Sony KV-32FX65 B User Manual

4-205-753-41(02)

420575341

Trinitron Colour Television

Operating Instructions

KV-32FX65 B

Safety Information

For your safety

All TVs operate on extremely high voltages. To prevent fire or electric shock, please follow the safety procedures indicated below.

For General Safety

• Do not expose the TV set to rain or moisture.

• Do not remove the rear cover.

• For your protection, refer all servicing to qualified personnel only.

For Safe Installation

• Do not install the TV in hot, humid or excessively dusty places.

• Do not block or cover the ventilation openings. For ventilation, leave a space of at least 10 cm all around the set.

• Do not install the TV where it may be exposed to mechanical vibrations.

• Place the TV set only on a stable stand designed for the weight and dimensions of the TV.

For Safe Operation

• Do not operate the TV set on anything other than a 220-240V AC, 50Hz supply.

• Do not operate the TV if any liquid or solid objects fall in through the ventilation slots. Have it checked immediately.

• For environmental and safety reasons, it is recommended that the TV set is not left in standby mode when not in use. Switch off at the mains.

• Do not disconnect the TV by pulling on the power cable. Disconnect by removing the mains plug.

• In case of a thunderstorm, disconnect the TV set from the main supply and the aerial. Otherwise the set may be damaged by a stroke of lightning.

For Maintenance

• Clean the TV screen with a soft dampened cloth. Do not use any abrasive cleaners.

• Dust and nicotine deposits may cause heat accumulation inside the TV set. In the long term this could be a safety risk and may shorten the lifetime of your TV set. Therefore have your set serviced about every five years.

Table of Contents

Installation

1. Checking the accessories supplied

2. Inserting batteries into the remote control

3. Connecting the TV

4. Switching on the TV

5. Tuning your TV

6. Finding your video channel

Operation

Overview of the TV set buttons Overview of the remote control buttons NexTView Teletext Using the TV menu system

Adjusting the picture and sound Using the Features menu Re-arranging the TV channels Manually tuning the TV Naming a channel Skipping programme positions Using the ‘Further Programme Preset’ feature Adjusting the picture rotation Adjusting the picture geometry for an RGB source Inputting your personal ID Presetting and naming input signals

4 4 5 6 7 7

8 9 10 12 14 14 16 17 17 18 18 19 20 20 21 21

Additional Equipment

Connecting additional equipment to the TV Additional information when connecting equipment Smartlink

Additional Information

Specifications Channel Display Table Troubleshooting

22 23 23

24 24 25

Installation

Follow steps 1-6 to install the TV and view TV programmes.

1. Checking the accessories supplied

Batteries

Remote control

2. Inserting batteries into the remote control

Always observe the correct polarity when inserting batteries. Always remember to dispose of used batteries in an environmentally friendly way.

Installation

3. Connecting the TV

Connecting an aerial to your TV

1. Connect your existing aerial lead to the socket marked on the rear of the TV set.

If you are not connecting your TV to a VCR, please connect the aerial lead (as shown left) and proceed to section ‘4.Switching on the TV’.

If you are connecting your TV to a VCR please refer to the section below.

Connecting an aerial and VCR to your TV

scart lead (not supplied)

OUT

AC IN

AERIAL ANTENNA

1. Connect your existing aerial lead to your VCR as shown.

existing aerial lead

The scart lead is optional. If it can be used however, this additional connection can improve picture and sound quality when in play mode.

2. Connect the VCR aerial lead from the RF OUT socket on the back of the VCR to the aerial socket on the back of the TV as shown.

3. Connect the scart lead (if used) to the AV2 socket on the rear of the TV set.

4. Connect the VCR set to the mains and switch on.

5. Insert a pre-recorded tape into the VCR and press the ‘PLAY’ button. This enables the TV set to locate and store the video channel during the ‘Tuning your TV’ procedure on page 7.

Installation

4. Switching on the TV

I/O

1. Connect the TV plug to the mains socket (220-240V AC, 50Hz).

2. Push in the on/off button on the front of the TV.

If the standby mode indicator on the front of the TV is lit, press the TV button on the remote control to switch on the TV set. Please be patient as the picture may take a few moments to appear on the TV screen.

Installation

5. Tuning your TV

Before you tune your TV, you will be asked to set your language and country.

1. The Language/Country menu appears on the TV screen with the word ‘English’ highlighted.

2. Press the v or V buttons on the remote control to select your chosen language then press the OK button to confirm.

3. Press v or V to select the country in which you wish to operate the TV then press the OK button to confirm your choice. Select ‘OFF’ if you do not want your channels stored in a given channel sequence starting from programme position 1.

4. The ‘autotune’ menu appears on the TV screen in your selected language. Press the OK button to confirm.

5. Ensure the aerial is connected as instructed, then press the OK button to confirm. The TV starts to automatically search and store all available channels for you. This may take a few minutes please be patient and do not press any buttons.

6. Once the TV has tuned all available channels the ‘Programme Sorting’ menu appears on the TV screen enabling you to change the order of the channels on your TV. If you wish to change the channel order, press the v or V buttons to select the channel you want to move, then press B. Press the v or V buttons to select the new programme number position for your selected channel then press the OK button to confirm. The selected channel now moves to its new programme position and the other channels move accordingly. Repeat this procedure if you wish to sort the order of other channels on your TV.

7. Press the MENU button to remove the menu from the TV screen.

8. Press the PROGR+/- or the numbered buttons to view the TV channels.

Note: If you would like to stop the autotune process at any stage,

press the OK button.

Language country

Language

Country

Select Language: Confirm:

Language country

Language

Country

Select Country: Confirm:

Programme Sorting

PROG CH LABEL

C03

C05

C07

C08

C09

C11

C12

C13

C14

C15

C16

Select Prog: Confirm:

Programme Sorting

PROG CH LABEL

C03

C05

C07

C08

C09

C11

C12

C13

C14

C15

C16

Select Position: Move: OK

TV 5

PRO 7 EU-SP SWF RTL SAT MDR DDI DSF RTL 2 KAB 1

TV 5

PRO 7 EU-SP SWF RTL SAT MDR DDI DSF RTL 2 KAB 1

Čeština

Deutsch

English

Español Français

Italiano

English

Germany

Great Britain

Hungary

C03 TV 5

Dansk

France

Greece

Ireland

Italy

6. Finding your video channel

If you have connected a VCR to your TV, you now need to find your video channel. Please refer to the ‘Connecting the TV’ section of this manual on page 3.

1. Press the PROGR+/- buttons on the TV remote control until your video picture appears on the TV screen.

Note: If you wish to move your video channel to a different programme position, refer to the ‘Re-arranging the TV channels’

section of this instruction manual.

Operation

Overview of the TV set buttons

Advanced Digital 100Hz Plus

Press the door flap as shown. The control panel appears.

O N

G /

D /

Video input button.

Press to select the input signals from VCR etc.

- +

MONO

L/G/S/I

R/D/D/D

Programme Up (+) or Down (-) buttons.

Press to select TV channels.

Volume control buttons.

Press to increase (+) /decrease (-) volume.

Master Reset button.

Press to return the picture and sound levels to factory settings. The Sony logo

will appear on the screen followed by the ‘Autotune’ screen. If you do not wish to retune your TV, press the b button on your remote control.

+ 22 hidden pages