Sony KV-29FS60U, KV-32FS60D, KV-29FS60E, KV-29FS60A, KV-29FS60D User Manual

...

SERVICE MANUAL AE-5

www.ELEKO.de

Hier finden Sie das Service-Manual für die Modelle KV-29FS60A bis KV-29FS60U und KV-32FS60A bis KV-32FS60E.

CHASSIS

MODEL

KV-29FS60A KV-29FS60B KV-29FS60D KV-29FS60E KV-29FS60K KV-29FS60R KV-29FS60U

COMMANDER DEST CHASSIS NO.

RM-891 Italian SCC-Q12E-A

RM-891 French SCC-Q13E-A

RM-891 AEP SCC-Q11E-A

RM-891 Spanish SCC-Q14E-A

RM-891 OIRT SCC-Q16G-A

RM-891 OIRT SCC-Q16H-A

RM-891 UK SCC-Q15D-A

MODEL

COMMANDER DEST CHASSIS NO.

KV-32FS60A KV-32FS60B KV-32FS60D KV-32FS60E

RM-891 Italian SCC-Q12F-A

RM-891 French SCC-Q13F-A

RM-891 AEP SCC-Q11F-A

RM-891 Spanish SCC-Q14F-A

TRINITRON

MICROFILM

COLOR TV

ITEM MODEL Television System Stereo System Channel Coverage Color System

www.ELEKO.de

Italian

French

AEP

Spanish

OIRT

B/G/H,D/K GERMAN Stereo

B/G/H, D/K,L,I GERMAN/NICAM

B/G/H, D/K GERMAN Stereo

B/G/H, D/K GERMAN/NICAM

B/G/H, D/K

I NICAM Stereo UHF : B21-B69

Stereo

KV-29FS60K GERMAN/NICAM Stereo

KV-29FS60R GERMAN Stereo

ITALIA VHF : A-H2 (C) UHF : 21-69 PAL B/G/H VHF : E2-E12 UHF : E21-E69 CABLE TV (1) : S1-S41 CABLE TV (2) : S01-S05,M1-M10,U1-U10 DK VHF : R01-R12 UHF : R21-R69

L VHF : F02-F10 UHF : F21-F60 CABLE : B-Q B/G/H VHF : E2-E12 UHF : E21-E69 CABLE TV (1) : S1-S41 CABLE TV (2) : S01-S05, M1-M10, U1-U10 ITALIA VHF : A-H2 (C) UHF : 21-69 I UHF : B21-B69

PAL B/G/H/ VHF : E2-E12 : E21-E69 CABLE TV (1) : S1-S41 CABLE TV (2) : S01-S05, M1-M10, U1-U10 ITALIA VHF : A-H2 (C) UHF : 21-69 D/K VHF : R01-R12 UHF : R21-R69

PAL B/G/H/ VHF : E2-E12 : E21-E69 CABLE TV (1) : S1-S41 CABLE TV (2) : S01-S05, M1-M10, U1-U10 ITALIA VHF : A-H2 (C) UHF : 21-69

B/G/H/ VHF : E2-E12 UHF : E21-E69 CABLE TV (1) : S1-S41 D/K VHF : R01-R12 UHF : R21 R 9

PAL, SECAM NTSC4.43, NTSC3 58 (VIDEO IN)

PAL NTSC4.43, NTSC3 58 (VIDEO IN)

MODEL 29FS60A 29FS60B 29FS60D 29FS60E 29FS60K 29FS60R 29FS60U 32FS60A 32FS60B 32FS60D 32FS60E

Power

Consumption

[PICTURE TUBE] KV-29FS60

KV-32FS60

149Wh 148Wh 148Wh 148Wh 148W 1 8W 148Wh 144Wh 149Wh 149Wh 149Wh

[FRONT]

FD Trinitron Approx. 72 cm (29 inches) (Approx. 68 cm picture measured diagonally) 102 degree deflection

FD Trinitron Approx. 82 m (32 inches) (Approx. 76 cm pi ture measured diagon lly) 102 degr e deflection

Video output - phono jack

Audio inputs - phono jacks

S Video input - 4 pin DIN

Headphone jack : stereo minijack

Sound output 2x25W (Music Power) Power requirements 220 - 240V

Dimensions KV-29FS60 Approx 738 x 588 x 507 mm (w/h/d) KV-32FS60 Approx 867 x 564 x 558 mm (w/h/d)

Input/Output Terminals

[REAR]

21-pin Euro connector (CENELEC standard).

- Inputs for Audio and Video signals.

- Inputs for RGB.

- Outputs of TV Video and Audio signals. 21-pin Euro connector

- Inputs for Audio and Video signals.

- Inputs for S video.

- Outputs forVideo and Audio signals (selectable).

21-pin Euro connector

- Inputs for Audio and Video signals.

- Inputs for S video.

External speaker terminals : 2-pin DIN (5)

Weight KV-29FS60 Approx 55kg KV-32FS60 Approx 68kg

Supplied accessories RM-891 Remote Commander (1)

IEC designated R6 battery (2)

Other features NICAM*, FASTEXT, TOPTEXT

* (KV-29FS60B/29FS60E/29FS60K/

29FS60U/32FS60B/32FS60E only)

[RM-891]

www.ELEKO.de

Remote control system Infrared control Power requirements 3V dc

2 batteries IEC designation

R6 (size AA) Dimensions Approx 210x56x24mm (w/h/d) Weight Approx 110g (Not including battery)

Design and specifications are subject to change without notice.

Model Name

Item Pal Comb PIP RGB Priority Woofer Box Scart 1 Scart 2 Front in (3) Scart 4 Projector AKB in 16:9 mode Norm B/G Norm I Norm D/K Norm AUS Norm L

KV-29FS60A

KV-32FS60A

ON ON ON ON ON ON ON

OFFOFFOFFOFFOFFOFFOFF

ON ON ON ON ON ON ON

OFFOFFOFFOFFOFFOFFOFF

ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON

OFFOFFOFFOFFOFFOFFOFF

ON ON ON ON ON ON ON ON ON ON ON ON ON OFF

OFF ON OFF OFF OFF OFF ON

ON ON ON ON ON ON OFF OFFOFFOFFOFFOFFOFFOFF OFF ON OFF OFF OFF OFF OFF

KV-29FS60B

KV-32FS60B

KV-29FS60D

KV-32FS60D

KV-29FS60E

KV-29FS60K KV-29FS60R KV-29FS60U

KV-32FS60E

Norm SAT Norm M Teletext Nicam Stereo Language Preset

WARNING

The flexible mains lead is supplied connected to a having a fuse of use a

5 AMP FUSE

ASA

mark.

IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE OUTLET SOCKET. When an alternative type of plug is used it should be fitted with a

, otherwise the circuit should be protected by a

FUSE

distribution board.

(KV-29FS60U only)

5 AMP

approved by

OFFOF OFFOFFOFFOFFOFF OFFOFFOFFOFFOFFOFFOFF

ON ON ON ON ON ON ON OFF ON OFF ON ON OFF ON

Italia French German Spanish OIRT OIRT English

capacity. Should the fuse need to be replaced,

ASTA

B.S. 1363

BS 1362

fused plug

, ie one that carries the

5 AMP

5 AMP FUSE

at the

How to replace the fuse. Open the fuse compartment with a screwdriver blade and replace the fuse.

FUSE

21 pin connector

www.ELEKO.de

21 19 17 15 13 11

9 7 5 3 1

223

Pin No 1 2 4 Signal Signal level

GS I

RD D D

L/G/S/I

R/D/D/D

20 18 16

3 4 5 6

9 10 11

12 13 14

_ (S signal Chroma

Audio output B (right)

Audio output A (left)

Ground (audio) Ground (blue) Audio input A

(left) Blue input 0.7 +/- 3dB, 75 ohms positive

Function select (AV control)

Ground (green) Open G een Green signal : 0.7 +/- 3dB, 75 ohms,

Open G d (red) Ground (blanking)

_ _ Red input 0.7 +/- 3dB, 75 ohms, positive

input) Blanking input

(Ys signal) Ground (video

output) Ground (video

input) Video output 1V +/- 3dB, 75ohms, positive sync 0.3V

4 2

_ _ Video input 1V +/- 3dB, 75ohms, positive sync 0.3V

_ Video input

Y (S signal) Common ground

(plug, shield)

Standard level : 0.5V rms Output impedence : Less than 1kohm*

Standard level : 0.5V rms Output impedence : More than 10kohm*

Standard level : 0.5V rms Output impedence : Less than 1kohm*

Standard level : 0.5V rms Output impedence : More than 10kohm*

High s ate (9.5 2V) : Part mode L w sta (0-2V) : TV mode Inpu impedence : More than 10K ohms Input c pacitance : Less than 2nF

positive

0 3 +/- 3dB, 75 ohms, positive

High state (1-3V) Low state (0-0.4V) Input impedence : 75 ohms

(-3+10dB)

(-3+10dB) 1V +/- 3dB, 75ohms, positive sync 0.3V

(-3+10dB)

Connected Not Connected (open) * at 20Hz - 20kHz

Pin No.

1 2 3 4

Signal Ground Ground Y (S signal) input C (S signal) input

1V 3dB 75 ohm, positive Sync. 0.3V -3 + 10dB

0.3V 3dB 75 ohm, positive Sync.

Signal Level

L/G/S/I R/D/D/D

AE-5 SELF DIAGNOSTIC SOFTWARE

www.ELEKO.de

The identification of errors within the AE-5 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if b usy (F ailure to do so will report with continuous flashing LED) and then communicate with each device in turn to establish if a device is f aulty. If a device is found to be faulty the relevant device number will be displayed through the LED (Series of flashes which must be counted) See table 1., non fatal errors are reported using this method.

Diagnostic Item

Description

Power does not turn on Does not light Power cord is not plugged in

+B Overcurrent (OCP) 2 times H.OUT (Q6803/6804) is shorted. (D Board)

Vertical Deflection stopped 4 times +15V is not supplied R6835 ope (D Board)

No of times Standby

LED Flashes

Fuse is burned out

Linearity FET (Q6806) is shorted. (D Board) IC6604 Power IC is shorted. (D Board)

-15V is not supplied R6834 open (D B ard) IC6700 is shorted (D Board)

ERROR

No error 00 Not allowed (may be confused with Srcs response

flash!) Over Current Prote ti n 02 Over Voltage Protectio 03 Vertical Protec ion 04 AKB 05 H - Protectio 06 Speak r Protection 07 Ge eral IIC Line 0 error 08 MEGATEXT 09 NVM 10 Main colour decoder 11 Feature Box 12 D/A converter 13 Backend 14 Multi sound processor 15 Auto Wide 16 External RAM 17

Probable cause

Location

ERROR COUNT

LED

Detected Symptoms

Power does not come on No p wer is supplied to the TV AC power supply is faulty

Pow r do s not come on

Lo d on power line has shorted Vertical deflection pulse has stopped

Power line has shorted

Flash Timing Example : e.g. error number 3

StBy LED

ON ON ON

OFF OFF

ERROR DETECTION MONITOR

www.ELEKO.de

Device acknowledge is used to check IIC errors. Device acknowledge is checked by sending an IIC start sequence during CRT power on. Each device is checked three times, if there is no acknowledge after every attempt, it will be regarded as an error. There are three steps to check errors

1. IIC line 0 If all devices except the NVM have errors, IIC line 0 error is displayed

2. Board check If all devices mounted on one board have errors, board error is displayed

3. Each device check If IIC line error and board error are not detected then the device with an error is displayed

The detected errors can be displayed as follows:

1. Error Monitor Menu

2. Error Reader

1. ERROR MONITOR MENU

The error monitor menu is displayed by selecting TT33. The following menu will be displayed:

ERROR MONITOR

Operating Time :

930360h 15h

Saved Err rs :

1. 100h = A-Board

2. 401h = BP-B CXD2069 MID

3. 704h = J-B TDA9320 Main Col Dec

4. 000h = no error occured

5. 000h = no error occured

Actual Error :

New error code sequence is starting

Ignore Errors : [off]

2. ERROR READER DISPLAY

www.ELEKO.de

The error reader display is connected to the service connector to read actual error codes. The part number for the error reader display is S-188-900-10. Once an error has been detected it will then be displayed on the two digit error reader. The errors displayed refer to the following table :

Send Data to Error Reader

Error Code Data high Data Low Error type Function

00 00h - f0h no device

Gen.IIC Error

00 01h f0h 01h IIC 0 line 00 02h f0h 02h IIC 1 line not used

Board Error

01 00h f1h 00h A Board 02 00h f2h 00h B1 Board 03 00h f3h 00h B2 Board 04 00h f4h 00h BP Boa d 05 00h f5h 00h D1 Boa d 06 00h f6h 00h E oard 07 00h f7h 00h J Boar

Device Error

A Board

01 01h f1h 01h CXA1875 Port Expander 01 02h f1h 02h TU1326 Main Tuner 01 03h f1h 03h TU1350 Sub Tuner

B1 Board

02 01h f2h 01h P83C654 Feature Box 02 02h f2h 02h SDA9280 D/A Converter

B2 Board

03 01h f3h 01h SAA4977 Basic 03 02h f3h 02h SAA4950 Memory

BP Board

04 01h f4h 01h CXD2069 MID

D1 B ard

05 01h f5h 01h CXA8070 Dynamic Conv. 05 02h f5h 02h CXA1875 Port Expander

E Board

06 01h f6h 01h CXD2100 Backend

J Board

07 01h f7h 01h CXD2057 Auto Wide 07 02h f7h 02h SDA9288 PIP 07 03h f7h 03h TDA9320 Sub Colour 07 04h f7h 04h TDA9320 Main Colour 07 05h f7h 05h CXA1875 Sub Sound 07 06h f7h 06h TDA7309 HP Amp 07 07h f7h 07h TEA6422DT Audio SW 07 08h f7h 08h MSP3410D Sound Proc 07 09h f7h 09h TC9337F Sound DSP

TABLE OF CONTENTS

www.ELEKO.de

Section Title Page Section Title Page

Warning and Caution .....................3

Self-Diagnostic Function .....................5

1. GENERAL

Overview .....................9

Installation .....................10

Advanced Operations .....................11

Teletext .....................16

2. DISASSEMBLY

2-1. Rear Cover Removal .....................17

2-2. Chassis Assy Removal .....................17

2-3. Service Position .....................17

2-4. U Board Removal .....................17

2-5. J Board Removal .....................18

2-6. J Shield Removal .....................18

2-7. B1 Board Removal .....................18

2-8. Picture Tube Removal .....................19

Removal and Replacement of the

Main-Bracket bottom plates .....................20

3. SET-UP ADJUSTMENTS

3-1. Beam Landing .....................21

3-2. Convergence .....................22

3-3. Focus .....................24

3-4. Screen [G2] White Balance .....................24

4. CIRCUIT ADJUSTMENTS

4-1. Electrical Adjustments .....................26

4-2. Volume Electrical Adjustments .................. 32

4-3. Test Mode 2 .............. ...33

5. DIAGRAMS

5-1. Block Diagram (1) .....................35

Block Diagram (2) .....................40

Block Diagram (3) .....................45

Block Diagram (4) .....................50

5-2. Circuit Board Location .....................55

5-3. Schematic Diagrams and

Printed Wiring Boards .....................55

* C Board .....................57

* J Board .....................65

* U Board .....................74

* A Board .....................81

* BP Board .....................85

* VM Board .....................92

* B1 Board .....................95

* D1 Board .....................99

* F Board .....................103

* F1 Board .....................106

* M Board .....................107

* E Board .....................111

* D B ard .....................116

* H1 Board .....................122

5-4. Semi onductors .....................125

5-5. IC Blocks .....................128

6. EXPLODED VIEWS

6-1 Chassis .....................129

6 2. Picture Tube . ....................131

7 ELECTRICAL PARTS LIST

.....................133

CAUTION

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE CARBON PAINTED ON THE CRT, AFTER REMOVAL OF THE ANODE CAP

WARNING !!

AN ISOLATING TRANSFORMER SHOULD BE USED DURING ANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD DUE TO LIVE CHASSIS. THE CHASSIS OF THIS RECEIVER IS DIRECTLY CONNECTED TO THE POWER LINE.

SAFETY-RELATED COMPONENT WARNING !!

COMPONENTS IDENTIFIED BY SHADING AND MARKED ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION

APRES AVOIR DECONNECTE LE CAP DE’LANODE, COURT-CIRCUITER L’ANODE DU TUBE CATHODIQUE ET CELUI DE L’ANODE DU CAP AU CHASSIS METALLIQUE DE L’APPAREIL, OU AU COUCHE DE CARBONE PEINTE SUR LE TUBE CATHODIQUE OU AU BLINDAGE DU TUBE CATHODIQUE.

ATTENTION !!

AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION PROVENANT D’UN CHÁSSIS SOUS TENTION, UN TRANSFORMATEUR D’ISOLEMENT DOIT ETRE UTILISÈ LORS DE TOUT DÈPANNAGE. LE CHÁSSIS DE CE RÈCEPTEUR EST DIRECTMENT RACCORDÈ Á L’ALIMENTATION SECTEUR.

ATTENTION A UX COMPOSANTS RELATIFS Á LA

SÈCURITÈ !!

LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNE MARQUE SUR LES SCHÈMAS DE PRINCIPE, LES VUES

EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.

SECTION 1

www.ELEKO.de

GENERAL

The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain

as in the manua

Overview

This section briefly describes the buttons and controls on the TV set and the Remote Control. Open the flaps at the front and back of his Instruction Manual for detailed illustrations. For more information refer to the page numbers given in the overview.

Remote Control

Symbol Description See page

u TV: standby mode on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

1 TV

R Teletext: Freezing a subpage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Å/a

5 > PIP: Selecting the source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

´/´

7 1, 2, … 9, 0 Number buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

!¡ Joystick for menu selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

!™ MENU Switching on and off of Menu system . . . . . . . . . . . . . . . . . . . . . . . . . . 31

!£ PROGR +/– TV: Channel selection up- and downwards . . . . . . . . . . . . . . . . . . . . . 32

!¢ ¸ +/– Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

!∞

!§

!¶

-/--

!•

!ª

@º

@¡

;

@™

@£ VIDEO

u VCR: Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Buttons under cover

@¢

@∞ CH +/– VCR operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

VTR 1 2 3 4 MDP Video equipment selector 0 z ) p P r Buttons for VCR operation

@§

TV: on-screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Teletext: index page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Selecting of input source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

PIP: Swapping the screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

PIP: Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Back to the channel last selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Selecting of screen format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

No function on this set

Press OK to confirm

Teletext: Page selection up-and downwards . . . . . . . . . . . . . . . . . . . . . 42

Picture mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Equaliser mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Selection of double digit channel numbers . . . . . . . . . . . . . . . . . . . . . 32

Freezing of TV picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

No function on this set

Teletext: Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

TV: Selecting of TV mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Teletext: Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Muting of sound on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Displaying of the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Resetting of picture setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

TV-set – front and top

Symbol Description See page

B q 3 S-video input jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

C … 3,

≤

D u Indica r for ndby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

E U P wer sw h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

F … S ecting inpu ource . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

G ¸ +/– Volu c rol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

H PROGR – Channel selection up- and downwards . . . . . . . . . . . . . . . . . . . . . . 37

I CON ROL Control panel: Switching on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

3 Ph no vide /aud inp ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

F G H I

+–+

A B C

Headphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

ROGR

–

CON RO

M NLKJ

/G/SI

RD/D D

TV-set – rear

Symbol Description See page

1 21-pin Euro connector (Scart) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

2/j2 21-pin Euro connector (Scart) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

3/j3 21-pin Euro connector (Scart) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

N R/D/D/D, L/G/S/I, External speaker terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

|, |

S, | C (Centre, Surround)

O L/G/S/I

R/D/D/D

™

R/D/D/D

L/G/S/I Audio phono jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Aerial socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Left and right speaker terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

www.ELEKO.de

Installation

B Connecting the TV Set

1 Connect the TV set to the mains socket (220-240 V. AC, 50 Hz). 2a Connect a conventional aerial cable to the socket marked ˘ M on the rear of the TV set

2b Connect your Satellite Receiver to one of the Scart connectors J K L of the TV set.

When connecting a VCR to your TV set:

We recommend that you use the preset function Manual Programme Preset (page 38) to tune in the VCR signal to programme position 0.

C Inserting the Batteries into the Remote Control

Make sure to insert the batteries using the correct polarities. Dispose of exhausted batteries according to your local regulations.

VIDEO

SAT

Step 2 Basic Presetting

A The Menu System

Your TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the Remote Control to operate the menu system:

Press MENU !™ to switch the menu on and off.

•

Use “, ”, 4, $ of the joystick !¡ to select within the menu system.

•

Press OK to store.

•

When menu is switched off:

•

Press “ to return to the last menu scre n.

B Se ecting Language and Country

1 Press th ENU !™ utton.

The menu Language/Country appears on the screen.

2 h the joystick !¡ to ”. Push the joystick !¡ to $ to select the language.

Press OK !¡. The menus appear in the selected language.

3 P h the joystick !¡ to $ to select Country. Push the joystick !¡ to ”. 4 Select the country in which you will operate the TV set using $ or 4.

Select Off if you wish an automatic tuning without ACI (fast presetting with a given channel sequence). Confirm by pressing OK !¡.

•

The menu Auto Tuning appears.

anguageCount y

anguage

Count y

Select En e

Language/Country

Language

Country

Select: Enter:

Language/Country

Language

Country

Select Country:

Engish

Engl sh

Off

Czech Rep.

Con irm: OK

Eng ish

Austria

Begium

Bugaria Denmark

Finland

Off

D Switching on the TV Set

Press the switch U E at the front of the TV set.

•

If the standby mode indicator u D on the TV is lit, press TV I/u 1 on the Remote Control to switch on the TV set.

First Time Operation

C Automatic Tuning In of Channels

Push the joystick !¡ to ” for more than 2 sec..

•

After all available channels are stored, the TV goes back to the programme position with which you started the automatic tuning. Your TV is now ready for use.



To stop the automatic tuning: Press OK !¡.



If you wish to change the sequence of the stored channels, go to Sorting Programme Positions in Advanced Presetting.



If you need to change or repeat the tuning afterwards (e.g. when you move house) : select the menu Auto Tuning in the Set Up

menu.

1 2 3

Searching

CO2 CO3 CO CO7 CO8

Set Up

Auto Tuning

Programme Sorting AV Preset Instal ation

Start Au o Tuning:

Select:

First Time Operation

Start

www.ELEKO.de

Step 3 Basic TV operation

This section explains the most important functions for the daily use of your TV set. When using the control panel on the top of the TV set, first press CONTROL I, then F, G or H.

Function Operation

Switching on/off

Switching off temporarily (Standby mode) TV is now in standby mode. Indicator u D lights

Switch on from standby mode button 7.

Selecting channels

Using the Channel overview Push to $ or 4 to select a channel, push to z to

Going to the channel last selected

Adjusting the volume

Muting the sound

Selecting Equaliser mode (See also page 39) following modes: Personal, Vocal, Jazz,

Selecting Picture mode (see also page 38) of the following modes: Personal, Movie or Live.

Freezing the picture

Changing the screen format (imitation of wide screen format).

Resetting picture/sound settings to factory levels Press ? @§.

Displaying on-screen indications

Displaying the time (only when teletext is Press ˚ @¢ to switch time on or off. broadcast)

Using Teletext (see also page 42) Select a page using the number buttons 7

Viewing the input signal of a connected device source. (see also page 44) Press ; @¡ to return to the TV picture.

First Time Operation

Press U E on the TV set.

•

To save energy, we recommend to switch off the TV completely when set is not in use.

Press TV I/

•

u 1.

up. After 15 min. without any TV signal and no pressing of a button, the TV automatically goes into standby mode.

Press TV I/

u 1

, PROGR +/– !£ H or any number

Press PROGR +/- !£ H or the number buttons 7. For a double the two number buttons.

digit number first press -/-- !¶, then

Press OK !¡.

confirm.

Press 8.

•

Press ¸ + or – !¢ G.

•

Press ¤ @™ to switch sound off or on.

•

Press repeatedly !§ to select one of the

•

Rock, Pop or Flat Press repeatedly !∞ to select one

•

Press !• if you wish to make a note of an

•

information, e.g., a telephone number. Press again to return to the normal TV screen.

Press 9 repeatedly to select 4:3 or 16:9

•

Open the cover of the Remote Control.

•

2 to switch indications on or off.

Press

•

Open the cover of the Remote Control

•

Press f @º to switch on. Press ; @¡ s itch off.

•

E.g. for page 125 press 1,2 and 5. Select the index page by pressing

Press … 3 repeatedly to select the desired input

•

12 13 1

8 9

VIVA RTL SAT 1 S3 VIVA 2 PRO 7 ARD

+–+

–

Soul Music News Game Show Animal Report Stones in Interviev Pink Panther Afternoon Report

Advanced Operation

Advanced Presetting

Sorting of Programme Positions

After having used Automatic Tuning chan els y u may wish to rearrange the order of the channels.

1 Press MENU. Select the symb

sing $ h to ”.

2 Select Programme Sorting u ng $. Pus to ” to enter. 3 Select the programme positio of the channel you wish to sort using 4 or $.

Push to ” to ter.

4 Move t e channel t e new programme position using 4 or $. Store by

pressi g OK. The c nnel is now at e new position. The other programme positions move a ordingly.

5 To sort oth mme positions repeat steps 3 to 4. 6 Press MENU to return to the normal TV screen.

M nual Tuning In of Channels

Use this function to preset channels or a video input source one by one to programme positions of your choice.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position by pushing to 4 or $. Push twice to ”.

The column SYS is highlighted.

4 Select the TV system using 4 or $. Push to ” to enter.

Available TV systems are B/G for western European countries, D/K for eastern European countries, EXT for a video input source (please go to step 5c after selecting EXT) The column CH is highlighted.

5 Select your method for the channel tuning using 4 or $. Push to ” to enter.

You have the choice between C for a terrestrial channel, S for a cable channel, F for direct frequency input.

a Direct Channel Input - S, C or F

For channel numbers input a two digit number, for the channel frequency a three digit number.

Select the two or three digits by using the number buttons 0 to 9.

•

To start the search and to store the channel, press OK.

•

To preset other channels repeat steps 3 to 5a.

•

b Channel search (SEARCH)

Use Search if you do not know the channel number or frequency Start the search for the next available channel by pushing to $.

•

Store the channel by pressing OK or continue the search by pushing again to $.

•

To search for other channels repeat steps 3 to 5b.

•

c For video input sources (EXT)

Select the Video Input source using 4 or $.

•

Store your selection by pressing OK.

•

To allocate other sources repeat steps 3 to 5c.

•

6 Press MENU to return to the normal TV screen.

using $. Push to ”.

Set Up

Auto Tuning

Programme Sor ing

AV Preset Installation

Select: Enter:

Programme Sorting

PROG CH LABEL

C03

PRO 7

C05

EU- P

C07

SWF

C08

R L

C09

MDR

C 2

DDI

C 3

DSF

C 4

R L 2

C 5

KAB

C 6

Se ect Prog.: Confirm:

Programme Sorting

PROG CH LABEL

C03

C03 5

PRO 7

C05

EU- P

C07

SWF

C08

R L

C09

MDR

C 2

DDI

C 3

DSF

C 4

R L 2

C 5

KAB

C 6

Se ect Pos tion: Move: OK

Insta lation

Language/Country

Manual Programme Preset

Further Programme Preset RGB Set Up Picture Rotation Personal ID

Se ect: Enter:

Manual Programme Preset

PROGCHSYSSKIP LABEL

Se ect: Enter:

PROGOfSKIP

PROG SYSOfSKIP LABEL

1 B/G

PROG SYSOfSKIP LABEL

1 B G

ROGCHS SOSKI ABE

0 EX

B/G

B/GOfOf

SYS LABEL

B/G

D/K

EXT

First Time Operation

C09 C10

S F

AV2 AV3

- - - - - - -

ARD BBC

www.ELEKO.de

Advanced Presetting

Captioning a Station Name

During presetting the channels are usually labelled automatically. You can, however, individually name a channel or a video input source.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position of the channel or the video source you wish to

label by pushing to $ or 4. Push repeatedly to ” until the first element of the position LABEL is highlighted.

4 Select a number, a letter, + or a blank using 4 or $. Push to ” to confirm.

Select the other four characters in the same way.

using $. Push to ”.

5 Store your selection by pressing OK. 6 To label other channels or video sources repeat steps 3 to 5. 7 Press MENU to return to the normal TV screen.

Skipping of Programme Positions

In case of 100 programme positions there may be unused positions, which you can skip in the menu Manual Programme Preset. When changing channels with the PROGR +/– buttons they do then not appear. You can, however, still select them using the number buttons.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position you wish to skip by pushing to 4 or $.

Push to ” to enter. The column SKIP is highlighted.

4 Select ON using $. 5 Store by pressing OK. 6 To skip other programme positions repeat steps 3 to 5. 7 Press MENU to return to the normal TV screen.

using $. Push to ”.

Manual Programme Preset

PROG CHSYSSK P LABEL

C09

ARD

B G

Off

C10

BBC

B G

Off

Off Off

Off

Select: Enter:

PROG CHSYS

SK P LABEL

C07 TE

Off

6 B/G

Manual Programme Preset

PROG CHSYSSKP LABEL

C09

ARD

B G

Off

C10

BBC

B G

Off

Select: Ent

PROG CHSSKIP L

53 BG

9 Of

Advanced Presetting

Selecting your NexTView Provider*

*depending on availability of service

NexTView is an on-screen electronic programme guide, providing you with programme information on many broadcasters. Your TV set automatically selects a NexTView provider. This provider will be available about 30 minutes after the channel tuning. You can however, also select a provider of your choice. See Using NexTView on page 48 for information on the operation of NexTView.

When using a satellite receiver make sure to connect the receiver to the aerial socket of your TV set.

1 Press MENU. Select the symbol 2 Select Select NexTView using $ Push z o e ter.

A list is displayed containing all a ilabl exTView providers and the supported broadcasters.

using . Push z to enter.

3 Select the desired NexTView rovider by sing 4 or $. Store by pressing OK. 4 Press MENU to return to the no al TV creen.

Using of Furth r Programme Preset

Using t menu Furthe rogramme Preset you can

individu ly attenu te the strength of a channel signal in case of a strong local aerial signal (striped picture).

idually adjust the volume level of each channel.

improve the quality of a weak channel (picture or sound distortions) with manual fine tuning.

d)p eset the AV output for programme positions of those channels with

scrambled signals (e.g. from a Pay TV decoder). In this way a connected Smartlink VCR records the unscrambled signal.

Press MENU. Select the symbol

2 Select Installation using $. Push ” to enter. Select Further Programme Preset

using $. Push ” to enter.

3 Select the programme position of the desired channel by pushing 4 or $.

Push ” repeatedly to select: ATT (RF attenuator), VOL (Volume Offset), AFT (Automatic Fine Tuning) or DECODER. The selected item changes colour.

4a ATT

Push $ to select ON. Store by pressing OK. Repeat steps 3 and 4a if you wish to attenuate other channels.

b VOL

Push 4 or $ to adjust the volume level (range -7 to +7) of the channel. Store by pressing OK. Repeat steps 3 and 4b if you wish to adjust the volume level of other channels.

c AFT

Push 4 or $ to fine tune the channel (range -15 to +15). Store by pressing OK. Repeat steps 3 and 4c if you wish to fine tune other channels.

d DECODER

Push to 4 or $ to select AV1 (Euro AV socket 1) or AV2 (Euro AV socket 2) as output for the video source on this programme position. Store by pressing OK. Repeat steps 3 and 4d if you wish to preset the AV output of other video sources.

Should you use Auto Tuning afterwards, this setting will be cancelled.

5 Press MENU to return to the normal TV screen.

using $. Push ” to enter.

Channes: EURON

DRS 3SAT ARTE

VOX

Select Next View

Swiss Text

Euro News

Installation

Language/Country Manual Programme Preset

Further Programme Preset

RGB Set Up P cture Rotat on Personal ID Demo

Select: Enter:

Further Programme Preset

PROG AFTVOLATT DECODER

Select: Enter:

PROG AFTVOLATT DECODER

1 On -5

PROG AFTVOLATT DECODER

1 On -5 On

- - - - - - -

Off

5 6 7 8 9 10 11

Off

On 0

AV1 AV2

Off

Advanced Operation

Advanced Presetting

www.ELEKO.de

Advanced Presetting

Adjusting the Picture Geometry for an RGB Source

When connecting an RGB source such as a Sony playstation you may need to readjust the picture geometry.

1 Select the connected RGB source 2 Press MENU. Select the symbol 3 Select Installation using $. Push to ” to enter. Select RGB Set Up using $.

Push to ” to enter.

4 Select H Centre by pushing to ”. Adjust the centre of the picture

(range from -10 to +10) using 4 or $. Store by pressing OK.

5 Select H Size using $. Push to ” to enter. Adjust the horizontal coordinates

(range from -10 to +10) using 4 or $. Store by pressing OK.

by pressing … repeatedly.

using $. Push to ”.

6 Press MENU to return to the normal TV screen.

Adjusting the Picture Rotation

Because of the earth magnetism the picture might slant. In this case you can readjust the picture.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” to enter. Select Picture Rotation using $.

Push to ” to enter.

3 Adjust the Picture Rotation (adjusting range -5 to +5) by pushing to 4 or $.

Store by pressing OK.

4 Press MENU to return to the normal TV picture.

using $. Push to ”.

RGB Set Up H Centre

H S ze

Adjust Pos tion: Confirm: OK

RGB Set Up

H Centre

H S ze

Adjust Size: Confirm: OK

Instal ation

Language/Country Manual Programme P t Further Programme eset RGB Set Up

Picture Rota i

Personal ID

Rotate: Confirm:

Inputting Your Personal ID

You can programme your TV with a safety code, so that you can be traced if your TV is stolen and recovered. This code can only be input once!

Make sure to write it down in this Instruction Manual.

1 Press MENU. Select the symbol 2 Select Installation using $. Push to ” t enter. S ect Personal ID using $.

Push to ” to enter.

3a Select the first of a total of 11 cha ters tter, number, + or a blank) by

using 4 or $.

b Push to ” to go to the next aracter. c Repeat a and b for all charac s.

using $ Push to ”.

4 Store by pres ing OK. 5 Press MENU to retu to the normal TV screen.

Ins allat on

Language/Country Manual Programme Preset Further Programme Preset RGB Set Up Picture Rotation

Personal ID

Select A-Z, 0-9

: Store: OK

- - - - - -

Presetting and Labelling of Input Sources

1 Press MENU. Select the symbol 2 Select AV Preset using $. Push to ” to enter. 3 Select the desired AV input (AV 1, 2 or 3) using 4 or $. Push to ” enter.

After each step you have the choice between memorizing (press OK) or going to the next item (push to ”).

4 To label the source:

a Push to ” to select Label. b Select the first character using 4 or $. Push to ” to confirm. c Repeat step b to select the other 4 characters.

d Store by pressing OK. 5 Repeat steps 3 to 4 for the other AV inputs. 6 Selecting the AV3 Input Source:

In case of AV3 you have the choice between the front AV3 sockets BCor the rear Scart 3 L connector.

a Push to $ to select AV3 Input. Push to ” to enter.

b Select Front or Rear using 4 or $.

c Store by pressing OK. 7 Press MENU to return to the normal TV screen.

using $. Push to ”.

AV Preset

INPU LABEL

IDEO

A 2

IDEO

A 3

AV 3 Input Rear

Se ect: Enter:

AV Preset

NPU LABEL A

DEO

A 2

DEO

A 3

DEO

F ont

AV 3 Input

Select Mode: Confirm: OK

Rea

Advanced Operation

www.ELEKO.de

Advanced TV operation

Adjusting Picture and Sound

Picture and sound are adjusted at the factory. You can however, adjust them individually.

1 Press MENU.

Select the symbol Push to ” to enter. The menu Picture or Sound Control is displayed.

2 Select the desired item using 4 or $. Push to ” to enter. 3 Adjust the selected item using 4, $, ” and “. Press OK to store.

Refer to the tables on this and the following page for more information.

4 Repeat steps 2 and 3 to adjust other items. 5 Press MENU to return to the normal TV screen.

Picture Control Item Effect/Operation

Picture Mode $ Live (for live broadcasts)

Contrast Less “” More Brightness* Darker “” Brighter Colour* Less “” More Hue** Reddish “” Greenish Sharpness* Softer “” Sharper Reset Resets picture to the factory preset levels AI 4 Off: normal

(Artificial Intelligence) $ On: Automatic optimization of contrast level

Noise Reduction 4 Off: Normal

Digital Mode $ Normal: 100 Hz

* Only if Personal is selected in Picture Mode ** Only available for NTSC colour signal (e.g. US video tapes)

Sound Control Item Effect/Operation

Equaliser mode Select between the following sound setting

for Picture or for Sound using 4 or $.

Personal (for individual settings)

4 Movie (for movie broadcasts)

according to the TV signal

$ On: Reduces picture noise in case of a weak

broadcasting signal

Digital+: 100 Hz plus line flicker reduction

4 Advanced: Digital+ plus smoothing of motions

$ Personal

Vocal Jazz Rock Pop

4 Flat (fixed setting, cannot be adjusted)

Picture Adjustment

Picture Mode

Contrast Brightness Color Sharpness Reset AI Noise Reduct on Digi al Mode

Select Mode: Enter:

Picture Mode

Contrast

Noise Reduct

Digit ode

Aud o Adjustmen

Equa iser Mode

Equa iser Adjustment Surround Mode SRS Mode Auto Vol. Control Dual Sound Volume Dual Sound

Select Mode: Confirm: OK

Personal

Advanced

Pe sonal

Digital

Personal

SRS 2

Normal

Movie

Vocal

Mono

Advanced TV operation

Sound Control (continued) Item Effect/Operation

Equaliser adjustment

On On

Surround mode 4 Off: Norm

Live

SRS Mode* 4 SRS 1 *on when SRS l d SRS 2 in S rround mode $ SRS 3

Au Volum ntrol 4 On: volume level of the channels will stay the same

ual Sound For a bilingual broadcast:

Off

Jazz Rock

Pop Fat

SRS

Headphones

2 Volume Less “ ” More 2 Dual Sound For a bilingual broadcast:

** TruSurround is a trademark of SRS Labs, Inc. SRS and the SRS symbol are registered trademarks of SRS Labs, Inc. in the Unites States and selected foreign countries. SRS and TruSurround are incorporated under license from SRS Labs, Inc. and is protected under United States Patent Nos. 4,748,669 and 4,841,572 with numerous additional issued and pending foreign patents. Purchase of this product does not convey the right to sell recordings made with the TruSurround technology.

You can adjust the mode selected in Equaliser mode by cutting and boosting of 5 selected frequency bands. Only the changes made in Personal can be stored, the others return to factory setting. Select the desired bar using ” or “, adjust using 4

•

and $. Press OK to store

D lby Sur (Pro ogic Tru Surround **) Sele when ceiving Dolby broadcast. A ter th broa return to off, otherwise the

V autom ically selects Dolby for any stereo

oadcast an the sound will be distorted. SR Hall Church Disco

$ Stadium

independent of the broadcast signal (e.g. in case of advertisements)

$ Off: volume level changes according to the

broadcast signal

$ A for channel 1 4 B for channel 2

For a stereo broadcast:

$ Mono 4 Stereo

$ A for channel 1 4 B for channel 2

PAP When PAP is switched on, you can additionally select the PAP sound for the headphones

Equaliser Adjustment

Personal

0 –

20 50 5K 5 K 0 K

Sel: Adjust: Confirm:OK

Aud o Adjustment

Equa iser Mode Equa iser

Adjustment

Surround Mode

SRS Mode Auto Vol. Control Dual Sound Volume Dual Sound

Select Mode: Confirm: OK

SRS Mode

Auto Vol. Control

Dual Sound

Volume

Dual Sound

Dolby Su

Stadum

Chu ch

SRS 2

Ste eo

Disco

Mono

SRS 2

Mono

Hal

SRS

Advanced Operation

Advanced TV operation

www.ELEKO.de

Advanced TV operation

Using the Features Menu

1 Press MENU. Select the symbol using $. Push z to enter. 2 Select the desired menu item using $. Push z to enter. 3 Select the desired setting using 4 or $. 4 Store by pressing OK. 5 Press MENU to return to the normal TV screen.

Features Item Effect/Operation

Auto Format* 4 On: Automatic selection of the screen format *only for aerial signal $ Off: Normal mode

Format Correction* 4 On: Smart mode is selected automatically for 4:3/ *only if Auto Format is on 14:9 broadcasts

Sleep Timer

Parental Lock $ Off: Normal mode

AV2 Source

$ Off: 4:3/14:9 is selected

You can select a time period after which the TV switches itself into standby mode

4 Off

10 min. 20 min.

$ 90 min.

4 On: TV can only be switched on out of

standby-mode using the Remote Commander, the buttons on the TV do not work.

You can select the source to be output from the Scart connector record from this socket while watching another source.

4 TV audio/video signal from the aerial ˘

AV1 audio/video signal from Scart 1 AV2 audio/video signal from Scart 2

$ AV3 audio/video signal from front or rear connectors

2/j2. In this way you can

Using Multi PIP

Multi PIP (picture in picture) mode displays a succession of 12 still pictur and a 13th that is live. You can manually select which channel you wish o watch, either full-screen or in the PIP mode.

1 Press

2 Press PROGR +/- repeatedly to get the next or the preceding 12 programme

3 Use 4, $, “ and ” to move within the 13 displayed channels.

4 When the centre channel is framed, press OK to get the channel full screen or

. Now 13 programme positions appear on the screen, with th curren chann n the centre.

positions .

Press OK to select the framed channel. The selected channel moves to the centre.

to return to the normal TV mode.

press

Features

Auto Format

Format Correction Sleep Timer

Parental Lock AV 2 Source

Select: Enter:

Auto Format

Format Correction

Sleep Timer

Parental Look

AV 2 Source

03 5

01 6

11 09

10 min

AV 3 AV 2 AV

Using Screen Mode

Of Of TV

Off

When Auto Format in the Features menu is preset to »On« and a format signal is being transmitted, the TV set automatically selects the detected screen format. Screen mode, however, lets you select the screen format of your choice.

Press 9 repeatedly to get one of the f ll wing formats:

•

Smart imitation of wide screen effec or 4:3 roadcasts, parts of the top and

bottom of the pictur re cut f 4:3 conventional 4:3 aspect tio, fu picture nformation 14:9 compromise betwe 4:3 and 16:9 a pect ratios Zoom imitation of wide s reen effec or letterboxed movies Wide for 16:9 broadcasts

In Zoom and 14:9 modes parts of top and the bottom of the screen are cut off. Usi g 4 and ou can adjust the position of the image onscreen to e.g. read s btitles. Press OK to con rm.

Operating PAP (Picture and Picture)

PAP divides the screen into two for watching two channels simultaneously (with a video source on one if you want). The sound of the left screen is on the TV loudspeakers, the sound of the right screen is selectable via headphones.

Switching PAP on and off

Press

•

PAP off.

Selecting a PAP source

1 Press > 5.

The symbol > appears in the right screen.

2 Select the desired source using the number buttons (for a TV channel) 7 or

…3 (for a video source).

Swapping screens

Press

•

Zooming the screens

Using the joystick buttons “ and ” you can change the size of the two screens.

•

When you press ” repeatedly the right screen gets bigger, while the left screen gets smaller.

6 once to display the screens in format 4:3 and twice to switch

´/´

Å/a

4 to swap the two screens.

Smart

Zoom

Wide

Advanced Operation

www.ELEKO.de

Teletext

Most TV channels broadcast information via teletext. The index page of the teletext service (usually page 100) gives you information on how to use the service.

Make sure to use a TV channel with a strong signal, otherwise there may be Teletext errors.

Direct Access Functions

Switching Teletext on and off

1 Select the TV channel which carries the teletext service you want to view. 2a Press f @º once for Picture and Teletext (P&T).

The screen is divided in two, with the TV channel in the right corner and the Teletext display on the left. P&T mode: Press

TV screen. Push “ or ” to change the size of the TV screen. Press

b Press f twice to get Teletext only.

c Press f three times for Mix mode.

The TV broadcast and the Teletext display are overlapped.

3 Press

Selecting a Teletext Page

Direct Page Selection

Input the three digits of the page number using the number buttons 7.

•

If you have made a mistake: Type in any three digits, then re-enter the correct page number.

Page Catching 1 Select a teletext page which has several page numbers on it (e.g., the index

page).

2 Press OK !¡.

Page Catching is displayed.

3 Select the desired page number using 4 or $ !¡ and press OK.

The requested page is displayed after some seconds.

Selecting the next or the preceding page

Press

•

Selecting the index page

Press

•

Selecting a subpage

A teletext page may consist of several subpages. In this case an information line is displayed, showing the number of subpages. Select the mode by pushing 4. Select the subpage by using 4 or $.

•

Freezing a Teletext subpage

1 Press !• or R 3

The symbol R is displayed and the subpage is not updated.

2 Press f @º to resume normal teletext reception.

Using Fastext*

*depending on availability of service

Fastext lets you access pages with one button stroke. When Fastext is broadcast, a colour-coded menu appears at the bottom of the screen. The colours of this menu correspond to the red, green, yellow and blue buttons 9, !º, !∞, !§ on the Remote Control. Press the coloured button which corresponds to the colour in the

•

colour-coded menu.

Advanced Operation

Å/a

4. Press PROGR +/- !£ to change the channel of the

Å/a

4 again to resume normal teletext reception.

;

@¡ or press f a fourth time to switch teletext off.

!£ (Page +) or

(Page -).

100

Teletext TV

216-02

01 04 05 06 07 0802

Teletext

Using the Teletext Menu

This TV set has a menu-guided teletext system. When teletext is switched on you can use the joystick buttons to operate the teletext menu.

Select the menu functions as follows:

1 Press MENU !™.

The Teletext menu is superimposed onto the teletext display.

2 Select the teletext function using 4 or $ !¡. Push ” to enter.

Top/Bottom/Full

For convenient reading of a Tel ext pa e ou can nlarge it. After having selected the functi sub nu T p 4 Bottom $ Full OK is displayed.

Push 4 to enlarge the upper alf of the c een, push $ to enlarge the lower

•

half. Press OK to resume the n mal si e. Press f to e the normal Teletext operation.

Text Cle r

After h ving selected e function, you can watch a TV channel while waiting for a requ ted Telet xt page. As soon as the page is available, the symbol f changes colour.

f t view the page.

•

Re eal

Some teletext pages contain hidden information (e.g., for a quiz), which you can reveal. After having selected the function, the hidden information appears.

Press f to resume the normal Teletext operation.

•

Time Page*

*depending on availability of service

You can call up a time-coded page - such as an alarm page - at a time specified by you.

After having selected the function a sub menu is displayed.

1 Select On using 4 or $. Push ” to enter. 2 Enter the three digits of the desired page using the number buttons 7. 3 Enter the four digits of the desired time using the number buttons 7. 4 Press OK to store.

The time is displayed in the top left-handed corner of the screen. At the requested time the page is displayed.

Teletext

Top / Bottom / Full

Text Clear Reveal Time Page

Select: Enter Menu:

Top: Bottom: Full: OK

Time Page

PAGE TIME – – – - - : - -

Select: Enter

Advanced Operation

SECTION 2

www.ELEKO.de

DISASSEMBLY

2-1. REAR COVER REMOVAL

2 Rear Cover

CAUTION:

Take care not to damage the C Board when removing or refitting the rear cover.

2-2. CHASSIS ASSY REMOVAL

1 6 Screws BTV 4x16

2-3. SERVICE POSITION

2-4. U BOARD REMOVAL

1 Push the claw in the direction of the arrow and remove.

2 Pull the Board in the direction of the arrow and remove.

2-5. J BOARD REMOVAL

www.ELEKO.de

2-6. J SHIELD REMOVAL

1 Push the claw in the direction of the arrow and remove.

3 Remove the shield in the direction of the arrow.

2 Push the claw in the direction of the arrow and remove.

2 Pull the Board in the direction of the arrow and remove.

NOTE

All other boards are removed in a similar manner to those shown

2-7. B1 BOARD REMOVAL

2-8. PICTURE TUBE REMOVAL

www.ELEKO.de

Degaussing coils 8

Spring tension 9

C board 3

VM board 4

Neck assy 5

Deflection yolk 6

Anode cap 1

7 DGC holder

2 Chassis assy

10 Four PT screws

Picture tube 11

Cushion

• REMOVAL OF ANODE-CAP

Note : Short circuit the an de of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the CRT, after removing the anode.

* REMOVING PROCEDURES.

Anode button

Turn up one side of the rubber cap in the direction indicated by the arrow a

• HOW TO HANDLE THE ANODE-CAP

2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b

3 When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c

1 To prevent damaging the surface of the anode-cap do not use sharp materials. 2 Do not apply too great a pressure on the rubber, as this may cause damage to

the anode connector.

3 A metal fitting called a shatter hook terminal is fitted inside the rubber cap.

Do not turn the rubber foot over excessively this may cause damage if the shatter hook sticks out.

REMOVAL AND REPLACEMENT OF THE MAIN-BRACKET

www.ELEKO.de

BOTTOM PLATES.

For safety reasons, on no account should the plates be

removed and not refitted after servicing.

(1) REMOVING THE PLATES

In the event of servicing being required to the solder side of the D Board printed wiring board, the bottom plates fitted to the main chassis bracket require to be removed. This is performed by cutting the gates with a sharp wire cutter at the locations indicated by arrows.

Note :There are 4 plates fitted to the main bracket and secured by 4 gates.

Only remove the necessary plate to gain access to the printed wiring board.

(2) REFITTING THE PLATES

Because the plates differ in size it is important that the correct plates are refitted in their original location.

Please note that the plates need o be rotated 180 degrees from the cut position to allow the tabs to be fitted in the catch po itions.

Catch

Tab

SECTION 3

www.ELEKO.de

SET-UP ADJUSTMENTS

• When complete readjustment is necessary or a new picture tube is installed, carry out the following adjustments.

• Unless there are specific instructions to the contrary, carry out these adjustments with the rated power supply.

• Unless there are specific instructions to the contrary, set the controls and switches to the following settings:

Contrast ............... normal

Brightness ............... normal

3-1.BEAM LANDING

Preparation:

1. In order to reduce the influence of geomagnetism on the set’s picture tube, face it in an easterly or westerly direction.

2. Switch on the set’s power and degauss with the degausser.

(1) Adjustment of Correction Magnet for Y-Splitting

Axis

1. Input a crosshatch signal from the pattern generator.

2. Set the Picture control to minimum and confirm that he Brightness control is set to normal.

3. Position the neck assembly as indicated in Fig 3-2.

4. Move the deflection yolk as far forward as is possible.

5. Adjust the upper and lower pin symmetrically by opening or closing the Y-splitting axis correction magnets locat d on the neck assembly.

6. Return the deflection yolk to its origin l pos tion.

Carry out the following adjustments in this order:

3-1. Beam Landing 3-2. Convergence 3-3. Focus 3-4. White balance

Note: Test equipment required

1. Color bar/pattern generator.

2. Degausser.

3. Digital multimeter.

4. Oscilloscope.

(2) Landing

Note :Before carrying out the following adjustments

adjust the magnets as indicated below [See Fig.3-3].

1. Input an all-white signal from the pattern generator. M ximize the picture setting and adjust the Brightness setting

2. Rough-adjust the focus an d horizontal convergence.

3 Loosen the deflection yolk screws and align the purity

adjustment knob to its central position. [See Fig.3-1].

4. Switch from the all-white pattern to an all-green pattern.

5 Move the deflection yolk backwards and adjust with the

purity magnet so that the green is at the centre and it aligns symmetrically . [See Fig.3-4].

6. Move the deflection yolk forward and adjust so that the entire screen becomes green.

7. Switch the raster signal to red, then to blue and verify the landing condition.

8. When the position of the deflection yolk has been determined, fasten the deflection yolk with the screw.

9. If the beam does not land correctly in all the corners of the screen, use magnets to correct it. [See Fig.3-5].

Y-splitting axis correction magnet

Align Pips on each

magnet

Purity

Caution :

High voltages are present on the Deflection yolk terminals - take care when handling the Deflection yolk whilst carrying out adjustments.

Deflection yoke

Fig.3-1

Align the bottom edge of the neck assy with the G3 hole centre.

Fig.3-3

Neck assy

Fig.3-2

GREEN

www.ELEKO.de

Center dot

RED

BLUE

Fig.3-4

Disk magnets or rotatable disk

Purity control corrects this area.

Deflection yoke positioning corrects these areas

magnets correct these areas (a-d).

• If the horizontal dots are unable to coincide with the variable

H.STAT

convergence

control

H.STAT convergence

range of the H.STAT convergence, adjust together with the V.STAT convergence while tracking. [Adjust the convergence by tilting the V.STAT convergence or by opening and closing the V.STAT convergence.]

(Open)

V.S TAT

vertical static magnet

H.STAT VR on

mount side RV5376

Screen (G2)

(Close)

Fig. 3-5

3-2.CONVERGENCE

(1) Screen centre convergence

[Static convergence]

1. Input a dot signal from the pattern generator. Normalize the picture setting.

2. [Moving horizontally], adjust the H.STAT control so that the horizontal red, green and blue dots coincide at the centre of the screen.

3. [Moving vertically], adjust the V.STAT magnet so that the vertical red, green and blue dots coincide at the centre of the screen.

4. Movement of the red, green and blue dots by tilting the V.STAT magnet and by opening or closing the V.STAT magnet.

a). By opening or closing the V.STAT magnet, the red, green and

blue dots move as indicated below.

B G

b). By rotating the V.STAT magnet counter

clockwise, the red, green and blue dots move as indicated below.

B G

c). By rotating the V.STAT magnet clockwise, the red, green and

www.ELEKO.de

blue dots move in the direction indicated below.

HAMP

d). By opening or closing the V.STAT magnet, the red, green and

blue dots move in the direction indicated below.

Note : If the blue dot does not coincide with the red and

green points correct the points by using the BMC [Hexapole] magnet.

5. Correction for HMC [horizontal mis-convergence] and VMC [vertical mis-convergence] by using the BMC [Hexapole] magnet.

a). HMC correction by BMC [Hexapole] magne and movement

of the electron beam.

HMC correction(A) HMC correc ion(B)

A < B

RG B

A > B

RGB

7. HTIL correction can be performed by adding a THL correction ASSY to the DY.

TLH correction Assy

4-057-714-01

HTIL

A = B

RG B

b). VMC correction by BMC [Hexapole] magnet and movement

of the electron beam.

VMC correction(A) VMC correction(B)

C < D

C = D C > D C = D

R G

A = B

R G

RG B

Layout of each control

www.ELEKO.de

3-3.FOCUS

Purity magnet BMC (Hexaploe) magnet

V STAT convergence magnet Y-splitting axis correction magnet

Fig 3-5

Note : If you are unable to adjust the corner convergence

properly , this can be corrected with the use of permalloys.

1. Receive a television broadcast signal.

2. Normalize the picture setting.

3. Adjust the focus control located on the flyback transformer to obtain the best focus at the centre of the screen. Bring only the centre area of the screen into focus, the magenta-ring appears on the screen. In this case, adjust the focus to optimize the screen uniformly.

FOCUS

Permalloy Assy X-4387-214-1

a-d: screen-corner convergence defect

3-4.SCREEN (G2), WHITE BALANCE

[Adjustment in the service mode using the remote commander]

G2 adjustment (RV5376)

1. Input a dot signal from the pattern generator.

2. Set the Picture, Brightness and Colour to minimum.

3. Apply 175V DC from an external power supply to the R, G and B cathodes of the CRT.

4. Whilst watching the picture, adjust the G2 control RV5376 [SCREEN] located on the C Board to the point just before the flyback return lines disappear.

Convergence adjustment with permalloy

White balance adjustment for TV mode

www.ELEKO.de

Backend

1. Input an all-white signal.

2. Enter into the Service Mode by pressing ‘TEST’, ‘TEST’ and ‘MENU’ ‘MENU’on the Service Commander.

3. Select ‘Backend’ from the on screen menu display and press ‘OK’.

4. The ‘Backend’ menu will appear on the screen.

5. Set the contrast to MAX.

6. Set the ‘R DRIVE’ to 41.

7. Adjust the ‘G DRIVE’ and ‘B DRIVE’ so that the white balance becomes optimum.

8. Press the ‘OK’ button to write the data for each item.

9. Set the contrast to MIN.

10. Set the ‘R CUT-OFF’ to 31.

11. Adjust the ‘G CUT-OFF’, and ‘B CUT-OFF’ with the left and right buttons on the remote commander so that the white balance becomes optimum.

12. Press the ‘OK’ button to write the data for each item.

No Descr. Def Min Max Data

1R-on ONOFFON ON 2G-on ONOFFON ON 3 B-on ON OFF ON ON 4 D-col OFF OFF ON ON 5Color-axis 2032 6Contrast 6306363 7Limit-Luv 3033 8Hue 3106331

9Colour 3106328 10CTI -Level 2032 11 Brightness 31 0 63 31 12Gamma 2032 13 Sharpnes 31 0 63 44 14LTI-Level 0030

5 R-Drive 41 0 63 40 6 BLK-Bottom 0030

7G-Drive 4106338 18ABL-TH 0030 19 B-Drive 41 0 63 21 20ABL-Mode 2032 21 Sub Bright 31 0 63 32 22VM-Level 2032 23 R-Cutoff 31 0 63 41 24Preover 2032 25 G-Cutoff 31 0 63 45 26DPIC-Level 2032 27 B-Cutoff 31 0 63 48 28DC-Tran 1031 29 Sub-Cont 7 0 15 7 30 LRGB2-Lvl 12 0 15 12 31 P-Abl 15 0 15 15 32 DL-Pass OFF OFF ON OFF 33 Sharp.Fo ON OFF ON ON 34 Aging-W OFF OFF ON OFF 35 Aging-B OFF OFF ON OFF 36 CB-offset1 7 0 15 7 37 CR-offset1 7 0 15 7 38 CB-offset2 7 0 15 7 39 CR-offset2 7 0 15 7 40 Sub Colour 0 -8 8 -1

SECTION 4

www.ELEKO.de

CIRCUIT ADJUSTMENTS

4-1.ELECTRICAL ADJUSTMENTS

Service adjustments to this model can be performed using the supplied Remote Commander RM-891.

HOW TO ENTER INTO SERVICE MODE

1. Turn on the main power switch of the set while pressing PROG + (plus) and PROG - (minus) buttons on the top panel.

PROGR

–

2. "TT" will appear in the upper right corner of the screen.

3. Press the ‘MENU’ button twice on the remote commander to obtain the service menu on the s reen.

–

CONTROL

SERVICE MENU

Initialising Reset Devices Monitoring

ackend Defl ction Dynamic Convergence

RESET DEVICES

Backend Deflection Dynamic Convergence Colour Decoder 1 Colour Decoder 2 Feature Box PIP Sound

4. Push the joystick up or down on the remote commander to select the adjustment item.

5. Push the right button to proceed to the next menu.

6. If the required adjustment item is ‘Deflection’, push the down button to move to ‘Deflection’.

7. Push the joystick to the right to enter into ‘Deflection’.

8. Change the data in order to comply with each standard.

NOTE:

• Before performing any adjustments assure that the correct model has been selected in the Model Setting menu.

• After carrying out the service adjustments, to prevent the customer accessing the Service Menu switch the TV set OFF and then ON.

Colour Decoder 1 Colour Decoder 2 Feature Low - End PIP Special Adjustment

Select :

Next Menu

INITIALISING

Model Setting Basic Setting Feature Setting

MONITORING

Device Status monitor Error Monitor Production Monitor NVM Monitor Line 23 Monitor

Model Setting

www.ELEKO.de

Backend

1 KV-29FX60A/D/E 2KV-29FX60B 3KV-29FX60U 4 KV-29FC60A/D/E 5 KV-29FC60B 6 KV-29FC60K 7 KV-29FC60R 8 KV-29FS60A/D/E

9KV-29FS60B 10 KV-29FS60K 11 KV-29FS60R 12 KV-28/32FX60A/D/E 13 KV-28/32FX60B 14 KV-28/32FX60K 15 KV-28/32FX60R 16 KV-28/32FX60U 17 KV-29FS60A/D/E 18 KV-29FS60B

Fig.4-1

Basic setting

No Descr. Min Max Data

1 Sys.B/G OFF ON ON 2 Sys.D/K OFF ON ON 3Sys.L OFFON ON 4 Sys I (UK) OFF ON OFF 5 Sys I (IRL) OFF ON OFF 6 Russian sound OFF N OFF 7 TXT Nod.option 1 4 3 8 simple PAT OFF ON OFF

9 16:9 CRT OFF ON OFF 10 Sub-woofer OFF ON ON 11 Auto stand-by OFF ON ON 12 comb-filter OFF ON OFF 13 Auto YC det OFF ON ON 14 Auto comb det OFF ON OFF 15 AV2 Available OFF ON ON 16 AV3 Available OFF ON ON 17 AV4 Available OFF ON OFF 18 AV3 Front & rear OFF ON ON 19 SECAM Tape OFF ON OFF

No Descr. Def Min Max Data

1R-on ONOFFON ON 2G-on ONOFFON ON 3 B-on ON OFF ON ON 4 D-col OFF OFF ON ON 5Color-axis 2032 6Contrast 6306363 7Limit-Luv 3033 8Hue 3106331

9Colour 3106328 10CTI -Level 2032 11 Brightness 31 0 63 31 12Gamma 2032 13 Sharpne s 31 0 63 44 14LTI-Level 0030

5 R Drive 41 0 63 40

6 BLK-Bottom 0030 17G-Drive 4106338 18ABL-TH 0030 19 B-Drive 41 0 63 21 20ABL-Mode 2032 21 Sub Bright 31 0 63 32 22VM-Level 2032 23 R-Cutoff 31 0 63 41 24Preover 2032 25 G-Cutoff 31 0 63 45 26DPIC-Level 2032 27 B-Cutoff 31 0 63 48 28DC-Tran 1031 29 Sub-Cont 7 0 15 7 30 LRGB2-Lvl 12 0 15 12 31 P-Abl 15 0 15 15 32 DL-Pass OFF OFF ON OFF 33 Sharp.Fo ON OFF ON ON 34 Aging-W OFF OFF ON OFF 35 Aging-B OFF OFF ON OFF 36 CB-offset1 7 0 15 7 37 CR-offset1 7 0 15 7 38 CB-offset2 7 0 15 7 39 CR-offset2 7 0 15 7 40 Sub Colour 0 -8 8 -1

Fig.4-3

Fig.4-2

NOTE:

The above table is dependant on model, destination & size.

Feature setting

www.ELEKO.de

Deflection

No Descr. Min Max Data

1PIP OFFON ON

Fig.4-4

Colour Decoder 1

No Descr. Def Min Max Data

1 DelayLinMd OFF OFF ON OFF 2Gain set 1031 3 Y-Delay 7 0 15 7 4Phase Time 0030 5 Vid Ident Md OFF OFF ON OFF 6 Sync Mode OFF OFF ON OFF 7 Vid Ident Sw ON OFF ON ON 8 H-Output OFF OFF ON OFF

9 Enagating OFF OFF ON OFF 10 IF Circuit ON OFF ON ON 11 GP Delay OFF OFF ON OFF

No Descr. Def Min Max Data

1 V-Size 31 0 63 34 2V-Position 3106321 3V-Comp 1031 4 V-Linear 7 0 15 7 5S-Corr 7 0158 6 H-Size 31 0 63 29 7 EW-DC OFF OFF ON OFF 8 Pin-Amp 31 0 63 36

9Up-Cpin 3106335 10M-Pin 2032 11 Lo-Cpin 31 0 63 37 12 Trapezium 7 0 15 7 13 H-Positon 31 0 63 25 14 AFC-B w 7 0 15 7 15 A C-Angle 7 0 15 9 16 Up Vlin 0 0 15 0 17 L Vlin 0 0 15 0

Fig.4-7

Fig.4-5

Colour Decoder 2

No Descr. Def Min Max Data

1 DelayLinMd OFF OFF ON OFF 2Gain set 031 3 Y-Delay 7 0 15 7 4Phase Time 0030 5 Vid Ident Md OFF OFF ON OFF 6 Sync Mode OFF OFF ON OFF 7 Vid Ident Sw ON OFF ON ON 8 H-Output OFF OFF ON OFF

9 Enagating OFF OFF ON OFF 10 IF Circuit ON OFF ON ON 11 GP Delay OFF OFF ON OFF

Fig.4-6

Dynamic Convergence

No Descr. Def Min Max Data

1 Range 63 0 63 32 2 H Stat 33 0 63 33 3 H amp L 37 0 63 37 4 H amp R 36 0 63 36 5Up Y 3106331 6Low Y 3306333 7Y Up L 3006330 8Y Up R 3006330

9Y Low L 3106331 10 Y Low R 30 0 63 30 11Mbow Up L 3106331 12Mbow Up R 3206332 13 Mbow Low L 32 0 63 32 14 Mbow Low R 32 0 63 32 15 V Stat 32 0 63 32 16 Linearity 128 0 255 104 17 H Centre 32 0 63 32 18 H Trap 32 0 63 32 19 Rotation 0 0 255 0 20 Focus Phase 128 0 255 128

Fig.4-8

Feature Low-End

www.ELEKO.de

Feature Low-End(Cont.)

No Descr. Def Min Max Data

1 F.S.F.M OFF OFF ON OFF 2 G-Mode OFF OFF ON OFF 3 Picture Pos 0 0 3 0 4 Comp Mode OFF OFF ON OFF 5 CompSW OFF OFF ON OFF 6 Acqu.freq OFF OFF ON OFF 7 Still Pic OFF OFF ON OFF 8 Init OFF OFF ON OFF

9 Dis Feature ON OFF ON ON 10 Dis Vlimit ON OFF ON ON 11 Scr Fade 0 0 3 0 12 Hwe Delay 20 0 255 20 13 Auto Vshift OFF OFF ON OFF 14 Vwe Delay 0 0 127 0 15 SFR sw OFF OFF ON OFF 16IPQ 0030 17 D.Col Dec OFF OFF ON OFF 18 Blankfield 0 0 15 0 19 P1.5 OFF OFF ON OFF 20 P1.4 OFF OFF ON OFF 21 P1.3 OFF OFF ON OFF 22 P1.2 OFF OFF ON OFF 23 P1.1 OFF OFF ON OFF 24 Set Vdba OFF OFF ON OFF 25 Set Sidep ON OFF ON ON 26 Set Hwe OFF OFF ON OFF 27 Set Clv OFF OFF ON OFF 28 Set Hddel OFF OFF ON OFFF 29 Set Hblnd OFF OFF ON OFF 30 Set Hre ON OFF ON ON 31 Set Hbda ON OFF ON ON 32 Set Hdav ON OFF ON ON 33 Vbdasta 0 0 255 0 34 Vsdasto 0 0 255 0 35 Msbhwesto OFF OFF ON OFF 36 Msbhwesta OFF OFF ON OFF 37 Msbvbdasto OFF OFF ON OFF 38 Msbvbdasta OFF OFF ON OFF 39 Hdavsta 40 0 255 40 40 Hdavsto 255 0 255 255

No Descr. Def Min Max Data

41 Hbdasta 223 0 255 223 42 Hbdasto 222 0 255 222 43 Hresta 38 0 255 38 44 Hresto 202 0 255 202 45 Hblndsta 31 0 255 31 46 Hblndsto 30 0 255 30 47 MsbHblndsta OFF OFF ON OFF 48 MsbHblndsto OFF OFF ON OFF 49 Msb Hresto ON OFF ON ON 50 Msb Hresta OFF OFF ON OFF 51 Msbhbdasta ON OFF ON ON 52 Msbhbdasto ON OFF ON ON 53 Msbhdav to ON OFF ON ON 54 Msbhdavs a OFF OFF ON OFF

5 Hddel 0 0 15 0

Clvsta 0 0 255 0

7 Clvsto 9 0 255 9 58 Hwesta 44 0 255 44 59 Hwesto 208 0 255 208 60 Ex-Thres OFF OFF ON OFF 61 Wes ON OFF ON OFF 62 Demo mode ON OFF ON OFF 63Limerick NR 0040 64 Nthr 0 0 255 2 65 Wval 200 0 255 200 66 Agc Ych 203 0 255 203 67 Agc Uvch 209 0 255 209 68 Aal-Bypass OFF OFF ON OFF 69 Stby Fr OFF OFF ON OFF 70 Lsb Agc-Uv OFF OFF ON OFF 71 Lsb Agc-Y OFF OFF ON OFF 72Vcl cor 0030 73Ucl cor 0030 74Uv cor mode 0030 75Uvcl tau 3033 76Uvcol Lvl 0030 77 Fil Mem OFF OFF ON OFF 78Overl Thr 1031 79Y delay f 4074 80 Dcti pdxsel ON OFF ON ON

Fig.4-9

+ 65 hidden pages