Sony MP-CL1 Help Guide
Help guide
MP-CL1
3.45 m
120
inches
80
inches
2.3 m
1.15 m
40
inches
3-MP0-107-01
© 2015 Sony Corporation
Parts and controls
CAUTION
Do not point the laser light directly at eyes or people, nor look into it. Doing so may
cause serious injuries such as loss of eyesight.
Strap hole
Micro USB jack
Use an AC power adaptor with a 1.5 A or
greater output to charge this product.
(power) button
Press and hold the (power) button for
longer than 1 second to turn the power
on or off.
Jog lever (−/ENTER/+)
Press the jog lever while at the ENTER position to display the menu. Slide it to +
or − to move to next or previous menu item, and then press while at the ENTER
position to select the highlighted item.
Speaker
Built-in Wi-Fi antenna
HDMI/MHL IN jack
AUDIO OUT jack
Connect headphones or speakers to this jack.
USB OUT jack (for power supply)
Connect another device to this jack to charge it. The
while charging the device.
Ventilation holes
(charge) lamp
(power) lamp
Lens
Laser radiates from this aperture.
lamp lights up in green
Adjusting the volume
Slide the Jog Lever to + or − while the menu is not displayed to adjust the volume.
Checking the remaining battery power
Press and quickly release the button (within 1 second). The lamp blinks in
orange, showing the battery status. The lamp blinks in one of the following patterns
according to the remaining battery power.
(Once): 0% to 30% remaining
(Twice): 30% to 70% remaining
(Three times): 70% to 100% remaining
Using the menu
Navigating the menu
Learn how to navigate through the menu here.
Press the jog lever while at the ENTER
1
position.
The menu is projected.
Slide the jog lever to + or − to move to the next or previous menu item.
2
Press the jog lever while at the ENTER position with the desired menu
3
item highlighted.
One of the following is displayed according to the selected menu item.
Values to choose from
Slide the jog lever to + or − to move to the next or
previous value, and then press the lever while at the
ENTER position with the desired value highlighted.
Submenu
Slide the jog lever to + or − to move to the next or
previous submenu item, and then press the lever
while at the ENTER position with the desired item
highlighted. The adjustment bar or another screen is
displayed according to the selected item.
Adjustment bar
Slide the jog lever to + or − to change the value
shown in the bar, and then press the lever while at
the ENTER position to confirm.
To exit the menu
Press and hold the jog lever for about 2 seconds while at the ENTER position.
Description of the menu items
Close Exits the menu.
Input change Selects an input source from HDMI/MHL and screen mirroring
according to the connection method.
Keystone
Keystone
Preset 1/
Preset 2/
OFF
V keystone Corrects vertical distortion. The
If the projected image is distorted and looks trapezoidal, select
Keystone Preset 1] or [ Keystone Preset 2] to apply the
[
keystone adjustment. The default values of [ Keystone Preset 2]
is suitable for correcting distortion when using the 2 Way Stand
(supplied). The preset values can be customized by changing the
settings in [ V keystone] and/or [ H keystone] below.
value set here overwrites the
selected preset value.
H keystone
Corrects horizontal distortion.
The value set here overwrites the
selected preset value.
Flip (left-right)
Picture setting
Contrast Adjusts the contrast of the projected image.
Hue Adjusts the color tones.
Flips the image horizontally. Use
this mode for rear projection.
To flip the image back to normal,
select this menu again.
Saturation Adjusts the color intensity.
Loading...