Sony SAWMSP-69, SAWNSP-69 Service manual

SA-WMSP69
SERVICE MANUAL
Ver. 1.0 2005.05
• SA-WMSP69 is the subwoofer section in HT-6900DP/9900M.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6 ohm loads, from 28 – 200 Hz; rated 120 watts, minimum RMS power, with no more than
0.8% total harmonic distortion from 250 milliwatts to rated output.
US Model
Speaker system Active subwoofer,
Speaker unit 250 mm cone type Enclosure type Acoustically loaded bass
RMS output 160 W (6 ohms, 100 Hz,
Input LINE IN (input pin jacks)
Power requirements 120 V AC, 60 Hz Power consumption 120 W Dimensions (w/h/d) (Approx.)
Mass (Approx.) 13.0 kg (28 lb 11 oz)
Design and specifications are subject to change without notice.
magnetically shielded
reflex
THD 10%)
337 × 410 × 366 mm (13 1/4 × 16 1/8 × 14 1/2 inches) including front panel
9-879-650-01
2005E04-1 © 2005.05
SUB WOOFER
Sony Corporation
Audio Group Published by Sony Engineering Corporation
SA-WMSP69
r
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica­tion is 0.75 V, so analog meters must have an accurate low­voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set

TABLE OF CONTENTS

1. DIAGRAMS
1-1. Circuit Boards Location .................................................. 3
1-2. Schematic Diagram – Main Section – ............................. 5
1-3. Printed Wiring Boards – Main Section – ......................... 6
2. EXPLODED VIEWS
2-1. Front Section ................................................................... 7
2-2. Rear Section .................................................................... 8
3. ELECTRICAL PARTS LIST .................................. 9
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead­free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
0.15 µF
1.5 k
Earth Ground
(Fig. A)
AC
voltmete (0.75 V)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
1-1. CIRCUIT BOARDS LOCATION
SA-WMSP69
SECTION 1

DIAGRAMS

CONTROL board
MAIN board
INPUT board
POWER TRANS board
SWITCH board
3
SA-WMSP69
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
For schematic diagrams: Note:
• All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums.
• All resistors are in and 1/ specified.
C : panel designation.
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety. Replace only with part number specified.
A : B+ Line.
B : B– Line.
•Voltages are dc with respect to ground under no-signal (detuned) conditions.
no mark : Power on
•Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances.
• Signal path. F : AUDIO
4
W or less unless otherwise
For printed wiring boards: Note:
X : parts extracted from the component side.
Y : parts extracted from the conductor side.
•: Pattern from the side which enables seeing.
4
Loading...
+ 8 hidden pages