Recording TV programs ······················································1-13
Locating a channel by station ID ·········································1-14
Recording TV programs using VCR Plus+ ·························1-15
Setting the timer manually···················································1-16

Additional Operations

Playing/searching at various speeds ····································1-16
Searching for a selected point on the tape ···························1-17
Skip-searching automatically···············································1-18
Creating a favorite channel list with station IDs··················1-18
Recording TV programs using the quick timer ···················1-18
Checking/changing/cancelling timer settings ······················ 1-19
Recording stereo and bilingual programs ····························1-19
Searching using the index function······································1-20
Adjusting the picture ··························································· 1-20
Changing menu options ·······················································1-20
Editing with another VCR ···················································1-21

SmartFile function

About the SmartFile function ··············································1-21
Recording using the SmartFile function ······························ 1-22
Selecting and playing a program ·········································1-23
Checking the contents of a tape ··········································· 1-23
Labelling a recorded program and tape ·······························1-23
Protecting a recorded program·············································1-25
Erasing the data of an unwanted program ···························1-25
Storing program data from the DSS receiver
(Program Data Download)···················································1-25

Additional Information

General setup information ···················································1-26
Index to parts and controls···················································1-26

2. DISASSEMBLY

2-1. UPPER CASE,

FRONT PANEL BLOCK ASSEMBLY ··························2-1
2-2. FR-139, DM-81, AJ-2, AN-17 BOARDS ·······················2-1
2-3. NL-2 BOARD, REAR PANEL ·······································2-1
2-4. POWER BLOCK, MA-335 BOARD

(WITH S MECHANISM DECK) ···································2-2
2-5. AN-16 BOARD, S MECHANISM DECK ·····················2-2
2-6. INTERNAL VIEWS························································2-3
2-7. CIRCUIT BOARDS LOCATION ···································2-4

3. BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM ····································3-1
3-2. VIDEO BLOCK DIAGRAM ··········································3-3
3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM ·····3-5
3-4. AUDIO BLOCK DIAGRAM ·········································· 3-7
3-5. MODE CONTROL BLOCK DIAGRAM·······················3-9
3-6. TUNER BLOCK DIAGRAM ·······································3-11
3-7. POWER SUPPLY BLOCK DIAGRAM ·······················3-13

4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM································4-1
4-2. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS ············································ 4-3

• MA-335 (REC/PB AMP, VIDEO, SERVO/SYSTEM
CONTROL, AUDIO, TUNER)
PRINTED WIRING BOARD ·························4-3

• MA-335 (REC/PB AMP) SCHEMATIC DIAGRAM ··4-5

• MA-335 (VIDEO, NORMAL AUDIO)
SCHEMATIC DIAGRAM ······························4-8

• MA-335 (SERVO/SYSTEM CONTROL)
SCHEMATIC DIAGRAM ····························4-11

• MA-335 (ON SCREEN DISPLAY)
SCHEMATIC DIAGRAM ····························4-15

• MA-335 (DSF) SCHEMATIC DIAGRAM················4-17

• MA-335 (V-SET) SCHEMATIC DIAGRAM ············4-19

• MA-335 (AFM AUDIO)
SCHEMATIC DIAGRAM ····························4-21

• MA-335 (TUNER) SCHEMATIC DIAGRAM··········4-23

• MA-335 (POWER SUPPLY, AV-BUS)
SCHEMATIC DIAGRAM ····························4-25

• FR-139 (MODE CONTROL)
PRINTED WIRING BOARD ·······················4-27

• FR-139 (MODE CONTROL)
SCHEMATIC DIAGRAM ····························4-29

• DM-81 (OPERATION SWITCHES)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ····························4-31

• AJ-2 (LINE-2 IN)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ····························4-32

• AN-16 (INNER SMARTFILE SENSOR/WRITER),
AN-17 (FRONT SMARTFILE SENSOR)
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS··························4-33

• NL-2 (SMARTFILE)
PRINTED WIRING BOARD ·······················4-35

• NL-2 (SMARTFILE)
SCHEMATIC DIAGRAM ····························4-37

• POWER BLOCK SR821 (SWITCHING REGULATOR)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ····························4-39

5. INTERFACE, IC PIN FUNCTION
DESCRIPTION

5-1. SYSTEM CONTROL —

VIDEO BLOCK INTERFACE
(MA-335 BOARD IC161)···············································5-1

5-2. SYSTEM CONTROL —

SERVO PERIPHERAL CIRCUIT INTERFACE
(MA-335 BOARD IC161)···············································5-1

5-3. SYSTEM CONTROL —

MECHANISM INTERFACE
(MA-335 BOARD IC161)···············································5-2

5-4. SYSTEM CONTROL —

SYSTEM CONTROL PERIPHERAL
CIRCUIT INTERFACE (MA-335 BOARD IC161) ·······5-2

5-5. SYSTEM CONTROL —

AUDIO BLOCK INTERFACE
(MA-335 BOARD IC161)···············································5-2

5-6. SERVO/SYSTEM CONTROL MICROPROCESSOR

PIN FUNCTIONS (MA-335 BOARD IC161)················5-3

5-7. TUNER/TIMER MODE CONTROL PIN FUNCTIONS

(FR-139 BOARD IC460) ················································5-4

— 3 —

6. ADJUSTMENTS

6-1 MECHANICAL ADJUSTMENTS ·································6-1
6-2. ELECTRICAL ADJUSTMENTS ···································6-1
2-1. PREPARATION BEFORE ADJUSTMENT···················6-1
2-1-1.Equipment Required ························································6-1
2-1-2.Equipment Connection ····················································6-1
2-1-3.Input Signal Check ··························································6-1
2-1-4.Alignment Tape ·······························································6-1
2-1-5.Input/Output Levels and Impedance ·······························6-2
2-1-6.Adjustment Sequence ······················································6-2
2-2. POWER SUPPLY CHECK ·············································6-2
2-2-1.Output Voltage Check (MA-335 Board) ·························6-2
2-3. SERVO SYSTEM CHECK ·············································6-3
2-3-1.RF Switching Position/

AF Switching Position Adjustments (MA-335 Board) ···6-3
2-4. VIDEO SYSTEM CHECKS ··········································· 6-4
2-4-1.X’tal OSC Check (MA-335 Board)································· 6-4
2-4-2.SYNC AGC Check (MA-335 Board)······························6-4
2-4-3.Recording Y Level Check (MA-335 Board) ···················6-4
2-4-4.Recording Chroma Level Check (MA-335 Board) ·········6-5
2-4-5.Playback Level Check (MA-335 Board) ·························6-5
2-5. AUDIO SYSTEM ADJUSTMENT·································6-5
2-5-1.ACE Head Adjustment ····················································6-5
2-5-2.E-E Output Level Check ·················································6-5
2-5-3.Overall Output Level and Distortion Factor Check·········6-6
2-5-4.Overall Noise Level Check··············································6-6
2-6. TUNER SYSTEM ADJUSTMENT································ 6-6
2-6-1.Separation Adjustment (MA-335 Board) ························6-6
2-7. ADJUSTING PARTS LOCATION DIAGRAM ·············6-8

7. REPAIR PARTS LIST

7-1. EXPLODED VIEWS ······················································7-1
7-1-1.FRONT PANEL ASSEMBLY AND UPPER CASE

SECTION ········································································7-1
7-1-2.CHASSIS SECTION·······················································7-2
7-1-3.MECHANISM DECK-1 ·················································7-3
7-1-4.MECHANISM DECK-2 ·················································7-4
7-1-5.MECHANISM DECK-3 ·················································7-5
7-2. ELECTRICAL PARTS LIST ··········································7-6

— 4 —

SERVICE NOTE

1. ERROR CODE INDICATION

• Error codes are indicated using the lower 5 digits in the fluorescent display tube.
“At this time, Colon “:” between character is not indicated.”

Mode code indication when the error has occurred.

Error code

ERROR CODE

0 No error
1 Cam encoder error Loading direction
2 Cam encoder error Unloading direction
3 T reel error
4 S reel error
5 Capstan error
6 Drum error
7 Error on initializing
8 Cassette loading error
9 Reserve

SLV-M10HF

MODE CODE

0 Power-on eject 10 FWD x1 20 REW play
1 Power-on initial 11 FWD x2 21 Cas. loading
2 Power-off eject 12 CUE 22 Tape loading
3 Power-off stop 13 PB-pause 23 Power-off loading
4 FF 14 RVS-pause 24 Mecha. error (Power on)
5 REW 15 RVS x1 25 Power-on eject initial
6 REC 16 RVS x2 26 Power-off eject initial
7 REC- pause 17 REV 27 APC REC
8 Power-on stop 18 Power-off initial 28 Cas. loading
9 PB 19 Mecha. error (Power off) (No auto PB check)

— 5 —

SECTION 2

)

Front panel assembly

1

Screws (B2.6 × 8)

2

DM-81 board

2

FR-139 board

3

Flat cable
From CN140 on
FR-139 board

3

Frexible board
From CN441 on
DM-81 board

1

Screws (B2.6 × 8)

6

Screw (B2.6 × 8)

4

Screw (B2.6 × 8)

8

AJ-2 board

7

JK ground plate

9

AN-17 board

5

Antenna (large) shield plate <Note>

Note : When peeling off the antenna (large) shield plate,
be sure to apply it to the original position on the
AJ-2 board.
If not so, the resonance level of AN-17 board
becomes small.

DISASSEMBLY

NOTE: Follow the disassembly procedure in the numerical order given.

2-1. UPPER CASE, FRONT PANEL BLOCK ASSEMBLY

3

Connector
From CN423 on
MA-335 board

4

3

Flat cable
From CN162 on
MA-335 board

Hooks

1

Screws (case)

2

Upper case

SLV-M10HF

1

Screws (case

5

Front panel

block assembly

4

Hooks

2-2. FR-139, DM-81, AJ-2, AN-17 BOARDS

2-3. NL-2 BOARD, REAR PANEL

1

Screws

4

Hooks

4

Hooks

2

NL-2 board

4

Hooks

4

Hooks

5

Rear panel

4

Hooks

3

2-1

Release cable stopper

from rear panel

2-4. POWER BLOCK, MA-335 BOARD (WITH S MECHANISM DECK)

1

Remove two screws securing NL holder and remove
NL holder.

2

Connector

(From CN201 on power block)

5

Screws

MA-335 board

6

(with S mechanism deck)

a

a

2

3

Screws

4

Power block

2-5. AN-16 BOARD, S MECHANISM DECK

1

Flexible board
From CN260 on
MA-335 board

4

Screws

7

AN-16 board

6

AN holder

MD base (R)

5

2

Screws

MD base (M)

S mechanism deck

MA-335 board

MD base (R)

2-2

2-6. INTERNAL VIEWS

y

y

— T op View —

M901
Drum Assembly DZH-94A/Z-RP
8-839-044-02

ACE head block assembly
A-6759-620-A

FE head
1-500-144-11

— Bottom View —

Reel (S) table
3-977-507-01

Pinch press block assembl
A-6759-615-A

FL complete assembly
A-6759-619-C

Reel (T) table
3-977-508-01

M902
DC motor (capstan)
1-698-971-11

M903
Cam motor assembly
X-3947-577-1

M901
Drum Assembl
DZH-94A/Z-RP
8-839-044-02

Rubber belt
3-977-510-01

2-3

2-7. CIRCUIT BOARDS LOCATION

MA-335
REC/PB AMP, VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER

AJ-2
(LINE-2 IN)

AN-17
FRONT
SMARTFILE
SENSOR

FR-139
(MODE CONTROL)

NL-2
(SMARTFILE)

AN-16
INNER SMARTFILE
SENSOR/WRITER

POWER BLOCK SR821

DM-81
(OPERATION SWITCHES)

2-4E

3-1. OVERALL BLOCK DIAGRAM

SECTION 3

SLV-M10HF

BLOCK DIAGRAMS

CJ570
LINE 1

IN

CJ801
LINE 2

IN

NORMAL

AUDIO

CJ801
LINE 2

IN

CJ570
LINE 1

IN

CH 1

CH 2

CH 1

CH 2

CH 1

CH 2

REC/

ERASE

HEAD

HEAD

(SEE PAGE 4-32)

AJ-2

BOARD

VIDEO

VIDEO

VIDEO
HEAD

SP

SP

EP

EP

AUDIO
HEAD

L VIDEO 2

L VIDEO 1

IC260

VIDEO

REC/PB

QAMP

IC340

AFM

REC/PB

QAMP

L 1(L)

L

AUDIO

L 1(R)

R

MA-335 BOARD

PB Y/C

REC Y/C

C ROT

C SYNC

S OUT 1

S CLK 1

RF SWP

RF ENV

FM PB

FM REC

AF REC

AF SWP

REC P

IC201

(1/2)

Y/C

PROCESSOR

(SEE PAGE 4-32)

AJ-2

BOARD

L 2(L)

L

AUDIO

PB

L 2(R)

R

A HEAD PB

IC403

A HEAD REC

VIDEO

AMP

T331,Q330

BIAS

ERASE

OSC

(SEE PAGE 4-5,8,11,15,17,19,21,23,25)

VIDEO

IC501

HD

VD

AFC

H DET
MEDIA VIDEO
TU VIDEO

Q VD

I2C DATA VIDEO

I2C CLOCK VIDEO

IC202

1H

DELAY

S VHS

(HIFI)

NORM OUT

(2/2)

A L
A R
RF AUDIO
TU L
TU R

I2C DATA 1

I2C CLOCK 1

AF ENV

AF SWP

IC360

AUDIO

PROCESSOR

NORM IN

IC201

AUDIO

PROCESSOR

(MONO)

IC500

OSD

IC871

SYNC

DET/SET

V SET CS

SO 0

SCK 0

SO 0

SCK 0

SCK 0

IN

IN

Q560

RF VIDEO

SI 0

VIDEO

CJ570

AUDIO

LINE
OUT

L

R

VHF/
UHF

4CH

3CH
S701

RF CH

OUT

RF

TU700

TUNER/MOD/IF

RF VIDEO

TU VIDEO

RF AUDIO

MPX

AFT

TV/VTR
PLL DATA
PLL CLOCK
PLL ENB

AFT

Q VD

S VHS
C SYNC

S OUT 1
S CLK 1
RF SWP
RF ENV

SYSTEM

CONTROL

IC160

DRUM

SERVO

CAPSTAN

SERVO

D VS

D PG

D FG

CAP VS

CAP FG

CTL REC/PB

IC100

IC100

IC140 IC141

AMP

CTL

DRUM MOTOR

DRUM

M

MOTOR

DRUM

PG

DRUM

FG

CAPSTAN MOTOR

CAPSTAN

M

MOTOR

CAPSTAN

FG

CTL

AMP

IC101

IC733

ST/BILNG

PROCESSOR

MPX

F MONO,MAIN/SAP

SAP,STEREO

SIGNAL

CONTROL

I2C DATA 1
I2C CLOCK 1

AF ENV

AF SWP

AF REC
AF SWP

REC P

REC P

CAM +,-

MODE1-4

T REEL FG

S REEL FG

T SENS

S SENS

T/S LED

NICOLON
CDC POWER

PH102
T REEL

PH101
S REEL

T SENS

S SENS

Q103

LED

DRIVE

Q101

Q102

IC980

SIRCS

SIRCS

CBC I/O

LOADING

MOTOR

SW12V

D103

(T/S LED)

CNJ981

IN

CNJ980

OUT

ROTARY
SWITCH

CABLE BOX

CONTROL/

CONTROL S

LOADING

M

MOTOR

(SEE PAGE 4-33)

AN-16

BOARD

(SEE PAGE 4-34)

AN-17

BOARD

CNJ001

CPD

SMARTFILE

SENSOR

BLOCK

IC001

IC002

MANCHESTER

CODE

MOD./DEMOD.

/SERIAL

TRANSFER

CONTROL

IC003

IN

IC004

EEPROM

NL-2

BOARD

(SEE PAGE 4-37)

SMARTFILE

CONTROL

SO 0

SI 0

SCK 0

FULL

ERASE

HEAD

IC464

REMOTE
CONTROL
RECEIVER

IC462

EEPROM

IC460

MODE

CONTROL

SO 0

SCK 0

SI 0

SIRCS IN

SIRCS OUT

IC463

POWER

FAIL DET

RESET

PULSE GEN

SI 0
SO 0
SCK 0

VSET CS
H DET

16

ND420

FLUORESCENT

INDICATOR TUBE

-F +F

S403-410

A/D0-2

FUNCTION

KEY

S411,412

A/D3

FUNCTION

DMS1,2

KEY

FR-139 BOARD

(SEE PAGE 4-29)

PAUSE

(SEE PAGE 4-31)

DM-81

BOARD

S441-443

FUNCTION

KEY

DMS

BLOCK

3-1 3-2

SLV-M10HF

3-2. VIDEO BLOCK DIAGRAM

MA-335 BOARD

(SEE PAGE 4-32)

AJ-2

BOARD

L2 V

CN801

CN423

1

1

(SEE PAGE 3-12)

SW3SW3

SW7

SW4

SW8

SW6

SW10

SW5

SW9

REC

SW1

REC

SW2

200mV/Div 0.1µsec/div

PB

PB

PB

PB

CN260

11

10

7

6

9

8

13

12

3
2

5
6

13
14

11
10

4

12

CN261

REC CURR

1

PB RF

2

RF SWP

3



CN261 2 PB

CN261 3 PB

5Vp-p

16

30Hz

IC260 4 REC

1V/Div

0.1µsec/div

CH1

CH2

CH1

CH2

SP

SP

EP

EP

CJ801
LINE 2

IN

VIDEO

CJ570
LINE 1

IN

VIDEO

DRUM
VIDEO
HEAD

CHECK

PIN

(SEE PAGE 4-5,8,15,17,19)

FROM/TO

TUNER

TU700

BLOCK

VIDEO REC/PB AMP

COMP

REC

IDEL

VCA

30

IC260 #º REC

CN261 1 REC

36

IC201 @• REC

IC260

PB RF

REC RF

0.5V/Div

0.1µsec/div

H

HPF

LOGIC

CJ570

LINE

Q502

Q211

BUFFER

CLP

BUFFER

Q875

BUFFER

Q873,874

WAVE

SHAPER

IC871 #º REC/PB

R
P

IC871

SYNC

DET/SET

26

VIDEO

SO

SI

SCK

28

H SYNC

IRQ

29

V SYNC

RESET

31

30

X871

4.8Vp-p
8MHz

FSC
BPF

R
P

R,A

VXO1

B

SERIAL

DECODER

IC501 !º REC/PB

(2/2)

340mVp-p

10

11

2

3
8

9

VIDEO

VCO I

VCO O

V IN
EXS

XS

13

503.5kHz

0.65Vp-p

IC501

AFC

IC500

OSD

H SUNC
V SYNC

V SYNC

Q210

BUFFER

IC201 $• PB

IC201 %º PB

DET

YOUT

HD

9

VD

5

8

25

12
13

23S IN
22S CLK
18CS

11

52

26

0.23Vp-p

H

Q871,872

VIDEO

2Vp-p

Q209

BUFFER

150

3

IC201 $• REC
IC201 %º REC

0.5Vp-p

S VHS

DET

6865 69

AMP

X501

X500

14.318MHz

IC202

1H
DL

Q208

DE

EMPH.

H

SW 5V

IC500 3, @∞ REC/PB

IC201 #∞ REC

1Vp-p

35

37

15

Q801

BUFFER

Q802

H

VIDEO

AGC

SUNC

SEP

IC201 !∞ PB

C ROT66

R
P

PB Y/C

Q802,803

EQ AMP

Q851-854

CLAMP

B PB

0.2V/Div

0.1µsec/div

RF ENV IC160 60
C SYNC IC160
S OUT1 IC160
S CLK1 IC160
RF SWP IC160

200mV/Div 0.1µsec/div

C

LPF

SEQ

Q804,D801

PB RF

Q855-857

SHAPER

R
P

R
P

Q806-808

BUFFER

WAVE

Q810 E PB

66

FROM/TO

80

SYSCON

81

(SEE PAGE 3-6)

1

Y/C
MIX

Q809

BLOCK

ACC
AMP

Q805

SP
SW

SW

0.1V/Div

0.1µsec/div

R
P

(1/2)

IC201

Y/C PROCESSOR

Y/C 1

30

CLP

TU V

1Vp-p

ENV
DET

C ROT

C SYNC

CLOCK

RF SWP

DATA

Y/C 2

32

CLP

Y/C 3

28

CLP

IC201 #¶ REC/PB

H

IC260 !• REC/PB

SW5V

L263

29
16

26

L262

IC260 !¶ REC/PB

5Vp-p
30Hz

21

18
19
20
17

34

4Vp-p

2.3Vp-p

H

Q260

BUFFER

22

AGC

24

Q204

C

TRAP

27

Q201

BUFFER

28

IC260 @™ PB

200mV/Div

0.1µsec/div

IC260 @• REC

COMV.

Q810

BUFFER

R
P

MAIN

IC201 #• REC/PB

H

QH/QV

INS

SEP Y NR

R
P

KIL

14

21

20

18

S
N

REC RF

VIDEO

AMP

CLP

2Vp-p

BPF

AGC

RP

FM

REC

NT

EQ

IC500 9 REC/PB

5Vp-p

14.31818MHz

L204

36Y VCC
47C VCC

L206

38

40

42

5

43

12

DL

EQ

R
P

DEM

FM

MOD

H

SW5V

BUFFER

(1/2)

IC202

1H
DL

CLK

48

25

IC201 @∞ REC

H

DE

EMPH.

Q214

Q505

7

10

BUFFER

20mV/Div

0.1µsec/div

Q560

BUFFER

Q803

RF VIDEO TU700

P CONT1 CN162

17
16
15

32

19

SI0 CN162
SO0 CN162
SCK0 CN162

V SET CS CN162

SYS RESET CN162

HDET CN162

CG CS CN164
CG V CN164

33

Q VD IC160

5

(SEE PAGE
3-11)

21

7
8
6

18

20

2

12
23

FROM/TO

(SEE PAGE
3-6)

4

TO
TUNER
BLOCK

SYSCON

BLOCK

45

46

56

55

64

IC201 $∞ PB

H

X201

3.579MHz

IC201 %§ REC

IC201 %§ PB

I2C DATA VIDEO IC160
I2C CLOCK VIDEO IC160

S VHS IC160

3.579545MHz
550mVp-p

3.579545MHz
500mVp-p

500mVp-p

28
3063

12

OUT

VIDEO

3-3 3-4

3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM

SLV-M10HF

DRUM MOTOR

M901

OUTPUT

M902

OUTPUT

SW5V

HALL

DEVICE

M

HALL

DEVICE

CAPSTAN MOTOR

MATRIX

CAPSTAN

U+
U­V+
V­W+
W-

U

V

W

VCC

MA-335 BOARD

M12V

D VS

D PG

D FG

LIMITER

D107

CVS

CAP RVS

CAP FG

MODE1
MODE2
MODE3
MODE4

M12V

IC141

CTL AMP

13

D109

SW5VM12V

CN101

1

1

2

2

3

PG

FG

VM

VCC

TL

FG

CTL

HEAD

LOADING

MOTOR

CAM

ENCODER

MECHA

(

POSITION

3

4

4

CN102

7

7
1

1
6

6

5

5

2

2

3

3

CN301

6

5

CN103

CN103
1
2

M

3

4
3
2

(

1

(SEE PAGE 4-8, 11, 26)

IC100

CAP ERR

INTEG

7

IC161 ^• REC/PB

IC161 ^ª REC/PB

PS101

IC100

CAP ERR

INTEG

1

IC161 &º REC/ PB

IC140

CTL

REC/PB

AMP

(1/2)

REF 2.5V
5
6

5Vp-p
30Hz

5Vp-p 360Hz

(2/2)

REF 2.5V
3
2

5Vp-p

1.078kHz

72

Q140
GAIN

SW

IC161

SERVO CONTROL

74

DRUM DA

68

DRUM PG

69

DRUM FG

84

CAP TRQ PWM

99

STEP PLS

35

CAP STOP

73

CAP DA

72

CAP RVS

70

CAP FG

7

REC CTL

67

PB CTL

92

CTL HYSHIGH

8

CTL RESET

(1/2)

IC161 &¢ REC/PB

5Vp-p
360Hz

IC161 &£ REC/PB

5Vp-p
360Hz

IC161 7 REC

4Vp-p 30Hz

IC161 ^¶ REC

5Vp-p
30Hz

M12V

L101

D103

D103

T/S LED

D6V

IC101

LOADING

MOTOR DRIVE

8

VCC1

9

VCC2

2

CAM+

10

CAM-

SW12V

IN1

IN2

3

4

D6V

PH102

T REEL

PH101

S REEL

TAKE END

SENSOR

SUPPLY END

SENSOR

S101
REC

PROOF



IC161 $£ REC/PB

3Vp-p
16MHz

D161

FG

FG

Q101

Q102

Q103

LED

DRIVE

L161

X160

16MHz

MODE1
MODE2
MODE3
MODE4

53

AVREF

54

AVDD

89

VDD

90

5V

64

T REEL FG

63

S REEL FG

61

T SENS

62

S SENS

32

T/E LED

15

REC PRF

42

XTAL

43

EXTAL

9

CAM2

22
21
20
19

MODE1
MODE2
MODE3
MODE4

(2/2)

IC161

SYSTEM CONTROL

CLOCK(SSB)

ASURA RESET

SDA 0
SCL 0

AF REC

S VHS

RF ENV

V SYNC

DATA(SSB)

RF SWP

NICOLON

S CLK
S IN 0

S OUT 0

ASURA CS

F MONO

TA MUTE

TV/VTR

Q214

IC201
IC201

IC260
IC201

IC260
IC260

IC260

IC201
IC871

IC500
IC500
IC871
IC871
IC501
IC500
IC500
Q503

Q604
IC601

REG OUT

CONTROL

S OUT

CONTROL

S IN

41
42

70
39

,IC360

1
4
5

,IC201

65

64
63

26

,IC260

37
19

20
17

33
17

,IC871

23

,IC871

22
19
32

8
24
11

4

1

9

11

11
10

8

33
21

FROM/TO

20

TUNER
BLOCK

22

(SEE PAGE 3-12)

7
5

4

40

(SEE PAGE 3-8)

18

(SEE PAGE
3-3, 4)

16
15

TO

POWER

BLOCK

FROM/TO

AUDIO
BLOCK

FROM/TO

VIDEO
BLOCK

SIRCS OUT

SIRCS IN
P CONT2
P CONT1

VSET CS

SYS RESET

ASURA CS

PLL ENABLE

PLL CLOCK

PLL DATA

TU AFT

MAIN/SAP

STEREO

LANC IN

LANC OUT

CG V
CG CS
H DET

S CK 0

S O 0

S I 0

SAP

D6V

CN162

CN165

22
21
23
12

18
20

19

15
14
13
11
16
17

10

5
3

2

6
8
7

4

9

2
3
4

FOR

CHECK

CNJ980

OUT

CNJ981

IN

TO/FROM

MODE

CONTROL

BLOCK

(SEE PAGE 3-9)

CABLE BOX

CONTROL/

CONTROL S

28
30

31A MUTE
59AF ENV

100AF SWP

2AF REC P

96
12

IC161 1 REC/PB

100

IC161

5Vp-p

60
66

80
81

1

77REC CONT

4Q VD

49CBC POWER
48

40
47
45
46
44

50
11

26

30Hz

I2C DATA1 IC360
I2C CLOCK1 IC360

A MUTE IC201
AF ENV IC360
AF SWP IC340
AF REC P IC340
AF REC IC340

S VHS

I2C DATA VIDEO
I2C CLOCK VIDEO

RF ENV
C SYNC

S OUT1
S CLK1

RF SWP

Q VD

S I 0
S O 0
S CK 0
SYS RESET
VSET CS
H DET
CG CS
CG V
P CONT1

P CONT1
P CONT2

IC980

SIRCS/CBC

I/O

REG

12

ON/OFF

6

STATUS

4

S IN

5

S OUT

STEREO IC733
SAP IC733
MAIN/SAP IC733

TU AFT TU700
PLL DATA TU700
PLL CLOCK TU700
PLL ENABLE TU700

F MONO IC733
TA MUTE IC733

TV/VTR TU700

16

3-5 3-6

SLV-M10HF

3-4. AUDIO BLOCK DIAGRAM

CJ570
LINE 1

IN

CJ801
LINE 2

IN

CH1

CH2

DRUM

AUDIO

HEAD

AUDIO

AUDIO

FOR

CHECK

L

R

L

R

MA-335 BOARD

FM PB

3

HF ADJ

1

CN341

CN260

3

2

1

17

18

24

20

16

13

(SEE PAGE 4-32)

AJ-2

BOARD

CN801

L2 L

L2 R

3

5

REC ON

PB ON

3

5

(SEE PAGE 4-5, 21)

IC340

AFM

REC/PB

AMP

HA

VCC

VCC

HA

CA

AGC

AGC
DET

CN423

AGC

AMP

SW5V

14

VCC

EP

SP

L341

H SW

REC MUTE

REC

41

HF

LPF

IC360

AUDIO

PROCESSOR

(HIFI)

VCO

VCO

INPUT SEL

PNR

PNR

15
14

SEL

NORMAL IN

NORMAL OUT

MUTE

MUTE

MUTE1213

16
17

RF AUDIO TU700 1

FROM/TO

TUNER
BLOCK

3

(SEE PAGE 3-11, 12)

4

SW5V

76

AVCC

PB
PB

ALC

REC

REC

LINE
AMP

MUTE

MUTE

CTL

REC

REC:EP,LP

PB:EP

TU AUDIO L IC733
TU AUDIO R IC733

(2/2)

EQ

PB:

LP,SP

3

4

10 11

9
8

1
2

21

20

IC201

AUDIO

PROCESSOR

(MONO)

7

75
73
71

A-H SW

80

AUTO

AUTO

BIAS

6

Q301
BIAS

SW

Q387

77

7915

70

MUTE

Q386

Q379

MUTE

MUTE

SW

OUTPUT

L

L

SEL

L

R

AUDIO

CJ570

LINE
OUT

SW12V

35

SW12V

SW12V

HF

LPF

3

9

1

4
5

FM PB

FM REC

37

36

40

AF SWP

AGC
AMP

LEVEL

DET

SCL42SDA

39 5 6 3 4

NOMAL

AUDIO

AUDIO

REC/PB

HEAD

FULL
HEAD

FULL

ERASE

HEAD

HEAD

CN301

1

IC301

HEAD

2

4

1

CN302

16

SW

T331,Q331

BIAS

ERASE

OSC

42

SW5V

A MUTE IC161 31

I2C DATA1 IC161
I2C CLOCK1 IC161
AF ENV IC161

AF SWP IC161
AF REC P IC161
AF REC IC161

28

FROM/TO

30

SYSCON

59

BLOCK

(SEE PAGE 3-6)

100

2

96

3-7 3-8

3-5. MODE CONTROL BLOCK DIAGRAM

SLV-M10HF

FROM/TO

SYSCON

BLOCK

(SEE PAGE 3-6)

FR-139 BOARD

CN460

SIRCS OUT

27

SIRCS IN

29

P CONT 2

10

P CONT 1

11

CG V

9

CG CS

20

H DET

30

VSET CS

14

SYS RESET

12

S CK 0

26

S O 0

24

S I 0

25

ASURA CS

13

PLL ENABLE

17

PLL CLOCK

18

PLL DATA

19

TU AFT

21

MAIN/SAP

16

SAP

15

STEREO

28

LANC IN

23

LANC OUT

22

16

(SEE PAGE 4-29)

L182

D6V

D463

D462

5

7

2

CONTROL
RECEIVER

BZ460

IC463

RESET
PULSE

GEN.

POWER

FAIL

DET.

IC464

REMOTE

IC462

EEPROM

MODE

SDA
SCL

VL+

1

2

VS+

1

VS-

2

(SEE PAGE 4-34)

CN101

11

VL-

2

CN201

11

2

(SEE PAGE 4-33)

AN-17

BOARD

AN-16

BOARD

NL-2 BOARD

CNJ001

CPD

IN

CN464

SCK0

4

SO0

2

SI0

3

RESET

5

X CS

IC460

TIMER/TUNER

MODE CONTROL

24

AVDD

72

VDD

75

VPP

6

8

1

5
6
7

34

RST

2

POWER FAIL

6

SIRCS OUT

4

SIRCS IN

79

P CONT 2

78

P CONT 1

80

CG V

27

CG CS

3

H DET

40

VSET CS

77

SYS RESET

10

S CK 0

12

S O 0

11

S I 0

76

ASURA CS

37

PLL ENABLE

35

PLL CLOCK

36

PLL DATA

23

TU AFT

37

MAIN/SAP

35

SAP DET

36

STEREO DET

14

LANC IN

15

LANC OUT

28

SDA

26

SCL

13

WC

7

BUZZER

G1

G10

SEG1

SEG16

X CS

EXTAL

XTAL

TEX

JOG LED

A/D 4

A/D 3
DMS 2
DMS 1

A/D 2

A/D 1

A/D 0

ML LED

71
62

44
59

22

43

X460

16MHz

42

TX

55

X461

32.768kHz

54

29
20
19
42
41

74

17
16

21

S406

CURSOR

S411

REW

Q461

LED

DRIVE

Q460

LED

DRIVE

ND420

VACUUM FLUORESCENT

INDICATOR TUBE

S412

FF

S404

SMART

FILE

S405
EASY

SETUP

S409 S410
CH

D464

SMARTFILE

D460

POWER ON

S403

COMMAND

MODE

D5V

D5V

CH+

F+
F-

-30V

S407

OK

FROM
POWER
BLOCK

S408

INPUT

SELECT

1

CN461 CN440

JOG LED

55

PAUSE

4

A/D 4

3

DMS 2

1

DMS 1

2

Q015

CN004

4
2
3
5
1

DM-81 BOARD

4
3
1
2

(SEE PAGE 4-37)

IC003

SMARTFILE CONTROL

56

DSS IN

48

SCK0

49

SI0

50

SO0

30

RST

47

CS0

SDA0 SCL0

80 78

5 6

IC004

EEPROM

S444

PAUSE

S441

EJECT

MANCHESTER CODE MOD./DEMOD.

53SO1
52SI1

SCK1

51

X RST

8

ANT SEL

7

REQ

9

TOTAGZ

10

SINT

60

(SEE PAGE 4-31)

Q440

LED

DRIVE

S442 S443

IC002

/SERIAL TRANSFER CONTROL

44

SI

CAR L+

CAR L-

ANT L SW

MD L

CAR S+

CAR S-

ANT S SW

MD S

CN441

27
23

20
21

19RD

31
29

37
36

15XTAL

14EXTAL

1
2
3
4
5

JOGREC

43
42

5

4

41
40

7

SO
CLK

RST

ANT SEL

REQ
TOTAGZ
SINT

D440

JOG

IC001

PLAY
STOP

COM
DMS 2
DMS 1

X001

13.56MHz

S1

DUAL MODE

SHUTTLE

PLAY

STOP

Q001-003,005

Q007,010,016,017

(FRONT)

SMARTFILE

SENSOR

Q004,006,008,009
Q011,012,018,019

(INNER)

SMARTFILE

SENSOR/WRITER

CN001

CN002

3-9 3-10

SLV-M10HF

3-6. TUNER BLOCK DIAGRAM

MA-335 BOARD

(SEE PAGE 4-23)

IN

VHF/

UHF

OUT

CH 4

CH 3

S701

RF CH

TUNER/MOD/IF

2

TU700

SPLITTER

TV

VTR

RF

MOD

51 4

SW5V30V

18 19 3

5V

30V

RF

MPX

AFT

ENABLE

CLOCK

20 2122

IF

L704

L703

5V

DATA

L731

36

35

33

RV731

SEPARATION

IC733

ST/BILINGUAL

PROCESSOR

1

VCC

12

MPX IN

MS0
MS1

TU VIDEO IC201

32

TO

VIDEO

BLOCK

(SEE PAGE 3-3)

L

3

R

4

TU AUDIO L IC360

TU AUDIO R IC360

1

2

TO

AUDIO

BLOCK

(SEE PAGE 3-8)

11ST IND
10SAP IND

8
5

STEREO CN162
SAP CN162

MAIN/SAP CN162

4

17
16

FROM

VIDEO

BLOCK

(SEE PAGE 3-4)

FROM

AUDIO

BLOCK

(SEE PAGE 3-8)

16

Q560

IC360

12

RF VIDEO

RF AUDIO

F MONO

MUTE

Q731

7
5

F MONO IC161
TA MUTE IC161

50
11

FROM/TO

SYSCON

BLOCK

(SEE PAGE

TU AFT CN162

PLL DATA CN162
PLL CLOCK CN162
PLL ENABLE CN162

TV/VTR IC161

11

3-6)

13
14
15

26

3-11 3-12

3-7. POWER SUPPLY BLOCK DIAGRAM

SLV-M10HF

POWER

BLOCK

MA-335 BOARD

CN603

30V

11

9

13V

.

10

4

6V

.

5

+F

1

-F(0V)

2

-30V

3

(SEE PAGE4-5,8,11,15,19,21,23,25)

L604

+30V

IC601

4

REG

SW12V

21

P CONT 2

P CONT 2

SW5V

SW5V

SW5V

D6V

M12V

M12V

P CONT 2

-30V

F+

PS600

L607
L605
L606

12V

REG

Q603,606

SW 5V

JS609

Q604,605

MOTOR

12V SW

IC002

MANCHESTER

CODE MOD./DEMOD.

/SERIAL TRANSFER CONT.

6

VDD

16

VDD

28

VDD

38

VDD

IC001

L004

AMP

8

V+

D005

IC460

TIMER/TUNER

MODE CONT.

24

AVDD

35

AVREF

72

VDD

75

VPP

43

VFDP

78

POWER CONT 1

79

POWER CONT 2

IC462

EEPROM

8

VCC

IC463

RESET

5

VCC2

PULSE

GEN.

POWER

7

VCC1

FAIL

DET.

IC003

SMARTFILE

CONTROL

72

VDD

73

N.C

37

AVREF

IC004

EEPROM

8

VCC

NL-2 BOARD

(SEE PAGE 4-37)

FR-139 BOARD

(SEE PAGE 4-29)

IC464

REMOTE

CONTROL

RECEIVER

2

VCC

ND420

FLUORESCENT

INDICATOR TUBE

D420

F-F+

IC160

IC733

ST/BILNG

PROCESSOR

VCC

1

IC201

Y/C PROC.

36

Y VCC

47

C VCC

IC202

1H DELAY

2

VDD

L301

(1/2)

IC201

AUDIO PROC.

(MONO)

76

IC100

DRUM

CAPSTAN

8

Q101,102

SENSOR

PH100,101

REEL

L502

L503

AVCC

AMP
VCC

T/S

T/S

(2/2)

4
7

13

IC500

OSD
AVCC

VCC

IC501

AFC

VCC

CN165

SW12V

D 6V

CN163

D 6V

CN162

D 6V

P CONT 1
P CONT 2

-30V
+F

-F

SMARTFILE

SENSOR BLOCK

L008

L007

L006

L003

L002

L009

L010

CN003

CN460

PS001

PS002

L182

D462

D464

SMART

FILE

D460

POWER

ON

D463

D5V

6

CN461

D008

D008

4

4

3

3

CHECK

4

PIN

24
25

21
22

29
30
31

8

.

.

7

11
10

3
2
1

TU700

5V

5V

R705

30V

30V

18

3

L703

L704

5V

32

19

L731

L204

IC260

L202

L263

VIDEO

REC/PB AMP

16

VCC

29

VCC

L206

IC340

L331

T331,Q331

BIAS

ERASE

OSC

L341

REC/PB AMP

REC/PB AMP

14

IC301

HEAD SW

1

VCC

AFM

VCC

IC360

AUDIO PROC.

(HIFI)

35

12V

IC871

SYNC

DET/SET

F-

D161

D161

20

L160

VDD

SERVO/SYSTEM

CONTROL

53

AVREF

54

AVDD

89

VDD

90

5V

IC980

SIRCS/CBC

I/O

14

D982

13

REG IN

VCC

IC140

PS101

CTL AMP

8

VCC

IC141

CTL AMP

8

VCC

D109

CN101

MTR 12V

CN102

MTR 12V

SW 5V

1

7
1

DRUM

MOTOR

CAPSTAN

MOTOR

L101

IC161

LOADING

MOTOR

DRIVE

8

VCC1

9

VCC2

L140

L141

16

DM-81 BOARD

(SEE PAGE 4-31)

CN440

6

Q440

Q440

LED

DRIVE

D440

JOG

3-13 3-14E

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM

SECTION 4

SLV-M10HF

4-1 4-2

FRAME SCHEMA TIC DIAGRAM

MA-335 (REC/PB AMP) SCHEMATIC DIAGRAM

— Ref. No.: MA-335 Board; 1,000 Series —

SLV-M10HF

MA-335 BOARD

CJ570 A-3
CN101 C-7

CN102 E-2
CN103 I-4
CN162 J-12
CN163 I-12
CN165 G-11
CN260 B-9
CN261 B-7
CN301 B-4
CN302 B-5
CN341 B-10
CN423 C-12
CN603 H-1

CNJ980 A-2
CNJ981 A-1

D103 F-6
D107 G-8
D109 F-4
D161 J-8
D370 C-10
D379 A-11
D502 C-1
D503 C-2
D504 C-2
D560 B-3
D561 A-10
D611 J-3
D612 J-3
D614 J-3
D702 F-12
D801 D-9
D802 D-9
D980 A-2
D981 A-2

D982 B-1
D983 A-1
D984 A-1

IC100 G-6
IC101 I-3
IC140 H-11
IC141 A-5
IC161 I-9
IC201 D-5
IC202 E-5
IC260 B-8
IC301 B-5
IC340 B-10
IC360 B-11
IC500 C-1
IC501 D-1
IC601 E-12
IC733 H-13
IC871 I-6
IC980 B-1

PH101 H-8
PH102 H-4

Q101 F-1
Q102 F-10
Q103 F-5
Q140 H-10
Q201 C-3
Q204 C-3
Q205 C-3
Q208 D-4
Q209 E-4
Q210 E-5
Q211 D-6
Q214 D-6
Q260 B-7

Q301 C-5
Q331 C-6
Q379 A-11
Q386 A-11
Q387 A-11
Q502 B-2
Q503 B-2
Q505 D-1
Q560 B-3
Q603 J-2
Q604 J-3
Q605 J-4
Q606 J-2
Q731 H-13
Q801 B-8
Q802 E-10
Q803 E-9
Q804 E-9
Q805 E-9
Q806 E-8
Q807 E-8
Q808 E-8
Q809 D-8
Q810 E-8
Q851 C-8
Q852 C-8
Q853 D-8
Q854 D-8
Q855 D-8
Q856 D-8
Q857 D-8
Q871 I-5
Q872 I-5
Q873 I-5
Q874 I-5
Q875 H-5

MA-335

1

2

BOARD

IC260 4 REC

1V/Div

0.1µsec/div

IC260 #º REC

CN261 1 REC

0.5V/Div

0.1µsec/div

3

IC260 @• REC

20mV/Div

0.1µsec/div

4

IC260 @™ PB

200mV/Div

0.1µsec/div

5

IC260 !• REC/PB

H

2.3Vp-p

DC PB

SP CH1
REC BIAS
SP CH1
PRE AMP IN
SP CH1
REC AMP
OUT SP
PRE AMP IN
SP CH2

REC BIAS

SP CH2
DC PB
SP CH2

GND
DC PB

EP CH2
REC BIAS

EP CH2
PRE AMP IN

EP CH2
REC AMP
OUT EP
PRE AMP IN
EP CH1
REC BIAS
EP CH1
DC PB
EP CH1

REC CURR.

MAIN VCC

REC Y+C IN
PB FM AGC

ENV DET

AGC DET

PB FM AGC

PRE AMP OUT

REC AMP IDLE ADJ

CHROMA 30

SSB CLK

SSB DATA

SYNC IN
SW30 IN

THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)

• For printed wiring boards.

• b : Pattern from the side which enables seeing.

Caution :

Pattern face side: Parts on the pattern face side

DET

OUT
OUT

IN

GND

OUT

VCC

(Conductor Side) seen from the pattern face are

indicated.
Pattern face side: parts on the parts face side seen
(Component Side) from the parts face are indicated.

• For schematic diagrams.

• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, because it is damaged by the heat.

• All resistor are in ohms, 1/4W unless otherwise noted.
Chip resistor are 1/10W unless otherwise noted.
kΩ: 1000Ω, MΩ, : 1000kΩ.

• All capacitors are in µF unless otherwise noted. pF : µ
µF . 50V or less are not indicated except for electrolytics
and tantalums.

• C: panel designation.

•

: internal component.

• A: B+ Line. *

• B: B– Line. *

• J : IN/OUT direction of (+,–) B LINE. *

• Circled numbers refer to waveforms. *

• Readings are taken with a color-bar signal input.

• Voltage are dc between ground and measurement
points.*

• Readings are taken with a digital multimeter (DC10MΩ).*

• Voltage variations may be noted due to normal production
tolerances.*

MA-335
REC/PB AMP , VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER

AJ-2
(LINE-2 IN)

AN-17
FRONT
SMARTFILE
SENSOR

FR-139
(MODE CONTROL)

NL-2
(SMARTFILE)

AN-16
INNER SMARTFILE
SENSOR/WRITER

POWER BLOCK SR821

DM-81
(OPERATION SWITCHES)

6

IC260 !¶ REC/PB

CN261 3 REC/PB

5Vp-p
30Hz

4-5

NC

PSW1

EP/SP

A-HEAD PULSE

FILT1

PB-FM OUT

PB GND

RECMUTE

CH2-IN

REC

FILT2

PSW2

CH1-IN

GND

BUFF IN

BUFF OUT

REC OUT

REC FM IN

REC BIAS

AGC FILT

VCC

REC MODE

REC-CURR-ADJ

REC OUT GND

4-6 4-7

When indicating parts by reference number, please
include the board name.

• * : indicated by the color red.

REC/PB AMP

MA-335 (1/10)

SLV-M10HF

MA-335 (VIDEO, NORMAL AUDIO) SCHEMATIC DIAGRAM

— Ref. No.: MA-335 Board; 1,000 Series —

• See page 4-3 for MA-335 BOARD printed wiring board.

MA-335

7

BOARD

IC201 !∞ PB

CN261 2 PB

200mV/Div 0.1µsec/div

8

IC201 @º PB

0.1V/div

0.1µsec/div

9

IC201 @∞ REC

H

!º

IC201 @• REC

H

!¡

IC201 #∞ REC

0.5Vp-p

1Vp-p

!£

IC201 #• REC/ PB

H

!¢

IC201 $∞ PB

H

!∞

IC201 %§ REC

3.579545MHz
550mVp-p

!∞

IC201 %§ PB

3.579545MHz
500mVp-p

!§

IC201 $• REC

IC201 %º REC

2Vp-p

500mVp-p

SECAM DET
/S-DET OUT

C-ROT
PULSE-IN

HEAD SW
PULSE IN

S-DET LPF

S-DET ADJ

MUTE ON/OFF

LINE-IN 1

ALC-DET

LINE-IN 2

VREF FILTER

LINE-IN 3

A-VCC

LINE-OUT

ALC DET IN

REC-IN

AUDIO HEAD
SW OUT

SERIAL

DATA IN

REC-OUT

SERIAL

CLOCK IN

A-GND

OUT

ACK/SLD

AUTO-BIAS-IN

KILL-FILT

EQ-SW2

IN

VXO2/XO2

AUTO-BIAS-C

OUT 2

VXO2/XO2

AUTO-BIAS-B

OR PB-H OUT

VXO2/XO2 OUT 1

EQ-IN

C-GND

EQ-NFB

OUT

VXO1/XO1

EQ-SW1

IN

VXO1/XO1

EQ-OUT

FILTER

REC-APC

LINE-PB-IN

TR-SW

PA STOP

C-CCD IN

AFC/APC FILT

C-CCD DRIVE 1

ACC-FILT

REC-C-OUT

AGC-TC1/

PB Y FM/C-IN

CARRIERLEAK BALANCER

SLD-FILT

EQ-FILT

C VCC

C-CCD DRIVE 2

PB-EQ-OUT

REC-Y FM-OUT

PB CHROMA IN

PB CHROMA OUT

REC-H-OUT

PB Y-FM-IN

2fsc OUT

PB APC 2

NTSC-H OUT

AGC-TC2

TRICK-H OUT

60Hz-H OUT

Y CCD-DRIVE

VCA-IN

(CLAMP)
VCZ-FILT

VIDEO-OUT

SYNC-OUT

Y-VCC

VIDEO AGC IN

VPS OUT

QV, QH-INS
CHARA-INS

VIDEO-IN 3

REG

VIDEO-IN 2

FBC-FILT

VIDEO-IN 1

Y GND

CLAMP IN

REC-Y

MAIN DE-EMPH.

OUT

PB EMITTER PEAKING

MAIN-EMPH

FILTER

1Vp-p

4Vp-p

!™

IC201 #¶ REC/PB

H

H

VIDEO, NORMAL AUDIO

MA-335 (2/10)

H

!§

IC201 $• PB

IC201 %º PB

H

340mVp-p

0.23Vp-p

4-8 4-9 4-10

SLV-M10HF

MA-335 (SERVO/SYSTEM CONTROL) SCHEMATIC DIAGRAM

— Ref. No.: MA-335 Board; 1,000 Series —

• See page 4-3 for MA-335 BOARD printed wiring board.

MA-335

!¶

IC161 1 REC/PB

!•

IC161



!ª

IC161 $£ REC/PB

@º

IC161 &º REC/ PB

BOARD

100

5Vp-p
30Hz

3Vp-p
16MHz

5Vp-p

1.078kHz

@£

IC161 ^• REC/PB

@¢

IC161 ^ª REC/PB

5Vp-p 360Hz

@∞

IC161 7 REC

4Vp-p 30Hz

5Vp-p
30Hz

@¡

IC161 &£ REC/PB

@™

IC161 &¢ REC/PB

5Vp-p
360Hz

5Vp-p
360Hz

@§

IC161 ^¶ REC

5Vp-p
30Hz

4-11 4-12 4-13

SERVO/SYSTEM CONTROL

MA-335 (3/10)

SLV-M10HF

SLV-M10HF

MA-335 (ON SCREEN DISPLAY) SCHEMATIC DIAGRAM

— Ref. No.: MA-335 Board; 1,000 Series —

• See page 4-3 for MA-335 BOARD printed wiring board.

ON SCREEN DISPLAY

MA-335 (4/10)

MA-335

@¶

BOARD

IC501 !º REC/PB

503.5kHz

0.65Vp-p

4-15 4-16

@•

IC500 9 REC/PB

5Vp-p

14.31818MHz

@ª

IC500 3, @∞ REC/PB

H

2Vp-p

SLV-M10HF

MA-335 (DSF) SCHEMATIC DIAGRAM

— Ref. No.: MA-335 Board; 1,000 Series —

• See page 4-3 for MA-335 BOARD printed wiring board.

4-17 4-18

MA-335

#º Q802

0.2V/div

0.1µsec/div

BOARD

B PB

#¡ Q810 E PB

0.1V/div

0.1µsec/div

DSF

MA-335 (5/10)

SLV-M10HF

MA-335 (V-SET) SCHEMATIC DIAGRAM

— Ref. No.: MA-335 Board; 1,000 Series —

• See page 4-3 for MA-335 BOARD printed wiring board.

V-SET

MA-335 (6/10)

4-19 4-20

MA-335

#™

IC871 #º REC/PB

4.8Vp-p
8MHz

BOARD

SLV-M10HF

MA-335 (AFM AUDIO) SCHEMATIC DIAGRAM

— Ref. No.: MA-335 Board; 1,000 Series —

• See page 4-3 for MA-335 BOARD printed wiring board.

4-21 4-22

AFM AUDIO

MA-335 (7/10)

SLV-M10HF

MA-335 (TUNER) SCHEMATIC DIAGRAM

— Ref. No.: MA-335 Board; 1,000 Series —

• See page 4-3 for MA-335 BOARD printed wiring board.

TUNER

MA-335 (8/10)

4-23 4-24

SLV-M10HF

MA-335 (POWER SUPPLY, AV-BUS) SCHEMATIC DIAGRAM

— Ref. No.: MA-335 Board; 1,000 Series —

• See page 4-3 for MA-335 BOARD printed wiring board.

4-25 4-26

POWER SUPPL Y, A V -BUS

MA-335 (9/10) (10/10)

FR-139 (MODE CONTROL) SCHEMATIC DIAGRAM

— Ref. No.: FR-139 Board; 2,000 Series —

SLV-M10HF

4-29 4-30

MODE CONTROL

FR-139

SLV-M10HF

There are few cases that the part printed on this diagram isn’t mounted in this model.

DM-81 (OPERATION SWITCHES) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM

— Ref. No.: DM-81 Board; 2,000 Series —

There are few cases that the part printed on this diagram isn’t mounted in this model.

AJ-2 (LINE-2 IN) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM

— Ref. No.: AJ-2 Board; 3,000 Series —

MA-335
REC/PB AMP , VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER

AJ-2
(LINE-2 IN)

AN-17
FRONT
SMARTFILE
SENSOR

FR-139
(MODE CONTROL)

DM-81
(OPERATION SWITCHES)

OPERATION SWITCHES

DM-81

NL-2
(SMARTFILE)

AN-16
INNER SMARTFILE
SENSOR/WRITER

POWER BLOCK SR821

4-31 4-32

AJ-2

LINE-2 IN

SLV-M10HF

AN-16 (INNER SMARTFILE SENSOR/WRITER), AN-17 (FRONT SMARTFILE SENSOR) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

— Ref. No.: AN-16, AN-17 Board; 3,000 Series —

There are few cases that the part printed on this diagram isn’t mounted in this model.

MA-335
REC/PB AMP , VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER

AJ-2
(LINE-2 IN)

AN-17
FRONT
SMARTFILE
SENSOR

FR-139
(MODE CONTROL)

NL-2
(SMARTFILE)

AN-16
INNER SMARTFILE
SENSOR/WRITER

POWER BLOCK SR821

DM-81
(OPERATION SWITCHES)

4-33

INNER SMARTFILE SENSOR/WRITER, FRONT SMARTFILE SENSOR

AN-16, AN-17

NL-2 (SMARTFILE) SCHEMATIC DIAGRAM

— Ref. No.: NL-2 Board; 3,000 Series —

SLV-M10HF

4-37 4-38

SMARTFILE

NL-2

SLV-M10HF

POWER BLOCK SR821 (SWITCHING REGULATOR) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM

— Ref. No.: SR821 Board; 9,000 Series —

12345

6

POWER BLOCK (SR821)

A

R106

C109

0.033
400

Q101,102

SWITCHING

D103

ERA15-02

*R109 D104

D102

EG01

Q101

2SC4054

C110

0.047

*R107

D105

1SS119

RD3.0ES

33K/3

FB1

C

D

E

B

AC IN

120VAC

L

H

CN101

F101

2A 125V

C101

0.1/250

R101

6.8M
1/2

L101

C103

470P/125

C102

0.1/250

C104
470P

125

D107-110

1N4005

D110

D108

D109

D107

C105

1500P

125

GND

+

Q102

2SC4040

C106

120/200

R104

10K

C112

0.0047

C111

0.047

D106

1N4005

R102

100K

R103

100K

C107

4.7/50

PC101

ON3131

7

T101 POWER TRANSFORMER

P1

P2

B1

R108

22

B2

There are few cases that the part printed on this diagram isn’t mounted in this model.

8910

S5

S4

S3

IC201

SHUNT REG.

S1

PC101

ON3131

S6

S8

D201

PR1003

D202

S3L20U

D204

D3S4M

C204

2200/16

AN1431T

D206
PR1003

C202

1000/16

C208

1/50

+

R205

R201

10 1/2

C201

47/50

+ +

D205

RD51F

+

*R207

R206

VR201
47
1/2

500

1.8K

R208

1/2

C203

220/16

C205

470/10

C206

47/50

10

L202

20uH

L203

20uH

+

+

C209

0.01

R210

1.5K

0.5W

11

CN201

11

10

9
8
7
6
5
4

3
2
1

+38
+13

+13
GND
GND
GND

+6V

+6V

-30V

-F(0V)

+F(4.5V)

12

TO

MA-335 BOARD

CN603

(SEE PAGE 4-25)

F

16

Note :

The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.

MA-335
REC/PB AMP , VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER

AJ-2
(LINE-2 IN)

AN-17
FRONT
SMARTFILE
SENSOR

FR-139
(MODE CONTROL)

Note :

Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.

NL-2
(SMARTFILE)

AN-16
INNER SMARTFILE
SENSOR/WRITER

POWER BLOCK SR821

DM-81
(OPERATION SWITCHES)

Ref. No min typ max

R107
R109
R207

100/1 120/1

560

1.2k

620

1.5k

120/1

680

2.2k
S7

D207
PR1003

R204

0.47

+

C207

470/10

R209

2.7

SWITCHING REGULATOR

POWER BLOCK SR821

4-39 4-40E

SECTION 5

INTERFACE, IC PIN FUNCTION DESCRIPTION

L

H

*1

*7

*8

*10

H/L

Hi-Z

*1

*1

*7*6*9

*10

Hi-Z

REC PAUSE

REC

Hi-Z

*1

Hi-Z (O.D)

L

Hi-Z (O.D)

SLV-M10HF

*1L*5

REC PAUSE

*1L*5

REC

*1*3*5

REVIEW

*1*3*5

CUE

*1*2*5

x 2

*1*3*5

SLOW

*1*3*5

PB PAUSE

*1*2*5

PB

L

L

L

L

L

L

L

L

REVIEW

x 2

CUE

SLOW

PB PAUSE

PB

TAPE

TAPE

L

Hi-Z

Hi-Z (O.D)

L

Hi-Z

Hi-Z (O.D)

L

Hi-Z

Hi-Z (O.D)

*3*2*2

Hi-Z

L

L

Hi-Z

L

Hi-Z

Hi-Z (O.D)

L

Hi-Z

Hi-Z (O.D)

UNTHREADING

L

Hi-Z

Hi-Z (O.D)

THREADING

*6

*1*7*6

*6

*1*7*6

*6

*1*7*6

*1*7*2

*1

*7

H/L

H/L

*1*1*7*6*9

*5*5*5

*5*5*5

*9

*10

Hi-Z

*8

*10

Hi-Z

*9

*10

Hi-Z

*8

*10

*11

*8

*10

Hi-Z

*10

Hi-Z

*8

*10

Hi-Z

*8

*10

Hi-Z

L

*1L*5

TAPE

UNTHREADING

L

L

*1

THREADING

L

*1

FF/REW

O

OIO

14^§

RF SWP

QVD

*5

L

*4

!£

V SYNC

NT JUDGE

*1 Synchronized with drum rotation. 30Hz 50% duty cycle.

*2 Normally “L“. “H“ when CTL signal is not generated.

*3 V period “H“ pulse.

*4 Selected by REC mode. “H“ in LP mode.“

*5 Composite sync signal (positive).

5-2. SYSTEM CONTROL — SERVO PERIPHERAL CIRCUIT INTERFACE (MA-335 BOARD IC161)

TAPE

STOP

I/O

Pin No.

Signal

5-1. SYSTEM CONTROL — VIDEO BLOCK INTERFACE (MA-335 BOARD IC161)

L

*6*1*7*6*8

Hi-Z

REW

Hi-Z (O.D)

L

FF

STOP

I/O

Pin No.

Signal

*6*1*7*6*8

Hi-Z

Hi-Z (O.D)

L

L

H

Hi-Z

III

O

O

O (O.D)

7#∞(ª^¶^•^ª&º

REC CTL

CAP STOP

STEP PLS

PB CTL

*4

*4

DRM PG

DRM FG

*8

H/L

I

O

&£&¢8

CAP FG

CAP DA

5-1

*10

Hi-Z

*10

Hi-Z

*10

Hi-Z

O

I/O

DRM DA

CTL RESET

*1. 30Hz pulse.

*2. Pulse at tape running.

*3. Reverse logic pulse of STEP PLS.

*4. “L” when drum rotation stops.

*5. Unstable period pulse.

*6. Pulse in period in proportional to tape speed.

*7. 360Hz pulse.

*8. Pulse at tape running.

*9. Approx. 2 msec period “H” or “L” pulse.

*10. Approx. 1.5 msec period “H” or “L” pulse.

*11. “L” when FWD SLOW, “H” when RVS SLOW.

REC

PAUSE

LLL

H

*7

*2

H/L

H/L

L

L

*4

*6

*6

*7

REC

*7

REVIEW

*7

CUE

*7

x 2

*7

SLOW

*7

PB PAUSE

*7

PB

*7

REW

*7

FF

H

L

H

H

H

H

H

H

H

LLL

L

H

L

L

LLL

LLL

LLL

L

L

L

H

L

H

L

L

H

H

H

*2*3*3

*2*3*3

*2*3*3

*2*3*3

*2*3*3

*2

H/L

*2*3*3

*2*3*3

*2*3*3

H/L

L

H

*4

*6

*6

H

H

*4

*6

*6

L

H

*4

*6

*6

L

H

*4

*6

*6

*4

*5

*6

*6

L/*5

L

L

*4

*6

*6

L

H

*4

*6

*6

H

H

*4

*6

*6

L

H

*4

*6

*6

REC PAUSE

REC

REVIEW

CUE

x 2

SLOW

L

L

H

*1

L

L

H

*1

L

H

H

*1

L

H

H

*1

L

H

H

*1

L

H

H

*1

H

*7

STOP

L

*1*1*1*1*2

TAPE

UNTHREADING

H

*1*1*1*1*2

TAPE

THREADING

LLL

UNLOADING

CASSETTE

LLL

H

LOADING

CASSETTE

L

H

EJECTED

IIIII

I/O

HI-Z

9@™@¡@º!ª!∞^¢

Pin No.

L

H

H

*2

L

H

*2

H

*2

L

L

H

H

*4

H/L

H/L

*3

*4

H/L

*3

*4

H/L

*4

H/L

H/L

*4

H/L

H/L

*4

H/L

H/L

I

I

O (O.D)

^£#™#∞&™^¡

L

H/L

H

H

L

H

L

L

L

H

O

O (O.D)

*6

*6

PB PAUSE

*6

*6

PB

When transition to LOADING direction : “H”.

When CAM MOTOR is stopped : Hi-Z.

When RVS slow : Mode 2=”L”

When RVS slow : Mode 3=”H”

When RVS slow : Mode 4=”L”

*7. When transition to UNLOADING direction : “L”.

*6

*6

*4

*4

*4

*4

*4

*4

I

I

^™

*8. When RVS slow : Mode 1=”L”

I/O Level

Normally “H”, “L” when service interruption is detected or restored.

Chip select signal from timer microprocessor. V period “L” pulse.

Serial communication data from timer microprocessor. V period “ L” pulse.

Serial communication data to timer microprocessor. V period “L” pulse.

Serial communication clock from timer microprocessor. V period “L” pulse.

I

I

I O I

I/O

$º

$¢

$¶

$∞

Pin No.

$§

TAPE

TAPE

STOP/FF/

I/O

Pin No.

H

*1

L

UNLOADING

L

LOADING

AF RF envelope signal input terminal for automatic tracking.

L

REW

I

O (O.D)

%ª#¡ 2

L

H

*1

L

H

*1

L

H

*1

L

H

*1

L

H

*1

O

O

O (O.D)

`⁄‚‚

#§

Signal

CAM2

MODE 1 (*8)

MODE 2 (*8)

MODE 3 (*8)

MODE 4 (*8)

(IN REC PRF)

T REEL FG

S REEL FG

T/E LED

CAP STOP

CAP RVS

T SENS

5-3. SYSTEM CONTROL — MECHANISM INTERFACE (MA-335 BOARD IC161)

S SENS

Signal

ASURA RESET

ASURA CS

S IN 0

S OUT 0

*1. Uncertainly.

*2. “L” when erasing protection tab is bent. “H” when not bent.

*3. Pause of period in proportion to reel rotating speed.

*4. Approx. 2 msec period “H” pulse.

*5. Pulse at tape running.

*6. Normally “L”. 2 msec period “H” pulse when tape top or tape end is detected.

5-4. SYSTEM CONTROL — SYSTEM CONTROL PERIPHERAL CIRCUIT INTERFACE (MA-335 BOARD IC161)

S CLK

5-2

Signal

AF ENV

A MUTE

AF REC P

AF SWP

FULL ERS

5-5. SYSTEM CONTROL — AUDIO BLOCK INTERFACE (MA-335 BOARD IC161)

*1. 30 Hz 50 % duty pulse approx. 5 msec delayed from RF SW P.

5-6. SERVO/SYSTEM CONTROL MICROPROCESSOR PIN FUNCTIONS

(MA-335 BOARD IC161)

Pin No.

1
2
3
4
5
6
7

8

9
10
11
12
13
14

15
16

17
18
19
20
21
22

23

24
25

26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43

44
45

46
47
48
49
50

Pin Name

RF SWP
AF REC P
N.C.
QVD
AUTO PRESET
FE ON
REC CTL

CTL RESET
CAM 2

N.C.
TA MUTE
S-VHS
NT JUDGE
MESECAM DET

CIN (REC PRF)
AV CONT

SECAM ON
SW1
MODE 4
MODE 3
MODE 2
MODE 1
POWER SAVE
CONT 1
POWER SAVE
C+
MOD CONT
TV/VTR
N.C.
SDA 0
N.C.
SCL 0
A MUTE
T/E LED
N.C.
N.C.
CAP STOP
FULL ERS
N.C.
N.C.
MP
ASURA RESET
VSS
XTAL
EXTAL

ASURA CS
S IN 0

S OUT 0
SCLK
NICOL ON
CBC POWER
F. MONO

I/O

RF switching pulse output.

O

“H” when HiFi audio REC.

O

Not used.

—

Quasi VD pulse output.

O

“H” during auto preset.

O

Flying erase ON/OFF

O

REC CTL signal output.

O

Capstan current control. “H” during

O

slow mode.
Cam motor control.

I

Not used.

—

Tuner audio mute. H: Mute

O

S-VHS tape detection signal in.

I

Not used.

I

Not used.

I

Erasing protection tab, cassette in

I

detection signal input.
Not used.

O

Not used.

—

Not used.

—

Cam encoder signal input.

I

Cam encoder signal input.

I

Cam encoder signal input.

I

Cam encoder signal input.

I

Not used.

O

Not used.

O

Not used.

O

TV/VTR control signal output.

O

Not used.

—

I2C data.

I/O

Not used.

—

I2C clock.

I/O

“H” when audio mute.

O

Tape top/end sensors driver.

O

Not used.

—

Not used.

—

Capstan stop signal output.

O

Full erase control.

O

Not used.

—

Not used.

—

Fixed to “L”.

I

System reset signal.

I

Ground.

—

System clock 16MHz.

O

System clock 16MHz.

I

Servo/system control microcomputer

I

chip select signal.
Serial communication signal.

I

Serial communication signal.

O

Serial communication signal.

I

NICOL control signal out.

O

Cable box control signal out.

O

Forced mono.

O

Function

Pin No.

51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70

71

72
73

74
75
76
77
78
79
80
81
82
83

84
85

86
87
88
89
90
91
92
93
94
95
96
97
98

99

100

Pin Name

SW2
AVSS
AVREF
AVDD
NTPB SW
A V ADJ
FOLLOW TV
N.C.
AF ENV
RF ENV
T SENS
S SENS
S REEL FG
T REEL FG
N.C.
VSYNC
PB CTL
DRM PG
DRM FG
CAP FG
BLUE BACK
ON

CAP RVS
CAP DA

DRM DA
N.C.
N.C.
REC COUNT
C PLUS DET
N.C.
DATA (SSB)
CLOCK (SSB)
N.C.
N.C.

CAP TRQ PWM
N.C.

N.C.
N.C.
VSS
VDD
5V
N.C.
CTL HYS HIGH
N.C.
N.C.
N.C.
AF REC
N.C.
N.C.

STEP PLS
AF SWP

I/O

O

Not used.

—

Unswitched ground.

—

AD port reference input UNSW 5V.

—

UNSW 5V.

I

Not used.

I

Adjustment mode.

I

Not used.

—

Not used.

I

HiFi audio playback signal envelope.

I

Video playback signal envelope.

I

Take-up end sensor.

I

Supply end sensor.

I

Supply reel FG input.

I

Take-up reel FG input.

—

Not used.

I

Composite sync. signal input.

I

Playback CTL input.

I

Drum PG input.

I

Drum FG input.

I

Capstan FG input.

O

Not used.
Capstan reverse control “H” when

O

reverse.

O

Capstan error D/A output.

O

Drum PG output.

—

Not used.

—

Not used.

I

Counter signal input when recording.

O

Not used.

—

Not used.

O

Serial communication data.

O

Serial communication clock.

—

Not used.

—

Not used.
PWM output for capstan torque

O

control.

—

Not used.

—

Not used.

—

Not used.

—

Ground.

—

5V.

—

5V.

—

Not used.

O

CTL amp gain control.

—

Not used.

—

Not used.

—

Not used.

O

“H” output when hifi audio recording.

—

Not used.

—

Not used.
Step pulse “H” when capstan step

O

driving.

O

AF switching pulse output.

Function

5-3

5-7. TUNER/TIMER MODE CONTROL PIN FUNCTIONS (FR-139 BOARD IC460)

Pin No.

1
2

3

4
5

6
7

8
9

10

11

12
13

14
15
16
17
18
19
20
21

22
23

24
25
26

27
28

29
30
31
32
33
34
35
36
37

38
39

40
41
42
43
44
45
46
47
48
49

Pin Name

N.C.
POWER FAIL

H DET

SIRCS IN
STEREO DET

SW1 SIRCS OUT
BUZZER

MUTE
RESET

SCK 0

SI 0

SO 0
EEP WC

LANC IN
LANC OUT
A/D 0
A/D 1
A/D 2
A/D 3
A/D 4
ML LED

X CS
AFT

AVDD
AV REF
SCL 0

CG CS
SDA 0

JOG LED
AVSS
EXTAL
XTAL
VSS
RST
PLL CLK
PLL DATA
PLL ENABLE

MAIN/SAP
SAP DET

V SET CS
DMS 1
DMS 2
VFDP
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6

I/O

I

Not used.

I

Power failure detect signal input.
H DET_(TUNER H SYNC detect

I

input).
Remote control signal (SIRCS)

I

input.

I

Stereo judge input.
Remote control signal (SIRCS)

O

output.

O

Buzzer signal output.

O

MUTE control.

O

Not used.
Serial communication signal (Serial

I

clock).
Serial communication signal (Data

I

input).
Serial communication signal (Data

O

output).

O

EEP mode control.

I

LANC input.

O

LANC output.

I

Analog voltage (KEY) input.

I

Analog voltage (KEY) input.

I

Analog voltage (KEY) Input.

I

Analog voltage (KEY) Input.

I

Analog voltage (KEY) Input.

O

ML LED ON/OFF control.
NL-2 board IC003 chip select

O

signal out.

I

AFT (Auto fine tuning signal input).

I

A/D port reference input.
UNSW 5V.

O

T BUS (clock) /IIC BUS (clock).
Character generator chip select

O

signal.

O

IIC BUS (data).

O

JOG LED control signal output.

I

UNSW ground.
System clock terminal (16MHz).
System clock terminal (16MHz).
Ground.

I

RESET input.

O

TUNER PLL clock.

O

TUNER PLL data.

O

TUNER chip select.
NO USE (MAIN/SAP judge signal

O

output).

O

MAIN/SAP judge input.

O

V SET IC chip select signal.

I

DMS forward/reverse signal input.

I

DMS forward/reverse signal input.

I

VFDP.

O

Segment terminal 1

O

Segment terminal 2

O

Segment terminal 3

O

Segment terminal 4

O

Segment terminal 5

O

Segment terminal 6

Function

Pin No.

50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75

76
77

78
79
80

Pin Name

SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
NC
NC
GRID10
GRID9
GRID8
GRID7
GRID6
GRID5
GRID4
GRID3
GRID2
GRID1
VDD
TX
TEX
NC/VPP

ASURA CS
SYS RESET

POWER CONT 1
POWER CONT 2
CG V

I/O

O

Segment terminal 7

O

Segment terminal 8.

O

Segment terminal 9.

O

Segment terminal 10.

O

Segment terminal 11.

O

Segment terminal 12.

O

Segment terminal 13.

O

Segment terminal 14.

O

Segment terminal 15.

O

Segment terminal 16.
Non Connect.
Non Connect.

O

Grid terminal 10.

O

Grid terminal 9.

O

Grid terminal 8.

O

Grid terminal 7.

O

Grid terminal 6.

O

Grid terminal 5.

O

Grid terminal 4.

O

Grid terminal 3.

O

Grid terminal 2.

O

Grid terminal 1.
D5V
Timer clock terminal (32.768kHz).
Timer clock terminal (32.768kHz).

O

D5V
S/S microcomputer chip select

O

signal.

O

System reset output.

O

Power supply control signal.

O

Power supply control signal.

I

Composite sync input.

Function

5-4E

SECTION 6

White (100%)

About 0.7 V

About

0.3 V

Horizontal sync signal

Red

Burst signal
(It must be flat.)

About

0.3 V

ADJUSTMENTS

SLV-M10HF

6-1 MECHANICAL ADJUSTMENTS

For the mechanical adjustments, please refer to the
“VHS MECHANICAL ADJUSTMENT MANUAL
(S MECHANISM)” (9-921-647-11).

6-2. ELECTRICAL ADJUSTMENTS

See the adjusting parts location diagram from on page 6-8
for the adjustment.

2-1. PREPARATION BEFORE ADJUSTMENT
2-1-1. Equipment Required

The measuring instruments used for this alignment include:

1) Monitor TV

2) Oscilloscope, dual-trace, bandwidth of 30MHz or more, with
delay mode (A probe 10:1 should be used unless otherwise
specified.)

3) Frequency counter

4) Pattern generator

5) Digital voltmeter

6) Audio generator

7) Audio level meter

8) Audio distortion meter

9) Audio attenuator

10) Alignment tapes
KRV-51N2 Part No.: 8-192-605-32

2-1-3. Input Signal Check

Video signal produced by a pattern generator is used as an adjustment
signal to perform electrical alignment for this unit. This video signal
must satisfy the specification.

Unless otherwise specified, place the switches and controls of this
unit in the following positions:

• INPUT SELECT switch ............................. LINE or LINE 1

(Remote commander)

Connect an oscilloscope to the V ideo Input terminal. Check that the
synchronizing signal of the Y signal has an amplitude of
approximately 0.7V and that the burst signal has an amplitude of
approximately 0.3V and its waveform is flat. And check that the
level ratio of burst signal to “red” signal is 0.30 : 0.66. The video
signal (color bar) used for electrical aligning this unit is shown in
Fig. 6-2-2.

2-1-2. Equipment Connection

Unless otherwise specified, connect and adjust the measuring
instruments as shown in the following diagram.

VIDEO LINE IN

Pattern generator VCR

Video output

Ω

)

(75

VIDEO LINE OUT

Monitor TV

Fig. 6-2-1.

Fig. 6-2-2. Color Bar Signals of Pattern Generator

2-1-4. Alignment Tape

• Contents of KRV-51N2

Audio signal

Hi-Fi

400Hz

1
2
3
4

Mode

SP

EP

Period

7 minutes
3 minutes
7 minutes
3 minutes

Video signal

Color bar

Monoscope

Color bar

Monoscope

Normal

400Hz

6-1

2-1-5. Input/Output Levels and Impedance

Video input: LINE IN

Input signal: 1Vp-p, 75ohms, unbalanced,
sync negative

Video output: LINE OUT

Output signal: 1Vp-p, 75ohms, unbalanced,
sync negative

Audio input: LINE IN

Input level: –7.5 dBs
(0dBs= 0.775Vrms)
Input impedance: more than 47 kilohms

Audio output: LINE OUT

Standard level: –7.5dBs at load impedance 47
kilohms
Output impedance: less than 10 kilohms

2-1-6. Adjustment Sequence

The adjustments should be performed in the following sequence.

Power Supply Check

Servo System Adjustments

2-2. POWER SUPPLY CHECK
2-2-1. Output Voltage Check (MA-335 Board)

Mode E-E
Measuring Instrument Digital voltmeter
SW 12V Check
Measurement point IC601 pin 2
Specified value 12.0 ± 0.3V
MTR12V Check
Measurement point Q605 C
Specified value 13.2 ± 1.0V
SW5V Check
Measurement point Q603 E
Specified value 5.1 ± 0.3V

[Check Method]

1) Each of these supply voltages must meet its specified value.

Audio System Adjustments

Video System Adjustments

Tuner System Adjustments

6-2

2-3. SERVO SYSTEM CHECK

CH2
RF SWP
CN261 pin

3

CH1
REC AFM
CN341
pin

1

OK

NG

Should be minimized

RF signal dropout

Unless otherwise specified, set the switches to the following
positions.

• INPUT SELECT switch ........................................... LINE 1

•

TAPE SPEED

switch ..................... SP (Remote commander)

2-3-1. RF Switching Position/

AF Switching Position Adjustments
(MA-335 Board)

[Adjustment Purpose]

T o adjust the link of the A-ch and B-ch of the tape playback outputs.
To make the unit compatible with other tapes and units. If this
specification is not satisfied, the link will appear on the screen and
the screen will be disrupted, etc.

Mode Playback
Signal Alignment tape: SP color bar portion
Measurement point CH1: Video LINE OUT

(RF switching position)
CN341 pin 1 (HF ADJ)
(AF switching position)

CH2: CN261 pin 3 (RF SWP)

Measuring instrument Oscilloscope
Specified value 6.5 ± 0.5H (410 ± 32 µsec)

[Adjustment Method]

1) Short-circuit between JS161 and ground for about 1 second to
activate the RF switching position adjustment mode.

2) Check that “AP” is indicated on FL display.

3) Using the channel + and – buttons, adjust to 410 ± 32 µsec (6.5
± 0.5H).

4) Press the P AUSE b utton. (Adjustment is over for mono models.)

5) The set goes to the AF switching position adjustment mode.

CH1

CH2

CH1

CH2

CN261 pin

V

Enlarrgement

Vertical sync. signal

6.5 ± 0.5H

3

Approx.
1Vp-p

Approx.
5Vp-p

6) Check that “AH” is indicated on FL display.

7) Using the channel + and – buttons, minimize a chipped portion.
At this time, confirm that a noisy sound is not heard.

8) Press the PAUSE button.

9) Check that “AH” indication is disappeared. When it is not
disappeared, repeat from the item 1).

10) Press the STOP button.

11) Press the EJECT button.

Fig. 6-2-3.

Fig. 6-2-4.

6-3

2-4. VIDEO SYSTEM CHECKS

For the video system checks, follow the checking procedures giv en
below as a rule. The color bar video signal supplied from the pattern
generator is used as the video input signal for the video system
adjustment of the recording mode. Check that the signal satisfies
the specified value designated in the “Check of input signal” (Fig.
6-2-2)
Unless otherwise specified, set the switches to the following
positions.

• INPUT SELECT switch ........................................... LINE 1

•

TAPE SPEED

switch ..................... SP (Remote commander)

2-4-2. SYNC AGC Check (MA-335 Board)

Mode E-E
Signal Color bar
Measurement point IC201 pin #•
Measuring instrument Oscilloscope
Specified value A=2.10 ± 0.10Vp-p

[Check Method]

1) Check that the Video signal level (A) satisfies the specified
value.

[Checking Sequence]

1) X’tal OSC Check

2) SYNC AGC Check

3) Recording Y Level Check

4) Recording Chroma Level Check

5) Playback Level Check

2-4-1. X’tal OSC Check (MA-335 Board)

Mode Playback
Signal Alignment tape: SP Color bar portion
Measurement point IC201 pin %§
Measuring instrument Oscilloscope and Frequency counter
Specified value 3,579,545 ± 70Hz

Note: A frequency counter should be connected through a buffer

amplifier (oscilloscope, etc.) having a high impedance and
a low capacitance.

[Check Method]

1) Check that the oscillation frequency satisfies the specified value
and that the oscillation voltage is 500 ± 200mVp-p.

500 ± 200mVp-p

White (100%)

A

H

Fig. 6-2-6.

2-4-3. Recording Y Level Check (MA-335 Board)

Mode E-E (SP)
Signal No-signal
Measurement point IC201 pin !•
Measuring instrument Oscilloscope
Specified value A=290 ± 70mVp-p

[Check Method]

1) Check that the recording RF signal satisfies the specified value.

A

3,579,545

±

70Hz

Fig. 6-2-5.

Fig. 6-2-8.

6-4

2-4-4. Recording Chroma Level Check

VTR

Audio line OUTPUT L/R

Audio line INPUT L/R

Audio

oscillator

Attenuator

600

Ω

Audio level

meter

or

distortion

meter

47 k

Ω

(MA-335 Board)

Mode Recording (SP)
Signal Color bar
Measurement point IC201 pin !¢
Measuring instrument Oscilloscope
Specified value A=450 ± 70mVp-p

[Check Method]

1) Confirm the amplitude of recording chroma level becomes the
specified value.

2-5. AUDIO SYSTEM ADJUSTMENT

• For the adjustment of the audio system, perform in the SP mode
if there is no special notes. Use the alignment tape.

[Connecting Instruments]

A

Fig. 6-2-9.

2-4-5. Playback Level Check (MA-335 Board)

Mode Playback
Signal Alignment Alignment tape : SP mode color bar

portion
Measurement point Video LINE OUT terminal
Measuring instrument Oscilloscope
Specified value A=1.0 ± 0.1Vp-p (75Ω terminated)

[Check Method]

1) Check that the playback level satisfies the specified value.

White (100%)

A

Fig. 6-2-11.

• Adjust in the SP mode if there is no special indications.

• Perf orm the adjustment setting the switch on the following
positions.

• INPUT SELECT switch ............................................ LINE 1

[Adjustment Method]

1. ACE head adjustment.....Refer to the VHS mechanical

adjustment manual (S MECHANISM)(9-921-647-11).

2. E-E output level check

3. Overall Output level and distortion factor check

4. Overall noise level check.

2-5-1. ACE Head Adjustment

Refer to the VHS mechanical adjustment manual

(S

MECHANISM)(9-921-647-11).

2-5-2. E-E Output Level Check

Mode E-E
Signal 400Hz, –7.5dBs : CJ570
Measurement point CJ570
Measuring instrument Audio level meter
Specified value –7.5 ± 2dBs

H

Fig. 6-2-10.

[Check Method]

1) Input signal of 400Hz and –7.5dBs to the CJ461 L/R.

2) Check that the audio output level is –7.5 ± 3dBs.

6-5

2-5-3. Overall Output Level and Distortion Factor

Check

Mode Self-record playback
Signal 400Hz, –7.5dBs : CJ570
Measurement point CJ570
Measuring instrument Audio level meter and Distortion

meter

Specified value Playback Level: –7.5 ± 3dBs

Distortion: 4.0% or less

[Check Method]

1) Input signal of 400Hz and –7.5dBs to the audio input.

2) Record signal.

3) Playback the recorded portion.

4) Check that the output level is –7.5 ± 3dBs.

5) Check that the distortion factor is 4.0% or less.

2-5-4. Overall Noise Level Check

Mode Self-record playback
Signal No signal (Insert a shorting plug into

the Audio LINE IN terminal)
Measurement point CJ570
Measuring instrument Audio level meter
Specified value – 45.5dBs or less

[Check Method]

1) Record.

2) Playback recorded portion.

3) Check that noise level is – 45.5dBs or less.

2-6. TUNER SYSTEM ADJUSTMENT
2-6-1. Separation Adjustment (MA-335 Board)

Mode E-E
Signal RF signal

Video : Color bar

white (100%) modulation

Audio : L: 400Hz, R: 2kHz

30% modulation

Electrical field:

60-80dBm/75Ω terminated

Measuring instrument Audio level meter
Measuring point LINE OUT L
Adjusting element RV731
Specified value 2kHz component minimum

[Adjustment Method]

1) Connect an audio level meter to LINE OUT L channel via HPF.

2) Feed the RF signal from RF IN terminal.

3) Adjust with R V731 so that the output level satisf ies the specified
value.

6-6

2-7. ADJUSTING PARTS LOCA TION DIAGRAM

MA-335 BOARD (CONDUCTOR SIDE)

CJ570

LINE IN/OUT

CN261

4

1

80

41

40

65

64

Adj

Video System

IC201

24

25

RF SW POS

1

AF SW POS

3
1

CN341

AF SW POS

1
4

IC601

SW12V

RV731

Q605

MTR12V

Q603

E

SW5V

E

JS161

RF SW POS
AF SW POS

SEPARATION

6-8E

SECTION 7

21

23

24

22

1

2

3

12

4

15

14

5

6

7

7

8

9

10

11

13

15

15

15

15

15

16

not supplied

not supplied

not supplied

*

When peeling off the antenna (large) shield plate,
be sure to apply it to the original position on the
AJ-2 board.
If not so, the resonance level of AN-17 board
becomes small.

*

Antenna (large) shield plate

(not supplied)

REP AIR PARTS LIST

7-1. EXPLODED VIEWS

NOTE:

• -XX, -X mean standardized parts, so they may
have some differences from the original one.

• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.

7-1-1. FRONT PANEL ASSEMBLY AND UPPER CASE SECTION

• The mechanical parts with no reference number
in the exploded views are not supplied.

• Hardware (#mark) list is given in the last of
this parts list.

SLV-M10HF

The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.

Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

1 3-979-310-01 RING (AV), JOG
2 3-979-309-01 BUTTON (AV), CENTER
3 X-3948-110-1 PANEL ASSY, FRONT

* 4 A-6791-566-A AJ-2A COMPL BOARD, COMPLETE

5 3-953-432-01 SPRING (GE), FL

6 3-979-302-51 DOOR (AV), CASSETTE
7 3-710-901-11 SCREW, TAPPING

8 3-979-313-01 CASE, UPPER
! 9 1-783-605-11 CORD, POWER
* 10 A-6791-567-A DM-81A BOARD, COMPLETE

11 1-762-844-21 SWITCH, ROTARY

* 12 A-6791-569-A AN-17A BOARD, COMPLETE
* 13 A-6791-568-A FR-139A BOARD, COMPLETE

14 1-783-546-11 CABLE, FLAT (FFM-24)
15 4-921-277-41 SCREW (B2.6X8), TAPPING, BIND

16 1-783-547-11 CABLE, FLAT (FFM-25)
21 1-475-749-11 COMMANDER, STANDARD (RMT-V249)
22 3-709-044-01 COVER, BATTERY
23 3-973-077-31 RING, CHANGE SPEED
24 3-972-850-01 BUTTON, FUNCTION

7-1

7-1-2. CHASSIS SECTION

57

59

not
supplied

58

*

AN holder

(not supplied)

*

Antenna (small)
shield plate
(not supplied)

52

57

57

Q102

51

53

#1

#2

56

51

#1

#1

Q101

53

57

not supplied

57

54

57

55

not supplied

*

When peeling off the antenna (small) shield plate,
be sure to apply it to the original position on the
AN holder.
If not so, the resonance level of AN-16 board
becomes small.

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

51 3-979-314-01 BASE (R), MD

* 52 A-6791-570-A MA-335A COMPL BOARD, COMPLETE
* 53 3-960-273-01 SPACER, TOP END

! 54 1-468-308-11 POWER BLOCK SR821

* 55 3-979-564-21 PANEL, REAR

56 1-779-725-11 CONNECTOR, BOARD TO BOARD 5P
57 3-970-608-21 SUMITITE (B3), +BV

* 58 A-6791-571-A AN-16A BOARD, COMPLETE
* 59 A-6791-572-A NL-2A BOARD, COMPLETE

Q101 8-729-043-84 TRANSISTOR PT380F3

Q102 8-729-043-84 TRANSISTOR PT380F3

7-2

Note :

The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.

Note :

Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.

7-1-3. MECHANISM DECK-1

707

708

706

705

704

703

723

722

709

#701

710

not
supplied

712

711

702

701

713

720

701

721

719

716

714

715

717

718

#701

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

701 3-977-509-01 WASHER, THRUST
702 3-977-507-01 TABLE, REEL (S) (GRAY)
703 3-977-508-01 TABLE, REEL (T) (BLACK)
704 1-500-144-11 HEAD, FE
705 3-977-495-01 SHAFT TG2

724

713 3-977-447-01 GEAR, ELEVATOR
714 3-977-514-01 OPENER, LID
715 3-977-441-01 GEAR, PINCH PRESSING
716 3-977-445-01 GEAR, TG8 ARM DRIVING
717 3-977-465-01 SPRING,EXTENSION(RVS BRAKE)

706 3-977-494-01 HOLDER, FEH
707 A-6759-619-C FL COMPLETE ASSY
708 3-977-535-01 PLATE, LUMINOUS(END SENSOR)
709 3-977-536-01 PLATE, LUMINOUS(TOP SENSOR)
710 3-970-471-01 SPRING (DECK OPEN), TORSION

711 A-6759-615-A PRESS BLOCK ASSY, PINCH
712 3-958-455-01 SPRING (PINCH), TENSION

718 X-3947-582-1 ARM ASSY, RVS BRAKE
719 3-977-446-01 GEAR, TG8 ARM
720 X-3947-590-1 TG8 ASSY
721 A-6759-620-A HEAD BLOCK ASSY, ACE (TDK)
722 3-974-556-01 + HEXA TT 2.6X9 (TAPER)

723 3-979-508-01 SCREW
724 3-978-485-01 PLATE, GUIDE CASSETTE

7-3

7-1-4. MECHANISM DECK-2

#701

767

771

776

772

773

753

756

755

754

760

758
759

757

752

761

766

763

774

764

762

#701

762

763

#702

775

765

751

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

751 X-3947-581-1 BRAKE ASSY,MAIN(T)
752 3-977-462-01 SPRING,EXTENTION. (MAIN BRAKE)
753 X-3947-573-1 ARM ASSY, PENDULUM
754 X-3947-580-2 BRAKE ASSY, MAIN(S)
755 3-977-513-02 LEVER, REC. PROOF

756 3-976-767-01 SPRING, TENS. (REC. PROOF)
757 3-977-487-01 BOSS, TG1 FULCRUM
758 X-3947-587-1 TG1 ASSY
759 X-3947-589-1 BAND ASSY, TG1
760 3-977-488-01 SPRING (POWER TENSION)

761 A-6750-324-A SHUTTLE (S) BLOCK ASSY
762 X-3944-378-1 ROLLER ASSY, GUIDE

763 3-965-178-01 SPRING
764 3-969-632-04 BASE, DRUM
765 A-6750-325-A SHUTTLE (T) BLOCK ASSY
766 3-977-501-01 PLATE, LUMINOUS
767 X-3943-899-8 GROUND ASSY, SHAFT

771 A-6746-074-G ROLLER BLOCK ASSY, HC
772 X-3947-255-1 ROLLER ASSY, HC
773 3-975-724-07 ARM, HC
774 X-3946-855-1 SHUTTLE (S) ASSY
775 X-3946-856-1 SHUTTLE (T) ASSY

776 8-839-044-02 DRUM ASSY DZH-94A/Z-RP (M901)

7-4

7-1-5. MECHANISM DECK-3

816

815

817

#701

804

812

809

805

811

810

808

806

803
814

807

M902

813

828

827

826

829

803

818

819
820
821

822
823

824

830

M903

803
802

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

801 3-977-437-01 RETAINER,CAM MOTOR
802 X-3947-584-1 ASSY, REEL DIRECT
803 3-977-443-01 WASHER, STOPPER
804 3-977-438-01 WORM - WHEEL
805 3-977-506-01 ARM, LIMITTER SELECTION

806 3-977-444-01 GEAR, PINCH TRANSMISSION
807 3-977-515-01 GUIDE, FL SLIDER
808 3-977-517-01 PLATE, SLIDE, FL
809 3-977-519-01 SPRING, TENS. (LIMIT, FL)
810 3-977-518-02 PLATE, LIMITTER, FL

811 3-977-516-01 HOLDER, FL SLIDER
812 3-977-877-01 PLATE, RETAINER
813 3-977-504-01 GEAR, CLUTCH
814 X-3947-585-1 GEAR ASSY, PULLEY
815 3-977-510-01 BELT, RUBBER

801

825

#703

817 3-977-439-01 GEAR, CAM
818 3-977-442-01 SLIDER
819 3-977-455-01 GEAR, LOADING(T)
820 3-977-456-03 SPRING, TORSION (LOAD T)
821 X-3947-579-1 LEVER ASSY, LOADING(T)

822 3-977-451-01 GEAR, LOADING(S)
823 3-977-452-01 SPRING, TORSION (LOAD S)
824 X-3947-578-1 LEVER ASSY, LOADING(S)
825 X-3947-576-2 CHASSIS ASSY, MECHANICAL
826 3-977-468-01 SHAFT, CAPSTAN BRAKE

827 3-977-467-02 SPRING, CAP BRAKE
828 X-3947-583-1 BRAKE ASSY, CAPSTAN
829 3-977-489-01 ARM, TG1 DRIVING
830 A-6759-616-A GEAR BLOCK ASSY, LOADING
M902 1-698-971-11 MOTOR, DC

816 3-977-440-01 WASHER, STOPPER

M903 X-3947-577-1 MOTOR ASSY, CAM

7-5

AJ-2 AN-16

AN-17 DM-81 FR-139

7-2. ELECTRICAL PARTS LIST

NOTE:

When indicating parts by reference number,
please include the board name.

The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.

Les composants identifiés par une marque
! sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

* A-6791-566-A AJ-2A BOARD, COMPLETE

*********************

< CAPACITOR >

C806 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

< PIN JACK >

CJ801 1-774-509-11 JACK, PIN 3P (LINE-2 IN)

< CONNECTOR >

• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.

• -XX, -X mean standardized parts, so they may
have some difference from the original one.

• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.

• CAPA CITORS:
uF: µF

(Ref.No.: 3,000 Series)

CN101 1-506-482-11 PIN, CONNECTOR 3P

************************************************************

* A-6791-567-A DM-81A BOARD, COMPLETE

CN440 1-770-031-11 CONNECTOR, BOARD TO BOARD 7P
CN441 1-770-514-41 CONNECTOR, FFC/FPC 5P

• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable

• COILS
uH: µH

• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...

< CONNECTOR >

**********************

(Ref.No.: 2,000 Series)

< CONNECTOR >

CN801 1-506-484-11 PIN, CONNECTOR 5P

< DIODE >

D801 8-719-421-59 DIODE MA3075WA-(TX)
D802 8-719-421-59 DIODE MA3075WA-(TX)
D803 8-719-422-37 DIODE MA8051
D804 8-719-421-59 DIODE MA3075WA-(TX)

< RESISTOR >

R801 1-216-295-00 METAL CHIP 0 5% 1/10W
R802 1-216-295-00 METAL CHIP 0 5% 1/10W
R803 1-216-022-00 METAL CHIP 75 5% 1/10W

************************************************************

* A-6791-571-A AN-16A BOARD, COMPLETE

**********************

(Ref.No.: 3,000 Series)

< CAPACITOR >

C201 1-163-136-00 CERAMIC CHIP 620PF 1% 50V

< CONNECTOR >

CN201 1-506-468-11 PIN, CONNECTOR 3P

< RESISTOR >

< DIODE >

D440 8-719-056-06 DIODE SLR-342DCT31

< TRANSISTOR >

Q440 8-729-424-08 TRANSISTOR UN2111

< RESISTOR >

R441 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R442 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R443 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R444 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R445 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

R446 1-216-029-00 METAL CHIP 150 5% 1/10W

< SWITCH >

S441 1-762-196-21 SWITCH, TACT (EJECT)
S442 1-762-196-21 SWITCH, TACT (REC)
S443 1-762-196-21 SWITCH, TACT (JOG)
S444 1-762-196-21 SWITCH, TACT (PAUSE)

************************************************************

* A-6791-568-A FR-139A BOARD, COMPLETE

***********************

(Ref.No.: 2,000 Series)

R201 1-216-295-00 METAL CHIP 0 5% 1/10W
R202 1-216-295-00 METAL CHIP 0 5% 1/10W

************************************************************

* A-6791-569-A AN-17A BOARD, COMPLETE

**********************

(Ref.No.: 3,000 Series)

< CAPACITOR >

C101 1-125-830-11 CERAMIC CHIP 680PF 1% 50V
C102 1-163-243-11 CERAMIC CHIP 47PF 5% 50V

< BUZZER >

BZ460 1-529-104-11 BUZZER, PIEZOELECTRIC

< CAPACITOR >

C460 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V
C461 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C462 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C463 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C464 1-164-232-11 CERAMIC CHIP 0.01uF 50V

7-6

FR-139

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

C465 1-126-916-11 ELECT 1000uF 20% 6.3V
C466 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C467 1-126-935-11 ELECT 470uF 20% 6.3V
C468 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C469 1-104-905-11 CAPACITOR 0.22F 5.5V

C471 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C472 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C473 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C474 1-163-102-00 CERAMIC CHIP 24PF 5% 50V
C475 1-164-232-11 CERAMIC CHIP 0.01uF 50V

C476 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C477 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C478 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C479 1-126-096-11 ELECT 10uF 20% 35V

< CONNECTOR >

CN460 1-695-392-31 PIN, CONNECTOR (PC BOARD) 31P

* CN461 1-691-406-11 CONNECTOR, BOARD TO BOARD 7P

CN464 1-695-368-31 PIN, CONNECTOR (PC BOARD) 7P

< DIODE >

D420 8-719-110-03 DIODE RD7.5ES-B2
D460 8-719-056-07 DIODE SLR-342MCT31
D462 8-719-200-82 DIODE 11ES2
D463 8-719-200-82 DIODE 11ES2
D464 8-719-056-06 DIODE SLR-342DCT31

< IC >

IC460 8-752-891-11 IC CXP82960-054Q
IC462 8-759-432-34 IC ST24W16FM6TR
IC462 8-759-454-79 IC 24LC16BT/SN
IC463 8-759-248-87 IC MM1256XF-BE
IC464 8-742-012-11 HYB IC SBX1976-51

< JUMPER RESISTOR >

JR401 1-216-296-00 METAL CHIP 0 5% 1/8W
JR402 1-216-295-00 METAL CHIP 0 5% 1/10W
JR404 1-216-295-00 METAL CHIP 0 5% 1/10W
JR405 1-216-296-00 METAL CHIP 0 5% 1/8W
JR406 1-216-295-00 METAL CHIP 0 5% 1/10W

JR407 1-216-295-00 METAL CHIP 0 5% 1/10W
JR408 1-216-296-00 METAL CHIP 0 5% 1/8W
JR409 1-216-296-00 METAL CHIP 0 5% 1/8W
JR410 1-216-296-00 METAL CHIP 0 5% 1/8W
JR411 1-216-296-00 METAL CHIP 0 5% 1/8W

JR412 1-216-296-00 METAL CHIP 0 5% 1/8W
JR413 1-216-296-00 METAL CHIP 0 5% 1/8W
JR414 1-216-295-00 METAL CHIP 0 5% 1/10W
JR415 1-216-295-00 METAL CHIP 0 5% 1/10W

R404 1-216-089-00 METAL CHIP 47K 5% 1/10W
R405 1-216-075-00 METAL CHIP 12K 5% 1/10W
R406 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R407 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R408 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

R409 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R410 1-216-075-00 METAL CHIP 12K 5% 1/10W
R411 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R412 1-216-073-00 METAL CHIP 10K 5% 1/10W
R413 1-216-073-00 METAL CHIP 10K 5% 1/10W

R415 1-216-073-00 METAL CHIP 10K 5% 1/10W
R416 1-216-073-00 METAL CHIP 10K 5% 1/10W
R417 1-216-073-00 METAL CHIP 10K 5% 1/10W
R420 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R460 1-216-029-00 METAL CHIP 150 5% 1/10W

R461 1-216-089-00 METAL CHIP 47K 5% 1/10W
R462 1-216-049-00 METAL CHIP 1K 5% 1/10W
R463 1-216-089-00 METAL CHIP 47K 5% 1/10W
R464 1-216-295-00 METAL CHIP 0 5% 1/10W
R465 1-216-295-00 METAL CHIP 0 5% 1/10W

R466 1-216-073-00 METAL CHIP 10K 5% 1/10W
R467 1-216-073-00 METAL CHIP 10K 5% 1/10W
R468 1-216-113-00 METAL CHIP 470K 5% 1/10W
R469 1-216-073-00 METAL CHIP 10K 5% 1/10W
R470 1-216-073-00 METAL CHIP 10K 5% 1/10W

R471 1-216-025-91 RES,CHIP 100 5% 1/10W
R472 1-216-025-91 RES,CHIP 100 5% 1/10W
R474 1-216-113-00 METAL CHIP 470K 5% 1/10W
R475 1-216-295-00 METAL CHIP 0 5% 1/10W
R476 1-216-295-00 METAL CHIP 0 5% 1/10W

R477 1-216-095-00 METAL CHIP 82K 5% 1/10W
R478 1-216-113-00 METAL CHIP 470K 5% 1/10W
R479 1-216-049-00 METAL CHIP 1K 5% 1/10W
R480 1-216-049-00 METAL CHIP 1K 5% 1/10W
R481 1-216-049-00 METAL CHIP 1K 5% 1/10W

R482 1-216-049-00 METAL CHIP 1K 5% 1/10W
R483 1-216-073-00 METAL CHIP 10K 5% 1/10W
R484 1-216-073-00 METAL CHIP 10K 5% 1/10W
R485 1-216-113-00 METAL CHIP 470K 5% 1/10W
R486 1-216-081-00 METAL CHIP 22K 5% 1/10W

R487 1-216-029-00 METAL CHIP 150 5% 1/10W
R488 1-216-025-91 RES,CHIP 100 5% 1/10W
R490 1-216-025-91 RES,CHIP 100 5% 1/10W
R492 1-216-295-00 METAL CHIP 0 5% 1/10W
R493 1-216-295-00 METAL CHIP 0 5% 1/10W

< RESISTOR >

< SWITCH >

< COIL >

L181 1-410-509-11 INDUCTOR 10uH

< FLUORESCENT INDICATOR >

ND420 1-517-733-11 TUBE, FLUORESCENT INDICATION

< TRANSISTOR >

Q460 8-729-421-22 TRANSISTOR UN2211
Q461 8-729-421-22 TRANSISTOR UN2211

S402 1-762-196-21 SWITCH, TACT (POWER)
S403 1-762-196-21 SWITCH, TACT (COMMAND MODE)
S404 1-762-196-21 SWITCH, TACT (SMARTFILE)
S405 1-762-196-21 SWITCH, TACT (EASY SET UP)
S406 1-762-196-21 SWITCH, TACT (CURSOR)

S407 1-762-196-21 SWITCH, TACT (OK)
S408 1-762-196-21 SWITCH, TACT (INPUT SELECT)
S409 1-762-196-21 SWITCH, TACT (CHANNEL: -)
S410 1-762-196-21 SWITCH, TACT (CHANNEL: +)
S411 1-762-196-21 SWITCH, TACT (REW)

S412 1-762-196-21 SWITCH, TACT (FF)

7-7

FR-139

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

X460 1-760-494-11 VIBRATOR, CRYSTAL 16MHz
X461 1-579-463-11 VIBRATOR, CRYSTAL 32.768kHz

************************************************************

MA-335

< VIBRATOR >

C219 1-164-159-21 CERAMIC 0.1uF 50V
C220 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C222 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C223 1-124-589-11 ELECT 47uF 20% 16V
C226 1-163-038-00 CERAMIC CHIP 0.1uF 25V

* A-6791-570-A MA-335A BOARD, COMPLETE

***********************

(Ref.No.: 1,000 Series)

* 3-960-273-01 SPACER, TOP END
* 3-960-274-01 SPACER, LED

< CAPACITOR >

C101 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C102 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C103 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C104 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C105 1-128-057-11 ELECT 330uF 20% 6.3V

C106 1-124-589-11 ELECT 47uF 20% 16V
C108 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C109 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C118 1-137-441-11 FILM 0.027uF 5% 50V
C119 1-126-157-11 ELECT 10uF 20% 16V

C120 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C121 1-124-463-00 ELECT 0.1uF 20% 50V
C122 1-126-154-11 ELECT 47uF 20% 6.3V
C123 1-130-489-00 MYLAR 0.033uF 5% 50V
C140 1-126-933-11 ELECT 100uF 20% 16V

C142 1-126-933-11 ELECT 100uF 20% 16V
C143 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C144 1-163-018-00 CERAMIC CHIP 0.0056uF 5% 50V
C145 1-126-967-11 ELECT 47uF 20% 16V
C146 1-163-263-11 CERAMIC CHIP 330PF 5% 50V

C147 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C149 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C150 1-126-967-11 ELECT 47uF 20% 16V
C151 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
C152 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V

C153 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C160 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C161 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C162 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C163 1-126-154-11 ELECT 47uF 20% 6.3V

C164 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C165 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C166 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C172 1-124-584-00 ELECT 100uF 20% 10V
C201 1-109-982-11 CERAMIC CHIP 1uF 10% 10V

C202 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V
C204 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C205 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C206 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C207 1-164-232-11 CERAMIC CHIP 0.01uF 50V

C208 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
C209 1-124-248-00 ELECT 22uF 20% 35V
C210 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C214 1-163-124-00 CERAMIC CHIP 200PF 5% 50V
C217 1-109-982-11 CERAMIC CHIP 1uF 10% 10V

C228 1-124-261-00 ELECT 10uF 20% 50V
C229 1-164-159-21 CERAMIC 0.1uF 50V
C230 1-124-589-11 ELECT 47uF 20% 16V
C231 1-124-261-00 ELECT 10uF 20% 50V
C232 1-109-982-11 CERAMIC CHIP 1uF 10% 10V

C233 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C234 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C235 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C236 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C237 1-164-232-11 CERAMIC CHIP 0.01uF 50V

C238 1-164-159-21 CERAMIC 0.1uF 50V
C240 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C241 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C242 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C243 1-164-232-11 CERAMIC CHIP 0.01uF 50V

C245 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V
C246 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C247 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V
C248 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C250 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C251 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C252 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C253 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C254 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C255 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C256 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C257 1-163-241-11 CERAMIC CHIP 39PF 5% 50V
C260 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C261 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C264 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V

C265 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C266 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C267 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C268 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C269 1-163-235-11 CERAMIC CHIP 22PF 5% 50V

C270 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C271 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C272 1-163-099-00 CERAMIC CHIP 18PF 5% 50V
C273 1-163-099-00 CERAMIC CHIP 18PF 5% 50V
C274 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V

C276 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C277 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C278 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C279 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C280 1-124-584-00 ELECT 100uF 20% 10V

C281 1-164-346-11 CERAMIC CHIP 1uF 16V
C282 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C283 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C284 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C285 1-162-306-11 CERAMIC 0.01uF 30% 16V

C286 1-124-584-00 ELECT 100uF 20% 10V
C287 1-163-227-11 CERAMIC CHIP 10PF 0.5PF 50V
C288 1-163-227-11 CERAMIC CHIP 10PF 0.5PF 50V
C289 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C301 1-164-159-21 CERAMIC 0.1uF 50V

7-8

MA-335

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

C305 1-126-160-11 ELECT 1uF 20% 50V
C306 1-126-160-11 ELECT 1uF 20% 50V
C307 1-126-964-11 ELECT 10uF 20% 50V
C308 1-126-967-11 ELECT 47uF 20% 16V
C309 1-126-963-11 ELECT 4.7uF 20% 50V

C509 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C511 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C512 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C513 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C514 1-163-237-11 CERAMIC CHIP 27PF 5% 50V

C310 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C311 1-163-014-00 CERAMIC CHIP 0.0027uF 10% 50V
C312 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C313 1-124-261-00 ELECT 10uF 20% 50V
C314 1-164-232-11 CERAMIC CHIP 0.01uF 50V

C315 1-126-160-11 ELECT 1uF 20% 50V
C317 1-126-163-11 ELECT 4.7uF 20% 50V
C318 1-126-967-11 ELECT 47uF 20% 16V
C331 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C332 1-164-232-11 CERAMIC CHIP 0.01uF 50V

C333 1-124-589-11 ELECT 47uF 20% 16V
C334 1-137-374-11 FILM 0.047uF 5% 50V
C340 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C341 1-124-589-11 ELECT 47uF 20% 16V
C342 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V

C346 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C350 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C352 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C353 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C357 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

C358 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C359 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C361 1-164-222-11 CERAMIC CHIP 0.22uF 25V
C362 1-164-222-11 CERAMIC CHIP 0.22uF 25V
C363 1-126-960-11 ELECT 1uF 20% 50V

C515 1-124-589-11 ELECT 47uF 20% 16V
C516 1-126-160-11 ELECT 1uF 20% 50V
C517 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C518 1-124-257-00 ELECT 2.2uF 20% 50V
C519 1-163-139-00 CERAMIC CHIP 820PF 5% 50V

C520 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C521 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C522 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C523 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C560 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

C561 1-126-935-11 ELECT 470uF 20% 6.3V
C563 1-124-589-11 ELECT 47uF 20% 16V
C564 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C621 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C622 1-126-965-11 ELECT 22uF 20% 50V

C623 1-124-589-11 ELECT 47uF 20% 16V
C624 1-124-589-11 ELECT 47uF 20% 16V
C625 1-126-967-11 ELECT 47uF 20% 16V
C626 1-128-131-11 ELECT 22uF 20% 50V
C627 1-128-131-11 ELECT 22uF 20% 50V

C628 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C629 1-126-966-11 ELECT 33uF 20% 16V
C701 1-126-967-11 ELECT 47uF 20% 16V
C704 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C706 1-126-963-11 ELECT 4.7uF 20% 50V

C364 1-126-960-11 ELECT 1uF 20% 50V
C365 1-126-960-11 ELECT 1uF 20% 50V
C366 1-126-960-11 ELECT 1uF 20% 50V
C369 1-126-964-11 ELECT 10uF 20% 50V
C370 1-126-964-11 ELECT 10uF 20% 50V

C371 1-126-964-11 ELECT 10uF 20% 50V
C372 1-126-964-11 ELECT 10uF 20% 50V
C373 1-126-964-11 ELECT 10uF 20% 50V
C374 1-126-960-11 ELECT 1uF 20% 50V
C375 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V

C377 1-126-967-11 ELECT 47uF 20% 16V
C378 1-126-964-11 ELECT 10uF 20% 50V
C379 1-126-961-11 ELECT 2.2uF 20% 50V
C380 1-126-964-11 ELECT 10uF 20% 50V
C381 1-126-967-11 ELECT 47uF 20% 16V

C383 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C384 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C385 1-126-967-11 ELECT 47uF 20% 16V
C386 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C391 1-164-232-11 CERAMIC CHIP 0.01uF 50V

C398 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V
C399 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V
C501 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V
C502 1-124-589-11 ELECT 47uF 20% 16V
C503 1-164-232-11 CERAMIC CHIP 0.01uF 50V

C707 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C709 1-126-933-11 ELECT 100uF 20% 16V
C710 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C712 1-126-933-11 ELECT 100uF 20% 16V
C735 1-126-964-11 ELECT 10uF 20% 50V

C736 1-126-967-11 ELECT 47uF 20% 16V
C801 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
C802 1-163-263-11 CERAMIC CHIP 330PF 5% 50V
C803 1-163-243-11 CERAMIC CHIP 47PF 5% 50V
C804 1-163-091-00 CERAMIC CHIP 8PF 50V

C805 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C806 1-163-087-00 CERAMIC CHIP 4PF 50V
C807 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C808 1-163-127-00 CERAMIC CHIP 270PF 5% 50V
C809 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V

C810 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C811 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C812 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
C813 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C814 1-163-257-11 CERAMIC CHIP 180PF 5% 50V

C815 1-124-589-11 ELECT 47uF 20% 16V
C816 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C817 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C851 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C852 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C504 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C505 1-126-157-11 ELECT 10uF 20% 16V
C506 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C507 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C508 1-163-237-11 CERAMIC CHIP 27PF 5% 50V

C853 1-163-243-11 CERAMIC CHIP 47PF 5% 50V
C854 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C855 1-163-243-11 CERAMIC CHIP 47PF 5% 50V
C859 1-124-589-11 ELECT 47uF 20% 16V
C871 1-124-589-11 ELECT 47uF 20% 16V

7-9

MA-335

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

C872 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V
C873 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C874 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C875 1-164-346-11 CERAMIC CHIP 1uF 16V
C876 1-163-135-00 CERAMIC CHIP 560PF 5% 50V

C878 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C880 1-163-099-00 CERAMIC CHIP 18PF 5% 50V
C881 1-163-099-00 CERAMIC CHIP 18PF 5% 50V
C980 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C981 1-126-967-11 ELECT 47uF 20% 16V

C982 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C983 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C984 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C985 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C986 1-163-038-00 CERAMIC CHIP 0.1uF 25V

< PIN JACK >

CJ570 1-779-011-11 JACK, PIN 6P (LINE-1 IN/LINE OUT)

< CONNECTOR >

CN101 1-779-724-11 CONNECTOR, BOARD TO BOARD 5P
CN102 1-779-723-11 CONNECTOR, BOARD TO BOARD 9P

* CN103 1-766-716-11 CONNECTOR, BOARD TO BOARD 3P

CN162 1-568-845-11 PIN, CONNECTOR (PC BOARD) 31P
CN163 1-506-469-11 PIN, CONNECTOR 4P

CN165 1-506-470-11 PIN, CONNECTOR 5P
CN260 1-766-986-11 CONNECTOR, FFC/FPC 13P

* CN261 1-560-892-00 PIN, CONNECTOR 4P

CN301 1-506-471-11 PIN, CONNECTOR 6P
CN302 1-506-468-11 PIN, CONNECTOR 3P

* CN341 1-560-891-00 PIN, CONNECTOR 3P

CN423 1-506-470-11 PIN, CONNECTOR 5P
CN603 1-569-337-11 CONNECTOR, BOARD TO BOARD 11P

D983 8-719-110-08 DIODE RD8.2ES-B2
D984 8-719-110-08 DIODE RD8.2ES-B2

< IC >

IC100 8-759-702-02 IC NJM062M
IC101 8-759-481-46 IC LB1943
IC140 8-759-100-93 IC uPC393G2
IC141 8-759-438-83 IC BA6305F-E2
IC161 8-752-896-78 IC CXP87852-046Q

IC201 8-759-488-74 IC LA71534M-MPB
IC202 8-759-439-51 IC LC89978M-TE-L
IC260 8-759-352-17 IC HA118195NT
IC301 8-759-499-30 IC BA7755AF-E2
IC340 8-759-486-92 IC LA7256

IC360 8-759-486-64 IC TDA9615H/N1,557
IC500 8-759-529-44 IC MB90089PF-G-209-BND-ER
IC501 8-759-164-09 IC LA7218M-TE-R
IC601 8-759-438-18 IC PQ12RD08
IC733 8-742-037-00 HY B IC SBX1837-51

IC871 8-759-430-84 IC MC68HC05CCVFB-LSC86145FB
IC980 8-759-356-27 IC NJM2129M-TE2

< JUMPER RESISTOR >

JR001 1-216-295-00 METAL CHIP 0 5% 1/10W
JR002 1-216-296-00 METAL CHIP 0 5% 1/8W
JR004 1-216-295-00 METAL CHIP 0 5% 1/10W
JR005 1-216-296-00 METAL CHIP 0 5% 1/8W
JR007 1-216-296-00 METAL CHIP 0 5% 1/8W

JR008 1-216-296-00 METAL CHIP 0 5% 1/8W
JR009 1-216-296-00 METAL CHIP 0 5% 1/8W
JR010 1-216-296-00 METAL CHIP 0 5% 1/8W
JR011 1-216-296-00 METAL CHIP 0 5% 1/8W
JR012 1-216-296-00 METAL CHIP 0 5% 1/8W

< JACK >

CNJ980 1-779-013-11 JACK, MINIATURE (CONTROL S IN)
CNJ981 1-784-598-11 JACK (CONTROL S OUT)

< DIODE >

D103 8-719-048-26 DIODE GL528V1
D107 8-719-911-19 DIODE 1SS119
D109 8-719-200-82 DIODE 11ES2
D161 8-719-200-82 DIODE 11ES2
D370 8-719-110-08 DIODE RD8.2ES-B2

D379 8-719-911-19 DIODE 1SS119
D502 8-719-911-19 DIODE 1SS119
D503 8-719-911-19 DIODE 1SS119
D504 8-719-911-19 DIODE 1SS119
D560 8-719-109-74 DIODE RD4.3ES-B1

D561 8-719-109-74 DIODE RD4.3ES-B1
D611 8-719-911-19 DIODE 1SS119
D612 8-719-109-85 DIODE RD5.1ES-B2
D614 8-719-911-19 DIODE 1SS119
D702 8-719-150-92 DIODE RD33ES-T1B

D801 8-719-971-05 DIODE HSM123
D802 8-719-911-19 DIODE 1SS119
D980 8-719-110-08 DIODE RD8.2ES-B2
D981 8-719-110-08 DIODE RD8.2ES-B2
D982 8-719-911-19 DIODE 1SS119

JR013 1-216-295-00 METAL CHIP 0 5% 1/10W
JR014 1-216-296-00 METAL CHIP 0 5% 1/8W
JR015 1-216-296-00 METAL CHIP 0 5% 1/8W
JR016 1-216-295-00 METAL CHIP 0 5% 1/10W
JR017 1-216-296-00 METAL CHIP 0 5% 1/8W

JR018 1-216-296-00 METAL CHIP 0 5% 1/8W
JR019 1-216-295-00 METAL CHIP 0 5% 1/10W
JR020 1-216-296-00 METAL CHIP 0 5% 1/8W
JR021 1-216-295-00 METAL CHIP 0 5% 1/10W
JR022 1-216-296-00 METAL CHIP 0 5% 1/8W

JR023 1-216-296-00 METAL CHIP 0 5% 1/8W
JR024 1-216-296-00 METAL CHIP 0 5% 1/8W
JR025 1-216-295-00 METAL CHIP 0 5% 1/10W
JR026 1-216-295-00 METAL CHIP 0 5% 1/10W
JR027 1-216-295-00 METAL CHIP 0 5% 1/10W

JR028 1-216-295-00 METAL CHIP 0 5% 1/10W
JR029 1-216-295-00 METAL CHIP 0 5% 1/10W
JR030 1-216-296-00 METAL CHIP 0 5% 1/8W
JR031 1-216-296-00 METAL CHIP 0 5% 1/8W
JR032 1-216-296-00 METAL CHIP 0 5% 1/8W

JR033 1-216-295-00 METAL CHIP 0 5% 1/10W
JR034 1-216-296-00 METAL CHIP 0 5% 1/8W
JR035 1-216-295-00 METAL CHIP 0 5% 1/10W
JR036 1-216-296-00 METAL CHIP 0 5% 1/8W
JR037 1-216-296-00 METAL CHIP 0 5% 1/8W

7-10

MA-335

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

JR038 1-216-295-00 METAL CHIP 0 5% 1/10W
JR039 1-216-296-00 METAL CHIP 0 5% 1/8W
JR040 1-216-296-00 METAL CHIP 0 5% 1/8W
JR041 1-216-296-00 METAL CHIP 0 5% 1/8W
JR043 1-216-296-00 METAL CHIP 0 5% 1/8W

JR044 1-216-296-00 METAL CHIP 0 5% 1/8W
JR045 1-216-296-00 METAL CHIP 0 5% 1/8W
JR046 1-216-295-00 METAL CHIP 0 5% 1/10W
JR047 1-216-296-00 METAL CHIP 0 5% 1/8W
JR048 1-216-296-00 METAL CHIP 0 5% 1/8W

JR049 1-216-296-00 METAL CHIP 0 5% 1/8W
JR050 1-216-295-00 METAL CHIP 0 5% 1/10W

< JUMPER RESISTOR >

JS609 1-216-295-00 METAL CHIP 0 5% 1/10W

< COIL >

L101 1-414-936-21 INDUCTOR 22uH
L140 1-414-189-31 INDUCTOR 100uH
L141 1-414-189-31 INDUCTOR 100uH
L160 1-414-934-21 INDUCTOR 10uH
L201 1-408-405-00 INDUCTOR 4.7uH

L204 1-414-940-21 INDUCTOR 100uH
L207 1-414-931-21 INDUCTOR 3.3uH
L262 1-414-940-21 INDUCTOR 100uH
L263 1-414-940-21 INDUCTOR 100uH
L331 1-414-940-21 INDUCTOR 100uH

L341 1-414-940-21 INDUCTOR 100uH
L501 1-414-936-21 INDUCTOR 22uH
L502 1-414-940-21 INDUCTOR 100uH
L503 1-414-940-21 INDUCTOR 100uH
L560 1-414-940-21 INDUCTOR 100uH

L604 1-410-519-11 INDUCTOR 68uH
L605 1-414-930-21 INDUCTOR 2.2uH
L606 1-414-934-21 INDUCTOR 10uH
L607 1-414-930-21 INDUCTOR 2.2uH
L703 1-414-930-21 INDUCTOR 2.2uH

L704 1-414-938-21 INDUCTOR 47uH
L731 1-414-938-21 INDUCTOR 47uH
L801 1-410-524-41 INDUCTOR 180uH
L803 1-414-946-21 INDUCTOR 39uH
L804 1-414-946-21 INDUCTOR 39uH

L805 1-414-939-21 INDUCTOR 68uH
L808 1-414-932-21 INDUCTOR 4.7uH
L871 1-414-934-21 INDUCTOR 10uH

< PHOTO INTERRUPTER >

PH101 8-749-013-23 PHOTO INTERRUPTER GP3S120
PH102 8-749-013-23 PHOTO INTERRUPTER GP3S120

< IC LINK >

! PS101 1-533-586-11 LINK, IC 315mA
! PS600 1-533-592-11 LINK, IC 1.6A

Q101 8-729-043-84 TRANSISTOR PT380F3
Q102 8-729-043-84 TRANSISTOR PT380F3
Q103 8-729-281-53 TRANSISTOR 2SC1815-GR
Q140 8-729-901-06 TRANSISTOR DTA144EK
Q201 8-729-230-49 TRANSISTOR 2SC2712-G

Q204 8-729-024-88 TRANSISTOR MUN2212T1
Q205 8-729-421-19 TRANSISTOR UN2213
Q208 8-729-230-49 TRANSISTOR 2SC2712-G
Q209 8-729-216-21 TRANSISTOR 2SA1162Y -TE85L
Q210 8-729-230-49 TRANSISTOR 2SC2712-G

Q211 8-729-230-49 TRANSISTOR 2SC2712-G
Q214 8-729-421-19 TRANSISTOR UN2213
Q260 8-729-230-49 TRANSISTOR 2SC2712-G
Q301 8-729-281-53 TRANSISTOR 2SC1815-GR
Q331 8-729-802-91 TRANSISTOR 2SD879

Q379 8-729-216-22 TRANSISTOR 2SA1162
Q386 8-729-230-49 TRANSISTOR 2SC2712-G
Q387 8-729-230-49 TRANSISTOR 2SC2712-G
Q502 8-729-010-05 TRANSISTOR MSB709-RT1
Q503 8-729-010-05 TRANSISTOR MSB709-RT1

Q505 8-729-010-05 TRANSISTOR MSB709-RT1
Q560 8-729-010-05 TRANSISTOR MSB709-RT1
Q603 8-729-018-99 TRANSISTOR 2SD2394-F
Q604 8-729-010-29 TRANSISTOR MSD601-RST1
Q605 8-729-140-93 TRANSISTOR 2SB733-34

Q606 8-729-119-78 TRANSISTOR 2SC2785-HFE
Q731 8-729-421-19 TRANSISTOR UN2213
Q801 8-729-216-21 TRANSISTOR 2SA1162Y -TE85L
Q802 8-729-230-49 TRANSISTOR 2SC2712-G
Q803 8-729-216-21 TRANSISTOR 2SA1162Y -TE85L

Q804 8-729-230-49 TRANSISTOR 2SC2712-G
Q805 8-729-900-51 TRANSISTOR DTA114TK
Q806 8-729-230-49 TRANSISTOR 2SC2712-G
Q807 8-729-230-49 TRANSISTOR 2SC2712-G
Q808 8-729-230-49 TRANSISTOR 2SC2712-G

Q809 8-729-900-51 TRANSISTOR DTA114TK
Q810 8-729-230-49 TRANSISTOR 2SC2712-G
Q851 8-729-230-49 TRANSISTOR 2SC2712-G
Q852 8-729-230-49 TRANSISTOR 2SC2712-G
Q853 8-729-216-21 TRANSISTOR 2SA1162Y -TE85L

Q854 8-729-216-21 TRANSISTOR 2SA1162Y -TE85L
Q855 8-729-230-49 TRANSISTOR 2SC2712-G
Q856 8-729-230-49 TRANSISTOR 2SC2712-G
Q857 8-729-216-21 TRANSISTOR 2SA1162Y -TE85L
Q871 8-729-010-05 TRANSISTOR MSB709-RT1

Q872 8-729-010-29 TRANSISTOR MSD601-RST1
Q873 8-729-010-29 TRANSISTOR MSD601-RST1
Q874 8-729-424-08 TRANSISTOR UN2111
Q875 8-729-010-29 TRANSISTOR MSD601-RST1

R101 1-249-413-11 CARBON 470 5% 1/4W F
R102 1-216-089-00 METAL CHIP 47K 5% 1/10W
R103 1-249-437-11 CARBON 47K 5% 1/4W
R104 1-216-085-00 METAL CHIP 33K 5% 1/10W
R105 1-216-085-00 METAL CHIP 33K 5% 1/10W

Note :

The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number

7-11

specified.

< TRANSISTOR >

< RESISTOR >

Note :

Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.

MA-335

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

R106 1-249-400-11 CARBON 39 5% 1/4W F
R107 1-249-400-11 CARBON 39 5% 1/4W F
R108 1-249-421-11 CARBON 2.2K 5% 1/4W F
R109 1-216-041-00 METAL CHIP 470 5% 1/10W
R110 1-216-041-00 METAL CHIP 470 5% 1/10W

R230 1-216-045-00 METAL CHIP 680 5% 1/10W
R231 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R232 1-249-420-11 CARBON 1.8K 5% 1/4W F
R234 1-216-049-00 METAL CHIP 1K 5% 1/10W
R235 1-216-295-00 METAL CHIP 0 5% 1/10W

R111 1-216-041-00 METAL CHIP 470 5% 1/10W
R118 1-216-089-00 METAL CHIP 47K 5% 1/10W
R119 1-216-077-00 METAL CHIP 15K 5% 1/10W
R124 1-249-421-11 CARBON 2.2K 5% 1/4W F
R125 1-249-421-11 CARBON 2.2K 5% 1/4W F

R126 1-247-885-00 CARBON 180K 5% 1/4W
R127 1-249-429-11 CARBON 10K 5% 1/4W
R128 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R129 1-216-073-00 METAL CHIP 10K 5% 1/10W
R130 1-216-073-00 METAL CHIP 10K 5% 1/10W

R131 1-208-806-11 RES,CHIP 10K 0.50% 1/10W
R132 1-208-806-11 RES,CHIP 10K 0.50% 1/10W
R133 1-249-436-11 CARBON 39K 5% 1/4W
R134 1-216-089-00 METAL CHIP 47K 5% 1/10W
R135 1-216-089-00 METAL CHIP 47K 5% 1/10W

R136 1-216-089-00 METAL CHIP 47K 5% 1/10W
R137 1-216-089-00 METAL CHIP 47K 5% 1/10W
R140 1-208-830-11 RES,CHIP 100K 0.50% 1/10W
R141 1-208-830-11 RES,CHIP 100K 0.50% 1/10W
R143 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

R144 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R145 1-208-830-11 RES,CHIP 100K 0.50% 1/10W
R146 1-208-830-11 RES,CHIP 100K 0.50% 1/10W
R148 1-249-414-11 CARBON 560 5% 1/4W F
R149 1-216-065-91 RES,CHIP 4.7K 5% 1/10W

R236 1-216-049-00 METAL CHIP 1K 5% 1/10W
R237 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R238 1-216-063-91 RES,CHIP 3.9K 5% 1/10W
R239 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R240 1-216-049-00 METAL CHIP 1K 5% 1/10W

R241 1-216-295-00 METAL CHIP 0 5% 1/10W
R247 1-216-041-00 METAL CHIP 470 5% 1/10W
R260 1-216-044-00 METAL CHIP 620 5% 1/10W
R261 1-216-044-00 METAL CHIP 620 5% 1/10W
R262 1-216-295-00 METAL CHIP 0 5% 1/10W

R263 1-216-295-00 METAL CHIP 0 5% 1/10W
R264 1-216-295-00 METAL CHIP 0 5% 1/10W
R265 1-216-295-00 METAL CHIP 0 5% 1/10W
R266 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R267 1-216-073-00 METAL CHIP 10K 5% 1/10W

R268 1-216-081-00 METAL CHIP 22K 5% 1/10W
R269 1-249-421-11 CARBON 2.2K 5% 1/4W F
R270 1-247-863-91 CARBON 22K 5% 1/4W
R271 1-216-049-00 METAL CHIP 1K 5% 1/10W
R272 1-216-077-00 METAL CHIP 15K 5% 1/10W

R273 1-216-077-00 METAL CHIP 15K 5% 1/10W
R274 1-216-073-00 METAL CHIP 10K 5% 1/10W
R275 1-216-073-00 METAL CHIP 10K 5% 1/10W
R276 1-216-049-00 METAL CHIP 1K 5% 1/10W
R301 1-216-093-00 METAL CHIP 68K 5% 1/10W

R150 1-216-049-00 METAL CHIP 1K 5% 1/10W
R151 1-216-037-00 METAL CHIP 330 5% 1/10W
R152 1-216-117-00 METAL CHIP 680K 5% 1/10W
R153 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R154 1-216-111-00 METAL CHIP 390K 5% 1/10W

R155 1-216-105-91 RES,CHIP 220K 5% 1/10W
R160 1-216-077-00 METAL CHIP 15K 5% 1/10W
R161 1-216-073-00 METAL CHIP 10K 5% 1/10W
R162 1-216-089-00 METAL CHIP 47K 5% 1/10W
R163 1-216-073-00 METAL CHIP 10K 5% 1/10W

R164 1-216-073-00 METAL CHIP 10K 5% 1/10W
R165 1-216-295-00 METAL CHIP 0 5% 1/10W
R166 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R167 1-216-097-91 RES,CHIP 100K 5% 1/10W
R168 1-249-417-11 CARBON 1K 5% 1/4W F

R169 1-216-073-00 METAL CHIP 10K 5% 1/10W
R170 1-216-073-00 METAL CHIP 10K 5% 1/10W
R201 1-216-041-00 METAL CHIP 470 5% 1/10W
R202 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R203 1-216-049-00 METAL CHIP 1K 5% 1/10W

R204 1-249-413-11 CARBON 470 5% 1/4W F
R210 1-216-295-00 METAL CHIP 0 5% 1/10W
R212 1-216-073-00 METAL CHIP 10K 5% 1/10W
R213 1-249-429-11 CARBON 10K 5% 1/4W
R218 1-208-798-11 RES,CHIP 4.7K 0.50% 1/10W

R302 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
R306 1-216-073-00 METAL CHIP 10K 5% 1/10W
R307 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R309 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
R310 1-216-129-00 METAL CHIP 2.2M 5% 1/10W

R311 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
R312 1-216-079-00 METAL CHIP 18K 5% 1/10W
R313 1-216-109-00 METAL CHIP 330K 5% 1/10W
R314 1-216-035-00 METAL CHIP 270 5% 1/10W
R315 1-216-067-00 METAL CHIP 5.6K 5% 1/10W

R316 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R317 1-216-079-00 METAL CHIP 18K 5% 1/10W
R318 1-216-075-00 METAL CHIP 12K 5% 1/10W
R320 1-216-047-91 RES,CHIP 820 5% 1/10W
R331 1-217-671-11 METAL CHIP 1 5% 1/10W

R332 1-216-063-91 RES,CHIP 3.9K 5% 1/10W
R333 1-249-401-11 CARBON 47 5% 1/4W F
R334 1-216-031-00 METAL CHIP 180 5% 1/10W
R341 1-216-049-00 METAL CHIP 1K 5% 1/10W
R342 1-216-049-00 METAL CHIP 1K 5% 1/10W

R344 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R346 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R347 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R348 1-216-033-00 METAL CHIP 220 5% 1/10W
R368 1-216-133-00 METAL CHIP 3.3M 5% 1/10W

R219 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R221 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R222 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
R228 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R229 1-216-055-00 METAL CHIP 1.8K 5% 1/10W

R370 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R371 1-208-820-11 RES,CHIP 39K 0.50% 1/10W
R372 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R373 1-216-033-00 METAL CHIP 220 5% 1/10W
R374 1-216-033-00 METAL CHIP 220 5% 1/10W

7-12

MA-335

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

R378 1-249-434-11 CARBON 27K 5% 1/4W
R379 1-216-049-00 METAL CHIP 1K 5% 1/10W
R380 1-216-025-91 RES,CHIP 100 5% 1/10W
R381 1-216-025-91 RES,CHIP 100 5% 1/10W
R382 1-216-295-00 METAL CHIP 0 5% 1/10W

R748 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R749 1-216-049-00 METAL CHIP 1K 5% 1/10W
R801 1-216-049-00 METAL CHIP 1K 5% 1/10W
R802 1-216-049-00 METAL CHIP 1K 5% 1/10W
R803 1-216-039-00 METAL CHIP 390 5% 1/10W

R383 1-216-295-00 METAL CHIP 0 5% 1/10W
R384 1-216-091-00 METAL CHIP 56K 5% 1/10W
R385 1-216-091-00 METAL CHIP 56K 5% 1/10W
R386 1-216-049-00 METAL CHIP 1K 5% 1/10W
R387 1-216-049-00 METAL CHIP 1K 5% 1/10W

R389 1-216-073-00 METAL CHIP 10K 5% 1/10W
R391 1-216-049-00 METAL CHIP 1K 5% 1/10W
R392 1-216-049-00 METAL CHIP 1K 5% 1/10W
R393 1-216-295-00 METAL CHIP 0 5% 1/10W
R501 1-216-295-00 METAL CHIP 0 5% 1/10W

R502 1-216-033-00 METAL CHIP 220 5% 1/10W
R505 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R506 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
R507 1-216-081-00 METAL CHIP 22K 5% 1/10W
R508 1-216-049-00 METAL CHIP 1K 5% 1/10W

R510 1-216-081-00 METAL CHIP 22K 5% 1/10W
R514 1-216-073-00 METAL CHIP 10K 5% 1/10W
R515 1-216-101-00 METAL CHIP 150K 5% 1/10W
R517 1-216-063-91 RES,CHIP 3.9K 5% 1/10W
R518 1-216-043-91 RES,CHIP 560 5% 1/10W

R519 1-216-043-91 RES,CHIP 560 5% 1/10W
R520 1-216-033-00 METAL CHIP 220 5% 1/10W
R521 1-216-073-00 METAL CHIP 10K 5% 1/10W
R522 1-216-073-00 METAL CHIP 10K 5% 1/10W
R523 1-216-073-00 METAL CHIP 10K 5% 1/10W

R804 1-216-039-00 METAL CHIP 390 5% 1/10W
R805 1-216-049-00 METAL CHIP 1K 5% 1/10W
R806 1-216-043-91 RES,CHIP 560 5% 1/10W
R807 1-216-039-00 METAL CHIP 390 5% 1/10W
R808 1-216-033-00 METAL CHIP 220 5% 1/10W

R809 1-216-077-00 METAL CHIP 15K 5% 1/10W
R810 1-216-075-00 METAL CHIP 12K 5% 1/10W
R811 1-216-033-00 METAL CHIP 220 5% 1/10W
R812 1-216-043-91 RES,CHIP 560 5% 1/10W
R813 1-216-069-00 METAL CHIP 6.8K 5% 1/10W

R814 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R815 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
R816 1-216-075-00 METAL CHIP 12K 5% 1/10W
R817 1-216-077-00 METAL CHIP 15K 5% 1/10W
R818 1-216-039-00 METAL CHIP 390 5% 1/10W

R819 1-216-045-00 METAL CHIP 680 5% 1/10W
R820 1-216-039-00 METAL CHIP 390 5% 1/10W
R821 1-216-045-00 METAL CHIP 680 5% 1/10W
R822 1-216-049-00 METAL CHIP 1K 5% 1/10W
R823 1-216-041-00 METAL CHIP 470 5% 1/10W

R824 1-216-047-91 RES,CHIP 820 5% 1/10W
R825 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R826 1-216-025-91 RES,CHIP 100 5% 1/10W
R827 1-216-045-00 METAL CHIP 680 5% 1/10W
R828 1-216-043-91 RES,CHIP 560 5% 1/10W

R560 1-216-022-00 METAL CHIP 75 5% 1/10W
R561 1-216-021-00 METAL CHIP 68 5% 1/10W
R562 1-249-407-11 CARBON 150 5% 1/4W F
R563 1-249-407-11 CARBON 150 5% 1/4W F
R565 1-216-037-00 METAL CHIP 330 5% 1/10W

R617 1-249-417-11 CARBON 1K 5% 1/4W F
R621 1-216-089-00 METAL CHIP 47K 5% 1/10W
R622 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R623 1-247-843-11 CARBON 3.3K 5% 1/4W
R624 1-216-430-11 METAL OXIDE 390 5% 1W F

R625 1-249-429-11 CARBON 10K 5% 1/4W
R626 1-249-417-11 CARBON 1K 5% 1/4W F
R627 1-247-815-91 CARBON 220 5% 1/4W
R628 1-247-815-91 CARBON 220 5% 1/4W
R701 1-216-049-00 METAL CHIP 1K 5% 1/10W

R702 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

! R705 1-212-893-00 FUSIBLE 330 5% 1/4W F

R706 1-216-113-00 METAL CHIP 470K 5% 1/10W
R709 1-216-295-00 METAL CHIP 0 5% 1/10W
R710 1-216-295-00 METAL CHIP 0 5% 1/10W

R711 1-216-295-00 METAL CHIP 0 5% 1/10W
R712 1-216-295-00 METAL CHIP 0 5% 1/10W
R731 1-216-049-00 METAL CHIP 1K 5% 1/10W
R732 1-216-049-00 METAL CHIP 1K 5% 1/10W
R733 1-249-425-11 CARBON 4.7K 5% 1/4W F

R838 1-249-410-11 CARBON 270 5% 1/4W F
R844 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R851 1-208-820-11 RES,CHIP 39K 0.50% 1/10W
R852 1-208-802-11 RES,CHIP 6.8K 0.50% 1/10W
R853 1-208-792-11 RES,CHIP 2.7K 0.50% 1/10W

R855 1-208-770-11 RES,CHIP 330 0.50% 1/10W
R856 1-208-758-11 RES,CHIP 100 0.50% 1/10W
R857 1-208-790-11 RES,CHIP 2.2K 0.50% 1/10W
R858 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
R859 1-208-800-11 RES,CHIP 5.6K 0.50% 1/10W

R860 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R861 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R862 1-208-806-11 RES,CHIP 10K 0.50% 1/10W
R864 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R865 1-216-107-00 METAL CHIP 270K 5% 1/10W

R871 1-249-429-11 CARBON 10K 5% 1/4W
R872 1-247-807-31 CARBON 100 5% 1/4W
R873 1-247-807-31 CARBON 100 5% 1/4W
R874 1-247-807-31 CARBON 100 5% 1/4W
R875 1-247-807-31 CARBON 100 5% 1/4W

R876 1-216-081-00 METAL CHIP 22K 5% 1/10W
R877 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R878 1-216-073-00 METAL CHIP 10K 5% 1/10W
R879 1-249-417-11 CARBON 1K 5% 1/4W F
R880 1-249-429-11 CARBON 10K 5% 1/4W

R735 1-216-049-00 METAL CHIP 1K 5% 1/10W
R736 1-216-295-00 METAL CHIP 0 5% 1/10W
R737 1-216-081-00 METAL CHIP 22K 5% 1/10W
R738 1-216-081-00 METAL CHIP 22K 5% 1/10W
R739 1-249-429-11 CARBON 10K 5% 1/4W

7-13

Note :

The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.

Note :

Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.

MA-335 NL-2

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

R881 1-216-043-91 RES,CHIP 560 5% 1/10W
R882 1-216-049-00 METAL CHIP 1K 5% 1/10W
R883 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R884 1-216-047-91 RES,CHIP 820 5% 1/10W
R885 1-247-807-31 CARBON 100 5% 1/4W

C029 1-124-234-00 ELECT 22uF 20% 16V
C030 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C032 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C034 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C035 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V

R886 1-216-073-00 METAL CHIP 10K 5% 1/10W
R887 1-216-081-00 METAL CHIP 22K 5% 1/10W
R888 1-216-081-00 METAL CHIP 22K 5% 1/10W
R889 1-247-807-31 CARBON 100 5% 1/4W
R890 1-216-049-00 METAL CHIP 1K 5% 1/10W

R980 1-216-049-00 METAL CHIP 1K 5% 1/10W
R981 1-216-295-00 METAL CHIP 0 5% 1/10W

< VARIABLE RESISTOR >

RV731 1-241-766-11 RES, ADJ, CERMET 47K

< SWITCH >

S101 1-762-108-11 SWITCH, PUSH (1 KEY) (REC PROOF)
S102 1-771-155-11 SWITCH, ROTARY (MECHANISM MODE)
S701 1-571-588-11 SWITCH, SLIDE (RF UNIT CH3/CH4)

< TRANSFORMER >

T331 1-431-097-11 TRANSFORMER, BIAS OSCILLATION

< TUNER >

TU700 8-598-289-00 TUNER, FSS BTF-MA401

< VIBRATOR >

X160 1-760-494-11 VIBRATOR, CRYSTAL 16MHz
X202 1-577-380-11 VIBRATOR, CRYSTAL 3.579545MHz
X500 1-577-381-11 VIBRATOR, CRYSTAL 14.31818MHz
X501 1-577-165-11 VIBLATOR, CERAMIC 503.5kHz
X871 1-577-133-21 VIBRATOR, CRYSTAL 8MHz

************************************************************

* A-6791-572-A NL-2A BOARD, COMPLETE

*********************

(Ref.No.: 3,000 Series)

< CAPACITOR >

C002 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C006 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C007 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C008 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C009 1-163-251-11 CERAMIC CHIP 100PF 5% 50V

C010 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C011 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C012 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C013 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C015 1-163-251-11 CERAMIC CHIP 100PF 5% 50V

C016 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C017 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C018 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C020 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C021 1-164-232-11 CERAMIC CHIP 0.01uF 50V

C022 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C023 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C024 1-124-234-00 ELECT 22uF 20% 16V
C026 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C027 1-124-589-11 ELECT 47uF 20% 16V

C036 1-124-234-00 ELECT 22uF 20% 16V
C037 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C038 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
C039 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
C041 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V

C045 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C046 1-124-234-00 ELECT 22uF 20% 16V
C047 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C048 1-124-234-00 ELECT 22uF 20% 16V

< CONNECTOR >

CN001 1-506-468-11 PIN, CONNECTOR 3P
CN002 1-506-468-11 PIN, CONNECTOR 3P
CN003 1-506-470-11 PIN, CONNECTOR 5P
CN004 1-695-330-31 PIN, CONNECTOR (PC BOARD) 7P

< JACK >

CNJ001 1-784-598-11 JACK (CPD IN)

< DIODE >

D001 8-719-911-19 DIODE 1SS119
D002 8-719-911-19 DIODE 1SS119
D003 8-719-911-19 DIODE 1SS119
D004 8-719-911-19 DIODE 1SS119
D005 8-719-911-19 DIODE 1SS119

D007 8-719-110-08 DIODE RD8.2ES-B2
D008 8-719-911-19 DIODE 1SS119

< INDUCTOR CHIP >

FB001 1-414-234-11 INDUCTOR CHIP 0UH
FB002 1-414-234-11 INDUCTOR CHIP 0UH
FB003 1-414-234-11 INDUCTOR CHIP 0UH
FB004 1-414-233-21 INDUCTOR CHIP 0UH
FB005 1-414-233-21 INDUCTOR CHIP 0UH

FB006 1-414-233-21 INDUCTOR CHIP 0UH
FB007 1-414-233-21 INDUCTOR CHIP 0UH
FB008 1-414-234-11 INDUCTOR CHIP 0UH
FB009 1-414-234-11 INDUCTOR CHIP 0UH
FB010 1-414-234-11 INDUCTOR CHIP 0UH

FB011 1-414-234-11 INDUCTOR CHIP 0UH
FB012 1-414-234-11 INDUCTOR CHIP 0UH
FB020 1-414-235-11 INDUCTOR CHIP 0UH
FB021 1-414-235-11 INDUCTOR CHIP 0UH
FB022 1-414-235-11 INDUCTOR CHIP 0UH

FB023 1-414-235-11 INDUCTOR CHIP 0UH
FB024 1-414-235-11 INDUCTOR CHIP 0UH

< IC >

IC001 8-759-100-93 IC uPC393G2
IC002 8-759-531-73 IC CXD8753Q
IC003 8-752-896-31 IC CXP84632-030Q
IC004 8-759-518-23 IC X24C04S8

7-14

NL-2

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

< COIL >

L002 1-414-934-21 INDUCTOR 10uH
L003 1-414-934-21 INDUCTOR 10uH
L004 1-414-938-21 INDUCTOR 47uH
L006 1-414-934-21 INDUCTOR 10uH
L007 1-414-934-21 INDUCTOR 10uH

L008 1-414-940-21 INDUCTOR 100uH
L009 1-414-936-21 INDUCTOR 22uH
L010 1-414-936-21 INDUCTOR 22uH

R033 1-216-063-91 RES,CHIP 3.9K 5% 1/10W
R035 1-249-398-11 CARBON 27 5% 1/4W F
R036 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R037 1-216-295-00 METAL CHIP 0 5% 1/10W
R038 1-216-063-91 RES,CHIP 3.9K 5% 1/10W

R039 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R040 1-216-121-91 RES,CHIP 1M 5% 1/10W
R041 1-216-073-00 METAL CHIP 10K 5% 1/10W
R042 1-216-073-00 METAL CHIP 10K 5% 1/10W
R046 1-216-295-00 METAL CHIP 0 5% 1/10W

POWER BLOCK SR821

< IC LINK >

! PS001 1-533-901-11 LINK, IC 125mA
! PS002 1-533-587-11 LINK, IC 400mA

< TRANSISTOR >

Q001 8-729-044-60 TRANSISTOR 2SC3383-T-AA
Q002 8-729-044-60 TRANSISTOR 2SC3383-T-AA
Q003 8-729-421-19 TRANSISTOR UN2213
Q004 8-729-010-25 TRANSISTOR MSD601-RT1
Q005 8-729-010-25 TRANSISTOR MSD601-RT1

Q006 8-729-010-25 TRANSISTOR MSD601-RT1
Q007 8-729-010-25 TRANSISTOR MSD601-RT1
Q008 8-729-044-60 TRANSISTOR 2SC3383-T-AA
Q009 8-729-421-19 TRANSISTOR UN2213
Q010 8-729-421-19 TRANSISTOR UN2213

Q011 8-729-044-60 TRANSISTOR 2SC3383-T-AA
Q012 8-729-421-19 TRANSISTOR UN2213
Q015 8-729-421-19 TRANSISTOR UN2213
Q016 8-729-010-05 TRANSISTOR MSB709-RT1
Q017 8-729-010-05 TRANSISTOR MSB709-RT1

Q018 8-729-010-05 TRANSISTOR MSB709-RT1
Q019 8-729-010-05 TRANSISTOR MSB709-RT1

< RESISTOR >

R048 1-216-089-00 METAL CHIP 47K 5% 1/10W
R051 1-216-045-00 METAL CHIP 680 5% 1/10W
R053 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R054 1-216-025-91 RES,CHIP 100 5% 1/10W
R057 1-216-025-91 RES,CHIP 100 5% 1/10W

R058 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R060 1-216-045-00 METAL CHIP 680 5% 1/10W
R061 1-216-045-00 METAL CHIP 680 5% 1/10W
R063 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R064 1-216-025-91 RES,CHIP 100 5% 1/10W

R067 1-216-025-91 RES,CHIP 100 5% 1/10W
R068 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R070 1-216-045-00 METAL CHIP 680 5% 1/10W
R071 1-216-041-00 METAL CHIP 470 5% 1/10W
R072 1-216-041-00 METAL CHIP 470 5% 1/10W

R073 1-216-041-00 METAL CHIP 470 5% 1/10W
R074 1-216-041-00 METAL CHIP 470 5% 1/10W
R081 1-216-089-00 METAL CHIP 47K 5% 1/10W
R082 1-216-089-00 METAL CHIP 47K 5% 1/10W
R083 1-216-043-91 RES,CHIP 560 5% 1/10W

< VIBRATOR >

X001 1-767-914-21 VIBRATOR, CRYSTAL 13.56MHz
X002 1-760-995-21 VIBRATOR, CRYSTAL 16MHz

************************************************************

R002 1-249-402-11 CARBON 56 5% 1/4W F
R004 1-216-049-00 METAL CHIP 1K 5% 1/10W
R005 1-216-049-00 METAL CHIP 1K 5% 1/10W
R007 1-249-398-11 CARBON 27 5% 1/4W F
R008 1-216-049-00 METAL CHIP 1K 5% 1/10W

R009 1-216-295-00 METAL CHIP 0 5% 1/10W
R010 1-216-049-00 METAL CHIP 1K 5% 1/10W
R011 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R012 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R013 1-216-065-91 RES,CHIP 4.7K 5% 1/10W

R014 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R015 1-216-025-91 RES,CHIP 100 5% 1/10W
R016 1-216-089-00 METAL CHIP 47K 5% 1/10W
R017 1-216-081-00 METAL CHIP 22K 5% 1/10W
R018 1-216-025-91 RES,CHIP 100 5% 1/10W

R019 1-216-089-00 METAL CHIP 47K 5% 1/10W
R020 1-216-081-00 METAL CHIP 22K 5% 1/10W
R022 1-216-049-00 METAL CHIP 1K 5% 1/10W
R023 1-216-017-91 RES,CHIP 47 5% 1/10W
R024 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

R025 1-216-049-00 METAL CHIP 1K 5% 1/10W
R027 1-249-402-11 CARBON 56 5% 1/4W F
R030 1-216-017-91 RES,CHIP 47 5% 1/10W
R031 1-216-073-00 METAL CHIP 10K 5% 1/10W
R032 1-216-065-91 RES,CHIP 4.7K 5% 1/10W

! 1-468-308-11 POWER BLOCK SR821

******************

< CAPACITOR >

! C101 1-104-705-51 FILM 0.1uF 250V
! C102 1-104-705-51 FILM 0.1uF 250V

C106 1-119-882-41 ELECT 120uF 200V
C107 1-126-963-11 ELECT 4.7uF 50V
C110 1-130-491-51 FILM 0.047uF 50V

C111 1-130-491-51 FILM 0.047uF 50V
C201 1-126-967-11 ELECT 47uF 50V
C202 1-126-183-11 ELECT 1000uF 16V
C203 1-126-934-11 ELECT 220uF 16V
C204 1-111-044-11 ELECT 2200uF 16V

C205 1-126-925-11 ELECT 470uF 10V
C206 1-126-967-11 ELECT 47uF 50V
C207 1-126-925-11 ELECT 470uF 10V
C208 1-126-960-11 ELECT 1uF 50V

Note :

The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number

7-15

specified.

(Ref. No.: 9,000 Series)

Note :

Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.

POWER BLOCK SR821

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

< DIODE >

D103 8-719-920-32 DIODE ERA15-02
D104 8-719-109-61 DIODE RD3.0ES
D105 8-719-911-19 DIODE 1SS119
D106 8-719-904-05 DIODE 1N4005
D107 8-719-904-05 DIODE 1N4005

D108 8-719-904-05 DIODE 1N4005
D109 8-719-904-05 DIODE 1N4005
D110 8-719-904-05 DIODE 1N4005
D201 8-719-061-02 DIODE PR1003
D202 8-719-510-73 DIODE S3L20U

D204 8-719-027-20 DIODE D3S4M
D205 8-719-058-08 DIODE RD51F
D206 8-719-061-02 DIODE PR1003
D207 8-719-061-02 DIODE PR1003

< FUSE >

! F101 1-533-296-11 FUSE 2A 125V

< FERRITE BEAD >

FB1 9-902-053-01 FERRITE BEAD

< IC >

! IC201 8-759-420-19 IC AN1431T

< PHOTOCOUPLER >

1-475-749-11 COMMANDER, STANDARD (RMT-V249)
1-696-592-11 CORD, CONNECTION (NTSC) (FOR RF) 1.5m
1-775-454-21 CORD, CONNECTION (MONAURAL CABLE)

1-776-258-11 CORD, AVC CONNECTION (FOR VIDEO/AUDIO)

1-783-325-11 CORD, CONNECTION (CABLE MOUSE)

3-861-573-11 MANUAL, INSTRUCTION (ENGLISH)
3-861-573-21 MANUAL, INSTRUCTION (FRENCH) (Canadian)
3-861-573-31 MANUAL, INSTRUCTION (CHINESE) (Canadian)
3-979-315-01 COVER, JACK

* 3-979-317-01 CUSHION

* 3-979-512-01 SPACER
* 3-987-412-01 INDIVIDUAL CARTON

************************************************************

#1 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
#2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
#701 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
#702 7-682-547-04 SCREW +P 3X6
#703 7-685-133-19 SCREW (DIA. 2.6) (IT3B)

ACCESSORIES & PACKING MATERIALS

*******************************

1.5m

1.5m

*************

HARDWARE LIST

*************

! PC101 8-719-018-29 PHOTOCOUPLER ON3131

< TRANSISTOR >

Q101 8-729-904-98 TRANSISTOR 2SC4054
Q102 8-729-012-31 TRANSISTOR 2SC4040

< RESISTOR >

! R101 1-219-779-51 CARBON 6.8M 10% 1/2W
************************************************************

MISCELLANEOUS

*************

1-666-524-11 PWB, CA-55
1-766-723-21 CONNECTOR, BOARD TO BOARD 3P

! 9 1-783-605-11 CORD, POWER

11 1-762-844-21 SWITCH, ROTARY
14 1-783-546-11 CABLE, FLAT (FFM-24)

16 1-783-547-11 CABLE, FLAT (FFM-25)
21 1-475-749-11 COMMANDER, STANDARD (RMT-V249)

! 54 1-468-308-11 POWER BLOCK SR821

56 1-779-725-11 CONNECTOR, BOARD TO BOARD 5P
704 1-500-144-11 HEAD, FE

776 8-839-044-02 DRUM ASSY DZH-94A/Z-RP (M901)
M902 1-698-971-11 MOTOR, DC (SPINDLE)
M903 X-3947-577-1 MOTOR ASSY, CAM

************************************************************

7-16E

Note :

The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.

Note :

Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.