This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
PFM-42X1/42X1N
Page 3
Table of Contents
1. Communication Parameters ...................................................... 1-1
Return Data1 - Data2 : 0x0000 - 0xFFFFH Frequency = Return Data x 10 [Hz]
V Frequency = Return Data / 100 [Hz]
Code table (4-b)
Function
0x04H Frequency
0x05V Frequency
Execute Judge ACK
StandbySetupPower
Sequence
DisableDisableEnable
DisableDisableEnable
On
(f) Sync polarity enquiry
Syntax
Enquiry
Execute Judge
Answer
Enquiry
Execute Judge
Header
0x83
0x89
Header
0x70
0x70
0x70
0x70
Category
0x30
Answer
0x00
0x03
0x03
0x04
Function
0x06
Return Data Size
0x01
Data1
0xFF
0xFF
Return Data1
Code Table
(4-c)
Data2
0xFF
0xFF
Completed
Command Canceled
Command Disable
Command All Enable
PFM-42X1/42X1N
1-15
Page 20
Code table (4-c)
Function
0x00H : Nega / V : Nega
0x01H : Nega / V : Posi
0x02H : Posi / V : Nega
0x03H : Posi / V : Posi
0x04SonG
0x05No H/V Sync
Execute Judge ACK
StandbySetupPower
Sequence
DisableDisableEnable
DisableDisableEnable
DisableDisableEnable
DisableDisableEnable
DisableDisableEnable
DisableDisableEnable
On
1-16
PFM-42X1/42X1N
Page 21
5. User Memory
(a) Load/save
Syntax
Control
Execute Judge
Header
0x8C
0x89
(b) Memory name
Syntax
Control
Enquiry
Execute Judge
Answer
Control
Enquiry
Execute Judge
Header
0x8C
0x83
0x89
Header
0x70
0x70
0x70
0x70
0x70
0x70
0x70
Category
0x40
Category
0x40
Answer
0x00
0x01
0x02
0x03
0x00
0x03
0x04
Function
Code Table (5-a) - [a]
Function
0x02
Return Data Size
0x06
Data1
0x01
0xFF
Data1
0x07
Code Table (5-b)
0xFF
Return Data1 Return Data2
Return Data1 to Data6 : Character Data
(0x00 - 0xFF)
Data2
Code Table
(5-b)
0xFF
Code Table (5-b)
0xFF
0xFF
Data2
......
...
......
Completed
Limit Over
Limit Under
Command Canceled
Completed
Command Disable
Command All Enable
Code table (5-a)
[a] Function
0x00Memory Load
0x01Memory Save
0x02Memory Name
Execute
Execute
Execute
[b] Range/Switch code
Code table (5-b)
Memory Number
0x00User Memory 10x0AUser Memory 11
0x01User Memory 20x0BUser Memory 12
0x02User Memory 30x0CUser Memory 13
0x03User Memory 40x0DUser Memory 14
0x04User Memory 50x0EUser Memory 15
0x05User Memory 60x0FUser Memory 16
0x06User Memory 70x10User Memory 17
0x07User Memory 80x11User Memory 18
0x08User Memory 90x12User Memory 19
0x09User Memory 100x13User Memory 20
Command
ControlEnquiry
YesNo
YesNo
YesNo
Execute Judge ACK
StandbySetupPower
Sequence
DisableDisableEnable
DisableDisableEnable
EnableEnableEnable
On
PFM-42X1/42X1N
1-17
Page 22
6. User Reset
Syntax
Control
Execute Judge
Answer
Control
Execute Judge
Code table (6)
Function
0x00Picture Reset
0x01Audio Reset
0x02Size Reset
0x03PLL Reset
Header
0x8C
0x89
Header
0x70
0x70
0x70
0x70
Category
0x50
Answer
0x00
0x03
0x03
0x04
Function
Code Table (6)
Completed
Command Canceled
Command Disable
Command All Enable
Range/Switch codeCommand
0x01
0xFF
Data1
Data2
0xFF
0xFF
ControlEnquiry
YesNo
YesNo
YesNo
YesNo
Execute Judge ACK
StandbySetupPower
DisableDisableEnable
DisableDisableEnable
DisableDisableEnable
DisableDisableEnable
Sequence
On
1-18
PFM-42X1/42X1N
Page 23
7. Answer
(a) Normal message
Answer
Header0x70Normal answer header
Category0xXXCode table (7-a) : Normal code
Code table (7-a)
Normal code
0x00Completed
0x01Limit over
0x02Limit under
0x03Command cancelled
0x04Command all enable
0x05Fail
Normal response.
The packet was received normally, but the data value was over the upper
limit.
Forcedly the monitor adjusted the data to maximum value.
The packet was received normally, but the data value was under the lower
limit.
Forcedly the monitor adjusted the data to minimum value.
The packet was received normally, but the command was cancelled because
the function was not in adjustable mode, such as a function displayed as “—
—” in user menu.
The packet was received normally.
The command function is all enable.
The packet was received normally, but the command was cancelled .
Please retry.
(b) Error message
Answer
Header0xE0Error answer header
Category0xXXCode table (7-b) : Error code
Code table (7-b)
Normal code
0x00No function error
0x02Data number error
0x06Mode error
0x07Time out
Packet header,category or function codes do not exist in this protocol.
The data value in “Data num” area of received packet was different from the
function’s own data number.
The monitor is already in the service mode via remote commander
operation.
(The service mode through IR remote has priority over the serial remote
command. )
Packet communication are interrupted by some error, and did not return to
normal communication within 2 seconds.
PFM-42X1/42X1N
1-19
Page 24
Page 25
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche
schriftliche Erlaubnis der Sony Corporation.