Sony RDR-HXD860 User Manual

2-886-042-11(1)

DVD Recorder

Operating Instructions

To find out useful hints, tips and information about Sony products and services please visit: www.sony-europe.com/myproduct

RDR-HXD860

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer serv icing to qualified personnel only. The mains lead must be changed only at a qualified service shop.

This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the laser protective housing inside the enclosure.

CAUTION

The use of optical instruments with this product will increase eye hazard. As the laser beam used in this DVD recorder is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only.

Notice for customers in the United Kingdom and Republic of Ireland

A molded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS1362, (i.e., marked with

or mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

Precautions

• This unit operates on 220 –

240 V AC, 50/60 Hz. Check that the unit’s operating voltage is identical with your local power supply.

• To prevent fire or shock hazard,

do not place objects filled with liquids, such as vases, on the apparatus.

• Install this system so that the

mains lead can be unplugged from the wall socket immediately in the event of trouble.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring th is product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

This label is located on the laser protective housing inside the enclosure.

Precautions

This equipment has been tested and found to comply with the limits set out in the EMC Directive using a connection cable shorter than 3 metres.

On safety

Should any solid object or liquid fall into the cabinet, unplug the recorder and have it checked by qualified personnel before operating it any further.

About the hard disk drive

The hard disk has a high storage density, which enables long recording durations and quick access to the written data. However, it can easily be damaged by shock, vibration or dust, and should be kept away from magnets. To avoid losing important data, observe the following precautions.

• Do not apply a strong shock to the recorder.

• Do not place the recorder in a location subject to mechanical vibrations or in an unstable location.

• Do not place the recorder on top of a hot surface, such as a VCR or amplifier (receiver).

• Do not use the recorder in a place subject to extreme changes in temperature (temperature gradient less than 10 °C/hour).

• Do not move the recorder with its mains lead connected.

• Do not disconnect the mains lead while the power is on.

• When disconnecting the mains lead, turn off the power and make sure that the hard disk drive is not operating (the clock is displayed in the front panel display for at least 30 seconds and all recording or dubbing has stopped).

• Do not move the recorder for one minute after you have unplugged the mains lead.

• Do not attempt to replace or upgrade the hard disk by yourself, as this may result in malfunction.

If the hard disk drive should malfunction, you ca nnot recover lost data. The hard disk drive is only a temporary storage space.

About repairing the hard disk drive

• The contents of the hard disk drive may be checked in case of repair or inspection du ring a malfunction or modification. However, the contents will not be backed up or saved by Sony.

• If the hard disk needs to be formatted or replaced, it will be done at the discretion of Sony. All contents of the hard disk drive will be erased, including contents that violate copyright laws.

On power sources

• The recorder is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the recorder itself has been turned off.

• If you are not going to use the recorder for a long time, be sure to disconnect th e recorder from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord.

On placement

• Place the recorder in a location with adequate ventilation to prevent heat build-up in the recorder.

• Do not place the recorder on a soft surface such as a rug that might block the ventilation holes.

• Do not place the recorder in a confined space such as a bookshelf or similar unit.

• Do not place the recorder in a location near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock.

• Do not place the recorder in an inclined position. It is designed to be operated in a horizontal position only.

• Keep the recorder and discs away from equipment with strong magnets, such as microwave ovens, or large loudspeakers.

• Do not place heavy objects on the recorder.

On recording

Make trial recordings before making the actual recording.

On compensation for lost recordings

Sony is not liable and will not compensate for any lost recordings or relevant losses, including when recordings are not made due to reasons including recorder failure, or when the contents of a recording are lost or damaged as a result of recorder failure or repair undertaken to the recorder. Sony will not restore, recover, or replicate the recorded contents under any circumstances.

,continued

Copyrights

• Television programmes, films, video tapes, discs, and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.

• This product incorporates copyright protection technology that is pr otected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Copy guard function

Since the recorder has a copy guard function, programmes received through an external tuner (not supplied) may contain copy protection signals (copy guard function) and as such may not be recordable, depending on the type of signal.

About this manual

• In this manual, the internal hard disk drive is written as “HDD,” and “disc” is used as a general reference for the HDD, DVDs, or CDs unless otherwise specified by the text or illustrations.

• Icons, such as , listed at the top of each explanation indicate what kind of media can be used with the function being explained.

• Instructions in this manual describe the controls on the remote. You can also use the controls on the recorder if they have the same or similar names as those on the remote.

• The on-screen display illustrations used in this manual may not match the graphics displayed on your TV screen.

• The explanations regarding DVDs in this manual refer to DVDs created on this recorder. The explanations do not apply to DVDs that are created on other recorders and played back on this recorder.

DVD

IMPORTANT NOTICE

Caution: This recorder is capable of holding a still video image or on-screen display image on your television screen indefinitely. If you leave the still video image or onscreen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Plasma display panels and projection televisions are especially susceptible to this.

If you have any questions or problems concerning your recorder, please consult your nearest Sony dealer.

Table of Contents

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Quick Guide to Disc Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Recordable and playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Hookups and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Hooking Up the Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Step 1: Connecting the Aerial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Step 2: Connecting the Video Cords/HDMI Cord . . . . . . . . . . . . . . . . . . . . .13

About the SMARTLINK features (for SCART connections only). . . . . . . 14

Step 3: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Step 4: Connecting the Mains Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Step 5: Preparing the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Controlling TVs with the remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

If you have a Sony DVD player or more than one Sony DVD recorder

Changing programme positions of the recorder using the remote . . . . . 20

Step 6: Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connecting a VCR or Similar Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Connecting to the LINE 3 jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Connecting to the LINE 2 IN jacks on the front panel . . . . . . . . . . . . . . . 23

Connecting to a Satellite or Digital Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Eight Basic Operations — Getting to Know Your DVD Recorder

1. Inserting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

2. Recording a Programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Checking the disc status while recording . . . . . . . . . . . . . . . . . . . . . . . . 26

3. Playing the Recorded Programme (Title List) . . . . . . . . . . . . . . . . . . . . . .27

4. Displaying the Playing/Remaining Time and Play Information . . . . . . . . . 29

Checking the playing/remaining time. . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Checking the remaining disc space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5. Changing the Name of a Recorded Programme . . . . . . . . . . . . . . . . . . .32

6. Labelling and Protecting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Labelling a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Protecting a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

7. Playing the Disc on Other DVD Equipment (Finalise) . . . . . . . . . . . . . . .34

Finalising the disc using Z (open/close) button . . . . . . . . . . . . . . . . . . .35

Finalising the disc using “Disc Information” display. . . . . . . . . . . . . . . . .35

Unfinalising a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

8. Reformatting a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

. . . 19

Guide to Digital Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

EPG (Electronic Programme Guide) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Viewing a list of available channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Viewing programmes related to a specific category . . . . . . . . . . . . . . . .39

Programme Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Displaying the programme information . . . . . . . . . . . . . . . . . . . . . . . . . . 40

,continued

Viewing a Digital Text Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Selecting digital text from dedicated digital teletext channels. . . . . . . . . 41

Selecting digital text from other channels . . . . . . . . . . . . . . . . . . . . . . . . 42

Favourites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Setting the Favourites List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Watching or listening to a favourite channel . . . . . . . . . . . . . . . . . . . . . . 43

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Before Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Recording mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Unrecordable pictures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Timer Recording (Standard/EPG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Setting the timer manually (Standard). . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Recording TV programmes using the EPG. . . . . . . . . . . . . . . . . . . . . . . 49

Recording programmes using Series Recording . . . . . . . . . . . . . . . . . . 50

Using the Quick Timer function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Adjusting the recording picture quality and size . . . . . . . . . . . . . . . . . . . 52

Creating chapters in a title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Checking/Changing/Cancelling Timer Settings . . . . . . . . . . . . . . . . . . . . . . 54

Checking/changing/cancelling using the EPG . . . . . . . . . . . . . . . . . . . . 54

Checking/changing/cancelling using the Timer List . . . . . . . . . . . . . . . . 55

Recording From Connected Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Recording from connected equipment with a timer (Synchro Rec) . . . . . 57

Recording from connected equipment without a timer . . . . . . . . . . . . . . 58

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Playback options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Adjusting the delay between the picture and sound (AV SYNC) . . . . . . 63

Pausing a TV Broadcast (TV Pause/Pause Live TV) . . . . . . . . . . . . . . . 63

Playing from the beginning of the programme you are recording

(Chasing Playback). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Playing a previous recording while making another

(Simultaneous Rec and Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Searching for a Title/Chapter/Track, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Playing MP3 Audio Tracks, JPEG Image Files, or DivX

About MP3 audio tracks, JPEG image files, and DivX video files. . . . . . 67

MP3 audio tracks, JPEG image files, or DivX video files that the recorder

can play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

About playback order of albums, tracks, and files. . . . . . . . . . . . . . . . . . 68

Video Files . . . . . 66

Erasing and Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Before Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Erasing and Editing a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Erasing multiple titles (Erase Titles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Erasing a section of a title (A-B Erase) . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Dividing a title (Divide) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Creating chapters manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Creating and Editing a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Moving a Playlist title (Change Order). . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Combining multiple Playlist titles (Combine) . . . . . . . . . . . . . . . . . . . . . . 76

Dividing a Playlist title (Divide) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Dubbing (HDD y DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Before Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

About “Dub Mode” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Dubbing a single title (Title Dubbing). . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Dubbing multiple titles (Dub Selected Titles). . . . . . . . . . . . . . . . . . . . . .82

DV Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Before DV Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Preparing for DV dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Recording an Entire DV Format Tape (One Touch Dubbing) . . . . . . . . . . . . 86

Program Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Clock and Language Settings (Basic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Digital TV settings (DTV Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

Favourites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

Parental Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93

Video Settings (Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Audio Settings (Audio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Recording Settings (Recording) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Disc Settings (DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

Remote Control Settings/Factory Settings (Others) . . . . . . . . . . . . . . . . . .103

Easy Setup (Resetting the Recorder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

Self-diagnosis Function (When letters/numbers appear in the display) . . . 112

Notes About This Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113

About i.LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114

Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116

Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Quick Guide to Disc Types

Recordable and playable discs

Type Disc Logo

Hard disk drive (internal)

DVD+RW

VR mode

DVDRW

Video mode

DVD+R

DVD+R DL

Icon used in this manual

HDD

RWVR

Video

Formatting (new discs)

Formatting unnecessary

Automatically formatted in +VR mode (DVD+RW VIDEO)

Format in VR mode (page 25)

Format in Video mode (page 25)

Automatically formatted in +VR mode (DVD+R VIDEO)

Compatibility with other DVD players (finalising)

Dub HDD contents to a DVD to play on other DVD players

Playable on DVD+RW compatible players (automatically finalised)

Playable only on VR mode compatible players (finalisation unnecessary)

Playable on most DVD players (finalisation necessary) (page 34)

Format in VR

DVD-R

VR mode

RVR

mode (page 25) Formatting is performed using the “Disc Information”

Playable only on DVD-R in VR mode compatible players (finalisation necessary) (page 34)

display.

Video mode

Automatically

Video

formatted in Video mode

Playable on most DVD players (finalisation necessary) (page 34)

Usable disc versions (as of August 2006)

• 8x-speed or slower DVD+RWs

• 6x-speed or slower DVD-RWs (Ver.1.1, Ver.1.2 with CPRM

)

• 16x-speed or slower DVD+Rs

• 16x-speed or slower DVD-Rs (Ver.2.0, Ver.2.1 with CPRM

)

• 8x-speed or slower DVD+R DL (Double Layer) discs

“DVD+RW,” “DVD-RW,” “DVD+R,” “DVD+R DL,” and “DVD-R” are trademarks.

When an unformatted DVD-R is inserted into this recorder, it is automatically formatted in Video mode. To format a new DVD-R in VR mode, format using the “Disc Information” display (page 25).

CPRM (Content Protection for Recordable Media) is a coding technology that protects copyrights for images.

Discs that cannot be recorded on

• 8 cm discs

• DVD-R DL (Dual Layer) discs

• DVD-RAMs

,continued

Playable discs

Type Disc Logo

DVD VIDEO

VIDEO CD

DATA DVD —

DATA CD —

8 cm DVD+RW/ DVD-RW/DVD-R

——

Icon used in this manual

DVD

VCD

DATA DVD

DATA CD

Characteristics

Discs such as movies that can be purchased or rented This recorder also recognizes DVDRAMs and DVD-R Dual Layer (Video mode) discs as DVD Video compatible discs. If the DVD-RAM has a removable cartridge, remove the cartridge before playback.

VIDEO CDs or CD-Rs/CD-RWs in VIDEO CD/Super VIDEO CD format

Music CDs or CD-Rs/CD-RWs in music CD format

DVD+RWs/DVD+Rs/DVD-RWs/ DVD-Rs/DVD-ROMs containing either JPEG image files or DivX video files

CD-ROMs/CD-Rs/CD-RWs containing either MP3 audio tracks, JPEG image files or DivX video files

8 cm DVD+RW, DVD-RW, and DVD-R recorded with a DVD video camera (Still images recorded with a DVD video camera cannot be played.)

“DVD VIDEO” and “CD” are trademarks.

DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.

is a video file compression technology,

DivX developed by DivX, Inc.

Discs that cannot be played

• PHOTO CDs

• CD-ROMs/CD-Rs/CD-RWs that are

recorded in a format different from the formats mentioned in the table above.

• Data part of CD-Extras

• DVD-ROMs/DVD+RWs/DVD-RWs/ DVD+Rs/DVD-Rs that do not contain DVD Video, DivX video or JPEG image files.

• DVD Audio discs

• Cartridge-only type DVD-RAMs and/or DVD-RAMs that do not contain DVD Video.

• HD layer on Super Audio CDs

• DVD VIDEOs with a different region code (page 11).

• DVDs that were recorded on a different recorder and not correctly finalised.

Maximum recordable number of titles

Disc Number of titles*

HDD 300

DVD-RW/DVD-R 99

DVD+RW/DVD+R 49

DVD+R DL 49

* The maximum length for one title is eight hours.

Note on playback operations of DVD VIDEOs/VIDEO CDs

Some playback operations of DVD VIDEOs/ VIDEO CDs may be intentionally set by software producers. Since this recorder plays DVD VIDEOs/VIDEO CDs according to the disc contents the software producers designed, some playback features may not be available. See the instructions supplied with the DVD VIDEOs/VIDEO CDs.

Region code (DVD VIDEO only)

Your recorder has a region code printed on the rear of the unit and will only play DVD VIDEOs (playback only) labelled with identical region codes. This system is used to protect copyrights. DVD VIDEOs labelled will also play

ALL

on this recorder. If you try to play any other DVD VIDEO, the message “Playback prohibited by region code.” will appear on the TV screen. Depending on the DVD VIDEO, no region code indication may be labelled even though playing the DVD VIDEO is prohibited by area restrictions.

Region code

Note on DualDiscs

A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed.

b Notes

• Some DVD+RWs/DVD+Rs, DVD-RWs/DVDRs, DVD-RAMs, or CD-RWs/CD-Rs cannot be played on this recorder due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The disc will not play if it has not been correctly finalised. For more information, see the operating instructions for the recording device.

• You cannot mix VR mode and Video mode on the same DVD-RW. To change the disc’s format, reformat the disc (page 36). Note that the disc’s contents will be erased after reformatting.

• You cannot shorten the time required for recording even with high-speed discs.

• It is recommended that you use discs with “For Video” printed on their packaging.

• You cannot add new recordings to DVD+Rs, DVD-Rs, or DVD-RWs (Video mode) that contain recordings made on other DVD equipment.

• In some cases, you may not be able to add new recordings to DVD+RWs that contain recordings made on other DVD equipment. If you do add a new recording, note that this recorder will rewrite the DVD menu.

• You cannot edit recordings on DVD+RWs, DVD-RWs (Video mode), DVD+Rs, or DVD-Rs that are made on other DVD equipment.

• If the disc contains PC data unrecognizable by this recorder, the data may be erased.

• You may not be able to record on some recordable discs, depending on the disc.

Music discs encoded with copyright protection technologies

This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are being marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

Hookups and Settings

Hooking Up the Recorder

Follow steps 1 through 6 to hook up and adjust the settings of the recorder. Do not connect the mains lead until you reach “Step 4: Connecting the Mains Lead” on page 17.

b Notes

• See “Specifications” (page 113) for a list of supplied accessories.

• Plug in cords securely to prevent unwanted noise.

• Refer to the instructions supplied with the components to be connected.

• You cannot connect this recorder to a TV that does not have a SCART or video input jack.

• Be sure to disconnect the mains lead of each component before connecting.

Step 1: Connecting the Aerial Cable

Connect the aerial cable by following the steps below.

Aerial cable (supplied)

to AERIAL OUTto AERIAL IN

DVD recorder

: Signal flow

1 Disconnect the aerial cable from your TV, and connect it to AERIAL IN on the rear

panel of the recorder.

2 Connect AERIAL OUT of the recorder to the aerial input of your TV using the supplied

aerial cable.

Step 2: Connecting the Video Cords/HDMI Cord

Select one of the following patterns, A through E, according to the input jack on your TV monitor, projector, or AV amplifier (receiver). This will enable you to view pictures.

INPUT

VIDEO

AUDI O

TV, projector, or AV amplifier (receiver)

Audio/video cord (not supplied)

(yellow)

Component video cord (not supplied)

COMPONENT

VIDEO IN

B/CB

R/CR

TV, projector, or AV amplifier (receiver)

to COMPONENT VIDEO OUT

(green)

(blue)

(red)

Hookups and Settings

to HDMI OUT

HDMI cord (not supplied)

to LINE 2 OUT (VIDEO)

to LINE 2 OUT (S VIDEO)

S-video cord (not supplied)

(green)

to i LINE 1 – TV

(red)(blue)

DVD recorder

SCART cord (not supplied)

E C A

INHDMI

TV, projector, or AV amplifier (receiver)

: Signal flow

S VIDEO

INPUT

TV, projector, or AV amplifier (receiver)

,continued

A SCART input jack

When you set “Easy Setup - Line1 Output” to “S Video” or “RGB” (page 21), use a SCART cord that conforms to the selected signal.

B Video input jack

About the SMARTLINK features (for SCART connections only)

If the connected TV (or other connected equipment such as a set top box) complies with SMARTLINK, NexTView Link MEGALOGIC CINEMALINK

, EASYLINK*2,

, Q-Link*3, EURO VIEW LINK*4, or T-V LINK*5, you can enjoy the following SMARTLINK features.

For recording

• TV Direct Rec.

You can easily record what you are watching on your TV (page 26).

• One Touch Timer

You can turn on the recorder and TV, set the TV to the recorder’s programme position, and display the timer programming menu with one touch of the [TIMER] button (page 48).

• One Touch EPG

You can turn on the recorder and TV, set the TV to the recorder’s channel, and display the Electronic Programme Guide screen with one touch of the (GUIDE) button (page 38).

For playback

• One Touch Play You can turn on the recorder and TV, set the TV’s input to the recorder, and start playback with one touch of the H (play) button (page 60).

• One Touch Menu You can turn on the recorder and TV, set the TV to the recorder’s programme position, and display the Title List menu with one touch of the TITLE LIST button (page 60).

For settings

• Automatic Power Off The recorder will turn off automatically if the recorder is not used after you turn off the TV.

“MEGALOGIC” is a registered trademark of Grundig Corporation.

“EASYLINK” and “CINEMALINK” are trademarks of Philips Corporation.

“Q-Link” and “NexTView Link” are trademarks of Panasonic Corporation.

“EURO VIEW LINK” is a trademark of Toshiba Corporation.

“T-V LINK” is a trademark of JVC Corporation.

z Hint

SMARTLINK also works with TVs or other equipment having EPG Timer Control, EPG Title Download, and Now Recording functions. For details, refer to the operating instructions supplied with your TV or other equipment.

Hookups and Settings

b Notes

• The SMARTLINK features are available only when “Video” is selected in “Line1 Output.”

• The power must be turned on to use all SMARTLINK features except One Touch Play, One Touch Menu, One Touch Timer and One Touch EPG.

• Not all TVs respond to the functions above.

Step 3: Connecting the Audio Cords

Select one of the following patterns, A or B, according to the input jack on your TV monitor, projector, or AV amplifier (receiver). This will enable you to listen to sound.

HDMI cord (not supplied)

to HDMI OUT

Rear (L)

Front (L)

Centre

[Speakers]

AV amplifier (receiver) with a decoder

to DIGITAL OUT (COAXIAL)

to LINE 2 OUT (R-AUDIO-L)

Audio/video cord

(white)

(not supplied)

[Speakers]

Rear (R)

Front (R)

Subwoofer

to coaxial/HDMI digital input

Coaxial digital cord (not supplied)

DVD recorder

INPUT

VIDEO

(yellow)

(red)

(yellow)*

: Signal flow

* The yellow plug is used for video signals (page 13).

A Digital audio input jack

If your AV amplifier (receiver) has a Dolby*1 Digital, DTS*2, or MPEG audio decoder and a digital input jack, use this connection. You can enjoy Dolby Digital (5.1ch), DTS (5.1ch), and MPEG audio (5.1ch) surround effects.

(white)

(red)

AUDIO

TV, projector, or AV amplifier (receiver)

B Audio L/R (left/right) input jacks

This connection will use your TV’s or stereo amplifier’s (receiver’s) two speakers for sound.

z Hint

For correct speaker location, see the operating instructions supplied with the connected components.

b Notes

• Do not connect your TV’s audio output jacks to the LINE IN (R-AUDIO-L) jacks at the same time. This will cause unwanted noise to come from your TV’s speakers.

• With connection B, do not connect the LINE IN (R-AUDIO-L) and LINE 2 OUT (R-AUDIO-L) jacks to your TV’s audio output jacks at the same time. This will cause unwanted noise to come from your TV’s speakers.

• With connection A, after you have co mpleted the connection, make the appropriate settings under “Easy Setup - Audio Connection” (page 21). Otherwise, no sound or a loud noise will come from your speakers.

• When you connect the recorder to an AV amplifier (receiver) using an HDMI cord, you will need to do one of the following: – Connect the AV amplifier (receiver) to the TV

with the HDMI cord.

– Connect the recorder to the TV with a video

cord other than HDMI cord (component video cord, S VIDEO cord, or audio/video cord).

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

Step 4: Connecting the Mains Lead

Connect the supplied mains lead to the AC IN terminal of the recorder. Then plug the recorder and TV mains leads (power cords) into the mains. After you connect the mains lead, you must wait for a short while before operating the recorder. You can operate the recorder once the front panel display lights up and the recorder enters standby mode. If you connect additional equipment to this recorder (page 22), be sure to connect the mains lead after all connections are complete.

to AC IN

to mains

Hookups and Settings

Step 5: Preparing the Remote

You can control the recorder using the supplied remote. Insert two R6 (size AA) batteries by matching the 3 and # ends on the batteries to the markings inside the battery compartment. When using the remote, point it at the remote sensor on the recorder.

b Notes

• If the supplied remote interferes your other Sony

DVD recorder or player, change the command mode number for this recorder (page 19).

• Use the batteries correctly to avoid possible

leakage and corrosion. Should leakage occur, do not touch the liquid with bare hands. Observe the following: – Do not use a new battery with an old battery, or

batteries of different manufacturers. – Do not attempt to recharge the batteries. – If you do not intend to use the remote for an

extended period of time, remove the batteries. – If battery leakage occurs, wipe out any liquid

inside the battery compartment, and insert new

batteries.

• Do not expose the remote sensor (marked on the front panel) to strong light, such as direct sunlight or a lighting ap paratus. The recorder may not respond to the remote.

• When you replace the batteries of the remote, the code number and Command Mode may be reset to the default setting. Set the appropriate code number and Command Mode again.

Controlling TVs with the remote

You can adjust the remote’s signal to control your TV.

b Notes

• Depending on the connected unit, you may not be able to control your TV with some or all of the buttons below.

• If you enter a new code number, the code number previously entered will be erased.

Number buttons

TV 2 +/–

TV/DVD

TV PROG

+/–

TV [/1 TV t

1 Hold down the TV [/1 button located

at the bottom of the remote.

Do not press the [/1 button at the top of the remote.

2 With the TV [/1 button pressed down,

enter the TV’s manufacturer code using the number buttons.

For instance, to enter “09,” press “0” then “9.” After you enter the last number, release the TV [/1 button.

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

Manufacturer Code number

Sony 01 (default)

Grundig 11

Hitachi 24

ITT/Nokia 15, 16

JVC 33

Loewe 45

Nokia 69, 73

Panasonic 17, 49

Philips 06, 07, 08, 72

Saba 12, 13, 74

Samsung 22, 23, 71

Sanyo 25

Sharp 29

Telefunken 36

Thomson 43, 75

Toshiba 38

The remote performs the following:

Buttons Operations

TV [/1 Turns your TV on or

TV 2 (volume) +/–

TV PROG +/– Selects the

TV t Switches your TV’s

off

Adjusts the volume of your TV

programme position on your TV

input source

To operate the TV/DVD button (for SCART connections only)

The TV/DVD button switches between the recorder and the last input source selected on the TV. Point your remote at the recorder when using this button. When you connect the recorder to the TV via the SCART jacks, the input source for the TV is set to the recorder automatically when you start playback. To watch another source, press the TV/DVD button to switch the TV’s input source.

If you have a Sony DVD player or more than one Sony DVD recorder

If the supplied remote interferes with your other Sony DVD recorder or player, set the command mode number for this recorder and the supplied remote to one that differs from the other Sony DVD recorder or player after you have completed “Step 6: Easy Setup.” The default command mode setting for this recorder and the supplied remote is DVD3.

Number buttons

SYSTEM MENU

M/m, ENTER

Hookups and Settings

1 Check that “Easy Setup” (page 21)

has been finished. If “Easy Setup” has not been finished, first perform “Easy Setup.”

2 Press SYSTEM MENU.

The System Menu appears.

,continued

3 Select “SETUP,” and press ENTER.

4 Select “Others,” and press ENTER.

5 Select “Command Mode,” and press

ENTER.

To check the Command Mode for the recorder

Press x on the recorder when the recorder is turned off. The Command Mode for the recorder appears in the front panel display.

If the Command Mode for the recorder has not been changed, set the Command Mode for the remote to the default setting of DVD3. If the Command Mode for the remote is changed to DVD1 or DVD2, you will be unable to operate this recorder.

Changing programme positions of the recorder using the remote

You can change programme positions of the recorder using the number buttons.

Number buttons

6 Select a Command Mode (DVD1,

DVD2, or DVD3), and press ENTER.

7 Set the Command Mode for the remote

so it matches the Command Mode for the recorder you set above.

Follow the steps below to set the Command Mode on the remote.

1 Hold down ENTER. 2 While holding down ENTER, enter

the Command Mode code number using the number buttons.

Command Mode Code number

DVD1 number button 1

DVD2 number button 2

DVD3 number button 3

3 Hold down both the number and

ENTER buttons at the same time for more than three seconds.

ENTER

Example: for channel 50 Press “5,” “0,” then press ENTER.

Step 6: Easy Setup

Make the basic adjustments by following the on-screen instructions in “Easy Setup.” Be careful not to disconnect the cables or exit the “Easy Setup” function during this procedure.

[/1

</M/m/,,

RETURN

ENTER

TV [/1

Easy Setup - TV Type (page 94)

If you have a wide-screen TV, select “16:9.” If you have a standard TV, select either “4:3 Letter Box” (shrink to fit) or “4:3 Pan Scan” (stretch to fit). This will determine how “wide-screen” images are displayed on your TV.

Easy Setup - Component Out

If you are using the COMPONENT VIDEO OUT jack, select “On.”

Easy Setup - Line1 Output

To output video signals, select “Video.” To output S video signals, select “S Video.” To output RGB signals, select “RGB.” Select “Video” to enjoy the SMARTLINK features (page 14).

• If you set “Easy Setup - Component Out” to “On,” you cannot select “RGB.”

Easy Setup - Audio Connection

If you connected an AV amplifier (receiver) using a coaxial cord, select “Yes : DIGITAL OUT” and set the digital output signal (page 98).

3 Press ENTER when “Finish” appears.

“Easy Setup” is finished.

Hookups and Settings

1 Turn on the recorder and your TV.

Then switch the input selector on your TV so that the signal from the recorder appears on your TV screen.

The initial settings message appears.

• If this message does not appear, select “Easy Setup” from “SETUP” in the System Menu (page 104).

2 Press ENTER.

Follow the on-screen instructions to make the following settings.

Easy Setup - Auto Tune

The recorder will automatically capture and store the available TV and Radio channels.

Easy Setup - Clock

The recorder will automatically search for a clock signal. If a clock signal cannot be found, set the clock manually using </M/m/,, and press ENTER.

To return to the previous step

Press O RETURN.

z Hints

• If your AV amplifier (receiver) has an MPEG audio decoder, set “MPEG” to “MPEG” (page 98).

• If you want to run “Easy Setup” again, select “Easy Setup” from “SETUP” in the System Menu (page 104).

Connecting a VCR or Similar Device

After disconnecting the recorder’s mains lead from the mains, connect a VCR or similar recording device to the LINE IN jacks of this recorder. Use the DV IN jack on the front panel if the equipment has a DV output jack (i.LINK jack) (page 84). For details, refer to the instruction manual supplied with the connected equipment. To record on this recorder, see “Recording from connected equipment without a timer” on page 58.

Connecting to the LINE 3 jack

Connect a VCR or similar recording device to the LINE 3 jack of this recorder.

VCR

to i LINE 3

SCART cord (not supplied)

to i LINE 1 – TV

DVD recorder

to SCART input

b Notes

• Pictures containing copy protection signals that prohibit any copying cannot be recorded.

• If you pass the recorder signals through a VCR, you may not receive a clear image on your TV screen.

VCRDVD recorder TV

Be sure to connect your VCR to the DVD recorder and to your TV in the order shown below. To watch video tapes, watch the tapes through a second line input on your TV.

Line input 1

VCR TV

DVD recorder

Line input 2

• The SMARTLINK features are not available for devices connected via the DVD recorder’s LINE 3 jack.

• When you record to a VCR from this DVD recorder, do not switch the input source to TV by pressing the TV/DVD button on the remote.

• If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected VCR.

Connecting to the LINE 2 IN jacks on the front panel

Connect a VCR or similar recording device to the LINE 2 IN jacks of this recorder. If the equipment has an S-video jack, you can use an S-video cord instead of an audio/video cord.

VCR, etc.

S VIDEO

OUTPUT

VIDEO

AUDI O

Hookups and Settings

S-video cord

(not supplied)

to LINE 2 IN

Audio/video cord (not supplied)

DVD recorder

: Signal flow

z Hint

When the connected equipment outputs only monaural sound, connect to just the L(MONO) and VIDEO input jacks on the front of the recorder. Do not connect the R input jack.

b Notes

• Do not connect the yellow LINE IN (VIDEO) jack when using an S-video cord.

• Do not connect the output jack of this recorder to another equipment’s input jack with the other equipment’s output jack connected to the input jack of this recorder. This may cause noise (feedback).

• Do not connect more than one type of video cord between the recorder and your TV at the same time.

Connecting to a Satellite or Digital Tuner

Connect a satellite or digital tuner to this recorder using the LINE 3 jack. Disconnect the recorder’s mains lead from the mains when connecting the tuner. To use the Synchro-Rec function, see below.

Satellite tuner, CanalSat, etc.

SCART cord (not supplied)

to SCART input

to i LINE 3

If the satellite tuner can output RGB signals

This recorder accepts RGB signals. If the satellite tuner can output RGB signals, connect the TV SCART connector on the satellite tuner to the LINE 3 jack, and set “Line3 Input” of “Scart Setting” to “Video/ RGB” in the “Video” setup (page 96). Note that this connection and setup disable the SMARTLINK function. If you want to use the SMARTLINK function with a compatible set top box, see the instructions supplied with the set top box.

to i LINE 1 – TV

DVD recorder

If you want to use the Synchro Rec function

This connection is necessary to use the Synchro-Recording function. See “Recording from connected equipment wit h a timer (Synchro Rec)” on page 57. Set “Line3 Input” of “Scart Setting” in the “Video” setup (page 96) according to the specifications of your satellite tuner. See your satellite tuner’s instructions for more information. If you are using a Sky, be sure to connect the tuner’s VCR SCART jack to the LINE 3 jack. Then set “Line3 Input” of “Scart Setting” according to the specifications of the VCR SCART jack on your satellite tuner.

b Notes

• Synchro-Recording does not work with some tuners. For details, see the tuner’s operating instructions.

• If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected tuner.

Eight Basic Operations

— Getting to Know Your DVD Recorder

1. Inserting a Disc

Video

DATA CD

Z (open/ close)

RWVR-RW

DVD

VCD CD

Video

RVR

DATA DVD

DVD

1 Press DVD. 2 Press Z (open/close), and place a

disc on the disc tray.

2. Recording a Programme

HDD

RVR-R

Video

RWVR-RW

This section introduces the basic operation to record a current TV programme to the hard disk (HDD) or to a disc (DVD). For an explanation of how to make timer recordings, see page 45.

HDD DVD

Video

PROG +/–

DISPLAY

Eight Basic Operations — Getting to Know Your DVD Recorder

Recording/playing side facing down

3 Press Z (open/close) to close the disc

tray.

Wait until “LOAD” disappears from the front panel display. Unused DVDs are formatted automatically.

• For DVD-RW discs DVD-RWs are formatted in the recording format (VR mode or Video mode) set by “Format DVD-RW” in the “DVD” setup.

• For DVD-R discs DVD-Rs are automatically formatted in Video mode. To format an unused DVD-R in VR mode, format the disc using the “Disc Information” display (page 36) before you make a recording.

If the disc is recordable on this recorder, you can manually re-format the disc to make a blank disc (page 36).

z REC x REC

STOP

TV/DVD

REC MODE

TV t

1 Press HDD or DVD.

If you want to record to a DVD, insert a recordable DVD.

2 Press PROG +/– to select the

programme position or input source you want to record.

3 Press REC MODE repeatedly to select

the recording mode.

Each time you press the button, the display on the TV screen changes as follows:

For more details about the recording mode, see page 45.

,continued

4 Press z REC.

Recording starts. Recording stops automatically after 8 hours of continuous recording or when the HDD or DVD is full.

Checking the disc status while recording

You can check the recording information such as recording time or disc type.

To stop recording

Press x REC STOP. Note that it may take a few seconds for recorder to stop recording.

To watch another TV programme while recording

If your TV is connected to the i LINE 1 – TV jack, set your TV to the TV input using the TV/DVD button and select the programme you want to watch. If your TV is connected to the LINE 2 OUT or COMPONENT VIDEO OUT jacks, set the TV to TV input using the TV t button (page 18).

TV Direct Rec.

If you are using the SMARTLINK connection and the “TV Direct Rec.” is set to “On” (page 101), you can easily record what you are watching on your TV. When the TV and the recorder are turned on, press z REC. The recorder starts recording what you are watching on your TV.

b Notes

• If “TV” appears in the front panel display, you cannot turn off the TV or change the programme position during TV Direct Rec. To turn off the function, set “TV Direct Rec.” to “Off” in the “Recording” setup (page 101).

• After pressing z REC, it may take a short while to start recording.

• You cannot change the recording mode while recording.

• If there is a power failu re, the programme you are recording may be erased.

Press DISPLAY during recording.

The recording information appears.

A Disc type/format B Recording status C Recording mode D Recording time

Press DISPLAY to turn off the display.

3. Playing the Recorded Programme (Title List)

Title List with Thumbnail Images (Example: DVD+RW)

HDD

RVR

Video

RWVR-RW

Video

To play a recorded title, select the title from the Title List.

HDD DVD

TITLE LIST

</M/m/,, ENTER

OPTIONS

CM x

1 Press HDD or DVD.

If you select DVD, insert a DVD (see “1. Inserting a Disc” on page 25). Playback starts automatically depending on the disc.

2 Press TITLE LIST.

To show the extended Title List, press OPTIONS to select “Display List,” and press ENTER.

Eight Basic Operations — Getting to Know Your DVD Recorder

Extended Title List

A Disc type:

Displays the media type, HDD or DVD. Also displays the title type (Original or Playlist) for HDD or DVD-RW/DVD-R (VR mode) disc titles.

B Disc space (remainder/total) C Title information:

Displays the title number, title name, and recording date. Title size is shown in the Thumbnail title list. z (red): Indicates that the title is currently being recorded.

: Indicates that the title is currently

being dubbed.

: Indicates the protected title. “NEW”: Indicates that the title is newly recorded (not played back) (HDD only).

: Indicates titles containing “CopyOnce” copy protection signals (HDD only) (page 80).

D Scroll bar:

Appears when all of the titles do not fit on the list. To view the hidden titles, press M/m.

E Title’s thumbnail picture:

The still images for each title are displayed.

,continued

3 Select a title, and press ENTER.

The sub-menu appears. The sub-menu displays options applicable only to the selected item. The displayed options differ depending upon the model, situation, and disc type.

Sub-menu

4 Select “Play,” and press ENTER.

Playback starts from the selected title.

To change the title order (Sort)

While the Title List menu is turned on, press OPTIONS to select “Sort Titles.” Press M/m to select the item, and press ENTER.

Order Sorted

By Date In order of when the titles

By Title In alphabetical order.

By Number In order of recorded title

Unseen Title (HDD only)

were recorded. The title that is recorded most recently is listed at the top.

number.

In order of when the titles were recorded. The title that is recorded most recently and has not been played is listed at the top. Playlist titles are not displayed.

To stop playback

Press x (stop).

To scroll the list display by page (Page mode)

Press / while the list display is turned on. Each time you press / , the entire Title List changes to the next/previous page of titles.

About the Title List for HDD/DVD-RWs/ DVD-Rs (VR mode)

You can switch the Title List to show Original or Playlist titles. While the Title List menu is turned on, press </,.

To change a title thumbnail picture (Thumbnail) (HDD/DVD-RW/DVD-R in VR mode only)

You can select a favourite scene for the thumbnail picture shown in the Title List menu.

1 Press TITLE LIST.

Press </, to switch the Title Lists, if necessary.

2 Select a title, and press ENTER.

The sub-menu appears.

3 Select “Set Thumbnail,” and press

ENTER. The display for setting the thumbnail point appears and the title starts to play.

4 While watching the playback picture,

press m/M to select the scene you want to set for a thumbnail picture, and press ENTER. Playback pauses.

5 Press ENTER if the scene is correct.

If the scene is incorrect, press c/C to select the scene you want to set for a thumbnail picture, and press ENTER. The display asks for confirmation.

• To change the thumbnail, press M.

6 Select “OK,” and press ENTER.

The scene is set for the title’s thumbnail picture.

To turn off the Title List

Press TITLE LIST.

z Hints

• After recording, the first scene of the recording (the title) is automatically set as the thumbnail picture.

• You can select “TITLE LIST” from the System Menu.

b Notes

• The title names may not appear for DVDs created on other DVD recorders.

• It may take a few seconds for the thumbnail pictures to be displayed.

• After editing, the title thumbnail picture may change to the first scene of the recording (title).

• After dubbing, the title thumbnail picture set on the source recording is cancelled.

4. Displaying the Playing/Remaining Time and Play Information

Video

RWVR-RW

DVD

VCD

HDD

RVR

DATA DVD

DATA CD

You can check the playing time and remaining time of the current title, chapter, track, or disc. Also, you can check the disc name recorded on the DVD/CD.

Video

DISPLAY

TIME/TEXT

ENTER

OPTIONS

Eight Basic Operations — Getting to Know Your DVD Recorder

Press DISPLAY.

The displays differ depending on the disc type or playing status.

A Title number/name

(Shows either track number, track name, scene number, or file name for CDs, VIDEO CDs, DATA DVDs, or DATA CDs.)

,continued

B Available functions for DVD VIDEOs

( angle/ audio/ subtitle, etc.), or playback data for DATA DVDs and DATA CDs

C The current selected function or audio

setting (appears only temporarily) Example: Dolby Digital 5.1 ch

Rear (L/R)

Front (L/R) + Centre

LFE (Low Frequency Effect)

D The current selected angle

E Disc type F Title type (

/format (page 8)

only appears for Playlists)

G Play mode H Recording mode (page 45) I Playing status bar

J Title number (chapter number*3)

(page 65) (Shows either track number, scene number, album number

, or file number for CDs, VIDEO CDs, DATA DVDs, or DATA CDs.)

K Album name appears for DATA DVDs

or DATA CDs. For CDs with CD text, press TIME/ TEXT.

L Playing time (remaining time

Displays Super VIDEO CDs as “SVCD,” DATA CDs as “CD” and DATA DVDs as “DVD.”

Does not appear with VIDEO CDs, DATA DVDs, and DATA CDs.

Displayed when you press TIME/TEXT repeatedly.

)

z Hints

• If “ DTS” of “Audio Connection” is set to “Off” in the “Audio” setup, the DTS track selection option will not appear on the screen even if the disc contains DTS tracks (page 98).

• When “Auto Display” is set to “On” (default) in the “Video” setup (page 97), information automatically appears on the screen when the recorder is operated.

b Note

Playing time of MP3 audio tracks may not be displayed correctly.

Checking the playing/ remaining time

You can view the playing or time information displayed on the front panel display.

Press TIME/TEXT repeatedly.

The displays differ depending on the disc type or playing status.

Example: When playing a DVD

Playing time and number of the current title

Remaining time of the current title

Playing time and number of the current chapter

Remaining time of the current chapter

Example: When playing a VIDEO CD

Playing time and number of the current scene or track

+ 94 hidden pages