Sony SDM-E76A, SDM-E76D, SDM-E96A, SDM-E96D Service Manual

Service Manual
SDM-E76A: AEP, U/C, CH SDM-E76D: AEP, U/C, CH, WB SDM-E96A: AEP, U/C, CH SDM-E96D: AEP, U/C, CH, WB
CONTENTS
PRECAUTIONS 3 SPECIFICATIONS 4 TIMING CHART 5 SIGNAL CONNECTOR PIN 6 EDID data for SDM-E76x 7, 8 EDID data for SDM-E96x 9, 10 OPERATING INSTRUCTIONS 11 SERVICE MODE 12 WIRING DIAGRAM 13 DISASSEMBLY PROCESS 14, 15 ADJUSTMENT 16 SERIAL NUMBER LIST 17 EXPLODED VIEW 18 REPLACEMENT PARTS LIST 19, 20
Page
2 SDM-E76A,D / SDM-E96A,D(E)
PRECAUTION
WARNING FOR THE SAFETY-RELATED COMPONENT.
• There are some special components used in LCD monitor that are important for safety.
These parts are marked on the schematic diagram and the replacement parts list.
It is essential that these critical parts should be replaced with the manufacturer’s specified parts to prevent electric shock, fire or other hazard.
• Do not modify original design without obtaining written permission from manufacturer or you will void the original parts and labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE WITH BACKLIGHT UNIT.
• Must mount the module using mounting holes arranged in four corners.
• Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the screen.
• Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in damage to the panel.
• Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
• Make certain that treatment person’s bodies are grounded through wrist band.
• Do not leave the module in high temperature and in areas of high humidity for a long time.
• The module not is exposed to the direct sunlight.
• Avoid contact with water as it may a short circuit within the module.
• If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may damage the panel.)
• If you want to replace with the new backlight (CCFL) or inverter circuit, must disconnect the AC adapter because high voltage appears at inverter circuit about 650Vrms.
• Handle with care wires or connectors of the inverter circuit. If the wires are pressed cause short and may burn or take fire.
Leakage Current Hot Check Circuit
3 SDM-E76A,D / SDM-E96A,D(E)
SPECIFICATIONS
1. LCD CHARACTERISTICS
Type : TFT Color LCD Module Active Display Area : 17 inch - SDM-E76A/D
: 19 inch - SDM-E96A/D
Pixel Pitch : 0.264 (H) x 0.264 (V) -SDM-E76A/D
: 0.294 (H) x 0.294 (V) -SDM-E96A/D
Size : 358.5(W) x 296.5(H) x 17.5(D)
- SDM-E76A/D
: 396(W) x 324(H) x 17.5(D)
- SDM-E96A/D
Color Depth : 16.2M colors - SDM-E76A/D
: 16.2M colors - SDM-E96A/D Electrical Interface : LVDS Surface Treatment : Anti Glare, Hard-coating (3H) Operating Mode : Normally White Backlight Unit : Top/Bottom edge side 4-CCFL
(Cold Cathode Fluorescent Lamp)
2. OPTICAL CHARACTERISTICS 2-1. Viewing Angle by Contrast Ratio > 10
SDM-E76A/D
Left : 70°(Typ) Right : 70°(Typ) Top : 70°(Typ) Bottom : 60°(Typ)
SDM-E96A/D
Left : -65° min., -70°(Typ) Right : +65° min., +70°(Typ) Top :+70° min., +75°(Typ) Bottom : -55°min., -60°(Typ)
2-2. Luminance :
300(Typ) - SDM-E76A/D
300(Typ) - SDM-E96A/D
2-3. Contrast Ratio :
500:1 (Typ) - SDM-E76A/D 700:1 (Typ) - SDM-E96A/D
3. SIGNAL (Refer to the Timing Chart)
3-1. Sync Signal
Type : Separate Sync, Composite Sync, SOG (Sync On Green), Digital
3-2. Video Input Signal
1) Type: R, G, B Analog
2) Voltage Level: 0~0.71 V a) Color 0, 0: 0 Vp-p b) Color 7, 0: 0.467 Vp-p c) Color 15, 0: 0.714 Vp-p
3) Input Impedance : 75
3-3. Operating Frequency
Analog Digital Horizontal: 28 ~ 80kHz 28 ~ 64kHz Vertical: 56 ~ 75Hz 60Hz Dot Clock:
< 135MHz < 108MHz
4. Max. Resolution
Analog : 1280 x 1024 / 75Hz Digital : 1280 x 1024 / 60Hz
5. POWER SUPPLY
5-1. Power: AC 100~240V, 50/60Hz, 5-2. Power Consumption SDM-E76A/D Normal operation < 38W Active off (deep sleep) < 1W Power off < 1W SDM-E96A/D Normal operation < 44W Active off (deep sleep) < 1W Power off < 1W
6. ENVIRONMENT
6-1. Operating Temperature:
5°C~35°C (41°F~95°F)
6-2. Relative Humidity:
10%~80% (Non-condensing)
7. DIMENSIONS SDM-E76A/D
Width: 382 mm (15.1'') Depth: 193.2 mm (7.6'') Height: 403.2 mm (15.9'')
SDM-E96A/D
Width: 420 mm (16.6'') Depth: 193.2 mm (7.6'') Height: 433.1 mm (17.1”)
8. WEIGHT SDM-E76A/D
Net. Weight: 4.5 kg (9.9 lbs) Gross Weight: 5.6 kg (12.31 lbs)
SDM-E96A/D
Net. Weight : 5.5kg (12.1 lbs) Gross Weight: 7.2kg (15.9 lbs)
4 SDM-E76A,D / SDM-E96A,D(E)
TIMING CHART
5 SDM-E76A,D / SDM-E96A,D(E)
SIGNAL CONNECTOR PIN
6 SDM-E76A,D / SDM-E96A,D(E)
Loading...
+ 14 hidden pages