Sony RMT-V293A, RMT-V294A, SLV-LX40, SLV-LX50, SLV-LX50CL Service Manual

...

— 1 —

LX40/LX50/LX60S/LX70S

RMT-V293A/V294A

Chilean Model

SLV-LX50CL/LX50CS/LX70SCL/

LX70SCS

Mexican Model

SLV-LX40MX/LX50MX/LX60SMX/

LX70SMX

Panama Model

Venezuelan Model

SLV-LX50PA/LX50PC/LX50VZ/

LX70SPA/LX70SPC/LX70SVZ

SERVICE MANUAL

VIDEO CASSETTE RECORDER

S MECHANISM

Refer to the SERVICE MANUAL of VHS MECHANICAL ADJUSTMENT

for MECHANICAL ADJUSTMENTS.

(9-921-748-11)

SPECIFICATIONS

HiFi model : SLV-LX60S/LX70S Mono model: SLV-LX40/LX50

System

Format

VHS NTSC standard

Video recording system

Rotary head helical scanning FM system

Video heads

Double azimuth four heads

Video signal

NTSC color, EIA standards

Tape speed

SP: 33.35 mm/s EP: 11.11 mm/s LP: 16.67 mm/s, playback only

Maximum recording/playback time

9 hrs. in EP mode (with T-180 tape)

Fast-forward and rewind time

Approx. 3 min. (with T-120 tape)

Tuner section

Channel coverage

VHF 2 to 13 UHF 14 to 69 CATV A-8 to A-1, A to W, W+1 to W+84

Antenna

75-ohm antenna terminal for VHF/UHF

Input and outputs

LINE-1 IN and -2 IN

VIDEO IN, phono jack (1 each) Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO IN, phono jacks (1 each) (SLV-LX50

and LX40), (2 each) (SLV-LX70S and LX60S) Input level: 327 mVrms Input impedance: more than 47 kilohms

LINE OUT

VIDEO OUT, phono jack (1) Output signal: 1 Vp-p, 75 ohms, unbalanced,

sync negative AUDIO OUT, phono jacks (1 each) (SLV-LX50

and LX40), (2 each) (SLV-LX70S and LX60S) Standard output: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms

Timer section

Clock

Quartz locked

Timer indication

12-hour cycle

Timer setting

8 programs (max.)

Power back-up

Built-in self-charging capacitor Back-up duration: up to 8 hours at a time

General

Power requirements

110 V AC to 240 V AC, 50/60 Hz (SLV-LX70S (CL/CS) and LX50 (CL/CS)) 120 V AC, 60 Hz (SLV-LX70S (MX/PA/PC/VZ), LX60S (MX),

LX50 (MX/PA/PC/VZ), and LX40 (MX))

Power consumption

17 W (SLV-LX70S (CL/CS/MX/PA/PC/VZ) and SLV-LX60S (MX))

16 W (SLV-LX50 (CL/CS/MX/PA/PC/VZ) and SLV-LX40 (MX))

Operating temperature

5°C to 40°C (41°F to 104°F)

Storage temperature

–20°C to 60°C (–4°F to 140°F)

Dimensions

Approx. 355 x

96 x 288.8 mm (w/h/d)

including projecting parts and controls

Mass

Approx. 3.6 kg

Supplied accessories

Remote commander (1) Size AA (R6) batteries (2) 75-ohm coaxial cable with F-type connectors (1) Audio/video cable (1) (3-phono to 3-phono)

(SLV-LX70S and LX60S only) Plug adaptor (1)

(SLV-LX70S (CL/CS) and LX50 (CL/CS) only)

Design and specifications are subject to change without notice

ENERGY STAR

is a U.S. registered mark.

As an ENERGY STAR

Partner, Sony Corporation has determined that this product meets the ENERGY STAR

123

456

789

SLV-LX70S

— 2 —

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

— 3 —

TABLE OF CONTENTS

SERVICE NOTE

1. ERROR CODE INDICATION ........................................... 5

1 GENERAL

Getting Started ...........................................................................1-1

Step 2 : Setting up the remote commander .............................1-1

Step 3 : Hookups .....................................................................1-1

Selecting a language ...............................................................1-4

Setting the clock ...................................................................... 1-4

Presetting channels.................................................................. 1-6

Basic Operations........................................................................ 1-8

Playing a tape ..........................................................................1-8

Recording TV programs.......................................................... 1-8

Recording TV programs using the Dial Timer........................ 1-9

Recording TV programs using the Timer ............................. 1-10

Additional Operations .............................................................1-11

Locking the VCR (Child Lock)............................................. 1-11

Playing/searching at various speeds...................................... 1-11

Setting the recording duration time....................................... 1-12

Checking/changing/canceling timer settings ........................ 1-12

Recording stereo and bilingual programs ............................. 1-13

Searching using for the begining of a timer recorded

program .........................................................................1-13

Searching using the index function .......................................1-13

Searching using the time search function ............................. 1-14

Skip-searching automatically (Quick view).......................... 1-14

Searching for a selected point on the tape ............................1-14

Adjusting the picture .............................................................1-15

Changing menu options ........................................................ 1-15

Editing with another VCR.....................................................1-16

Additional Information ............................................................1-16

General setup information..................................................... 1-16

Index to parts and controls ....................................................1-18

2 DISASSEMBLY

2-1. CASE, FRONT PANEL BLOCK ASSEMBLY ..............2-1

2-2. DI-80 BOARD, FJ-32BOARD ........................................ 2-1

2-3. REAR PANEL .................................................................2-2

2-4. MA-405 BOARD ............................................................2-2

2-5. MECHANISM DECK .....................................................2-3

2-6. INTERNAL VIEWS ........................................................2-4

2-7. CIRCUIT BOARDS LOCATION ................................... 2-5

3 BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM ....................................3-1

3-2. VIDEO BLOCK DIAGRAM .......................................... 3-3

3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM .....3-5

3-4. TUNER BLOCK DIAGRAM ......................................... 3-7

3-5. AUDIO BLOCK DIAGRAM ..........................................3-9

3-6. POWER BLOCK DIAGRAM....................................... 3-11

4 PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM ................................4-3

4-2. PRINTED WIRING BOARDS AND SCHEMATIC

DIAGRAMS .................................................................... 4-5

• MA-405 (VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, POWER)

PRINTED WIRING BOARD .........................4-5

• MA-405 (1/7)(REC/PB HEAD AMP)

SCHEMATIC DIAGRAM ..............................4-7

• MA-405 (2/7)(Y/C, AUDIO PROCESS)

SCHEMATIC DIAGRAM ..............................4-9

• MA-405 (3/7)(SERVO/SYSTEM CONTROL)

SCHEMATIC DIAGRAM ............................4-11

• MA-405 (4/79)(AUDIO PROCESS)

SCHEMATIC DIAGRAM ............................4-13

• MA-405 (5/7)(TUNER)

SCHEMATIC DIAGRAM ............................4-15

• MA-405 (6/7)(DISPLAY CONTROL)

SCHEMATIC DIAGRAM ............................4-17

• MA-405 (7/7)(POWER SUPPLY)

SCHEMATIC DIAGRAM ............................4-19

• FJ-32 (LINE-2 IN) PRINTED WIRING BOARD AND

SCHEMATIC DIAGRAM ............................4-23

• DI-80 (DIAL TIMER) PRINTED WIRING BOARD AND

SCHEMATIC DIAGRAM ............................4-24

5 INTERFACE, IC PIN FUNCTION

DESCRIPTION

5-1. SYSTEM CONTROL — MECHANISM BLOCK

INTERFACE (MA-405 BOARD IC160) ....................... 5-1

5-2. SYSTEM CONTROL — SERVO PERIPHERAL

CIRCUIT INTERFACE (MA-405 BOARD IC160) ...... 5-1

5-3. SYSTEM CONTROL — SYSTEM CONTROL

PERIPHERAL CIRCUIT INTERFACE

(MA-405 BOARD IC160).............................................. 5-2

5-4. SYSTEM CONTROL AND RF MODULATOR

— INPUT SELECTION BLOCK INTERFACE

(MA-405 BOARD IC160).............................................. 5-2

5-5. SYSTEM CONTROL — VIDEO/RP BLOCK

INTERFACE (MA-405 BOARD IC160) ....................... 5-2

5-6. SYSTEM CONTROL — AUDIO BLOCK INTERFACE

(MA-405 BOARD IC160).............................................. 5-2

5-7. SERVO/SYSTEM CONTROL MICROPROCESSOR

PIN FUNCTIONS (MA-405 BOARD IC160)............... 5-3

6 ADJUSTMENTS

6-1 MECHANICAL ADJUSTMENTS ................................. 6-1

6-2. ELECTRICAL ADJUSTMENTS ...................................6-1

2-1. PREPARATION BEFORE ADJUSTMENT ...................6-1

2-1-1.Equipment Required ..................................................... 6-1

2-1-2.Equipment Connection ................................................. 6-1

2-1-3.Set-up of Adjustment ....................................................6-1

2-1-4.Alignment Tape............................................................. 6-1

2-1-5.Input/Output Levels and Impedance .............................6-2

2-1-6.Adjustment Sequence ................................................... 6-2

2-2. POWER SUPPLY CHECK .............................................6-2

2-2-1.Output Voltage Check (MA-405 Board) ......................6-2

2-3. SERVO SYSTEM CHECK .............................................6-3

2-3-1.RF Switching Position Adjustment (MA-405 Board)...6-3

2-4. AUDIO SYSTEM ADJUSTMENT................................. 6-3

2-4-1.Hi-Fi Audio System Adjustment (Hi-Fi model only) ...6-3 2-4-2.HiFi Switching Position Adjustment (MA-405 Board) 6-4

2-4-3. Normal Audio System Adjustment ...............................6-4

2-4-4.Audio Level and Distortion Check ............................... 6-4

2-4-5.Audio Noise Check .......................................................6-4

2-4-6.ACE Head Adjustment..................................................6-4

2-4-7.E-E Output Level Check ...............................................6-4

2-4-8.Frequency Response Check ..........................................6-4

2-5. ADJUSTING PARTS LOCATION DIAGRAM ............. 6-6

7 REPAIR PARTS LIST

7-1. EXPLODED VIEWS ......................................................7-1

7-1-1.FRONT PANEL AND UPPER CASE SECTION ........7-1

7-1-2.CHASSIS SECTION .................................................... 7-2

7-1-3.MECHANISM DECK SECTION-1 .............................7-3

7-1-4.MECHANISM DECK SECTION-2 .............................7-4

7-1-5.MECHANISM DECK SECTION-3 .............................7-5

7-2. ELECTRICAL PARTS LIST ..........................................7-6

Section Title Page Section Title Page

— 4 —

1. ERROR CODE INDICATION

• Error codes are indicated using the lower 5 digits in the fluorescent display tube. “At this time, Colon “:” between character is not indicated.”

ERROR CODE

MODE CODE

0 Power-on eject 10 FWD x1 20 REW play 1 Power-on initial 11 FWD x2 21 Cas. loading 2 Power-off eject 12 CUE 22 Tape loading 3 Power-off stop 13 PB-pause 23 Power-off loading 4 FF 14 RVS-pause 24 Mecha. error (Power on) 5 REW 15 RVS x1 25 Power-on eject initial 6 REC 16 RVS x2 26 Power-off eject initial 7 REC- pause 17 REV 27 APC REC 8 Power-on stop 18 Power-off initial 28 Cas. loading 9 PB 19 Mecha. error (Power off) (No auto PB check)

0 No error 1 Cam encoder error Loading direction 2 Cam encoder error Unloading direction 3 T reel error 4 S reel error 5 Capstan error 6 Drum error 7 Error on initializing 8 Cassette loading error 9 Reserve

SERVICE NOTE

Mode code indication when the error has occurred.

Error code

1-1

SECTION 1

GENERAL

SLV-LX40/LX50/LX60S/LX70S

Setting up the remote commander

Step 2 : Setting up the remote commander

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove the batteries

to avoid possible damage from battery leakage.

• Do not use a new battery with an old one.

• Do not use different types of b atteries.

Inserting the batteries

Insert two size AA (R6) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.

Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.

Using the remote commander

You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV.

To operate Set •TV / VIDEO to

the VCR VIDEO

and point at the remote sensor at the VCR

a Sony TV •TV

and point at the remote sensor at the TV

123

•TV / VIDEO

Remote sensor

continued

Setting up the remote commander

Controlling other TVs with the remote commander (SLV-LX70S and LX60S only)

The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number.

Now you can use the ?/1, VOL +/–, CH +/–, and TV/VIDEO buttons to control your TV. Yo u can also use the buttons marked with a dot (•) to control a Sony TV. To control the VCR, reset •TV

/ VIDEO to VIDEO.

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

Notes

• If you enter a new code num ber, the code number previously entered will be erased.

• If the TV uses a different remote control system from the one programmed to work with the

VCR, you cannot control your TV with the remote commander.

• When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time yo u replace the batteries.

• When you press the AUDIO MONITOR button, your TV’s menu may appear on the TV screen. To exit the TV menu, press the MENU button on the TV remote commander or wait until the menu disappears autom atically.

Set •TV / VIDEO at the top of the remote commander to •TV.

Hold down ?/1, and enter your TV’s code number using the number buttons. Then release ?/1.

TV brand

Code number

Sony 01

Akai 04

AOC 04

Centurion 12

Coronado 03

Curtis-Mathes 12

Daytron 12

Emerson 03, 04, 14

Fisher 11

General Electric 06, 10

Gold Star 03, 04, 17

Hitachi 02, 03

J.C.Penney 04, 12

JVC 09

KMC 03

Magnavox 03, 08, 12

Marantz 04, 13

MGA/Mitsubishi

04, 12, 13, 17

NEC 04, 12

Panasonic 06, 19

Philco 03, 04

Philips 08

Pioneer 16

Portland 03

Quasar 06, 18

Radio Shack 05, 14

TV brand

Code number

RCA 04, 10

Sampo 12

Sanyo 11

Scott 12

Sears 07, 10, 11

Sharp 03, 05, 18

Sylvania 08, 12

Teknika 03, 08, 14

Tosh ib a 0 7

Wards 03, 04, 12

Yor x 12

Zenith 15

TV brand

Code number

Hookups

Step 3 : Hookups

Selecting the best hookup option

There are many ways in which your VCR can be hooked up. To hook up your VCR so that it works best for you, first scan through the table below. Then use the accompanying diagrams and procedures on the following pages to set up your VCR.

If your TV has audio/video inputs, refer to pages 8 and 9 for audio/video (A/V) hookup. Then follow one of the hookups below. If your TV doesn’t have A/V inputs, go directly to one of the hoo kups below.

After you’ve completed the connections, follow the instructions for setup. During setup, if you need more details o n the procedure described, page numbers are provided where you can find comple te, step-by-step instructions.

After you’ve completed the setup, you’re ready to use your VCR. Procedures differ depending on the hookup you used. For an overview, refer to “Quick reference to using the VCR” on the back cover.

Before you get started

• Turn off the power to all equipment.

• Do not connect the AC power cords until all of the connections are completed.

• Be sure to make connections firmly. Loose connections may cause picture

distortion.

• If your TV doesn’t match any of the examples provided, see your nearest Sony dealer or qualified technician.

If you have Use Refer to

Antenna only, no cable TV Hookup 1 Pages 10 to 11

No cable box or cable box with only a few scrambled channels

Hookup 2 Pages 12 to 14

Cable box with many scrambled channels Hookup 3 Pages 15 to 17

Hookups

Audio/video (A/V) hookup

If your TV has audio/video (A/V) input jacks, you will get a better picture and sound if you hook up your VCR using these connections. If your TV doesn’t have A/V inputs, see the following pages for antenna or cable hookups.

If you’re not planning to use your VCR to record programs, you’re finished setting up the VCR after you’ve made the connections shown on pages 8 and 9. If you want to record regular or cable TV programs, complete these connections first, and then go to the following pages for antenna or cable hookups.

For SLV-LX70S and LX60S

For a true “home theater” experience, you should connect the audio outputs of your VCR or TV to your stereo system.

A Use this hookup if your TV has stereo jacks

B Use this hookup if your TV doesn’t have stereo jacks

Notes

• If you don’t have a stereo receiver, connect the white LINE OUT/AUDIO L jack to the AUDIO IN jack on your TV.

• To play a tape in stereo, you must use th e A/V connection.

• If you use the Trinitron TV Synchro Play function (see page 34), the A/V connection is

necessary. (If your TV has two or more inputs, connect the audio/video cable to the VIDEO IN 1 jacks.)

VIDEO

AUDIO

AUDIO OUT

AUX IN

LINE-1 IN

LINE OUT

AUDIO VIDEO

Audio/video cable (supplied)

Audio cable (not supplied)

Stereo receiverVCR

VIDEO AUDIO

AUX IN

LINE-1 IN

LINE OUT

AUDIO VIDEO

Video cable (not supplied)TVAudio cable (not supplied)

Stereo receiverVCR

This section is a translated version of Instruction Manual SLV-LX70S model Part number: 3-065-284-12

1-2

Hookups

For SLV-LX50 and LX40

A Use this hookup if your TV has stereo jacks

B Use this hookup if your TV doesn’t have stereo jacks

Note

• If you use the Trinitron TV S ynchro Play function (see page 34), the A/V connecti on is necessary. (If your TV has two or more i nputs, connect the audio/video cable to the VIDEO IN 1 jacks.)

Completing A/V hookup

After you’ve connected your TV and completed antenna or cable hookup, return to this procedure to complete VCR set up. This will prevent unwanted noise in the RF channel.

LINE-1 IN

LINE OUT

AUDIO VIDEO

VIDEO

AUDIO

Audio/video cable (not supplied)

VCR

VIDEO AUDIO

LINE-1 IN

LINE OUT

AUDIO VIDEO

Audio/video cable (not supplied)

VCR

PROG. / VERIF.

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

AJUSTES

OPCIONES

ESTEREO AUTO.

SELEC. AUTO. ANT.

SINTONIZ. AUDIO SELC. DE CINTA

AUTO

VEL. AUTO. CINTA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

1PÁGINA

Press MENU and select OPCIONES.

Set SELEC. AUTO. ANT. to NO and press OK.

For details, see page 62.

Hookups

Hookup 1

Antenna hookup

Make the following connections if you’re using an antenna (if you don’t have cable TV).

A Use this hookup if you’re using:

• VHF/UHF antenna (you get channels 2–13 and channels 14 and higher)

• UHF-only antenna (you get channels 14 and higher)

• Separate VHF and UHF antennas

B Use this hookup if you’re using a VHF-only antenna (you get

channels 2–13 only)

If you cannot connect your antenna cable to the VCR directly

If your antenna cable is a flat cable (300-ohm twi n lead cable), attach an external antenna connector (not supplied) s o you can connect the cable to the VHF/UHF IN connector. If you have separate cables for VHF and UHF antennas, you should use a U/V band mixer (not supplied). For details, see page 68.

OUT

VHF/UHF

Rear of TV VHF/UHF

VHF

Match the type of connector on your TV: A, B, or C.

UHF

VCR

OUT

VHF/UHF

Rear of TV VHF/UHF

VHF

Match the type of connector on your TV: A, B, or C.

UHF

VCR

For connector type

B and C, no UHF connection is required.

Hookups

Hookup 1 : VCR setup

Before you start…

• Turn on the VCR and the TV.

• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.

You have now completed hookup.

Set the RF UNIT switch to CH3 or CH4, whichever channel is not used in your area. If both are used, set the switch to either channel. For details, see page 67. If you made A/V connections (from page 8), you do not need to adjust the RF UNIT switch.

Change the on-screen display language to E nglish, if desired. For details, see page 18.

Press EASY SET UP on the VCR.

1 The RELOJ menu appears. Select MANUAL

and press OK. Then set the clock. For details, see page 24.

2 The SINTONIZADOR menu appears. Set

ANTENA/CABLE to ANT and press OK. For details, see page 26.

3 The AJUSTE AUTO. starts.

CH3

RF UNIT

CH4

EASY SET UP

SELECCIONAR :

AUTO MANUAL

AJUSTE RELOJ

EASY SET UPCANCELAR :

AJUSTE SINTONIZADOR

ANTENA / CABLE

CABLE

ANT

SELECCIONAR :

EASY SET UPCANCELAR :

AJUSTE

AJUSTE CONCLUIDO

POR FAVOR ESPERE

AJUSTE SINTONIZADOR

AJUSTE AUTO.

EJECUTANDO

CH 2 4

Hookups

Hookup 2

You have no cable box, or a cable box with only a few scrambled channels

Recommended use

Use this hookup if you do n ot have a cable box. Also use this hookup if your c able system scrambles only a few channels.

What you can do with this hookup

• Record any unscrambled channel by selecting the channel on the VCR

What you can’t do

• Record scrambled channels that re quire a cable box

OUT

VHF/UHF

IN OUT

Rear of TV

VHF/UHF

VHF

UHF

VCR

Match the type of connector on your TV: A, B, or C.

For connector types B and C, no UHF connection is required.

VHF

UHF

Wall

Cable box

Connect this cable directly to your TV if you don’t have a cable box.

1-3

Hookups

Hookup 2 : VCR setup

Before you start…

• Turn on the VCR and the TV.

• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.

Set the RF UNIT switch to CH3 or CH4, whichever channel is not used in your area. If both are used, set the switch to either channel. For details, see page 67.

If you made A/V connections (from page 8), you do not need to adjust the RF UNIT switch.

Change the on-screen display language to E nglish, if desired. For details, see page 18.

Press EASY SET UP on the VCR.

1 The RELOJ menu appears. Select AUTO and

press OK. For details, see page 20.

2 The PAIS/ZONA DE HORARIO menu

appears. Select the country you want to set and press OK. You can select the following countries: BELIZE y BOLIVIA y CHILE y COLOMBIA y COSTA RICA y CUBA y REP. DOMIN. y ECUADOR y EL SALVADR y GUATEMALA y GUYANA y HONDURAS y JAM AICA y MEX-CENTRO y MEX-MONT. y ME X- PAC IF. y MEX-S. ESTE y NICARAGUA y PANA MA y PERU y SURINAM y TRIN. & TOB. y VENEZUELA

CH3

RF UNIT

CH4

EASY SET UP

SELECCIONAR :

AUTO MANUAL

AJUSTE RELOJ

EASY SET UPCANCELAR :

SELECCIONAR :

BELIZE BOLIVIA CHILE COLOMBIA COSTA RICA CUBA REP. DOMIN. ECUADOR EL SALVADR

AJUSTE PAIS / ZONA DE HORARIO

EASY SET UPCANCELAR :

continued

Hookups

You have now completed hookup.

Automatic clock setting

Once you’ve set up the VCR, it automatically sets the clock the first time you turn off the VCR. “ACS” (Auto Clock Set) wil l flash in the display window and search for a time signal provided by Sony Entertainment Television (SETV). After that , whenever you turn off the VCR, it checks the time and adjusts the c lock, even for Daylight Saving Time.

If you want to use the timer to record right away, or if the cable TV station in your area does not broadcast SETV, or if SETV in your area does not carry time sign als, set the clock manually. For details, see page 23.

Notes

• If the clock is not set, “ACS ” will flash in the display window whenever the VCR is turned off. During this time, the VCR will search for a time signal.

• The Daylight Saving Time start and end days m ay differ depending on the year. To ensure correct switchin g, select SI or NO for th e HORARIO VERANO setting ( page 22).

3 The SINTONIZADOR menu appears. Set

ANTENA/CABLE to CABLE and press OK. For details, see page 26.

4 The AJUSTE AUTO. starts.

AJUSTE SINTONIZADOR

ANTENA / CABLE

CABLE

ANT

SELECCIONAR :

OK EASY SET UPCANCELAR :

AJUSTE

AJUSTE CONCLUIDO

POR FAVOR ESPERE

AJUSTE SINTONIZADOR

AJUSTE AUTO.

EJECUTANDO

CH 2 4

Hookups

Hookup 3

Connecting a cable box with many scrambled channels

Recommended use

Use this hookup if your cable system scrambles all or most channels.

What you can do with this hookup

• Record any channel by selecting the channel o n the cable box

What you can’t do

• Record with the cable box turned off

• Record one channel while watch ing another channel

OUT

VHF/UHF

IN OUT

Rear of TV

VHF/UHF

VHF

UHF

VCR

Match the type of connector on your TV: A, B, or C.

For connector types B and C, no UHF connection is required.

Cable box

VHF

UHF

Wall

continued

Hookups

Hookup 3 : VCR setup

Before you start…

• Turn on the VCR and the TV.

• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.

Set the RF UNIT switch to CH3 or CH4, whichever channel is not used in your area. If both are used, set the switch to either channel. For details, see page 67.

If you made A/V connections (from page 8), you do not need to adjust the RF UNIT switch.

Turn on your cable box.

Change the on-screen display language to English, if desired. For d etails, see page 18.

Press EASY SET UP on the VCR.

1 The RELOJ menu appears. Sel ect AUTO and

press OK. For details, see page 20.

2 The PAIS/ZONA DE HORARIO menu

CH3

RF UNIT

CH4

EASY SET UP

SELECCIONAR :

AUTO MANUAL

AJUSTE RELOJ

EASY SET UPCANCELAR :

SELECCIONAR :

BELIZE BOLIVIA CHILE COLOMBIA COSTA RICA CUBA REP. DOMIN. ECUADOR EL SALVADR

AJUSTE PAIS / ZONA DE HORARIO

EASY SET UPCANCELAR :

1-4

Hookups

Automatic clock setting

Once you’ve set up the VCR, it automatically sets the clock the first time you turn off the VCR. “ACS” (Auto Clock Set) will flash in the display window and search for a time signal provided by Sony Entertainment Television (SETV). After that, whenever you turn off the VCR, it checks the time and adjusts the clock, even for Daylight Saving Time.

To use the Auto Clock Set feature with this hookup, you need to manually select SETV:

You have now completed hookup If you want to use the timer to record right away, or if the cable TV station in your

area does not broadcast SETV, or if SETV in your area does not carry time signals, set the clock manually. For details, see page 23.

Notes

• To use the Auto Clock Set feature, leave the cable box on.

• If the clock is not set, “ACS” will flash in the display window whenever the VCR is turned

off. During this time, the VCR will search for a time signal.

• The Daylight Saving Time start and en d days may differ depending on the year. To ensure correct switching, select SI or NO for the HORARIO VERANO settin g (page 22).

3 The SINTONIZADOR menu appears. Set

ANTENA/CABLE to ANT and press OK. For details, see page 26.

4 The AJUSTE AUTO. starts.

Tune the cable box to SETV.

Select AUTO in the RELOJ menu to turn on the Auto Clock Set feature.

Turn off the VCR. It automatically sets the clock and adjusts for Daylight Saving Time by picking up the time signal.

AJUSTE SINTONIZADOR

ANTENA / CABLE

CABLE

ANT

SELECCIONAR :

EASY SET UPCANCELAR :

AJUSTE

AJUSTE CONCLUIDO

POR FAVOR ESPERE

AJUSTE SINTONIZADOR

AJUSTE AUTO.

EJECUTANDO

CH 2 4

Selecting a language

Tip

• If you want to return to the previous menu , highlight VOLVER and press OK.

You can change the on-screen display language.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the VCR channel (channel 3

or 4). If your TV is connected to the VCR using A/V connections, set the TV to video input.

• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.

Press MENU, then press M/m to highlight AJUSTES and press OK.

Press M/m to highlight SELECCION DEL IDIOMA, then press OK.

Press M/m to highlight ENGLISH or ESPAÑOL, then press OK.

M/m

PLAY

AJUSTES

PREAJUSTE DEL SINTONIZADOR AJUSTE DEL RELOJ SELECCION DEL IDIOMA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

PLAY

SELECCION DEL IDIOMA

ENGLISH ESPAÑOL

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

PLAY

Setting the clock

Using the Auto Clock Set feature

Sony Entertainment Television (SETV) transmits time signals with its broadcasts. If the cable TV station in your ar ea broadcasts SETV and transmits these time signals, your VCR can pick up these time signals to automatically set the clock.

The Auto Clock Set feature works only if SETV in your area broadcasts time signals. If SETV in your area does not broadcast tim e signals or if you select Hookup 1 on page 10 set the time manually (page 23).

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the VCR channel (channel 3

or 4). If your TV is connected to the VCR using A/V connections, set the TV to vi deo input.

• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.

Press MENU, then press M/m to highlight AJUSTES and press OK.

When using the EASY SET UP procedure, skip steps 1 and 2.

Press M/m to highlight AJUSTE DEL RELOJ, then press OK.

M/m

PLAY

AJUSTES

PREAJUSTE DEL SINTONIZADOR AJUSTE DEL RELOJ SELECCION DEL IDIOMA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

PLAY

AUTO MANUAL

AJUSTE DEL RELOJ

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

continued

Setting the clock

Tip

• If you want to return to the previous menu , highlight VOLVER and press OK.

Notes

• The clock cannot be set automatically if you don’t receive SETV broadcast that c arries time signals in your area. If so, set t he clock manually (page 23).

• Depending on the channels allotted to SETV in your area, setting the clock automatica lly may take up to about 30 minutes. If nothing happens even after you wait about 30 minutes after turning off the VCR, turn the VCR on and then off again. If the clock is not set even after about another 30 minut es, set the clock manually (page 23).

• If the clock is not set, “ACS ” will flash in the display window whenever the VCR is turned off. During this time, the VCR will search for a time signal.

Press M/m to highlight AUTO, then press OK.

Press M/m to highlight TOTAL. AUTO., then press OK.

Press M/m to highlight SI, then press OK.

Press MENU to exit the menu.

To activate the Auto Clock Set function, turn off the VCR. “ACS” will flash in the display window.

The VCR automatically sets the clock by searching for the SETV broadcast that carries time signals and sets Daylight Saving Time (if applicable).

If your clock is incorrectly set to Daylight Saving Time, you can adjust these settings without turning off the Auto Clock Set feature ( page 21).

PLAY

AJUSTE AUTOMATICO RELOJ

TOTAL. AUTO.

HORARIO VERANO

CH AJUSTE RELOJ

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

PLAY

AJUSTE AUTOMATICO RELOJ

TOTAL. AUTO.

CH AJUSTE RELOJ HORARIO VERANO

VOLVER

SI NO

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

PLAY

1-5

Setting the clock

If the clock does not activate

Follow steps 1 to 4 in “Using the Auto Clock Set feature.”

The TOTAL. AUTO. menu is displaye d.

123

456

789

Number buttons

M/m

AJUSTE AUTOMATICO RELOJ

TOTAL. AUTO.

CH AJUSTE RELOJ HORARIO VERANO

VOLVER

SI NO

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

continued

Setting the clock

Using Manual Clock Set

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the VCR channel (channel 3

or 4). If your TV is connected to the VCR using A/V connections, set the TV to vi deo input.

• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.

Press MENU, then press M/m to highlight AJUSTES and press OK.

When using the EASY SET UP procedure, skip steps 1 and 2.

Press M/m to highlight AJUSTE DEL RELOJ, then press OK.

M/m/</,

PLAY

AJUSTES

PREAJUSTE DEL SINTONIZADOR AJUSTE DEL RELOJ SELECCION DEL IDIOMA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

PLAY

AUTO MANUAL

AJUSTE DEL RELOJ

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

continued

Setting the clock

Tip

• If you want to return to the previous menu , highlight VOLVER and press OK.

Press M/m to highlight MANUAL, then press OK.

Press M/m to set the day.

Press , to highlight the month and press M/m to set the month.

Set the year, hour, and minutes in the same way as the month. The day of the week is set automatically.

Press OK to start the clock.

PLAY

FIN :

AJUSTAR :

OK MENU

SELECCIONAR :

LUN 1 AM00:211002/1/

AJUSTE DEL RELOJ

PARA SALIR :

PLAY

DOM 1 AM00:2182002/1/

AJUSTE DEL RELOJ

FIN :

AJUSTAR :

OK MENU

SELECCIONAR :

PARA SALIR :

PLAY

VIE 1 AM00:2182002/9/

AJUSTE DEL RELOJ

FIN :

AJUSTAR :

OK MENU

SELECCIONAR :

PARA SALIR :

PLAY

Setting the clock

Tip

• If you want to return to the previous menu , highlight VOLVER and press OK.

Notes

• The Daylight Saving Time start and end days m ay differ depending on the year. To ensure correct switchin g, select SI or NO for th e HORARIO VERANO setting.

• If nothing happen s even after you wait about 30 minutes after turning off th e VCR, turn the VCR on and then off again. If the clock is not set even after about another 30 minutes, set the clock manually (page 23).

• Some cable TV stations broadc asting SETV do not transmit time signals. If so, set the clock manually (page 23).

Press M/m to highlight NO for TOTAL. AUTO. and press OK.

Press M/m to highlight the item you want to set and press OK. Then press M/m to make the setting and press OK.

• For CH AJUSTE RELOJ Leave the setting to “– – –” to have the VCR automatically search for the SETV broadcast. Or, press the number buttons to select the SETV channel if you know it.

• For HORARIO VERANO Select SI or NO (standard time), or AUTO to have the VCR automatically set the daylight saving time.

Press MENU to exit the menu.

To activate the Auto Clock Set function, turn off the VCR. “ACS” will flash in the display window.

PLAY

AJUSTE AUTOMATICO RELOJ

TOTAL. AUTO.

CH AJUSTE RELOJ HORARIO VERANO

VOLVER

–––

AUTO

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

PLAY

123

456

789

AJUSTE AUTOMATICO RELOJ

TOTAL. AUTO.

CH AJUSTE RELOJ HORARIO VERANO

VOLVER

AJUSTAR :

USE :

OK MENUPARA SALIR :

123 AUTO

0–9

AJUSTE AUTOMATICO RELOJ

TOTAL. AUTO.

CH AJUSTE RELOJ HORARIO VERANO

VOLVER

AUTO SI NO

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

1-6

Presetting channels

Press M/m to highlight ANTENA/CABLE, then press OK.

• To preset cable TV channels: Press M/m to set ANTENA/CABLE to CABLE, then press OK.

• To preset VHF and UHF channels: Press M/m to set ANTENA/CABLE to ANT, then press OK.

Press M/m to highlight AJUSTE AUTO., then press OK.

All receivable channels are preset in numerical sequence. When no more receivable channels can be found, presetting stops and the picture from th e lowest numbered channel is displayed on the TV screen.

PLAY

PREAJUSTE DEL SINTONIZADOR

CABLE

+ SI

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

CH 1

PREAJUSTE DEL SINTONIZADOR

ANT

+ SI

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

CH 2

PLAY

PREAJUSTE DEL SINTONIZADOR

CABLE

+ SI

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

CH 1

POR FAVOR ESPERE

Presetting channels

Tips

• When receiving a VHF, UHF, or CATV channel, the display changes as follows each time you press DISPLAY.

• If you want to return to the previous m enu, highlight VOLVER and press OK.

Channel number

Remaining tape le ngth, and time counter

The bar indicator and pointer for searching for a specific place on a tape

No display

continued

Presetting channels

Presetting all receivable channels automatically

This VC R is capable o f receiving VHF channels 2 to 13, UHF channels 14 to 69 an d unscrambled CATV channels 1 to 125. First, we recommend that you preset the receivable channels in your area using automatic presetting methods. Then, if there are any unwanted channels, disable them manually. If you have already decided which channels you wish to preset, set them dire ctly using manual presetting methods.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the VCR channel (channel 3

or 4). If your TV is connected to the VCR using A/V connections, set the TV to vi deo input.

• Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.

Press MENU, then press M/m to highlight AJUSTES and press OK.

When using the EASY SET UP procedure, skip steps 1 and 2.

Press M/m to highlight PREAJUSTE DEL SINTONIZADOR, then press OK.

M/m

PLAY

AJUSTES

PREAJUSTE DEL SINTONIZADOR AJUSTE DEL RELOJ SELECCION DEL IDIOMA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

PLAY

PREAJUSTE DEL SINTONIZADOR

CABLE

+ SI

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

CH 1

continued

Presetting channels

Presetting/disabling channels manually

Press MENU, then press M/m to highlight AJUSTES and press OK.

123

456

789

CH +/–

Number buttons, ENTER

M/m

PLAY

AJUSTES

PREAJUSTE DEL SINTONIZADOR AJUSTE DEL RELOJ SELECCION DEL IDIOMA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

1-7

Presetting channels

Tip

• If you want to return to the previous m enu, highlight VOLVER and press OK.

Press M/m to highlight PREAJUSTE DEL SINTONIZADOR, then press OK.

• To preset a channel:

Press the number buttons to enter the channel number, then press ENTER.

Press OK.

Press M/m to set MANUAL to +, then press OK.

• To disable a channel:

Press CH +/– to select the channel number.

Press OK.

Press M/m to set MANUAL to –, then press OK.

Repeat step 3 to preset or disable channels as require d, then press MENU.

PLAY

PREAJUSTE DEL SINTONIZADOR

CABLE

+ SI

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

CH 1

PLAY

123

456

789

• CH

PREAJUSTE DEL SINTONIZADOR

CABLE

+ SI

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

CH 5

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

Channel to be preset

PREAJUSTE DEL SINTONIZADOR

CABLE

–

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

CH 5

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

Channel to be disabled

continued

Presetting channels

If the picture is not clear

Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. If, however, the picture of a channel is not clear, you can also use the manual tuning function.

Press MENU, then press M/m to highlight AJUSTES and press OK.

123

456

789

M/m/</,

Number buttons, ENTER

PLAY

AJUSTES

PREAJUSTE DEL SINTONIZADOR AJUSTE DEL RELOJ SELECCION DEL IDIOMA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

Presetting channels

Tips

• To select the channel in step 3 above, you can also use the CH +/– buttons. In this case, you don’t need to press ENTER.

• If you want to return to the previous m enu, highlight VOLVER and press OK.

Note

• When adjusting SINTONIA FINA, the menu may become difficult to read due to interference from the picture being received.

Press M/m to highlight PREAJUSTE DEL SINTONIZADOR, then press OK.

Press the number buttons to select the channel you want to fine-tune, then press ENTER.

Press M/m to highlight SINTONIA FINA, then press OK.

The fine tuning meter appears.

Press </, to adjust to a clearer picture, then press OK.

Note that the AFT setting switches to NO.

Press MENU to exit the menu.

PLAY

PREAJUSTE DEL SINTONIZADOR

CABLE

+ SI

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

CH 1

123

456

789

PREAJUSTE DEL SINTONIZADOR

CABLE

+ SI

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

CH 5

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

Selected channel

PLAY

PREAJUSTE DEL SINTONIZADOR

CABLE

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

CH 5

PLAY

PREAJUSTE DEL SINTONIZADOR

CABLE

+ NO

ANTENA / CABLE

AJUSTE AUTO.

MANUAL AFT SINTONIA FINA

VOLVER

CH 5

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

Playing a tape

Basic Operations

Playing a tape

Turn on your TV and set it to the video channel.

Insert a tape. The VCR turns on and starts playi ng

automatically if you insert a tape with its safety tab removed.

123

456

789

EJECT

DISPLAY

CLEAR

PLAY

REPLAY

PAU SE

STOP

REW

TRINITRON TV SYNCHRO PLAY

1-8

Playing a tape

Additional tasks

To play a recently watched scene

You can immediately rewind and playback the scene you want to watch again. During playback, press REPLAY up to four times. The VCR rewinds the tape about

ten seconds on the counter for each press of the button, and restarts playback.

To use the time counter

Press CLEAR at the point on the tape that you want to find later. The counter in the display window resets to “0:00: 00.” Search for the point afterwards by referring to the counter.

To display the counter on the TV screen, press DISPLAY.

Notes

• Tapes recorded in the LP mode on other VC Rs can be played back on this VCR but the picture quality cannot be guaranteed.

• While displaying a menu on the TV screen, you cannot use

PLAY, XPAUS E,

FF, m REW, or xSTOP buttons.

• The counter res ets to “0:00:00” whenever a tape is reinserted.

• The counter stops counting when i t comes to a portion with no recording.

Press H PLAY. When the tape reaches the end, it will rewind automatically.

To Press

Stop play

STOP

Pause play

PAUS E

Resume play after pause

PAUSE or HPLAY

Fast-forward the tape

FF during stop

Rewind the tape

REW during stop

Eject the tape

EJECT

PLAY

VIDEO

APC

continued

Playing a tape

Turning on the VCR and TV, and starting playback automatically (Trinitron TV Synchro Play)

You can only use this function if your TV is made by Sony (Trinitron TV).

How to connect to use this function

Connect the VCR and TV with the audio/video cable (see “Audio/video (A/V) hookup” on pages 8 and 9). Be sure to connect the audio/video cable to the VIDEO IN 1 jacks on the TV if the TV has two inputs or more. The TV must be placed where it will respond to the remote commander while you are pointing it at the VCR.

Operation

Make sure that the TV’s power is in standby mode. Press TRINITRON TV SYNCHRO PLAY and hold the remote commander in place

for about two seconds. The VCR and TV turn on, and the TV is set to the video channel. If there is a tape in

the VCR, playback starts automatically.

Notes

• If the Trinitron TV Synchro Play function does not work properly: – Wait a few moments, and press the button again. – Replace both of the batteries with new ones, and press the button again.

Note that this function may not opera te some Sony TVs because of the remote commander’s signal limitations.

• Do not press TRINITRON TV SYNCHRO PLAY during playback. If you do so, the TV’s input source will mo mentarily switch to the TV’s tuner.

Recording TV programs

Turn on your TV and set it to the video channel. To record from a cable box, turn it on.

Insert a tape with its safety tab in place.

123

456

789

CH +/–

REC

STOP

DISPLAY

TV/VIDEO

SP/EP

continued

Recording TV programs

To stop recording

Press x STO P.

To check the remaining tape length

Press DISPLAY repeatedly until the remaining tape length and the time counter appear on the TV screen.

To check the remaining tape length of a T-140 or T-180 tape, set SELC. DE CINTA in the OPCIONES menu to 180. (Fo r details, see page 62.)

Press CH +/– to select the channel or line input video source you want to record.

Press SP/EP to select the tape speed, SP or EP. EP (Extended Play) provides recording time three times as long as SP

(Standard Play). However, SP produces better picture and audio quality.

Press z REC to start recording. The recording indicator l ights up red in the display window.

• CH

VIDEO

APC

SP / EP

VIDEO

APC

REC

VIDEO

APC

Recording indicator

SP 20:00:2

Time counter

Remaining tape length

1-9

Recording TV programs

To watch another TV program while recording

To save a recording

To prevent accidental erasure, break off the safety tab as illustrated. To record on the tape again, cover the tab hole with adhesive tape.

Tips

• To select a channel, you can use the number buttons on the remote commander. Enter the channel number, then press E NTER.

• You can select a video source from the LINE-1 IN or LINE-2 IN jacks using the INPUT SELECT button.

• The display appears on the TV screen indicating information about the tape, but the information won’t be recorded on the tape.

• If you don’t want to watch TV while recording, you can turn off the TV. When using a cable box, make sure to leave it on.

Notes

• The remaining tape length m ay not be indicated accurately for short tapes such as T-20 or T30, or tapes recorded in the LP mode.

• The display does not ap pear during still (pause) mode or slow-motion playback.

• It may take up to one minute for the VCR to calculate and display the remaining tape length

after you press DISPLAY.

Press TV/VIDEO to turn off the VIDEO indicator in the display window.

If the TV is connected to the VCR’s LINE OUT jacks, set the TV to the TV’s antenna input; if not, ski p this step.

Select another channel on the TV.

Safety tab

Recording TV programs using the Dial Timer

The Dial Timer function allows you to make timer recordings of programs without turning on your TV. Set the recording timer to record up to eight programs that will be broa dcast within a month using the DIAL TIMER. The recording start time and recording sto p time can be set at one minute intervals.

Before you start...

• When using a cable box, turn it on.

• Insert a tape with its safety tab in place.

Make sure the tape is longer than the total recording time.

Press DIAL TIMER. “DIA” and “HOY” appear alternately in the display window. If the date and time are not set, “DIA” flashes. See step 2 in the following

section “To set the clock” to set the date and time.

STOP

DIAL TIMER

?/1

POWER

CHANNEL +/–

123

456

789

INPUT SELECT

DIAL TIMER

VIDEO

APC

VIDEO

APC

Recording TV programs using the Dial Timer

Turn DIAL TIMER to set the recording date.

Press DIAL TIMER. “DESDE” and the current time appear alternately in the display window.

Turn DIAL TIMER to set the recording start time. You can set the recording start time in 15 minute intervals or adjust the time

in one minute intervals by pressing the CHANNEL +/– buttons.

Press DIAL TIMER. “HASTA” and the recording stop time appear alternately in the display

window.

DIAL TIMER

VIDEO

APC

DIAL TIMER

VIDEO

APC

VIDEO

APC

DIAL TIMER

CHANNEL

VIDEO

APC

DIAL TIMER

VIDEO

APC

VIDEO

APC

continued

Recording TV programs using the Dial Timer

To return to the previous step

To return to the previous step, press the CHANNEL + and – buttons on the VCR at the same time during any of the Dial Timer settings.

To stop recording

To stop the VCR while recording, press x STO P.

Turn DIAL TIMER to set the recording stop time. You can set the recording stop time in 15 minute intervals or adjust the time

in one minute intervals by pressing the CHANNEL +/– buttons.

Press DIAL TIMER. The channel number appears in t he display window.

Turn DIAL TIMER to set the channel number. To record from a source connected to the LINE-1 IN or LINE-2 IN jacks,

turn DIAL TIMER or press INPUT SELECT on the remote commander to display “L1” or “L2”.

Press DIAL TIMER to complete the setting. “OK” appears in the display window for about five seconds.

The indicator appears in the display window and the VCR stands by for recording. When using a cable box, leave it on.

DIAL TIMER

CHANNEL

VIDEO

APC

DIAL TIMER

VIDEO

APC

DIAL TIMER

INPUT

SELECT

VIDEO

APC

DIAL TIMER

1-10

Recording TV programs using the Dial Timer

To use the VCR after setting the timer

To use the VCR before a timer recording begins, just press ?/1. The indicator disappears from the display window and the VCR switches on. Remember to press ?/1 to reset the VCR to the timer recording standby mode after using the VCR.

You can also do the following tasks while the VCR is recording:

• Reset the counter (page 33).

• Display tape information on the TV screen (page 36).

• Check the timer settings (page 50).

• Watch another TV program (page 37).

To set the cloc k

Tips

• To cancel a Dial Timer setting, press

STOP on the VCR while you are making the setting.

• The program is recorded in the current tape speed. To change the tape speed, press SP/EP before you complete the sett ing in step 9 (page 40).

• When you are recording a program in the SP mode and the remaining tape becomes shorter than the recording time, the tape speed is automatically changed to the EP mode. Note that some noise will appear on the p icture when the tape speed is changed. I f you want to keep the tape speed, set VEL. AUTO. CINTA to NO in the OPCIONES menu (page 62).

• To check, change, or cancel the program setting, see “Checking/changing/cancelin g timer settings” (page 50).

Turn DIAL TIMER so that “RELOJ” appears in the display window.

Press DIAL TIMER. “DIA” appears in the display window.

Turn DIAL TIMER to set the day.

Press DIAL TIMER. “MES” appears in the display window.

Turn and press DIAL TIMER to set the month and then the year. After you set the year, “RELOJ” appears in the display window again.

Turn and press DIAL TIMER to set the hour and minut e.

When you have finished setting the time, press DIAL TIMER to start the clock.

continued

Recording TV programs using the Dial Timer

Notes

• If eight programs have already been set using the PROG./VERIF. menu, “LLENO” appears in the display window for about five seconds.

• If you set the clock using the Auto Clock Set function, the clock will adjust itself to the incoming time signal regardless of a djustments made with the Dial Timer. Be sure you have set ACS correctly.

• The

indicator flashes in the display window when yo u complete the setting in step 9

(page 40) with no tape inserted.

About the Demonstration Mode

The Dial Timer function has a Demonstration Mode t hat allows the user, such as a salesperson, to enter more than eight examples of timer settings when demonstrating the use of the Dial Timer. It cancels the LLENO notice which appears if eight programs have already been set. Do not use the Demonstration Mode for making timer recordings. Doing so may cause the settings to be inaccurat e.

To activate the Demonstration Mode

Press X PAUSE on the VCR

while turning the DIAL TIMER. “DEMO” appears in

the display window for a few seconds.

To cancel the Demonstration Mode

Turn the power off and unplug the AC power cord. Although the Demonstration Mode is canceled, the timer settings entered while using the Demonstration Mode will remain. Be sure to manually cancel the timer settings before you use the Dial Timer or any other timer method after reconnecting the AC power cord (see page 50).

Recording TV programs using the timer

You can preset up to eight programs together with the Dial Timer settings at a time.

Before you start…

• Check that the VCR clock is set to t he correct time.

• Turn on your TV and set it to the video channel. When using a cable box, turn it on.

• Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording time.

Press TIMER to display PROG./VERIF.

123

456

789

INPUT SELECT SP/EP

TIMER

CH +/–

M/m/</,

STOP

?/1

TIMER

VIE

–– –––: –––––––:– / ––– / ––– / ––– / ––– / ––– / ––– / ––– /

–––: –––––––

–

–––: ––––––:

–––: –––––––:

PROG. / VERIF.

VOLVER

MENUPARA SALIR :

AJUSTAR :

SELECCIONAR :

FECHA TER.COM.

CANCELAR :

CLEAR

9/28

continued

Recording TV programs using the timer

To stop recording

To stop the VCR while recording, press x STOP.

Daily/weekly recording

In step 3 above, press m to select the recording pattern. Each time you press m, the indication changes as shown below. Press M to change the indication in reverse order.

the current date t DOM-SAB t LUN-SAB t LUN-VIE t CADA SAB t ..... t

CADA LUN

CADA DOM t 1 month later t (dates count down) t the current

date

Press M/m to highlight the line that is to be set, then press OK.

Set the date, start and stop time, channel number, and tape speed:

1 Pr ess M/m to set each item.

2 Pr ess , to highlight and set each item

in turn.

To correct a setting, press < to return to that setting and reset.

To record the same program every day or the same day every week, press m while the date is highlighted. For details, see “Daily/weekly recording” below.

To record from a source connected to the LINE-1 IN or LINE-2 IN jacks, press INPUT SELECT or CH+/– to display “L1” or “L2” in the “CH” position.

Press OK to confirm the setting. To enter another setting, press M/m to highlight the next line and repeat step

Press TIMER.

Press ?/1 to turn off the VCR.

The indicator appears in the display window and the VCR stands by for recording.

When using a cable box, leave it on.

PLAY

INPUT

SELECT

• CH

VIE

DOM 8 0

PM PM

0:90053SP:

–––: –––––––: –––: –––––––:

–––: –––––––:

390/

––– / ––– / ––– / ––– / ––– / ––– / ––– /

FIN : OK

PROG. / VERIF.

VOLVER

PARA SALIR :

AJUSTAR :

SELECCIONAR :

9/28

FECHA TER.COM.

PLAY

TIMER

1-11

Recording TV programs using the timer

To use the VCR after setting the timer

To use the VCR before timer recording begins, just press ?/1. The indicator disappears from the display window and the VCR switches on. Remember to press ?/1 to reset the VCR to the timer recording standby mode after using the VCR.

You can also do the following tasks while the VCR is recording:

• Reset the counter (page 33).

• Display tape information on the TV screen (page 36).

• Check the timer settings (page 50).

• Watch another TV program (page 37).

Tips

• To set the channel, you can also use the CH+/– or number buttons.

• To show the PROG./VERIF. menu, you can also use the MENU button. Press MENU, then

press

M/m

to highlight PROG./VERIF. and press OK.

• To set the tape speed, you can also use the SP/EP button.

• When you are recording a program in the SP mode and the remaining tape becomes shorter

than the recording time, the tape speed is automatically changed to the EP mode. Note that some noise will appear on the p icture when the tape speed is changed. I f you want to keep the tape speed, set VEL. AUTO. CINTA to NO in the OPCIONES menu (page 62).

• To check, change or cancel the program setting, see “Checking/changing/canceling tim er settings” (page 50).

• If you want to return to the previous menu and continue with other o perations after setting the timer, press

to highlight VOLVER, then press OK. The display returns to the MENU screen. If you are finished using the VCR, turn off the power before time r recording starts.

Locking the VCR (Child Lock)

To lock the VCR

When the VCR is turned on, hold down ?/1 POWER on the VCR

until the indicator appears in the display window. The VCR turns off and the - indicator remains lit. The VCR will not work except for timer recordings.

To unlock the VCR

Hold down ?/1 POWER on the VCR

until the - indicator disappears from the

display window. The VCR is unlocked and turns on. To stop timer recording while the VCR is locked, press x STOP. The recording

stops and the VCR is unlocked.

Note

• The VCR will b e unlocked when:

– You stop timer recording by pressing

STOP.

– You insert a tape. – The AC power cord is disconnected or power supply stops.

After you have set the timer, you can lock all of the buttons on the VCR so that the settings are not canceled by mistake.

?/1

POWER

STOP

Playing/searching at various speeds

Additional Operations

Playing/searching at various speeds

To resume normal playback

Press H PLAY.

Playback options Operation

View the picture during fastforward or rewind

During fast-forward, hold down

M FF. During rewind, hold down

m REW.

Play at high speed • During playback, briefly press

M FF or m REW on the remote

commander. The tape continues to play at hi gh speed.

• During playback, ho ld down

M FF or m REW. When you

release the button, normal playback r esumes.

Play at twice the normal speed During p layback, press ×2.

Play in slow motion During playback or pause, press

y SLOW.

Play frame by frame During pause, press

M FF or m REW on the remote commande r.

Hold down the button to play one frame each second.

Rewind and start play While the tape is stopped, hold down

m REW on the VCR and press

H PLAY on the VCR.

y SLOW

m REW

H PLAY

m REW

M FF

TRACKING +/–

continued

Playing/searching at various speeds

Tip

• Adjust the picture using the TRACKING +/– buttons if:

– Streaks appear while playing in slow motion. – The picture shakes during pause. To set tracking to the center position, press both buttons (+/–) at the same time.

Notes

• The sound is muted d uring these operations.

• Tapes recorded in the LP mode on other VCRs can be played back on this VCR but the

picture quality cannot be guaranteed.

• The picture may sh ow noise when playing at high speed in reverse.

1-12

Setting the recording duration time

To extend the duration

Press z REC repeatedly to set a new duration time.

To cancel the duration

Press z REC repeated ly until the indicator disappears and the VCR returns to normal recording mode.

To stop while recording

Press x STOP.

Note

• You cannot display the current tape time in the display window when setting the recording duration time.

After you have started recording, you can have the VCR stop recording automatically after a specified duration.

While recording, press z REC.

The indicator appears in the display window.

Press z RE C repeatedly to set the duration time. Each press advances the time in increments of 30 minutes.

The tape counter decreases minute by minute to 0:00, then the VCR stops recording and turns off automatically.

REC

VIDEO

APC

0:30 1:00

5:30 6:00

Normal recording

Checking/changing/canceling timer settings

Before you start…

• Turn on your TV and set it to the video channel.

Press ?/1 to turn on the VCR.

Press TIMER to display PROG./VERIF.

• If you want to change a setting, go on to the next st ep.

• If you do not need to change the settings, pres s MENU, then turn off the VCR

to return to recording standby.

123

456

789

?/1

M/m/</,

CLEAR

TIMER

Checking/changing/canceling timer settings

When the timer settings overlap

The program that starts first has priority and the second program starts recording only after the first program has finished. If the programs start at the same time, the program listed first in the menu has priority.

Tip

• To show the PROG./VERIF. menu, you can also use the MENU button. Press MENU, then press

M/m

to highlight PROG./VERIF. and press OK.

Press M/m to highlight the setting you want to change or cancel.

• To change the setting, press OK and press </ , to highlight the item you want to change, then press M/m to reset it.

• To cancel the setting, press CLEAR.

Press OK.

Press MENU to exit the menu. If any timer settings remain, turn off the VCR to return to recording standby.

PROG. / VERIF.

DOM 8 0

PM PM

0:90053SP:/

–––––: –––––––:–/ –––––: –––––––:–/

–––––: –––––––:–/

CADA 6 03:70024EP:

LUN –

MER

VIE 2 00:30006EP:

20101

0:10302EP:10MAR/

VOLVER

MENUPARA SALIR :

AJUSTAR :

SELECCIONAR :

OK CANCELAR : CLEAR

039

9/28 VIE

FECHA TER.COM.

Will be cut off

Program 1

Program 2

Recording stereo and bilingual programs (SLV-LX70S and LX60S only)

Recording stereo programs

This VCR automatically receives and records stereo programs. When a ster eo program is received, the STEREO indi cator lights up. If there is noise in the stereo program, set ESTEREO AUTO. in the OPCIONES menu to NO. The sound will be recorded in monaural (on b oth hi-fi and normal audio tracks) but with less noise. For details, see page 62.

Recording bilingual programs

Normally, this VCR records only the main sound. When a SAP (S econd Audio Program) is received, the SAP indicator lights up. To record only SAP sound, set SINTONIZ. AUDIO in the OPCIONES menu to SAP. Fo r details, see page 62.

Selecting the sound during playback

Press AUDIO MONITOR to select the sound you want.

To listen to On-screen display Display window

Stereo ESTEREO STEREO

Left channel L STEREO

Right channel R STEREO

Monaural sound on the normal audio track

No indicator No indicator

1-13

Recording stereo and bilingual programs (SLV-LX70S and LX60S only)

How sound is recorded on a video tape

The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the main track along with th e picture. Monaural sound is recorde d onto the normal audio track along the edge of the tape.

Notes

• To play a tape in stereo, you must u se the A/V connections.

• When you play a tape recorded in m onaural, the sound is heard in monaural regardless of the

AUDIO MONITOR setting.

Normal audio track

Hi-fi audio track (main track)

Monaural sound

Stereo sound (left/right channels)

Searching for the beginning of a timer recorded program

Press DIAL TIMER. The VCR turns on, rewinds to the beginning of the most recently recorded program

and starts playback automatically. The SEARCH MODE button turns off.

Tip

• To turn off the SEARCH MODE button, first turn the VCR on, then press the SEARCH MODE button. (Do not press any other button at this point, otherwise this SEARCH MODE function will be canceled.) To start the SEARCH MODE function, press the SEARCH MODE button once. If you press the SEARCH MODE button repeatedly, you can enter the index search or Time Search mode (for details, see page 55 an d 56).

Notes

• This SEARCH MODE function will be canceled (the SEARCH M ODE button turns off) if:

– The VCR starts recording other programs. – You press

PLAY, M FF, m REW, or AEJECT button while the VCR is on.

– If there is a power failure.

If you record a program using the timer function, you can easily find the beginning of the recording with this SEARCH MODE function. The SEARCH MODE button lights up when the VCR finishes a timer recording and the display window shows the following:

SEARCH MODE

DIAL TIMER

Searching using the index function

To stop searching

Press x STOP.

Note

• No index signal will be added when recording start s from recording pause. However, an index signal will be marked if you change the channel during recording pause.

The VCR marks the tape with an index signal at the point where each recording begins. Use these signals as references to find a specific recording. The VCR can search up to 9 index signals ahead of or behind the current position.

Press SEARCH MODE on the VCR repeatedly until “INDEX” appears in the display window (the SEARCH MODE button lights up).

Turn DIAL TIMER to specify how many index signals ahead or behind you want to search:

• To search ahead, turn DIAL TIMER clockwise.

• To search backwards, turn DIAL TIMER counterclockwise.

Press DIAL TIMER. The VCR starts searching. The playback starts (the SEARCH MODE button

turns off) from the point about five seconds ahead of the specified index mark.

SEARCH MODE

DIAL TIMER

APC

Searching using the Time Search function

To stop searching

Press x STO P.

Tip

• The VCR can search up to six hours ahead of or behind the current position of a tape.

You can easily find a specific point on a tape by using the Time Search function. For example, you can find a recorded portion 15 minutes ahead of or behind the current position of a tape by using the Time Search function.

Press SEARCH MODE repeatedly until “TIME” appears in the display window (the SEARCH MODE button lights up).

Turn DIAL TIMER clockwise or counterclockwise to set the length of the time portion you want the VCR to fast-forward or rewind the tape. Each turn on the control increases or decreases the d uration by 15 minutes.

For example, if you want to watch a recorded portion 15 minutes ahead of the current position, turn DIAL TIMER once clockwise.

To change the time by one minute, press CHANNEL +/–.

Press DIAL TIMER. The VCR starts searching and the tape counter starts counting until it reaches the

specified point.

The VCR starts playback automatically when the tape counter reaches the specified point (the SEARCH MODE button turns off).

SEARCH MODE

DIAL TIMER

APC

1-14

Searching using the index function

To stop searching

Press x STOP.

Note

• No index signal will be added when recording starts from recording pause. However, an index signal will be marked if you change the channel during recording pause.

Press SEARCH MODE on the VCR repeatedly until “INDEX” appears in the display window (the SEARCH MODE button lights up).

Turn DIAL TIMER to specify how many index signals ahead or behind you want to search:

• To search ahead, turn DIAL TIMER clockwise.

• To search backwards, turn DIAL TIMER counterclockwise.

Press DIAL TIMER. The VCR starts searching. The playback starts (the SEARCH MODE button

turns off) from the point about five seconds ahead of the specified index mark.

SEARCH MODE

DIAL TIMER

APC

Searching using the Time Search function

To stop searching

Press x STO P.

Tip

• The VCR can search up to six hours ahead of or behind the current position of a tape.

Press SEARCH MODE repeatedly until “TIME” appears in the display window (the SEARCH MODE button lights up).

For example, if you want to watch a recorded portion 15 minutes ahead of the current position, turn DIAL TIMER once clockwise.

To change the time by one minute, press CHANNEL +/–.

Press DIAL TIMER. The VCR starts searching and the tape counter starts counting until it reaches the

specified point.

The VCR starts playback automatically when the tape counter reaches the specified point (the SEARCH MODE button turns off).

SEARCH MODE

DIAL TIMER

APC

Skip-searching automatically (Quick View)

Hold down M FF (or m REW) more than two seconds during stop. “SKIP” indicator appears on the TV screen.

The VCR searches forward (or backward) for about two minutes on the counter while showing the contents of the tape. Then it fast-forwards (or rewinds) for about ten minutes on the counter. The VCR repeats this operation until it stops at the end (or beginning) of the tape.

To cancel skip-search

Press H PLAY or x STOP.

Note

• The VCR automatically fast-for wards (or rewinds) any portion with no recording.

You can spot check an entire tape quickly using the Quick View function. At intervals, the VCR skips playback while searching forward or backward.

REW

SKIP

search forward while showing the tape contents

fast-forward

Searching for a selected point on the tape

You can easily find a specific point by moving the pointer on th e TV screen.

The VCR fast-forwards or rewinds to the point you indicate and starts playback automatically.

Press DISPLAY repeatedly until the bar indication appears on the TV screen.

A cursor (x) indicating the current p osition of the tape appears on th e bar indication. If the cursor does not appear, play the tape a few moments (by pressing H PLAY, M FF, or m REW) until the cursor appears.

Press </, to move the pointer (V) to the point where you want to start playback.

The VCR starts searching and the cursor (x) moves toward the pointer. When the VCR locates the marked point, playback starts.

123

456

789

DISPLAY

</,

0 120

1-15

Searching for a selected point on the tape

To cancel searching

Press H PLAY or x STOP.

To turn off the bar indication

Press DISPLAY again.

Notes

• The figure on the bar indi cation represents the total time length of the inserted tape as shown below. The total time length may n ot be displayed correctly for:

– Tapes other than T-60, T-120, or T-160. – Tapes recorded in more than one tape speed mode.

• If you move the pointer (

) on the bar indication while searching, the VCR searches for the

new reset point.

• With the bar indication on, the

FF/ , and m REW/ < buttons on the remote commander work only for moving the po inter (V) and are not used for normal tape operat ion. The

FF and m REW buttons on the VCR are used for norm al tape operation. Note,

however, if you press these buttons on the VCR

, searching is canceled.

Tape type

Total time length

SP LP EP

T-60 or shorter 60 120 180

from T-80 to T-140 120 240 360

T-160 or longer 160 320 480

Adjusting the picture

Adjusting the tracking

Although the VCR automatically ad justs the tracking when playing a tape (the indicator flashes in the display window, then turns off), distortion may occur if the recording is in poor condition. In this case, manually adjust the tracking.

Press TRACKING +/– to display the tracking meter. The distortion should disappear as you press one of the two tracking buttons (the indicator lights up). To resume automatic tracking adjustment, eject the tape and reinsert it.

About the Reality Regenerator function

The Reality Regenerator function automatically restores the picture to its original quality during playback.

To use the Reality Regenerator function

To turn it off, select NO in step 4. The RR indicator turns off in the display window.

Press MENU, then select OPCIONES and press OK.

Press M/m to highlight PRÓXIMA, then press OK.

Press M/m to highlight REALITY REGENERATOR on PÁGINA2 of the OPCIONES menu, then press OK.

Press M/m to set REALITY REGENERATOR to SI, then press OK. The RR indicator lights up in the display window.

Press MENU to return to the original screen.

SEGUIMIENTO NORMAL

Tracking meter

OPCIONES

REALITY REGENERATOR

APC

SENSR CONDCIÓN CABEZA NITIDEZ

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

2PÁGINA

Adjusting the picture

About the Adaptive Picture Control (APC) function

The Adaptive Picture Control (APC) function automatically improves recording and playback quality by adjusting the VCR to the condition of the video heads and tape. To maintain better picture quality, we recommend that you set APC to SI on PÁGINA2 of the OPCIONES menu (The APC indicator lights up in the display window). For details, see page 63.

APC playback

The APC function automatically works on all types of tapes, including rental tapes and tapes that were not recorded with APC.

APC recording

Whenever you insert a tape and first start recording, the VCR adjusts to the tape using the APC function (the APC indicator flashes rapidly). This adjustment is retained until the tape is ejected.

Notes

• The auto tracking adj ustment cannot be guaranteed to work with tapes recorded in the LP mode on other VCRs.

• The APC func tion does not work if the tape speed is automatically changed from the SP to EP mode during a timer recording when VEL. AUTO. CINTA is set to SI in the OPCIONES menu, unless the tape has been recorded in the EP mode with the APC function.

• There is a delay of about ten seconds before the VCR actually starts recording while the VCR analyzes the tape. To avoid the delay, first set the VCR to recording pause (the APC indicator flashes slowly) and press

z REC to have the VCR analyze the tape (the APC indicator

flashes rapidly) and return to recording p ause. After the APC indicator stops flashing, press

X PAUSE to start recording immediately.

If you want to start recording quickly without using the APC function, first set the VCR to recording pause (the APC indicato r flashes slowly) and press

X PAUSE again to start

recording.

Changing menu options

Menu choices

Initial settings are indicated in bold print.

PÁGINA1

Press MENU, then select OPCIONES and press OK.

Press M/m to highlight the option to change, then press OK. To g o to PÁGINA2, highlight PRÓXIMA and press OK. To return to PÁGINA1,

highlight ANTERIOR and press OK.

Press M/m to change the setting, then press OK. To adjust the sharpness, press </, and press OK.

Press MENU to return to the original screen.

Menu option Set this option to

SELEC. AUTO. ANT. • SI if you r TV is connected only to VHF/UHF OUT on the

VCR. To play a tape, set the TV to the VCR channel (channel 3 or 4).

• NO if your TV is connected to both VHF/UHF OUT and LINE OUT on the VCR. To play a tape, set the TV to the VCR input.

ESTEREO AUTO. (SLV-LX70S and LX60S only)

• SI to receive stereo programs.

• NO to reduce noise. The sou nd changes to monaural.

SINTONIZ. AUDIO (SLV-LX70S and LX60S only)

• MAIN to record the main sound on both hi-fi and norma l audio tracks.

• SAP to record the SAP (Second Audio Program) sound on both hi-fi and normal audio tracks.

SELC. DE CINTA • AU TO when using a T-160 length tape or any tape shorter than

a T-140 length tape.

• 180 when using a T-140 or T-180 length tape.

For details, see page 36.

VEL. AUTO. CINTA • SI to change the time r recording tape speed automatically to

the EP mode when the remaining ta pe length becomes shorter than the recording time. To operate VEL. AUTO. CINTA, set SELC. DE CINTA correctly.

• NO to keep the same tape speed.

OPCIONES

ESTEREO AUTO.

SELEC. AUTO. ANT.

SINTONIZ. AUDIO SELC. DE CINTA

SI MAIN

AUTO

VEL. AUTO. CINTA

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

1PÁGINA

OPCIONES

REALITY REGENERATOR

APC

SENSR CONDCIÓN CABEZA NITIDEZ

SI SI

VOLVER

AJUSTAR :

SELECCIONAR :

OK MENUPARA SALIR :

2PÁGINA

1-16

Changing menu options

PÁGINA2

Menu option Set this option to

APC • SI to switch on the APC (Adapt ive Picture Control) function

and improve picture quality.

• NO to switch off APC.

REALITY REGENERATOR

• SI to switch on the Real ity Regenerator (Reality Regenerator)

function and restore the picture to its original quality during playback.

• NO to switch off Reality Regenerator.

SENSR CONDCIÓN CABEZA

• SI to allow the VCR to automatically check the condition of

the video heads and inf orm you when they are dirty.

• NO to turn off the sensor.

NITIDEZ • B (Low) through A (High) to adjust the sharpne ss of the

picture. Select B to turn off the sharpness control.

Editing with another VCR

How to connect to record on this VCR

SLV-LX70S and LX60S

SLV-LX50 and LX40

This VCR (Recorder)

Other VCR (P layer)

LINE OUT

: Signal flow

LINE-2 IN

Audio/video cable (not supplied)

This VCR (Recorder)

Other VCR (P layer)

LINE OUT

: Signal flow

LINE-2 IN

Audio/video cable (not supplied)

Editing with another VCR

Notes

• Make sure you connect the plugs to jacks of the same color.

• If you connected this VCR to both the LINE IN and LINE OUT jacks of the other VCR,

select the input correctly t o prevent a humming noise.

• You can use the LINE-1 IN jacks for ed iting.

• If the other VCR is a mona ural type and connected to this VCR’s LINE-2 IN jacks, connec t

the audio plug to the AUDIO L (white) jack. The sound is recorded on both right and left channels. If you connect to the AUDIO R (red) ja ck, the sound is recorded only on the right channel. (SLV-LX70S and LX60S only)

• If the other VCR is a monaural type and connected to this VC R’s LINE-1 IN jacks, the sound is recorded only on the channel whose jack is connected t o the audio plug. To record on both right and left channels, connect the audio plugs to the AUDIO R/L jacks using a VMC910HG audio/video cable (not supplied). (SLV-LX70S and LX60S only)

continued

Editing with another VCR

Operation (when recording on this VCR)

To stop editing

Press the x STOP buttons on both VCRs.

Tip

• To cut out unwanted scenes while editing, press

X PAUSE on this VCR when an unwanted

scene begins. When it ends, press

X PAUSE again to resume recording.

Note

• If you start recording following the procedure above, the VCR won’t start recording with the APC function. To record a tape with th e APC function, press

z REC again during recording

pause in step 3 so that the VCR analyzes the tape. Then, press

X PAUSE after the APC

indicator stops flashing to start recording. If you press

X PAU SE be for e the APC indicator

stops flashing, the APC function is canceled.

Before you start editing

• Turn on your TV and set it to the video channel.

• Press INPUT SELECT or CHANNEL +/– to display “L2” (or

“L1”) in the display window.

• Press SP/EP to select the tape speed,

SP or EP.

Insert a source tape with its safety tab removed into the other (playback) VCR. Search for the point to start playback and set it to playbac k pause.

Insert a tape into this (recording) VCR. Search for the point to start recording and press X PAU SE .

Press z REC o n this VCR to set it to recording pause.

To start editing, press the X PAUSE buttons on both VCRs at the same tim e.

z REC

X PA US E

1-17

General setup information

Additional Information

General setup information

Setting the RF unit

When connecting the VCR to the TV using only the antenna cable, you must set the RF UNIT switch on the rear of the VCR so that the TV can receive the correct signal from the VCR.

Set the RF UNIT switch on the rear of the VCR to CH3 or CH4, whichever channel is not used in your area. If b oth are used, set the switch to either channel.

Press ?/1 POWER to turn on the VCR.

Press TV/VIDEO to turn on the VIDEO indicator in the VCR’s display window.

Press CHANNEL +/– to display a channel number in the display window. Select an active channel number in your area.

Turn on your TV and set it to the chan nel you selected in step 1 (channel 3 or 4). The channel you selected in step 4 app ears on the TV screen. If the channels

change when you press CHANNEL +/–, you have made the correct setting. Whenever you use the VCR, set the TV to the channel selected in step 1.

CH3

RF UNIT

CH4

CHANNEL +/–

?/1

POWER

123

456

789

TV/VIDEO

continued

General setup information

Attaching the external antenna connector

Attaching a UHF/VHF band mixer

When using a 300-ohm twin lead cable for a VHF/UHF antenna, use the EAC-32 antenna connector (not supplied) to connect the antenna to the VCR.

Loosen the screws on the antenna connector.

Wind the twin leads around the screws on the antenna connector.

Retighten the screws.

When using both a 75-ohm coaxial cabl e and a 300-ohm twin lead cable for a VHF/UHF antenna, use the EAC-66 UHF/VHF band separator/mixer (not supplied) to connect the antenna to the VCR.

Loosen the screws on the mixer.

Wind the twin leads around the screws on the mixer.

Retighten the screws.

Connect the 75-ohm coaxial cable to the mixer.

300-ohm twin lead cable

EAC-32 antenna connector (not supplied)

300-ohm twin lead cable

EAC-66 UHF/VHF band separator/ mixer (not supplied)

75-ohm coaxial cable

Troubleshooting

Head Condition Sens or

The Head Condition Sensor checks the video heads’ condition. If the heads are dirty, a message will instruct you to insert a vide o head cleaning cassette.

Be sure to use the Sony T-25CLD or T-25CLDR video head cleaning cassette. If these cleaning cassettes are not available in your area, have the heads cleaned at your nearest Sony service facility (a standard service charge will be required).

Note

• SENSR CONDCIÓN CABEZA in OPCIONES must be set to SI for the Head Condition Sensor to operate.

• To turn off the head condition sensor message, set SENSR CONDCIÓN CABEZA to NO.

Symptoms caused by contaminated video heads

• Normal picture • Unclear picture• Rough picture

initial

contamination

terminal

• No picture (or black & white screen appears)

Index to parts and controls

Refer to the pages indicated in parentheses ( ) for details.

Front panel

SLV-LX70S and LX60S

A ?/1 POWER switch (44)

B Z EJECT button (33)

C Tape compartment

D Remote sensor (5)

E m REW (rewind) button (33) (47)

F H PLAY button (33) (47)

G M FF (fast-forward) button (33) (47)

H z REC (record ) button (36) (49) (66)

I x STOP button (33) (66)

J X PAUSE button (33) (66)

K DIAL TIMER (38) (54) (55) (56)

L SEARCH MODE button (54) (55) (56)

M CHANNEL/TRACKING +/– buttons

(36) (60)

N EASY SET UP button (11) (13) (16)

O LINE-2 IN VIDEO/AUDIO L/R jacks

(64)

continued

1-18

Index to parts and controls

SLV-LX50 and LX40

A ?/1 POWER switch (44)

B Z EJECT button (33)

C Tape compartment

D Remote sensor (5)

E m REW (rewind) button (33) (47)

F H PLAY button (33) (47)

G M FF (fast-forward) button (33) (47)

H z REC (record) button (36) (49) (66)

I x STOP button (33) (66)

J X PAUSE button (33) (66)

K DIAL TIMER (38) (54) (55) (56)

L SEARCH MODE button (54) (55) (56)

M CHANNEL/TRACKING +/– buttons

(36) (60)

N EASY SET UP button (11) (13) (16)

O LINE-2 IN VIDEO/AUDIO jacks (64)

Index to parts and controls

Display window

A Timer indicator (40) (44)

B SAP (Second Audio P rogram) indicator

(52) (SLV-LX70S and LX60S only)

C STEREO indicator (52) (SLV-LX70S

and LX60S only)

D Tape speed indicator (36)

E VIDEO indicator (37) (67)

F APC (Adaptive Picture Control)

indicator (61)

G RR (Reality Regenerator) indicator (60)

H Tracking indicato r (60)

I Child lock indicator (46)

J Time counter/clock/line/channel

indicator (33) (36) (66)

K Tape/recording indicator (36)

STEREO SAP LP SP

VIDEO

APC

continued

Index to parts and controls

Rear panel

SLV-LX70S and LX60S

A AC power cord (7)

B LINE-1 IN AUDIO R/L/VIDEO jacks

(65)

C RF (Radio Frequ ency) UNIT switch (67)

D VHF/UHF IN connector (10) (12) (15)

E VHF/UHF OUT connector (10) (12) (15)

F LINE OUT AUDIO R/L/VIDEO jacks

(8)

SLV-LX50 and LX40

A AC power cord (7)

B LINE-1 IN AUDIO/VIDEO jacks (65)

C RF (Radio Frequ ency) UNIT switch (67)

D VHF/UHF IN connector (10) (12) (15)

E VHF/UHF OUT connector (10) (12) (15)

F LINE OUT AUDIO/VIDEO jacks (9)

Index to parts and controls

Remote commander

A •TV

/ VIDEO switch (5)

B Z EJECT button (33)

C TRINITRON TV SYNCHRO PLAY

button (34)

D DISPLAY button (36) (58)

E VOL (volume) +/– buttons (6)

F INPUT SELECT button (37) (66)

G z REC (record) button (36) (49)

H SP (Standar d Play)/EP (Extended Play)

button (36)

I MENU button (18) (62)

J X PAU SE /M button (18) (33)

x STOP /m button (18) (33) m REW (rewind)/ < button (33) (47) M FF (fast-forward)/ , button (33)

(47) H PLAY/OK button (18) (33)

123

456

789

continued

+ 49 hidden pages

Sony RMT-V293A, RMT-V294A, SLV-LX40, SLV-LX50, SLV-LX50CL Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual