Contents
Preface
This section tells you about special features,
safety information, and preparatory
information for using this manual.
Chapter 1: Setting Up
This section shows you the steps
necessary for installing and presetting for
TV, and how lo connect optional video and
audio equipment.
Chapter 2: _Llsing Basic Features
This section 9ives you basic information
about operating and adjusting your TV.
Chapter 3: Using Advanced
Features
This section ,,;hews you how to use Picture-
in-Picture, pre-programmed Remote
Commander and other useful features.
l 'iHitro ColorTV
Opiating Instructions
Before operating your TV, please read this manual
thoroughly and retain it for future reference.
KV-27TS29
KV-27TS32
KV-27TS36
KV-32TS36
KV-32TS46
KV-2970M
Owner's Record
The model and serial numbers are located at the rear of
the TV. Iqecord these numbers in the spaces provided
below. Refer to them 'whenever you call upon your Sony
dealer regarding this product.
KV-27TW77
KV-27TW78
KV-32TW77
KV-32TW78
KV-2975M
Appendix
This section !jives you specifications and
troubleshooting information.
. For a detailed table of contents, see
page 3.
Model No. Serial No.
© 1993 by Sony Corporation
WARNING Precautions
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
• Operate the TV only on 120 V AC.
• One blade of the plug is wider than the other for safety
purposes and will fit into the power outlet only one way. If
you are unable to insert the plug fully into the. outlet,
contact your dealer.
• Should any liquid or solid oJojectfall into the cabinet,
unplug the rv and have it checked by qualified personnel
before operating it any further.
• Unplug the TV from the wall outlet if you are not going to
use it for several days or more. To disconnect the cord,
pull it out by the plug. Never I:ull the cord itself.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to
the presence of uninsulated "dangerous
voltage" within the product's enclosure that
may be of sufficient magnitude to constitute
a risk of electric shock to persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
TO PREVENT ELECTRIC SHOCK. DO NOT USE THIS
POLARIZEr) AC PLUG WITH AN EXTENSION CORD.
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
Note to CA'IV system installer
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
• To prevent internal heat build.up, do not block the
ventilation openings.
• Do not install the TV in a hot c_rhumid place, nor in a
place subject to excessive dust or mechanical vibration.
Clean the TV with a soft dry cloth. Never use strong
solvents such as thinner or ben;:ine which might damage
the finish of the cabinet.
Keep the original carton and packing materials to use for
safe transport of your TV in the future.
If you have any questions or problems concerning your TV,
please contact your nearest Sony dealer.
For details concerning safety pr.=cautions, see the supplied
leaflet "IMPORTANT SAFEGUARDS."
_'o_:1.Ujlli[o]_lq
When using TV games, computers, and similar products
with your TV, keep the brightne=;s and contrast functions at
low settings. If a fixed (non-moving) pattern is left on the
screen for long periods of time at a high brightness or
contrast setting, the image can be permanently' imprinted
onto the screen. These types of imprints are not covered by
your warranty because they are the result of misuse.
Use of this television receiver for other than private viewing
of programs broadcast on UHF or VHF or transmitted by
cable companies for the use of the general public may
require authorization from the broadcaster/cable company
and/or program owner.
Preface
This television receiver provide.,; display of television closed
captioning in accordance with § 15.119 of the F-CC rules.
TatlleofContents
Preface
Warnirtg/Precautions ........................................................... 2
Introducing the Sony Trinitron _ Color TV_............................ 4
Chapter 1: Setting Up
Connecting TV Antenna/Cable .......................................... 12
Using the On-Screen Menus ............................................. 14
Changing the menu language ....................................... 16
Turning the Cable IVlode On or Off .................................... 17
Presetting TV Channels ..................................................... 18
Chapter 2: Using Basic Features
Watching TV Programs ..................................................... 29
Using Convenient Features ............................................... 30
Mu':ing the sound- MUTING ........................................ 30
Keeping the displays on-screen
- DISPLAY ............................................................... 30
Setting the sleep timer- SLEEP .................................. 30
Chapter 3: Using Advanced Features
Watching Two Pict_res at Once
(Picture-in-Picture) ........................................................ 38
Using the Timer-Activated Functions ................................. 44
Setting the clock - CURRENT TIME SET .................... 44
Sel:ting the ON/OFF TIMER .......................................... 46
SelIing CHANNE-L BLOCK ........................................... 48
Identifying your TV ........................................................... 4
Locating the Controls ............................................................ 6
Connecting Other Equipment ............................................ 22
Video equipment ........................................................... 22
Audio system .................................................................. 26
Watching a video with your S video-equipped VCR ..... 28
Switching quickly between
two channels - JUMP .............................................. 30
Using Closed Caption ........................................................ 31
Adjusting Picture and Sound Quality .................................. 32
Adjusting the picture ...................................................... 32
Adjusting the sound ....................................................... 34
Customizing the Screen Display ......................................... 50
Setting channel captions - CH CAPION .................... 50
Viewing the captioned channels - CH GUIDE .............. 52
Setting VIDEO LABEL .................................................. 53
Using the Pre-Programmed
Remote Commander .................................................... 55
Appendix
Specifications ..................................................................... 58
Troubleshooting .................................................................. 59
Preface 3
IntroducingtheSonyTrinitron®ColorTV
This manual covers 11 different models. The menu
displays are based on model KV-32TS36, one of the models
with the most functions, and the Remote Commander
illustrations are based on RM-Y118. If a particular function
With the following features, you can:
• Receive up to 125 cable channels for a total of 181
possible off-air cable channels with the multi-band VHF/
UHF/CATV tuner.
• Receive the picture and sound of your VCR through the
VIDEO IN jacks.
• Receive superior VCR playback pictures when you
connect a VCR equipped with an S video output jack to
the S VIDEO IN Jack.
• Watch your portable camera images (8mm, video, etc.) by
connecting to the VIDEO IN jacks on the front panel.
• Receive stereo programs and Second Audio Program
(SAP) broadcasts with the built-in Multlchannel TV
Sound (MTS) decoder.
• Receive TV or video sound through an audio system by
connecting to the VARIABLFJFIX AUDIO OUT jacks.
• Simulate the sound quality of a concert hall or movie
theater with t_heSURROUND system.
• Watch another TV channel, video or cable image as a
window picture by using Picture-in-Picture.
does not apply to your model, this will be noted in the
manual.
We highly recommend that you read this manual before
using your TV. Keep the manual h_'mdyfor future reference.
• Automatically preset all receivable channels with AUTO
PROGRAM.
• Watch the closed caption and th,) text by using Closed
Caption.
With the supplied Remote Commmander,you c.an:
• Operate theTV, plus Sonyand most othermaker's video
equipmentorSony multidiscplayerwiththePre-
Programmedfeature.
• SwitchquicklybetweentwochannelsbyusingJUMP.
• Set theTV to automaticallyshut offafterdesiredtime (30,
60, 90 minutescan beset) usin_ltheSLEEP timer.
• Set theinternalclockto displaylhe CURRENTTIME on-
screen.
And enjoy other features giving you a high quality
picture...
• Colorpure Filte¢ u produces fine picturedetailwithout
colorspill orcolornoise.
• The New DynamicPicture TM systemadjustspicture
contrastautomaticallytoproduc_moredetailin both
brightanddarkareasof everyscene.
Check the model number of your set.
There are slight differences among 11 models covered
by this manual.
]able of models
YES: equipped
HO: not equipped
Picture-in-Picture feature
Pre-Programmed feature
Front panel A/V jacks
S VIDEO IN jacks
Remote Commander
Model destlnatlon U.S.A./Canada U.S.A./ U.S.A.
Closed caption YES* YES YES
Dual language NO YES NO
Check the table below to see whal your TV is eqtJipped with
before you start operating it.
NO NO YES
NO YES YES
YES YES YES
NO YES YES
NO YES YES
RM-Y116 RM-Y117 RM-Y118
Canada
Cenlral South
America and
other area
NO
YES
*U.S.A. models only
Z$ Preface
KV-27TS29 KV-32TS36
KV-27TS32 KV-32TS46
KV-27TS36 KV-2975M
KV-2970M
KV-27TW77 (Natural wood fir_ish)
KV-27TW78 (Black)
KV-32TW77 (Natural wood finish)
KV-32TW78 (Black)
F-'_
u_
=3"
CD
<=
--I
co
RM-Y118
tl_ _zJ _J I
_J
RM-Y117
E
Q ®_)l
G
d
c
RM-Y116
® _,)®
r _r
_.._j
Preface 5
LocatingtheControls
For details, see the pages indicated by the numbered black circles O.
- - -- Main picture input mode
...... - ! ! i Chanrel number display
i_) - _) t_ t_)On-screen menu-l_)displays __-- _)CHANNELSLEEP,___,)MUTINGCAPTIONdisplaysdisplay_)
I I - - ." MTS mode (MAIN, SAP or
Bar display for volume, II .i II
picture or sound adjustment • - . - i ,_ Picture-in-Picture inpu,t mode
• • -• II-I__i_/i_l- 11 (KV-2?TS36/32TS36/32TS46/
CURRENT TIME
, i l I .i i i 27-DN77/27TW78/32TW77/
display
- ......... I 32TW78 only)
i
KV-32TS36
(The screen display,;, except for certain features
as noted above, are th_ same for all models.)
1 Preface
KV-27TS29
KV-2970M
KV-2TrS32 KV-27TS36
KV-32TS36 KV-32TS46
KV-2975M
KV-2TIW77 KV-32TW77
KV-27TW78 KV-32TW78
E
I
AV input jack door
operatio_,_\
Pull the
door open
DEMO TV/VIDEO - VOL
[
)CD IC._
TV!VIDEO button*
DEMO button**
Remote control detector
,.EL÷O WE"I ]
|1 TIMER/STAND BY indicator
CHANNEL +/- buttons*
VOLUME +/- buttons*
STEREO indicator
POWER button*
I DEMO TV/VIDEO - VOL
c_ IC--
TV/VlDEO button*
DEMO button**
Remote control detector
OPOWER I /
INEL+ , /-_ .41 STEREO I I_ VII_ EO 2JINPUT
VOLUME +/- buttons*
CHANNEL +/- buttons*
i u _,-_ -_
VIDEO :2/I
I ITIMER/STAND BY indicator'
I STEREO indicator
POWER button*
* Buttons with the same function are
also located on the Remote
Commander (pp. 10 - 11).
** Ifyou press this button, functions
and menues are displayed one by one.
Press any button to stop DEMO.
Preface
7
Locatingthe Controls
VHF/UHF
antenna terminal
KV-2TTS29 KV-2970M
VHIF/UHF
®
VIDEO 1 IN jacks
-q
KV-27"TS36 KV-32TS36 KV-27TW77
KV-27-rw78 KV-32TW77 KV-32TW78
KV-2975M
VHF/UHF
antenna terminal--
S VIDEO IN jack
VIDEO 1 IN jacks
VIDEO 3 IN jacks ----7
KV-27TS32
VHF/UHF
antenna terminal-
S VIDEO IN jack
---AUDIO OUT jacks
IN
-- swor=o
mR
AUDIO OUT jacks
VIDEO 3 OUT jacks
Preface
VIDEO 1 IN jacks
VIDEO 3 IN jacks
AUX (auxiliary) terminal
TO CONVERTER terminal_
S VIDEO IN jack
VHF/UHF antenna terminal
VIDEO 1 IN jacks
KV .32TS46
AUDIO 04JT
AUDIO OUT jacks
'--VIDEO 3 IN jacks
-- AUDIO OUT jacks
ii i
0 Bottom Hinge _ 1
2_
0 Top Hinge _ 1
Screw 4 x 4 OD I 4
'_ I ....... 1 -t !
Push here to close.
To open, push again.
Check that the projection of
the screw through the hinge
a.llows for proper installation
of the hinge to the glass,
tlnen insert the bottom hinge
0 into the bushing located
on the cabinet bottom.
_____.__ _mporary
shelf
support
/
O Metal pin _ 4
0 Plate pad _ 1
0 Push plate _ 1
Press the upper part of the
temporary shelf supports
while pulling shelf in
opposite direction and
detach the shelf, insert the
metal pin shelf supports
and, aligning the grooves
with the supports, insert
the shelf.
_/"_ / shelf
';_.__!:=_"_/'i support
Temporary
Attach the top hinge 0 to
one end of the glass door,
and tighten the screws.
Attach plate pad 0 to the
other end then push plate
over the plate pad.
[ _\,
,/I
Pushing the glass door
hin up into the hole
locate:] on the cabinet
cet slide the door into
the bcttom hinge, then
tighten the screws.
/.._.
Check projection of this
area of screw "7
I
Coated side
Align the grooves with 0
LocatingtheControls
For details, see the pages indicated by the numbered black circles O.
MUTING button 1_)
TV button _*
TV/VIDEO button*
DISPLAY button _) _)
CH GUIDE button !_)
JUMP button l_)
CODE SET button 1_)
(Pre-Programmed
function)
WN]DEO (_
®®®1
®®®t
VOL CH
CHGUIDE
JUMP
CODESET
CH AUDIO
SLEEP button (_)
POWER button _ (_) (_) l_)
CABLE POWER button
0 - 9 buttons
CHANNEL GUIDE directory keys _)
ENTER button _)
CH (channel) +/- scan button _`
VOL (volume) +/- button • !_)
CABLEBOX-'I'V selector _)
Menu buttons
@-@_)@-@_)-@
Picture-in-Piclure buttons _" (_) - _)
Video operating buttons
@
REC • TV/VTR
RM-Y118:KV-27TS36 KV-32TS36
KV-32TS46 KV-27TW77
KV-27TW78 KV-32TW77
KV-32TW78 KV-2975M
(RM-Y117: KV-27TS32)
* Buttons with the same function are
also located on the TV (p. 7).
** Buttons not included on RM-Y117
FtF_
If the CABLEBOX-TV selector is set to
CABLEBOX the Remote Commander is able
to control a connected cable box, not the TV.
Set the selector to TV to control the TV set
with the Remot=_ Commander (You can use
POWER button at any case).
0 Preface
SLEEP button 1_)
MUTING button (_)
rv/VIDEO button*
DISPLAY button _) _)
CH GUIDE button _)
JUMP button (_)
RM-Y116:KV-27TS29
KV-2970M
POWER button* (_) (_) (_)
0 - 9 buttons
CHANNEL GUIDE directry keys (_)
ENTER button _)
CH (channel) +/- scan button*
VOL (volume) +/- button* (_)
Menu buttons
e)-6)@@-e e)-e)
* Buttons with the same f_Jnction are
also located on the TV (p. 7).
WARNING
Batteries may explode i: mistreated. Do
not recharge, disassem31e, or dispose of
in fire.
=,-&-
==
=_,
Installing Batteries
1 R:mmpVr tZee )caott:ll(R!ar of commander
Remove the battery
compartment cover.
(Rear of commander'
Insert two size AA (R6)
batteries in correct polarity.
Insert a size AA (R6) battery
in correct polarity.
Battery life
With normal operation, batteries will last up
to half a year. If the Remote Commander
dose not operate properly, the batteries
might be exhausted. Replace both of them
with new ones.
To avoid damage from possible batlery
leakage
Remove the batteries if you do not plan to
use the Remote Com'nander for a fairly
long time.
Preface 11
Chapter 1: Setting Up
ConnectingTVAntenna/Cable
Although you can use either an indoor or outdoor antenna with the TV, an outdoor antenna will provice you with better picture
quality. You can receive cable TV by connecting a cable supplied by your local cable company.
75-ohm coaxial cable (round)
Checkyour antennacabletypeandpreparethe end
ofthe cableusingthe F-typeconnector.
Attach an F-type connector (not supplied).
a
mm(1/4 inch) 10mm(3/8 inch) F-typeconnector
3mm(1/8inch)
c
d
rear of the TV.
Plug the connector into the VHF/UHF terminal at the
300-ohm twin-lead cable (flat)
Check your antenna cable lype and prepare the end of
the cable using the 300-ohrn twin-lead cable.
Attach an antenna conne_;tor (not supplied).
a
Loosen both
b
C
rear of the TV.
Plug the connector into the VHF/UHF terminal at the
(Rear of TV)
screws on the
connector with a
screwdriver.
Attach the cable
and tighten both
screws with a
screwdriver.
Most combination antennas are equipped with a signal
splitter.
Remove the splitter and attach the appropriate connector.
VHF/UHF
For better picture quality, conne(:t optional antenna cable so
that the 300-ohm twin-lead cable can be separated a
distance from the TV.
2 1chlpter 1: Setting Up
m
__ !_"2_'_!_kVA_"l::l_IP'_';ILJ]_l_ll_'_i]_=]_._
!
UHF VHF
(Rear of TV)
VHFAJHF
Use an EAC-66 UA/mixer (not supplied).
(RearofTV)
AUX
\, ,,, n/l/
TO CONVERTER CArV
cable
VHF/UHF
VHFAJHF
antennacable
Do not connect anything to the TO CONVERTER terminal in
this case _
(Rearof IV)
AUX
Prepare the VHF antenna cable using the appropriateconnector (p. 12).
Connect the cable to the U/V mixer.
Connect the U/V mixer to the VHF/UHF terminal.
When you use the U/V mixer
Snow and noise may appear in the picture when viewing
cable TV channels over 37 (W+I).
TO
CONVERTER
Converter/
decorder
75-ohmcoaxialcable
VHF/UHF (notsupplied)
CATV cable
Pay cable TV systems use scrambled or encoded signals
require special converters (decoders) in addition to the
normal cable connection.
* The special converterldecoder will be supplied by the cable
company.
Chapter 1: Setting Up 13
UsingtheOn-ScreenMenus
The following flow chart shows the different levels of on-screen menus that you can use to make v,_ri_us adjustments and
settings. See the indicated pages for instructions on using each feature.
For picture quality adjustment
Mainmenu
• V IDEO
AUD IO
TIME
SET UP
CLOSED CAPT ION
Use € _ Exited]
For sound quality adjustment
Mainmenu
VIDEO
•AUDIO
TIME
SET UP
CLOSED CAPTION
Use €_ Exit i_)
For time-related settings
Mainmenu
VIDEO
AUDIO
•TIME
SET UP
CLOSED CAPTION
Use €_ Exit i_
VIDEO menu (pp. 32-33)
VIDEO
PI CTURE IIIIIIIIHIIIIIIIIIHIIII
HUE .............}...............
COLOR I]lllllllfllllllk...........
• BRIGHT Ilglllllflllllll...............
SHARP Ilglllllllllllll..............
_MENU
Use # _ Exit_
AUDIO menu (pp. 34-37)
AUDIO
TREBLE IIIIIIIIllllllll_............
• BASS Ifllllllllll]lll_..............
BALANCE.........I............
SURROUND:OFF
MTS: MAIN
SPEAKER: ON
_MENU
TIME menu
TIME
• CURRENT TIME SET
ON/OFF TIMER
CHANNEL BLOCK
_MENU
: AM
Use # _ Exited]
Adjustment bar
BRIGHTNESS
IIIIIIIIIIIIlllllllllllllllIltllll..............................
Adjustment bar
i
BASS
HIIIIIHIIHHIII..............................
CURRENTTIME SETscreen(pp._l-45)
CURRENT TIME SET
• ___ --:--- _
_MENU
Use € f_ Exiting]
AUDIO OUT screen(p. 37)
AUDIO OUT
•VARIABLE
FIXED
_MENU
Use € R_I_] Exiting1
For language setting (p. 16)
(KV-27TS32 only)
Main menu
VIDEO
AUDIO
TIME
SET UP
CLOSED CAPTION
,ENGLISH
Use €_ Exit_
For language setting (p.16)
(KV-2970M/2975M only)
Main menu
VIDEO
AUDIO
TIME
SET UP
•ENGLISH
Use € _ Exit_
4 Chapter 1: Setting Up
ON/OFFTIMER screen(pp.46-4_
ON/OFF TIMER
• EVERY SUN-SAT
12:00AH._h CH___
_MENU
Use € _ Exitl_
:HANNELBLOCKscreen(pp.48-¢9)
CHANNEL BLOCK
• EVERY SUN-SAT
12:00AH__h CH___
_MENU
Use € _ Exitli_l
For presetting and other functions
Main menu SETUPmenu
V I DEO
AUD IO
T 11_4E
='SE'F UP
CLOSED CAPTION
Use # (_ Exit""""""""""_
For closed caption setting
Mainmenu
V I DEO
AUD IO
T lIME
SET UP
='CLOSED CAPTION
Use € _ Exit_)
SET UP
='CABLE: ON
AUTO PROGRAM
CH ERASE/ADD
CH CAPTION/GUIDE
S VIDEO
VIDEO LABEL
_MENU
CLOSED CAPTION screen
(p. 31)
CLOSED CAPTION
='I'd'I/TEXT OFF
I_-'_11
TEXT1
TEXT2
_MENU
Use €_ Exit_
CABLE ON/OFFscreen(p.l_
ISET UP
I='CABLE: ON
AUTO PROGRAM
CH ERASE/ADD
CH CAPTION/GUIDE
S VIDEO
VIDEO LABEL
_MENU
AUTO PROGRAM screen (p. 18)
==
AUTO PROGRAM
==
¢D
CHANNEL ERASE/ADD screen (pp. 1.9--2:1)
CH ERASE/ADD
10
='ERASE
ADD
_MENU
Select the channel
Use €_ Exitl_
Remote Commander
CODESET CABLEBOX"IV
To display the main menu
Press MENU.
To return to the previous menu
Press A+ or _- to select "_ MENU."
Then press RETURN.
To return to the main menu
Repeat the above, until you reach the main menu.
To return to the normal screen
Press MENU on the Remote Commander.
CHANNEL CAPTION/GUIDE screen (pp. 50-51)
CH CAPTION/GUIDE
@®® ='---
®@@ .....
®®® a
_®1"_
Use € _ Exit_
S VIDEO ON/OFF screen (p. 28)
SET UP
CABLE: ON
AUTO PROGRAM
CH ERASE/ADD
CH CAPTION/GUIDE
='S VIDEO: ON
VIDEO LABEL
3MENU
VIDEOLABELscreen(pp. 53-54)
VIDEO LABEL
='VIDEO1:VIDEO1
VIDEO2:VIDEO2
VIDEO3:VIDEO3
3MENU
Use # _ Exit_
The menus disappear automatically if you do not press a button
withl n 90 seconds.
The menu you cannot select appears in black.
Chapter 1: Setting Up 1 5
UsingtheOn-ScreenMenus
I -vOluI,,z+-_, °P°wl_ o_n_zo ]
f
MUTING_ c_)SLEEP
W/VIDEO T V CABLEPOWER
Q®®
Q®®
®®®
®ES
vl ,
CODESET CABLEBOXTV
The menu language is factory-set to ENGLISH. Follow these instructions to
change the menu language to Spanish or back to En£1ish.
Press POWER on the TV or the Remote Cornm;]nder to turn the TV on.
1
POWER
POWER
©
Press MENU.
2
The main menu appears.
MENU
_V I DEO
AUD I0
TIME
SET UP
CLOSED CAPTION
ENGL ISH
Use € _ Exit_}
SWAP PIP
_ C22) (Z_
CH AUDIO W/VIDEO
(Z2) C3 _
CH • II
REC • TV/VTR
__________----_
RM-Y118
To return to the normal screen
Press MENU
Press A+ or _7- to select ENGLISH.
Then press RETURN.
RETURN
Each time you press z_+ or V.-,
Press A+ or _7-to select language.
ESPAfilOL and ENGLISH menus ,_pear.
(R)
Certain parts of the ESPANOL menus remain in English.
Press RETURN.Thelanguage isselected.
RETURN
V I DEO
AUD IO
TIME
SET UP
CLOSED CAPTION
ENGL I SH
Use # _ Exit1_)
VIDEO
AUDIO
HORA
AJUSTES
CLOSED CAPTION
ESPAROL
Usar#_ Salir_
VIDEO
AUDIO
TIME
SET UP
CLOSED CAPTION
ENGLISH
Use € RI'_-_ Exit_
VIDEO
AUDIO
FLORA
AJUSTES
CLOSED CAPTION
_ESPAROL
Usar¢_-]J._ :Salir_T_l
Spanish menu
6 Chapter 1 : Setting Up
TurningtheCableModeOnorOff
All of the controls are on _#eRemote
Commar_ler.
MUTING(_t (_SLEEP _@___
1NNIDFO T V CABLEPOWER
C, ® @
Q ® @
(_DISPLAY @ c_ENTER
VOL CH
(_':HGUIDE 88_;
CODESET CABLEBOXTV
RESET _ MENU
_-'_0-_ _ RETURN
CH AUDIO WNIDEO
CZ) C_ CZ_
CH • II
CZ) (ZZ) c._.;)
<1-<1 b.- I_-
REC • TV/VrR
If you have cable connected to your TV (pp.12-13), follow the steps below to turn
the cable connection on or off. CABLE is preset to ON when you use your TV for
the first time. Then turn CABLE to OFF to preset or watch VHF: or UHF channels
(pp.18-21 and 29).
Press MENU.The main menu appears.
MENU
,v I I)EO
AUI)IO
T ]ME
SET UP
CLOSED CAPTION
Use € _ Exitl_-'_
Press A+ or V- to select SET UP.
VI})EO
AUI)I O
(R)
T IME
,SEt UP
CLOSED CAPTI ON
Press FIETURN.
Use # _ Exit_}_)
TheSETUPmenuappears,and thecursorpoints
to "CABLE".
RETURN
SET UP
,CABLE: ON
AUTO PROGRAM
[_FIFJ
]f the CABLE display appears in black, the TV is
in VIDEO mode and you cannot select CABLE.
Press TV or TV/VIDEO to change to TV mode.
Press RETURN again.
3
RETURN
CH ERASE/ADD
CH CAPTION/GUIDE
S VIDEO
VIDEO LABEL
DMENU
SET UP
,CABLE: ON
AUTO PROGRAM
CH ERASE/ADD
OH CAPTION/GUIDE
S VIDEO
VIDEO LABEL
D_ENU
Press z3+ or V- to select ON or OFF alternately.
SET UP
CABLE: ON
AUTO PROGRAM
CH ERASE/ADD
CH CAPTION/GUIDE
S VIDEO
VIDEO LABEL
_MENU
s_ uP
CABLE: OFF
AUTO PROGRAM
C_ ERASEIADD
C_ CAPTION/GUIIDE
S VIDEO
VIDEO LABEL
D_iENU
=3
RM-Y118
To return to the normal screen
Press MENU.
Press RETURN.
Thesetting is completed.
Chapter I:SettingUp 17
PresettingW Channels
Press POWER on the TV or the Remote Commander to turn the TV on.
1
F
MUTING(_ _..._SLEEP
T V CABLEPOWER
VOL OH
IODESET CABLEBOXW
RESET _ MENU
POWER
Q
Set the cable connection on or off, depending on if you want to preset cableor VHF/UHF channels.
(Follow the steps in "Turning the Cable Mode On or Off", p.17)
The main menu appears.
Press MENU.
MENU
POWER
,V IDEO
AUDIO
TIME
SET UP
CLOSED CAPTION
Use € _ Exitl_l
__ RETURN
db
CH AUDIO "rVNIDEO
_i F.E_ZE
c_ :cDj c::3
CH • II
C_ CZ) _
REC • TVNTR
C2_ _ C2_
RM-Y118
Channels that can be received on this TV:
I 2-13Ij4-69I 1-125I
Press A+ or _7- to select SET UP.
4
Then press RETURN.
The SET UP menu appears.
(R) RETURN
I_FIFJ
If the AUTO PROGRAM display appears in black, the TV is iq vdeo mode and you cannot select
AUTO PROGRAM. Press TV or TVNIDEO to change to TV mcde.
Press A+ or V- to select AUTO PROGRAM.Then press RETURN.
"AUTO PROGRAM" appears on the screen and receivable ch_ nnels (other than ,thechannels
already preset) are preset in numerical sequence. The channels previously preset will not remain
in the TV's memory.
When no more channels can be found, the programming stops and the lowest nt,,mbered channel
is displayed.
To erase unnecessary channels, or to add channels that could not be preset
automatically because their signal was too weak, follow the steps in "Erasing
Unnecessary Channels -- CHANNEL ERASE" (pp.19-20) and "Presetting Only
Desired Channels -- CHANNEL ADD" (p. 21).
SET UP
,CABLE: ON
AUTO PROGRAM
OH ERASE/ADD
CH CAPTION/GUIDE
S VIDEO
VIDEO LABEL
i _MENU
I
;ET UP
CABLE: ON
•AUTO PROGRAM
OH ERASE/ADD
CH CAPTION/GUIDE
S VIDEO
VIDEO LABEL
_MENU
8 Chapter 1: Setting Up