Sony KV-32FX60B, KV-28FC60-Z, KV-32FC60, KV-32FC60-Z, KV-28FC60 User Manual

Trinitron Colour Television

4-205-029-12

Instruction Manual

Styrfunktioner

Bruksanvisning

Betjeningsvejledning

Kayttöohje

OδηγίεσXpήσησ

Bedienungsanleitung

KV-28FC60/28FC60/Z KV-32FC60/32FC60/Z

NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362 (i.e. marked with 2 or @ ) must be used. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse.

IMPORTANT

•

If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and an appropriate plug fitted in accordance with the following instructions: The wires in this mains lead are coloured in accordance with the following code: Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not connect either wire to the earth terminal in the plug which is marked by the letter E or by the safety earth symbol coloured green or green and yellow.

WARNING

• To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket

outlet. This plug cannot be used and should be destroyed.

• To prevent fire or shock hazard, do not expose the unit to rain or moisture.

• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing

to qualified personnel only.

Safety First

TV sets operate on extremely high voltages. To prevent fire or an electric shock, please follow the safety information below:

For General Safety

This TV set is designed to receive and reproduce audio and video signals. Any other use of the TV set is not permitted.

Never open the rear cabinet.

Refer servicing to qualified personnel only!

Do not expose the TV set to rain or moisture.

For Safe Installation

Do not block or cover the ventilation openings. For ventilation leave a space of at least 5 cm around the set.

Do not install the TV set in hot, humid or excessively dusty places.

Do not install the TV set where it may be exposed to mechanical vibrations.

Place the TV set only on a stable stand designed for the weight and dimensions of the TV.

For Safe Operation

Operate the TV set only on a 220- 240 V. AC, 50 Hz supply.

Unplug the TV set if any liquid or solid object falls in through the ventilation openings. Have it checked immediately!

When not in use, do not leave the TV set in standby mode. Disconnect the TV set if you are not going to use it for a longer period.

Disconnect the TV set only by pulling on the mains plug. Do not pull on the power cord itself.

In the event of a thunderstorm, you should not touch the aerial, mains plug or television. It could possibly cause an electric shock.

For Maintenance

When the TV is switched off, clean the screen with a soft dampened cloth. Do not use any abrasive cleaners.

Dust and nicotine deposits may cause heat accumulation inside the TV set. In the long term this could be a safety risk and may shorten the lifetime of your TV set. Therefore have your set serviced about every five years.

Table of Contents

Installation 4

1. Checking the accessories supplied 4

2. Inserting batteries into the remote control 4

3. Connecting the TV 5

4. Switching on the TV 6

5. Using your joystick 6

6. Tuning your TV 7

7. Finding your video channel 7

Operation 8

Overview of the TV set buttons 8 Overview of the remote control buttons 9 NexTView 10 Teletext 12 Using the TV menu system 14

Adjusting picture and sound 14 Using the Features menu 16 Changing the screen mode 17 Sorting TV channels 18 Manually tuning in channels 18 Naming a channel 19 Skipping programme positions 19 Using the Further Programme Preset function 20 Adjusting the picture geometry for an RGB source 20 Adjusting the picture rotation 21 Changing the speaker configuration for external loudspeakers 21 Inputting your Personal ID 22 Presetting and labelling of input sources 22

Optional Equipment 23

Selecting an input signal 23 Smartlink 24 Remote control of other Sony equipment 24

Additional Information 25

Specifications 25 Troubleshooting 26 Channel Guide 26

Installation

Follow steps 1-7 to install the TV and view TV programmes.

1. Checking the accessories supplied

2 x batteries (AA size)

1 x remote control

2. Inserting batteries into the remote control

Always remember to dispose of used batteries in an environmentally friendly way.

Installation

3. Connecting the TV

Connecting an aerial to your TV

If you are not connecting your TV to a VCR, please connect the aerial lead (as shown left) and proceed to section ‘4.Switching on the TV‘.

L/G S/I

R/D

L/G/S/IR/D/D/D

D/D

1 Connect your existing aerial lead to the socket marked ˘ on the rear of the TV set.

Connecting an aerial and VCR to your TV

L/G S/I

R/D D/D

L/G/S/IR/D/D/D

If you are connecting your TV to a VCR please refer to the section below.

The scart lead is optional. If it can be used however, this additional connection can improve picture and sound quality when in play mode.

(scart lead -

(existing aerial lead)

not supplied)

AC IN

OUT

1 Connect your existing aerial lead to your VCR as shown.

2 Connect the VCR aerial lead from the RF OUT socket on the back of the VCR to the aerial socket on the back of the

TV as shown.

3 Connect the VCR set to the mains and switch on.

4 Insert a pre-recorded tape into the VCR and press the ‘PLAY‘ button.

Installation

4. Switching on the TV

1 Connect the TV plug to the mains socket (220-240 V. AC, 50 Hz).

2 Push in the on/off button U on the front of the TV.

If the standby mode indicator u on the front of the TV is lit, press the TV button on the remote control to switch on the TV set. Please be patient as the picture may take a few moments to appear on the TV screen.

5. Using your joystick

Moving the joystick

Pressing the joystick

To move around the menus press the relevant arrow button.

To select an item in a menu press the joystick down in the middle.

Installation

6. Tuning your TV

Before you tune your TV, you will be asked to set your language and country.

1 The Language/Country menu appears on the TV

screen with the word ‘English‘ highlighted.

2 Push the joystick to $ or 4 to select your chosen

language then press the OK button to confirm. The country menu appears on screen with the word ‘OFF‘ highlighted. Select ‘OFF‘ if you do not want your channels stored in a given channel sequence starting from programme position 1.

3 Push the joystick to $ or 4 to select the country in

which you wish to operate the TV.

4 Press the OK button to confirm your choice. The ‘Set-

up‘ menu appears on the TV screen.

5 Push the joystick to $ or 4 to select ‘Auto Tuning‘

then press the OK button to confirm.

6 Push the joystick to ” and hold for 5 seconds.

Language/Country

Language

Country

Select language:

Language/Country

Language

Country

Select Country:

Set Up

Auto Tuning

Programme Sorting AV Preset Installation

Select:

Start Auto Tuning:

Cestina

Dansk

Deutsch

English

Español

Français

Italiano

Confirm: OK

English

Austria

Belgium Bulgaria

Czech Rep.

Denmark

Finland

Confirm: OK

Start

Off

Your TV will now start to tune in all available channels. This may take a few minutes - please be patient and do not press any buttons. Once the TV has tuned all available channels the menu disappears

CO2

CO3

CO4

CO7

CO8

Searching

from the screen and your TV is ready to use.

If you would like to stop the autotune process at any stage, press the OK button. The manual sort menu appears on the TV screen. For manual sorting instructions refer to the ‘Sorting TV channels‘ section of this instruction manual. To remove the sorting menu, press the MENU button on your remote control.

7. Finding your video channel

If you have connected a VCR to your TV, you now need to find your video channel.

1. Press the PROGR+/- buttons on your remote control until your video picture appears on the TV screen.

If you wish to move your video channel to a different programme position, refer to the ‘Sorting TV channels‘ section of this instruction manual.

Operation

Overview of the TV set buttons

You must press the control button to activate and illuminate the control panel before you can use the other buttons on top of the TV set.

Video input button.

Press to select the input signals from VCR etc.

Volume control buttons.

Press to increase (+)/ decrease (-) volume.

–

PROGR –

Programme Up (+) or Down (-) buttons.

Press to select TV channels.

CONTROL button.

Press to activate and illuminate the control panel.

CONTROL

On/Off switch.

Press to switch TV on and off.

Soul Music News Game Show Animal Report Stones in Interviev Pink Panther Afternoon Report

VIVA RTL SAT 1 S3 VIVA 2 PRO 7 ARD

11 12 13 14

Operation

Overview of the remote control buttons

VCR on/off button.

To mute sound.

Press to mute TV sound. Press again to restore the sound.

To return to TV mode.

Press to return to the normal operation from teletext mode, video mode or standby mode.

These buttons have no function.

To select Teletext

Press to select Teletext mode.

To select EPG

Press to display the Electronic Programme Guide. Press again to remove display.

To freeze the picture.

Press to freeze the picture. Press again to cancel freeze.

To select channels.

Press numbered buttons to select channels.

For double digit programme numbers, eg 23, press -/-- first, then the buttons 2 and 3. If you enter an incorrect first digit, this should be corrected by entering another digit (0-9) and then selecting -/-- button again to enter the programme number of your choice.

To display sound menu.

Press repeatedly to select one of the following equaliser modes : Personal, Vocal, Jazz, Rock, Pop or Flat.

To display picture menu.

Press to change the picture settings. Press the ; button to remove the display.

Press to temporarily switch off VCR (if Sony VCR connected). Press again to switch on VCR.

To temporarily switch off TV

Press to temporarily switch off TV. Press again to switch on TV from standby mode. NOTE: After 15 minutes without a TV signal and without any button being pressed, the TV switches automatically into standby mode.

To reveal channel information.

Press to reveal information on the channel you are currently watching. Press the

button again to

;

remove the display.

To select input signal or freeze teletext

Press to select inputs from the TV sockets (see Using Optional Equipment section). In teletext mode, press to freeze the displayed page. Press once again to cancel.

To return to previous channel

Press to return to the previous channel you were watching. Note: This can be done only after watching the present channel for 5 seconds.

To change screen format. Press to change the size of the screen.

This button can be used in Teletext mode only. Please see Teletext section of manual for details.

To select menu items

Use this OK button to select options available in the menu system of the TV.

To display the Channel Table

Press the OK button to display the channel

table. Push to $ or 4 to select a channel then push to ” to confirm.

To adjust TV volume.

Press to adjust the volume of the TV.

To reset to factory-set levels.

Open the remote control lid and press to return picture and sound settings to factory-set levels. After the ‘Installation‘ menu has appeared on the TV screen, refer to the ‘Selecting Language and Country‘ section of the instruction manual to change your choice of language and country if desired.

To select channels.

Press to select channels.

To display the menu

Press if you wish to use the TV menu system. Press again to remove the menu from the TV screen.

To display the time.

Open the remote control lid and press to display the time on screen.

To operate video equipment

Open the remote control lid and press these buttons to operate your video equipment (please refer to your VCR manual).

Operation

NexTView*

*depending on availability of service

NexTView is an electronic programme guide with up to 1 week* of programme information on those channels included in the selected provider. *If the data exceeds the memory of NexTView, you will get information on less than 7 days.

When looking for information you can search by theme (sports, art etc.), date or time (e.g. broadcasts between 8 and 9 p.m). When you‘ve found a programme you can go directly to this programme, use the timer to remind you of it or preset your VCR with Smartlink.

The NexTView provider is responsible for the contents of the guide. The TV set is responsible for the presentation, that is the menu structure and the navigation, if there is none from the provider. If there is a navigation from the provider the basic operation with the joystick is the same as described in the Sony navigation.

Displaying NexTView

At first you need to select a channel providing a NexTView Service. In this case the indication “NexTView“ is displayed as soon as all data is available. When you later change the channel you can still select this NexTView service.

1 Press

to switch NexTView on and off.

2 Use the joystick buttons as follows

moving up- or downwards within a column: Use $ or 4

•

Going to the left columns time and date: Use “

•

Going to the right column icons: Use ”

•

Confirming a selection: Press OK

•

a while in the columns date, time or icon (themes), the programme list changes according

to the selection.

b while in the programme list, confirming a running broadcast brings you directly to the

TV programme or confirming a future programme brings you to the long info menu (See Using the Long Info Menu).

07 Tue

12:38

Wed

Thu

Sun

Mon

Tue

10 Fri

Sat

SWISS

Star Wars Super RTL

Vets in Practice C5

Flui grüsst den Rest der Welt Kabel 1

Once upon a time in the West Euronews

International News RTL Plus

Documentary series which follows veterinary graduates as they embark on their careers. Continues on Friday

TXT TPS / RINGIER

10:35 - 12:45

10:20 - 12:00

10:45 - 10:50

11:00 - 11:20

11:45 - 12:50

Tue 07. 04 .98

Index

full list of selection sports

personal selection entertainment

news broadcasts children

movies back to last menu

Operation

Using the Individual Setting menu

When you select there will be no personal pre-selection. lets you make your own individual selection of themes, limiting the search to the marked ones.

1 Select

The Individual Setting menu is displayed.

2 Select the item you wish to mark using 4 or $. Confirm by pressing OK.

Repeat step 2 for all items you wish to have in your list.

using 4 or $. Push to ” to enter.

3 When you have finished the list, press ” to select

on the menu screen then press OK.

Using the Long Info menu

1 Select a future programme in the column programme list using 4 or $. Press OK.

The long info menu is displayed.

First nextTView/EPG-Providers in Europe

07 Tue

12:38

SWISS TXT TPS / RINGIER nexTView

Address Mapping The position of the addresses in the

OSDA is shown in the following diagram. The position values of the DPW are set to '0'.

If other values are set, the complete combination will be scrolled.

Example: if the DPWC is set to '63', the char-

This channel has been set for a timer

VPS/PDC Speed

Timer Prog

VCR1

On SP

Tue 07. 04 .98

You wish to record the selected programme with your VCR

(only with Smartlink VCRs) 2 Select

using “ and press OK.

The information is transferred to the VCR connected to your TV set.

Setting up your VCR 3 Select VPS/PDC pushing repeatedly to “.

With this setting on, you have the guaranteed recording of the whole broadcast should there be a change in the TV programme. This only works if the selected channel broadcasts a VPS/PDC signal.

Select On or Off using OK.

•

4 Select Speed using $.

Select between standardplay (SP) or longplay (LP) mode. With longplay you can record twice as much on a videotape. The picture quality, however, may suffer.

Select SP or LP using OK.

•

5 Select VCR Setup using $.

Select with which of the connected Smartlink-VCRs you wish to programme.

Select VCR 1 or 2 using OK.

•

To leave the menu

6 Select

using z. Press OK.

You are back in the last menu.

VPS/PDC

Speed VCR Setup

VCR1

Operation

Teletext

Most TV channels broadcast information via teletext. The index page of the teletext service (usually page 100) gives you information on how to use the service.

Please use a TV channel with a strong signal, otherwise there may be Teletext errors.

Switching Teletext on and off

1 Select the TV channel which carries the teletext service you want to view.

2a Press the button once on your remote control to switch Teletext on.

b Press

The TV broadcast and the Teletext display are overlapped.

3 Press ; or press a third time to switch teletext off.

Selecting a Teletext Page

Input the three digits of the page number using the number buttons on your remote control.

If you have made a mistake: Type in any three digits, then re-enter the correct page number.

again for Mix mode.

Page Catching 1 Using the number buttons on the remote control, select a teletext page which

has several page numbers on it (e.g. the index page).

2 Press the OK button.

Page Catching is displayed.

3 Select the desired page number using 4 or $ then press the OK button.

The requested page is displayed after some seconds.

Selecting the next or the preceding page

Press (Page +) or (Page -).

•

Selecting the index page

Press +.

•

Selecting a subpage

A teletext page may consist of several subpages. In this case an information line is displayed, showing the number of subpages. Select the mode by pushing to 4. Select the subpage by using 4 or $.

•

Freezing a Teletext subpage

1 Press to freeze the Teletext page.

2 Press

to resume normal teletext reception.

216-02

01 03 04 05 06 07 0802

Using Fastext*

*depending on availability of service

Fastext lets you access pages with one button stroke. When Fastext is broadcast, a colour-coded menu appears at the bottom of the screen. The colours of this menu correspond to the red, green, yellow and blue buttons on the remote control. Press the coloured button which corresponds to the colour in the

•

colour-coded menu.

Operation

Using the Teletext menu

This TV set has a menu-guided teletext system. When teletext is switched on you can use the joystick buttons to operate the teletext menu.

Select the menu functions as follows:

1 Press the MENU button on the remote control to display the Teletext menu. 2 Select the teletext function using 4 or $. Push to ” to enter.

Top/Bottom/Full

For convenient reading of a Teletext page you can enlarge it. After having selected the function, a sub menu Top 4 Bottom $ Full OK is displayed.

Push to 4 to enlarge the upper half of the screen, push to $ to enlarge the lower

•

half. Press OK to resume the normal size. Press Teletext operation.

Text Clear

After having selected the function, you can watch a TV channel while waiting for a requested Teletext page. As soon as the page is available, the symbol changes colour.

Press to view the page.

•

to resume the normal

Teletext

Top / Bottom / Full

Text Clear Reveal Time Page

Select: Enter Menu:

Top: Bottom: Full: OK

Reveal

Some teletext pages contain hidden information (e.g., for a quiz), which you can reveal. After having selected the function, the hidden information appears.

Press to resume the normal Teletext operation.

•

Time Page*

*depending on availability of service

You can call up a time-coded page - such as an alarm page - at a time specified by you.

After having selected the function a sub menu is displayed.

1 Select On using 4 or $. Push to ” to enter.

2 Enter the three digits of the desired page using the number buttons.

3 Enter the four digits of the desired time using the number buttons.

4 Press OK to store.

The time is displayed in the top left-hand corner of the screen. At the requested time the page is displayed.

Time Page

PAGE TIME – – – - - : - -

Select: Enter:

Operation

Using the TV menu system

The TV consists of a menu system which is based on a series of user friendly on-screen displays and menus. These displays will help you get the most from your TV, helping you to change picture and sound settings, to alter the size of the TV picture and to rearrange the TV channels etc.

Adjusting the picture and sound

Picture and sound are adjusted at the factory. You can however, adjust them individually.

1 Press MENU.

Select the symbol

for Picture or for Sound using 4 or $.

Push to ” to enter. The menu Picture or Sound Control is displayed.

2 Select the desired item using 4 or $. Push to ” to enter. 3 Adjust the selected item using 4, $, ” and “. Press OK to store.

Refer to the tables on this and the following page for more information.

Picture Adjustment

Picture Mode

Contrast Brightness Colour Sharpness Reset AI Noise Reduction Digital Mode

Select Mode: Enter:

Personal

Normal

On On

4 Repeat steps 2 and 3 to adjust other items.

5 Press MENU to return to the normal TV screen.

Picture Control

Item Effect/Operation

Picture Mode $ Live (for live broadcasts)

Personal (for individual settings)

4 Movie (for movie broadcasts) Contrast Less “” More Brightness* Darker “” Brighter Colour* Less “” More Hue** Reddish “” Greenish Sharpness* Softer “” Sharper

Reset Resets picture to the factory preset levels AI 4 Off: normal

(Artificial Intelligence) $ On: Automatic optimization of contrast level

according to the TV signal

Noise Reduction 4 Off: Normal

$ On: Reduces picture noise in case of a weak

broadcasting signal

Digital Mode $ Normal: 100 Hz.

Digital+: 100 Hz plus line flicker reduction

4 Advanced: Digital+ plus smoothing of motions

Picture Mode

Contrast

Noise Reduction

Digital Mode

Personal

Movie

Normal

Digital+

Advanced

Live

Off

* Only if Personal is selected in Picture Mode ** Only available for NTSC colour signal (e.g. US video tapes)

Operation (TV menu system):

Sound Control

Item Effect/Operation

Equaliser mode Select between the following sound settings

$ Personal

Vocal Jazz Rock Pop

4 Flat (fixed setting, cannot be adjusted)

Equaliser adjustment

Balance ” More right

Loudness $ Off: Normal

Space $ Off: Normal

Auto Volume Control 4 On: volume level of the channels will stay the same

Dual Sound For a bilingual broadcast:

Headphones

2 Volume Less “ ” More 2 Dual Sound For a bilingual broadcast:

You can adjust the mode selected in Equaliser mode by cutting and boosting of 5 selected frequency bands. Only the changes made in Personal can be stored, the others return to factory setting. Select the desired bar using ” or “, adjust using 4

•

and $. Press OK to store.

“ More left

4 On: For music broadcasts

4 On: Special accoustic effect

independent of the broadcast signal (e.g. in case of advertisements)

$ Off: volume level changes according to the

broadcast signal

$ A for channel 1 4 B for channel 2

For a stereo broadcast:

$ Mono 4 Stereo

In case of a NICAM stereo broadcast the indication NICAM appears briefly on the screen.

$ A for channel 1 4 B for channel 2

Personal

Audio Adjustment

Equaliser Mode

Equaliser Adjustment Balance Loudness Space Auto Vol. Control Dual Sound Volume Dual Sound

Select Mode: Confirm: OK

Equaliser Adjustment

Personal

+ 0 –

120 150 1,5K 5 K 10 K

Sel: Adjust: Confirm:OK

Balance

Loudness

Space

Auto Vol. Control

Dual Sound

Volume

Dual Sound

Personal

Vocal

Rock

Mono

Stereo

Jazz

Pop Flat

On Off Off

Off

Operation (TV menu system):

Using the Features menu

1 Press the MENU button on the remote control. Select the symbol using $.

Push to z to enter.

2 Select the desired menu item using $. Push to z to enter. 3 Select the desired setting using 4 or $.

4 Store by pressing OK.

5 Press MENU to return to the normal TV screen.

Features

Item Effect/Operation

Auto Format* 4 Off: Size of picture does not automatically adjust. *only for aerial signal Normal: Size of picture automatically adjusts

according to information from broadcaster.

$ Full: The TV can automatically adjust the picture

size to eliminate any dark areas on the TV picture (as shown below):

Features

Auto Format

Format Correction Sleep Timer

Parental Lock AV 2 Source

Select: Enter:

Auto Format

Normal

Off

Full

Off Off

Off

Full

Format Correction* 4 On: Smart mode is selected automatically for *only if Auto Format is 4:3/14:9 broadcasts set to ‘Normal‘ or ‘Full‘ $ Off: 4:3/14:9 is selected

Sleep Timer You can select a time period after which the TV

switches itself into standby mode

4 Off

10 min. 20 min.

. . .

$ 90 min. Parental Lock 4 Off: Normal mode

$ On: TV can only be switched on out of

standby-mode using the Remote Commander, the buttons on the TV do not work.

AV2 Source You can select the source to be output from the

Scart connector

Y2/j2. In this way you can

record from this socket while watching another source.

4 TV audio/video signal from the aerial ˘

AV1 audio/video signal from Scart 1 AV2 audio/video signal from Scart 2

$ AV3 audio/video signal from connectors on top or

bottom of rear of TV.

Format Correction

Sleep Timer

Parental Look

AV 2 Source

Off

10 min

Off

AV 1 AV 2 AV 3

Operation (TV menu system):

Changing the screen mode

When Auto Format in the Features menu is preset to ”Normal“ or “Full“, the TV set automatically selects the detected screen format. Screen mode, however, lets you select the screen format of your choice.

Press the button on the remote control repeatedly to get one of the

•

following formats:

Smart imitation of wide screen effect for 4:3 broadcasts, parts of the top and

bottom of the picture are cut off 4:3 conventional 4:3 aspect ratio, full picture information 14:9 compromise between 4:3 and 16:9 aspect ratios Zoom imitation of wide screen effect for letterboxed movies Wide for 16:9 broadcasts

In Zoom, Smart and 14:9 modes parts of the top and the bottom of the screen are cut off. Using 4 and $ you can adjust the position of the image onscreen to e.g. read subtitles. Press OK to confirm.

Smart

Zoom

Wide

Programme Sorting

Select Prog: Confirm:

PROG CH LABEL

Programme Sorting

Select Position: Move: OK

C03 TV 5

PROG CH LABEL

1 2 3 4 5 6 7 8 9 10 11

C03

C05 C07 C08 C09 C11 C12 C13 C14 C15 C16

TV 5

PRO 7 EU-SP SWF RTL SAT MDR DDI DSF RTL 2 KAB 1

C03

C05 C07 C08 C09 C11 C12 C13 C14 C15 C16

TV 5

PRO 7 EU-SP SWF RTL SAT MDR DDI DSF RTL 2 KAB 1

1 2 3 4 5 6 7 8 9 10 11

Operation (TV menu system):

Sorting TV channels

After tuning in TV channels, you may wish to rearrange the order of the channels.

1 Press the MENU button on your remote control. Select the symbol

using $.

Push to ” to enter.

2 Select Programme Sorting using $. Push to ” to enter. 3 Select the programme position of the channel you wish to sort using 4 or $.

Push to ” to enter.

4 Move the channel to the new programme position using 4 or $. Store by

pressing OK. The channel is now at the new position. The other programme positions move accordingly.

5 To sort other programme positions repeat steps 3 to 4.

6 Press MENU to return to the normal TV screen.

Manually tuning-in channels

Use this function to preset channels or a video input source one by one to programme positions of your choice.

1 Press the MENU button on the remote control. Select the symbol

Push to ” to enter.

2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position by pushing to 4 or $. Push twice to ”.

The column SYS is highlighted.

4 Select the TV system using 4 or $. Push to ” to enter.

Available TV systems are I for Ireland or EXT for a video input source (please go to step 5c after selecting EXT).

5 Select your method for the channel tuning using 4 or $. Push to ” to enter.

You have the choice between C for a terrestrial channel, S for a cable channel or F for direct frequency input.

6a Direct Channel Input

For channel numbers input a two digit number, for the channel frequency a three digit number.

Select the two or three digits by using the number buttons 0 to 9.

•

To start the search and to store the channel, press the OK button.

•

To preset other channels repeat steps 3 to 6a.

•

b Channel search (SEARCH)

Use Search if you do not know the channel number or frequency Start the search for the next available channel by pushing to $.

•

Store the channel by pressing OK or continue the search by pushing again to $.

•

To search for other channels repeat steps 3 to 6b.

•

c For video input sources (EXT)

Select the Video Input source using 4 or $.

•

Store your selection by pressing OK.

•

To allocate other sources repeat steps 3 to 5c.

•

6 Press MENU to return to the normal TV screen.

using $.

Installation

Language/Country

Manual Programme Preset

Further Programme Preset RGB Set Up Picture Rotation Speaker Configuration Personal ID

Select: Enter:

Manual Programme Preset

PROG CHSYSSKIP LABEL

Off

Select: Enter:

PROG CHSYS

SKIP LABEL Off

PROG SYS

SKIP LABEL Off

1 I

PROG SYS

SKIP LABEL Off

1 I

PROG CHSYS

SKIP LABEL Off

0 EXT

B/G B/G

EXT

Internal

- - - - - - -

C09

BBC1

C10

BBC

B/G

L I

D/K

AV1

AV2 AV3

AV1

Operation (TV menu system):

Manual Programme Preset

Select: Enter:

PROG CHSYSSKIP LABEL

C09 C10

ARD BBC

B/G B/G

Off Off Off Off Off Off Off Off Off Off Off

1 2 3 4 5 6 7 8 9 10 11

PROG CHSYS

Off

SKIP LABEL

6 I

C07 TE

Naming a channel

During tuning the channels are usually labelled automatically. You can, however, individually name a channel or a video input source.

1 Press the MENU button on the remote control. Select the symbol

using $.

Push to ” to enter.

2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position of the channel or the video source you wish to

label by pushing to $ or 4. Push repeatedly to ” until the first element of the position LABEL is highlighted.

4 Select a number, a letter, + or a blank using 4 or $. Push to ” to confirm.

Select the other four characters in the same way.

5 Store your selection by pressing OK.

6 To label other channels or video sources repeat steps 3 to 5.

7 Press MENU to return to the normal TV screen.

Skipping programme positions

In case of 100 programme positions there may be unused positions, which you can skip in the menu »Manual Programme Preset«. When changing channels with the PROGR +/– buttons they then do not appear. You can, however, still select them using the number buttons.

1 Press the MENU button on the remote control. Select the symbol

Push to ” to enter.

2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position you wish to skip by pushing to 4 or $.

Push to ” to enter. The column SKIP is highlighted.

4 Select ON using $.

5 Store by pressing OK.

6 To skip other programme positions repeat steps 3 to 5.

7 Press MENU to return to the normal TV screen.

using $.

Manual Programme Preset

PROG CHSYSSKIP LABEL

Off

Select: Enter:

PROG CHSYSSKIP LABEL

53 I

C09

BBC1

C10

BBC

F189 - - - Off

Operation (TV menu system):

Using the Further Programme Preset function

Using the menu Further Programme Preset you can

a) individually adjust the volume level of each channel.

b) improve the quality of a weak channel (picture or sound distortions) with

manual fine tuning.

c) preset the AV output for programme positions of those channels with

scrambled signals (e.g. from a Pay TV decoder). In this way a connected Smartlink VCR records the unscrambled signal.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter. Select Further Programme Preset

using $. Push to ” to enter.

3 Select the programme position of the desired channel by pushing to 4 or $.

Push repeatedly to ” to select: VOL (Volume Offset), AFT (Automatic Fine Tuning) or DECODER. The selected item changes colour.

4 a VOL

Push to 4 or $ to adjust the volume level (range -7 to +7) of the channel. Store by pressing OK. Repeat steps 3 and 4a if you wish to adjust the volume level of other channels.

b AFT

Push to 4 or $ to fine tune the channel (range -15 to +15). Store by pressing OK. Repeat steps 3 and 4b if you wish to fine tune other channels.

c DECODER

Push to 4 or $ to select AV1 (Euro AV socket 1) or AV2 (Euro AV socket 2) as output for the video source on this programme position. Store by pressing OK. Repeat steps 3 and 4c if you wish to preset the AV output of other video sources.

Should you use Auto Tuning afterwards, this setting will be cancelled.

using $. Push to ” to enter.

Installation

Language/Country Manual Programme Preset

Further Programme Preset

RGB Set Up Picture Rotation Speaker Configuration Personal ID

Select: Enter:

Further Programme Preset

PROG AFTVOL DECODER

0 2 3 4 5 6 7 8 9 10 11

Select: Enter:

PROG AFTVOL DECODER

1 -5

PROG AFTVOL DECODER

1 -5 On

Internal

- - - - - - -

Off Off Off

AV1 AV2

Off

5 Press MENU to return to the normal TV screen.

Adjusting the picture geometry for an RGB source

When connecting an RGB source such as a Sony playstation you may need to readjust the picture geometry.

1 Select the connected RGB source … 1 by pressing … repeatedly.

2 Press MENU. Select the symbol 3 Select Installation using $. Push to ” to enter. Select RGB Set Up using $.

Push to ” to enter.

4 Select H Centre by pushing to ”. Adjust the centre of the picture

(range from -10 to +10) using 4 or $. Store by pressing OK.

5 Select H Size using $. Push to ” to enter. Adjust the horizontal coordinates

(range from -10 to +10) using 4 or $. Store by pressing OK.

6 Press MENU to return to the normal TV screen.

using $. Push to ” to enter.

RGB Set Up

H Centre

H Size

Adjust Position: Confirm: OK

RGB Set Up

H Centre

H Size

Adjust Size: Confirm: OK

Operation (TV menu system):

Adjusting the picture rotation

Because of the earth‘s magnetism the picture might slant. In this case you can readjust the picture.

1 Press MENU. Select the symbol

using $. Push to ” to enter.

2 Select Installation using $. Push to ” to enter. Select Picture Rotation using $.

Push to ” to enter.

3 Adjust the Picture Rotation (adjusting range -5 to +5) by pushing to 4 or $.

Store by pressing OK.

4 Press MENU to return to the normal TV picture.

Changing the speaker configuration for external loudspeakers

When connecting external loudspeakers to your TV set, you need to set Speaker Configuration to ‘External‘. The subwoofer of the TV set is then witched off and you will get no sound distortions.

Installation

Language/Country Manual Programme Preset Further Programme Preset RGB Set Up

Picture Rotation

Speaker Configuration Personal ID

Rotate: Confirm: OK

1 Press MENU. Select the symbol

using $. Push to ” to enter.

2 Select Installation using $. Push to ” to enter. Select Speaker Configuration

using $. Push to ” to enter.

3 Select External for external speakers or Internal for the internal TV speakers

using 4 or $. Store by pressing OK.

4 Press MENU to return to the normal TV picture.

Installation

Language/Country Manual Programme Preset Further Programme Preset RGB Set Up Picture Rotation

Speaker Configuration

Personal ID

Select: Confirm: OK

External

Internal

Operation (TV menu system):

Inputting your personal ID

You can programme your TV with a safety code, so that you can be traced if your TV is stolen and recovered. This code can only be input once! Make sure to write it down in this Instruction Manual.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter. Select Personal ID using $.

Push to ” to enter.

3a Select the first of a total of 11 characters (letter, number, + or a blank) by

using 4 or $.

b Push to ” to go to the next character.

c Repeat a and b for all characters.

4 Store by pressing OK.

5 Press MENU to return to the normal TV screen.

using $. Push to ” to enter.

Installation

Language/Country Manual Programme Preset Further Programme Preset RGB Set Up Picture Rotation Speaker Configuration

Personal ID

Select A-Z, 0-9: Confirm: OK

- - - - - -

Presetting and labelling of input sources

Using AV Preset you can select the automatic format function and label an input source.

1 Press MENU. Select the symbol 2 Select AV Preset using $. Push to ” to enter. 3 Select the desired AV input (AV 1, 2 or 3) using 4 or $. Push to ” enter.

After each step you have the choice between memorizing (press OK) or going to the next item (push to ”).

4 For automatic format selection of the AV input:

a Push to ” to select AUTO FORMAT. b Select Off, Normal or Full using 4 or $.

5 To label the source:

a Push to ” to select Label. b Select the first character using 4 or $. Push to ” to confirm.

c Repeat step b to select the other 4 characters.

d Store by pressing OK.

6 Repeat steps 3 to 5 for the other AV inputs.

7 Selecting the AV3 Input Source:

In case of AV3 you have the choice between the top AV3 sockets on the rear of the TV or the rear Scart 3 connector.

a Push to $ to select AV3 Input. Push to ” to enter. b Select Top or Bottom using 4 or $.

c Store by pressing OK.

8 Press MENU to return to the normal TV screen.

using $. Push to ” to enter.

AV Preset

INPUT LABEL

AV 3 Input Rear

Select : Enter:

AV Preset

INPUT LABEL

AV 3 Input

Select Mode: Confirm: OK

AV 1

AV 2 AV 3

AV 1 AV 2 AV 3

AUTO 16:9

On On On

AUTO 16:9

On On On

Front

Rear

VIDEO VIDEO VIDEO

Optional Equipment

You can connect a wide range of optional equipment to your TV set.

L/G S/I

R/D D/D

L/G/S/IR/D/D/D

VHS

A B C

DVD

Selecting an input signal

In order to get the input signal of a connected equipment onto the TV screen, you need to select the symbol of the connector, to which you have connected the device.

Press … repeatedly on the remote control to select one of the following input modes:

Symbol on the screen Input signals from Connector

…1 Audio/Video from Scart connector D or* RGB from Scart connector D …2 Audio/Video from Scart connector E or* S-Video from Scart connector E …3 Audio/Video from the phono jacks A and B or from Scart connector F or* S-Video from

the 4-pin DIN connector C or from Scart connector F

* automatic detection of the signal according to the connected equipment

Press ; to return to the normal TV screen.

If the picture or sound is distorted, move the VCR away from the TV set.

When connecting a monaural VCR, connect only the white jack to both the TV set and the VCR.

Connect your DVD-player to Scart 2 Y2/j2 E.

For information on how to select the output signal of the Scart 2 Y2/j2 E, see page 16.

Optional Equipment

Smartlink

Smartlink is a direct link between your TV set and a VCR.

For Smartlink you need:

A VCR which supports Smartlink, NexTView Link, Easy Link or Megalogic.

A fully-wired 21-pin SCART cable to connect your VCR to Scart Y2/j2 connector.

The features of Smartlink are:

Tuning information such as the channel overview are downloaded from the TV set to the VCR.

With NexTView you can programme your VCR easily.

Direct TV recording: While watching TV you just need to press just one button on the VCR to record this programme.

For more information on Smartlink please refer to the Instruction Manual of your VCR.

Remote control of other Sony equipment

Using the buttons underneath the cover of the remote control you can control other Sony equipment.

1 Open the cover of the remote control.

2 Set the selector VTR 1234 DVD according to the equipment you want to control:

VTR 1 Beta VCR VTR 2 8 mm VCR VTR 3 VHS VCR VTR 4 Digital Video (DCR-VX 1000/9000 E, VHR-1000) DVD Digital Video Disk

3 Use the buttons on the remote control to operate the equipment.

If your video equipment has a COMMAND MODE selector, set this selector to the same position as the VTR 1234 DVD selector on the TV remote control.

If the equipment does not have a certain function, the corresponding button on the remote control does not work.

Additional Information

Specifications

Television B/G/H, D/K, I, L

system

Colour PAL, SECAM, NTSC 3.58/4.43 (via Video In)

system

Channel See Channel Guide on next page

coverage

Picture tube FD Trinitron

KV-28FC60/28FC60-Z Approx. 71 cm (28 inches) Approx. 66 cm picture measured diagonally

102° deflection

KV-32FC60/32FC60-Z Approx. 82 cm (32 inches) Approx. 76 cm picture measured diagonally

102° deflection

Sockets (Rear) input of audio/video or RGB signals

Y1/ 1: 21-pin scart connector

output of TV signals

Y2/j2:21-pin scart connector

input of audio/video or S-video signals selectable output of audio/video signals

Y3/j3:21-pin scart connector

input of audio/video or S-video signals output of audio/video signals (monitor out)

L/G/S/I RCA-connectors,

R/D/D/D variable output for audio signals

External speaker terminals:2-pin DIN (2) q 3 : 4-pin DIN input of S-video signals

…3 Phono jack input of video signals

≤ 3 Phono jacks

input of audio signals

Sound output Right and left speaker

2␣ x␣ 25W (music power), 2␣ x␣ 15W (RMS)

Power KV-28FC60/28FC60-Z: 132 W

consumption KV-32FC60/32FC60-Z: 130 W

Dimensions KV-28FC60/28FC60-Z

498(w) x 834(h) x 527(d) mm KV-32FC60/32FC60-Z 559(w)␣ x␣ 924(h)␣ x␣ 559(d)␣ mm

Weight KV-28FC60/28FC60-Z

Approx. 52␣ kg KV-32FC60/32FC60-Z Approx. 65 kg

Accessories 1 remote control RM-892 supplied 2 batteries

1 instruction manual 1 rear cover (for KV-28FC60Z/ 32FC60Z models only).

Other Features Flat display Trinitron tube, digital

noise reduction, 100 Hz picture, graphic equaliser, personal ID, sleep timer, NexTView, NICAM stereo, Digital Comb Filter

Sockets

(Front)

2 Headphones jack -stereo minijack

Additional Information

Troubleshooting

Here are some simple solutions to problems which may affect the picture and sound.

Problem Solution

No picture (screen is dark), no sound • Plug the TV in.

• Press U on the TV. (If u indicator is on, press

or one of the numbered buttons on the remote control.)

• Check the aerial connection.

• Check if the selected video source is on.

• Turn the TV off for 3 or 4 seconds and then turn it on again using U .

Poor or no picture (screen is dark), • Press MENU. Select but good sound and Colour.

Good picture, but poor or no sound • Press ¸ + .

• If ¤ is displayed on the screen, press ¤ button.

No colour for colour programmes • Open the cover of the remote control. Press ? button.

Remote control does not function • Replace the batteries.

Control Panel does not function • Make sure Parental lock is Off.

and adjust Brightness, Contrast

; , PROGR+/-

Note: As with some other electrical appliances under certain circumstances there is potential for small electrostatic

discharge to occur.

If you continue to have problems, have your TV serviced by qualified personnel. Never open the casing yourself.

Channel Guide

TV System Receivable Channels Channel Display

B/G/H E2 .. 12, 21 .. 69 C02 C03 C04 .. C12 C21 .. C69

TV Cable (1) S1 .. 41 S01 S02 .. S41

TV Cable (2) S01 .. S05, M1 .. M10, U1 .. U10 S42 .. S46 S01 .. S10 S11 .. S20

Italy A B C D E F G H H1 H2, 21 .. 69 C13 C14 C15 C16 C17 C18 C19 C20 C11 C12, C21-C69

D/K R01 .. R12, R21 .. R69 C01 .. C12 C21 .. C69

TV Cable (1) S01 S02 .. S41

TV Cable (2) S42 S43 .. S46

TV Cable B .. Q*, S21 .. F41 S02, S03 .. S17, S21 .. S41

L F2 .. F10 F21 .. F69 C01 .. C12, C21 .. C69

I B21 .. B68 C21 .. C68

* If channels B..Q are available, the display S02-S17 will appear on the screen.

+ 138 hidden pages