Sony KDL-52WL135 User Manual

3-295-908-11(1)

Installing the Wall-Mount Bracket

To Customers

For product protection and safety reasons, Sony strongly recommends that wall-mounting of your TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.

Your KDL-52WL135 can be wall-mounted using the SU-WL500 Wall-Mount Bracket (sold separately). Please provide your licensed contractor with this installation supplement as well as the instructions (supplied with the SU-WL500 Wall-Mount Bracket). Read these documents carefully for safety and proper installation.

To Sony Dealers and Contractors

Provide full attention to safety during the installation, periodic maintenance and examination of this product.

Installing the TV on a wall

The TV can be installed on a wall by attaching a WallMount Bracket (sold separately). Verify your TV’s model number and be sure to use the bracket specified for your model only. Refer to the steps on this leaflet along with the instructions supplied with the SU-WL500 Wall-Mount Bracket, to properly carry out the installation.

Sufficient expertise is required in installing this product, especially to determine the strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for any damage or injury caused by mishandling or improper installation.

For product protection and safety reasons, Sony strongly recommends that you use the WallMount Bracket model designed for your TV and that the wall-mounting of your TV is performed by Sony dealers or licensed contractors.

KDL-52WL135

Step 1: Checking the parts

required for the installation

Open the Wall-Mount Bracket package and check the contents for all required parts along with the Instructions.

Step 2: Deciding on the

installation location

Decide where you want to install your TV. Refer to the reverse page for the TV installation dimensions table.

Refer to the Instructions for SU-WL500.

Step 3: Installing the Base

Bracket on the wall

Refer to the Instructions for SU-WL500.

Printed in Mexico

Step 4: Preparing for the

installation of the TV

Follow the steps below to prepare for installing the TV.

Disconnect all the cables from the

TV.

Start removing the screws behind

the TV.

Do not remove any other screws from the TV.

Secure the Mounting Hook to the

rear of the TV.

Referring to the Screw and Hook locations diagram/table on the reverse page, determine the screw positions, and secure the Mounting Hook to the rear of the TV.

1 Secure the Mounting Hook to the rear of the

TV temporarily, using the supplied four screws (+PSW6 × 16).

2 Be sure that both screws are securely

tightened with equal torque strength to the rear of the TV.

Align the tab on the rear of the Mounting Hook with the square hole on the rear of the TV as in the illustration below.

Square hole

Note

Be sure not to use any screws other than the supplied ones (+PSW6 × 16) when securing the Mounting Hook.

Adjust the angle of the Mounting

Tab

Hook using the hexagon wrench supplied with the Wall-Mount Bracket.

When installing the TV parallel to the wall (0 degrees), adjustment of the Mounting Hook angle (procedures 1 and 2 below) is not necessary. Make sure that each arm base X is screwed in securely.

1 Remove the two screws from the arm base

X of the Mounting Hook. Choose the holes corresponding to the desired angle (5, 10, 15 or 20 degrees).

2 Adjust the angles of the top Y and bottom

Z arm to fit the corresponding hole, and

firmly secure each arm using the two screws removed in the previous procedure 1.

Notes

• Be sure to adjust the right and left arms to the same angle.

• Make sure that the two arm bases are screwed in securely.

CAUTION

Be careful not to pinch your fingers when adjusting the angle of the Mounting Hook.

Lift the TV off the stand. Make

sure that you carry out this task with at least two or three people.

Do not attempt to lift the TV by yourself.

Step 5: Installing the TV on the

wall

Refer to the instructions for SU-WL500.

Notes

• When you put the TV back on the stand, reverse the above steps (insert the posts of the stand, aligning with the lines on the rear of the TV).

• When moving the TV, do not squeeze the bottom of the front panel too strongly.

• Remove the screws or install the Mounting Hook on a stable and level surface.

Square hole

Mounting Hook

Screw (+PSW6 × 16)

Hexagon wrench

TV installation dimensions table

Screw and Hook locations diagram/table

Model Name Screw location Hook location

KDL-52WL135 d, g a

)

320 (12

Screen center point

Unit: mm (inches)

Length for each mounting angle

Angle (0˚) Angle (20˚)

Model Name

Display Screen center

dimensions dimensions

AB C DEFGH

KDL-52WL135

1278 832 73 519 183 410 797 555

(50

/8) (32 7/8) (2 7/8) (20 1/2) (7 1/4) (16 1/4) (31 1/2) (21 7/8)

Figures in the above table may differ slightly depending on the installation.

WARNING

The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV. Refer to your TV’s instructions for its weight.

Screw location

When installing the Mounting Hook on the TV.

Hook location

When installing the TV onto the Base Bracket.

a b*

* Hook positions “b” and “c” cannot be used for the model in the table

above.