Sony KDL-40W3000, KDL-46W3000, KDL-52W3000 User Manual

3-212-598-11(1)

LCD Digital Color TV

KDL-40W3000 KDL-46W3000 KDL-52W3000

Operating Instructions

Owner’s Record

The model and serial numbers are located at the rear of the TV. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this TV.

Model Name

Serial No.

WARNING

To reduce the risk of fire or electric shock, do not expose this TV to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE DE CHOC ELECTRIQUE,

NE PAS OUVRIR

PRECAUCION

RIESGO DE CHOQUE ELECTRICO

NO ABRIR

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the TV’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the TV.

The TV shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV.

CAUTION

To prevent electric shock, do not use this polarized AC plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

Declaration of Conformity

Trade Name: SONY Model: KDL-40W3000/KDL-46W3000/ KDL-52W3000 Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone Number: 858-942-2230

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

s Reorient or relocate the receiving antenna. s Increase the separation between the

equipment and receiver.

s Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected.

s Consult the dealer or an experienced radio/

TV technician for help.

Pursuant to FCC regulations, you are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Safety

s Operate the TV only on 120 - 240 V AC. s Use the AC power cord specified by Sony

and suitable for the voltage where you use it.

s The plug is designed, for safety purposes,

to fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

s If any liquid or solid object should fall

inside the cabinet, unplug the TV immediately and have it checked by qualified service personnel before operating it further.

s If you will not be using the TV for several

days, disconnect the power by pulling the plug itself. Never pull on the cord.

s For details concerning safety precautions,

see “Important Safety Instructions” on page 4.

Installing

s The TV should be installed near an easily

accessible power outlet.

s To prevent internal heat buildup, do not

block the ventilation openings.

s Do not install the TV in a hot or humid

place, or in a place subject to excessive dust or mechanical vibration.

s Avoid operating the TV at temperatures

below 41°F (5°C).

s If the TV is transported directl y from a cold

to a warm location, or if the room temperature changes suddenly, the picture may be blurred or show poor color due to moisture condensation. In this case, please wait a few hours to let the moisture evaporate before turning on the TV.

s To obtain the best picture, do not expose

the screen to direct illumination or direct sunlight. It is recommended to use spot lighting directed down from the ceiling or to cover the windows that face the screen with opaque drapery. It is desirable to install the TV in a room where the floor and walls are not of a reflective material.

CAUTION

Use the following Sony TVs only with the following WALL-MOUNT BRACKET or TV-stand.

Sony TV Model No.

KDL-40W3000 KDL-46W3000 KDL-52W3000

Sony Wall-Mount Bracket Mode No.

Sony TV-Stand Model No.

Use with other WALL-MOUNT BRACKET or TV-stand may cause instability and possibly result in injury.

SU-FL300M

To Customers

Sufficient expertise is required for installing the specified TV. Be sure to subcontract the installation to Sony dealers or licensed contractors and pay adequate attention to safety during the installation.

Note

This television includes a QAM demodulator which should allow you to receive unscrambled digital cable television programming via subscription service to a cable service provider. Availability of digital cable television programming in your area depends on the type of programming and signal provided by your cable service provider.

Trademark Information

Macintosh is a trademark of Apple Inc., registered in the U.S. and other countries.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Manufactured under license from Dolby Laboratories. “Dolby” and double-D symbol are trademarks of Dolby Laboratories.

Blu-ray Disc is a trademark.

“BRAVIA” and , S-Force, BRAVIA Theatre Sync, , DMe Color” are trademarks or registered marks of Sony Corporation.

“XMB” and “xross media bar” are the trademarks of Sony Corporation and Sony Computer Entertainment Inc.

“PLAYSTATION” is a registered trademark and “PS3” is a trademark of Sony Computer Entertainment Inc.

Adobe is a registered trademark or a trademark of Adobe Systems Incorporated in United States and/or other countries.

SU-WL500

RHT-G800

SU-FL300M

SU-FL300L

and “x.v.

NOTIFICATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Contents

Important Safety Instructions ............................4

Welcome to the World of BRAVIA™

The Four Steps to Full HD Experience: Set,

Sound, Source, and Setup............................8

Picture Quality and Aspect Ratio.......................8

TV Home Menu: XMB

(Xross Media Bar)........9

™

Getting Started

1. Installing the TV.............................................10

Preventing the TV from Toppling Over.........10

Preparation for Wall-Mounting......................10

2. Locating Inputs and Outputs .......................11

Left Side .......................................................11

Rear..............................................................12

3. Connecting the TV.........................................14

Cable System or VHF/UHF Antenna

System ......................................................14

Cable System and VHF/UHF Antenna

System ......................................................14

HD Cable Box/HD Satellite Box....................14

PC.................................................................16

Other Equipment ..........................................17

Using HDMI Control for BRAVIA Theatre

Sync™.......................................................18

Bundling the Connecting Cables ..................18

4. Setting Up the Channel List

– Initial Setup ...............................................19

Using the TV Features

Remote Control and TV Controls/

Indicators .....................................................20

Inserting Batteries into the Remote

Control.......................................................20

Remote Control and TV Controls .................20

Indicators......................................................25

Programming the Remote Control...................26

Operating Sony Brand Video Equipment......26

Programming Non-Sony Video

Equipment.................................................26

Using Other Equipment with Your Remote

Control..........................................................28

Using P&P and PIP Features............................31

To Display the Sub Window .........................31

To Change Inputs or Channels in the

Window .....................................................31

To Change the Window Size of P&P............31

To Exit from P&P and PIP............................31

Using the Menus

Adjusting TV Settings.................................32

Watching TV.................................................32

Accessing the Equipment Connected to

Your TV.........................................................32

Navigating through TV Home Menu on

............................................................33

XMB

™

TV Setting Description......................................34

Product Support......................................34

Clock/Timers Settings.............................34

Picture Settings ......................................34

Sound Settings .......................................36

Screen Settings ......................................37

Video Options Settings ...........................38

Audio Options Settings ...........................39

Channel Settings ....................................40

Closed Captions (CC) Settings...............41

Parental Lock Settings............................41

External Inputs Settings..........................44

HDMI Settings ........................................44

General Settings.....................................45

Initial Setup.............................................45

Other Information

Troubleshooting................................................46

Specifications....................................................49

Index...................................................................51

Quick Setup Guide (separate volume)

Provides a variety of optional equipment connection diagrams.

Customer Support

http://www.sony.com/tvsupport

On-line Registration

United States http://productregistration.sony.com Canada http://www.SonyStyle.ca/registration

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

USE

AC power cord

Observe the followings to prevent the AC power cord from being damaged. If the AC power cord is damaged, it may result in a fire or an electric shock. Stop using it and ask your dealer or Sony service center to exchange it.

s Do not place the TV where the power cord is subject to wear or abuse. s Do not pinch, bend, or twist the cord excessively. The core lines may

be bared and cut, causing a short-circuit, and resulting in a fire or an electric shock.

s Do not convert or damage the power cord. s Do not allow anything to rest on or roll over the

power cord.

s Do not move the TV with the power cord

plugged in.

s Keep the power cord away from heat sources. s When you disconnect the AC power cord,

disconnect it from the wall outlet first.

s Be sure to grasp the plug when disconnecting the power cord. Do not

pull the power cord.

s Do not use the supplied AC power cord on any other equipment. s Use only an original Sony AC power cord, not other brands.

Wall outlet

The TV set with a three-wire grounding type AC power cord plug must be connected to an AC power socket outlet with a protective earthing connection.

Do not use a poor fitting outlet. Insert the plug fully into the outlet. If it is loose, it may cause arcing and result in a fire. Contact your electrician to have the outlet changed.

Wiring

When connecting cables, be sure to unplug the AC power cord for your safety. Take care not to catch your feet on the cables. It may damage the TV set.

Electric shock

Do not touch the AC power cord or the TV with a wet hand. If you plug/unplug the AC power cord from the TV with a wet hand, it may cause electric shock.

Lightning storms

For added protection for this TV during a lightning storm, or when it is lef t unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to th e TV due to lightning and power line surges.

When not in use

If you will not be using the TV set for several days, the TV set should be disconnected from the AC power outlet for environmental and safety reasons. The TV set is not disconnected from the AC power source when the TV set is switched off. To disconnect the TV set completely, pull the plug from the AC power outlet.

Overloading

This TV set is designed to operate on a 120 - 240 V AC supply on ly. Take care not to connect too many appliances to the same AC power outlet as this could result in a fire or an electric shock.

Optional equipment

Do not install optional equipment too close to the TV set. Picture distortion and/or noisy sound may occur if the TV set is positioned in close proximity to any equipment emitting electromagnetic radiation.

Small accessories

Keep small accessories out of children’s reach.

ANTENNAS

Outdoor antenna grounding

If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits.

WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.

Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Section 810 of the National Electrical Code (NEC) in the U.S.A. and Section 54 of the Canadian Electrical Code in Canada provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Antenna grounding according to the National Electrical Code, ANSI/NFPA 70

Antenna lead-in wire

Ground clamps

Antenna discharge unit

Electric service equipment

NEC: National Electrical Code

(NEC Section 810-20)

Grounding conductors (NEC Section 810-21)

Ground clamps

Power service grounding electrode system (NEC Art 250 Part H)

MAGNETIC INFLUENCE

This TV contains a strong magnet in the speaker unit that generates a magnetic field. Keep any items susceptible to magnetic fields away from the speaker.

SOUND

If a snapping or popping sound from the TV is continuous or frequent while the TV is operating, unplug the TV and consult your dealer or service technician. It is normal for some TV’s to make occasional snapping or popping sounds, particularly when being turned on or off.

CARRYING THE TV

Carry the TV in the specified manner

To avoid dropping the TV and causing serious injury, be sure to follow these guidelines:

s Before carrying the TV, disconnect all cables. s Carrying the large size TV requires two or more people. s When you carry the TV, place your hand as illustrated and hold it

securely. Do not put stress on the LCD panel.

s When carrying the TV, do not subject it to shocks or vibration, or

excessive force.

s When lifting or moving the TV, hold it firmly from the bottom. Place

your palm directly underneath but do not squeeze the panel’s speaker grill area.

BATTERIES

s Do not dispose of batteries in a fire. s Do not short circuit, disassemble or overheat the batteries. s Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type.

Disposal of used batteries

To preserve our environment, dispose of used batteries according to your local laws or regulations.

CLEANING

Cleaning the AC power plug

Unplug the AC power plug and clean it regularly. If the plug is covered with dust and it picks up moisture, its insulation may deteriorate and result in a fire.

Cleaning the screen surface/ cabinet of the TV set

Unplug the AC power cord when cleaning this TV. If not, it may result in electric shock. Clean the cabinet of the TV with a dry soft cloth. To remove dust from the screen, wipe it gently with a soft cloth. Stubborn stains may be removed with a cloth slightly dampened with a solution of mild soap and warm water. Never use strong solvents such as thinner or benzine for cleaning. If using a chemically pretreated cloth, please follow the instruction provided on the package. The ventilation holes can accumulate dust over time. To ensure proper ventilation, we recommend removing the dust periodically (once a month) using a vacuum cleaner.

(Continued)

VENTILATION

The slots and openings in the TV are provided for necessary ventilation. To ensure reliable operation of the TV and to protect it from overheating, these slots and openings must never be blocked or covered.

Unless proper ventilation is provided, the TV may gather dust and get dirty. For proper ventilation, observe the following:

s Do not install the TV face up, down or sideways. s Do not install the TV turned over or upside

down.

s Never cover the slots and openings with a cloth

or other materials.

s Never block the slots and openings by

placing the TV on a bed, sofa, rug or other similar surface.

s Never place the TV in a confined space, such as

a bookcase or built-in cabinet, unless proper ventilation is provided.

eave some space around the TV set as shown below. Otherwise, air-circulation may be inadequate and cause overheating, which may cause a fire or damage to the TV set.

Installed on the wall

4 inches (10 cm)

Installed with stand

4 inches (10 cm)

Never install the TV set as follows:

Air circulation is blocked. Air circulation is blocked.

inches

(30 cm)

4 inches (10 cm)

Leave at least this space

4 inches (10 cm)

inches

(30 cm)

around the set.

4 inches (10 cm)

Leave at least this space around the set.

inches

(6 cm)

Objects and ventilation holes

Never push objects of any kind into t he TV through the cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or an electric shock. Do not place any objects on the TV.

MOISTURE

Moisture and flammable objects

s The TV must not be exposed to dripping or splashing. Do not place

objects filled with liquids, such as vases, on the TV.

s Do not use power-line operated TV sets near

water — for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. It may result in a fire or an electric shock.

s Do not let this TV get wet. Never spill liquid

of any kind on the TV. If any liquid or solid object does fall through, do not operate the TV. It may result in electric shock or damage to the TV. Have it checked immediately by qualified personnel.

s To prevent fire, keep flammable objects or open

flame (e.g. candles) away from the TV.

INSTALLATION

Wall mount installation requires the use of a Wall-Mount Bracket. When installing or removing the TV, using the Wall-Mount Bracket, be sure to use qualified contractors. If not properly secured during installation or removal from the Wall-Mount Bracket, the TV may fall and cause serious injury.

Optional wall mount

Observe the following when installing the TV using a Wall-Mount Bracket.

s Be sure to follow the operating instructions supplied with the

Wall-Mount Bracket when installing the TV.

s Be sure to attach the brackets supplied with the Wall-Mount Bracket. s Do not hang the TV from the ceiling. It may fall and cause serious

injury.

Placement

The TV should be installed near an easily accessible AC power outlet.

Observe the following in placing the TV. Otherwise the TV may fall from the stand or wall mount, causing damage or serious injury.

s Place the TV on a stable, level surface. s Do not hang anything on the TV. Do not allow

children to climb on the TV.

Do not install the TV in places subject to extreme temperature, such as in direct sunlight, near a radiator, or heating vent. If the TV is exposed to

Wall Wall

extreme temperature, the TV may overheat and cause deformation of the enclosure or cause the TV to malfunction. Do not install the TV in a place exposed to direct air conditioning. If the TV is installed in such a location, moisture may condense inside and may cause a malfunction.

s Never place the TV in hot, oily, humid or

excessively dusty places.

s Do not install the TV where insects may

enter.

s Do not install the TV where it may be

exposed to mechanical vibration.

s Do not install the TV in a location where it may protrude, such as on

or behind a pillar, or where you might bump your head on it. Otherwise, it may result in injury.

Preventing the TV from toppling over

Take measures to prevent the TV from toppling over and causing injury. To prevent the TV from toppling over, secure the TV to a wall or stand.

Placement for viewing

It is recommended to watch the TV at a distance of 3 - 7 times that of the screen height, and in moderate brightness. Watching the TV for too long or in a dark room may cause eye fatigue. To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use spot lighting directed down from the ceiling.

Outdoor use

Do not install this TV outdoors. If the TV is exposed to rain, it may result in a fire or an electric shock. Do not expose the TV to direct sunlight, it may heat up and become damaged.

Vehicle, ships and other vessels

Do not install this TV in a vehicle.

Bumping of the vehicle may cause the TV to fall down and cause injury.

Do not install this TV in a ship or vessel. If the TV is exposed to seawater, it may cause a fire or damage the TV.

Medical institutions

Do not place this TV in a place where medical equipment is in use.

It may cause a malfunction of medical equipment.

VOLUME ADJUSTMENT

s Adjust the volume so as not to trouble your neighbors. Sound carries

very easily at night. Therefore, closing the windows or using headphones is suggested.

s When using headphones, adjust the volume so as to avoid excessive

levels, as hearing damage may result.

LCD SCREEN

s Although the LCD screen is made with high-precision technology

and has effective pixels of 99.99% or more, black dots or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD panel and is not a malfunction.

s The LCD screen is made with high-precision technology and to

achieve a high level of performance and picture quality, this TV’s backlight setting is set to maximize the brightness of the TV. However, uneven brightness may be observed when the LCD TV is viewed in a dark ambient without an input source or a blank screen. This condition is normal and not a malfunction of the TV. Changing the Picture mode, Backlight setting, enabling the Light Sensor, or turning on the Power management will improve this condition.

s Do not expose the LCD screen surface to direct sunlight. Doing so

may damage the LCD panel.

s Do not push or scratch the LCD screen, or place objects on top of the

TV. The image may be uneven or the LCD panel may be damaged.

s If the TV is used in a cold place, a smear may occur in the picture or

the picture may become dark. This does not indicate a failure. These phenomena improve as the temperature rises.

s Ghosting may occur when still pictures are displayed continuously. It

should disappear after a few moments.

s The screen and cabinet get warm when the TV is in use. This is not a

malfunction.

s Avoid spraying insect repellent with volatile material on the screen. s Avoid prolonged contact with rubber or plastic material.

Broken pieces

Do not throw anything at the TV. The screen glass may break by the impact and cause serious injury.

If the surface of the TV cracks, do not touch it until you have unplugged the AC power cord.

Otherwise electric shock may result.

Handling of broken glass and liquid crystal leakage

If the LCD panel gets damaged, crystalline liquid leakage may occur, or scattered broken glass may result. Do not touch broken glass or crystalline liquid which is toxic, with bare hands as cuts, poisoning or skin irritation may occur. Also, do not let glass fragments or leaked crystalline liquid get into your eyes or mouth. Should either contact your eyes or mouth, rinse the contacted area thor oughly with water and consult your doctor.

SERVICING

Do not attempt to service the TV yourself since opening the cabinet may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Replacement parts

When replacement parts are required, be sure the service technician certifies in writing that he/she has used replacement parts specified by the manufacturer that have the same characteristics as the original parts.

Unauthorized substitutions may result in a fire, an electric shock or other hazards.

Safety check

Upon completion of any service or repairs to the TV, ask the service technician to perform routine safety checks (as specified by the manufacturer) to determine that the TV is in safe operating condition, and to so certify. Ask a qualified service technician to dispose of the TV.

For Customers in the United States

Lamp in this product contains mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (http://www.eiae.org).

Welcome to the World of BRAVIA™

Thank you for purchasing this Sony BRAVIA™ high-definition television. The quality of the image you see on your BRAVIA TV is only as good as the quality of the signal it receives. To experience the full detail of your new BRAVIA TV, you need access to HD programming. Your BRAVIA TV can receive and display HD programming from:

• Over-the-air broadcasting via HD-quality antenna

• HD cable subscription

• HD satellite subscription

• Blu-ray Disc™ Player or other external equipment

Contact your cable or satellite provider for information on upgrading to HD programming.

To learn more about HDTV, visit: http://www.sony.com/HDTV

The Four Steps to Full HD Experience: Set, Sound, Source, and Setup

Along with your BRAVIA TV set, a complete HD system requires an HD sound system, a source of HD programming and proper setup connections. This manual explains basic setup

connections (see page 14). The Quick Setup Guide, enclosed separately, illustrates how to connect other optional equipment.

Picture Quality and Aspect Ratio

You can enjoy crisp, clear images, smooth movement and high-impact visuals from 1080 HD signals. When you compare a high-definition signal to a standard analog signal, you will notice a big difference. The 1080 HD signals provide more than twice the vertical resolution of the standard TV signal.

High-definition and standard-definition signals are transmitted with different aspect ratios (the width-to-height ratio of the image). HDTV uses a wider screen than conventional standarddefinition TV.

16:9 (high-definition) source

Most HDTV signals use a wide screen aspect rati of 16:9. The 16:9 fills your BRAVIA screen and maintains a crisp, clear, vivid picture.

4:3 (standard-definition) source

Most standard-definition signals use a boxy 4:3 aspect ratio. When a 4:3 image is displayed on an HDTV, you will see black bars on the sides. The picture quality may not be as sharp as with HD sources.

• You can use the Wide Mode function of the TV to adjust the 4:3 image to fit the entire screen (see pages 23, 37

and 38).

TV Home Menu: XMB™ (Xross Media Bar)

The XMB™ is a menu of BRAVIA features and input sources displayed on the TV screen. The XMB HOME button on your remote control to access the XMB

is an easy way to select programming and adjust settings on your BRAVIA TV. Press the

™

Product Support

Clock/Timers

™

Settings

Media Category Bar

Sound

Screen

Video Options

Category Object Bar

From the horizontal Media Category Bar you can control:

• Settings: timer, picture, sound, screen and other options (see page 34 for customization options).

• TV Channels: available channels are displayed on the vertical Category Object Bar.

• External Inputs: cable, satellite, VCR, DVD players or other inputs can also be selected from the Category Object Bar for the External Inputs.

• This manual is for the 40, 46 and 52 inch BRAVIA KDL-W Series models with screen size measured diagonally.

Getting Started

1. Installing the TV

Preventing the TV from Toppling Over

TV stand

Table-Top Stand

1 Screw the support belt (supplied) to the TV

stand with a wood screw (supplied).

2 Attach the support belt to the Table-Top Stand

with the securing screw (supplied) using a coin, etc.

3 Adjust the length by pulling the support belt

toward you while holding the Table-Top Stand.

• Be sure to take measures to prevent the TV from toppling over and causing injury.

• The supplied wood screw may not be used depending on the type of TV stand. In this case, or when the securing strength is not enough, use commercial

screws TV stand. Consult your dealer about the types of screw(s).

/8 to 3/16 inch (3 to 4 mm) diameter to fit to the

Preparation for Wall-Mounting

This TV can be installed on a wall by using a WallMount Bracket (sold separately). Before mounting the TV on a wall, the Table-Top Stand must be removed from the TV.

Follow the simple steps below to remove the Table-Top Stand:

1 Disconnect all the cables from the TV. 2 Start removing the screws behind the TV (See

illustration below). Do not remove any other screws from the TV.

3 Secure the Mounting Hook to the rear of the

TV.

4 Adjust the angle of the Mounting Hook. 5 When screws are removed, lift the TV off the

stand. Make sure that you carry out this task with at least two people. Do not attempt to lift the TV by yourself.

• Do not remove the Table-Top Stand for any reason other than to wall-mount the TV.

• When using an electric screwdriver, set the torque setting to approximately 2 N·m {20 Kgf·cm}.

• Be sure to store the removed screws and Table-Top Stand in a safe place until you are ready to reattach the Table-Top Stand. Keep the screws away from small children.

• For bracket installation, refer to the supplied Installing the Wall-Mount Bracket and the instruction guide provided by the Wall-Mount Bracket model for your TV. Sufficient expertise is required in installing this TV, especially to determine the strength of the wall for withstanding the TV’s weight.

• For product protection and safety reasons, Sony strongly recommends that you use the Wall-Mount Bracket model designed for your TV and that the wall-mounting of your TV is performed by a Sony dealer or licensed contractor.

2. Locating Inputs and Outputs

Left Side

VIDEO IN

VIDEO

(MONO)

AUDI O

Getting Started

Item Description

1 Headphone jack Connects to your headphones. If your headphones do not match the jack, use a suitable

plug adapter (not supplied).

• While headphones are connected, the TV speakers are muted.

2 VIDEO IN 2

VIDEO/R-AUDIOL (MONO)

Connects to the composite video and audio output jacks on your camcorder or other video equipment such as a VCR or video game equipment.

• If you have mono equipment, connect its audio output jack to the TV’s L (MONO) audio input jack.

3 HDMI IN 2

HDMI

HDMI (High-Definition Multimedia Interface) provides an uncompressed, all-digital audio/video interface between this TV and any HDMI-equipped audio/video equipment, such as a set-top box, DVD player, Blu-ray Disc Player, A/V receiver as well as PC. HDMI supports enhanced, or high-definition video, plus digital audio.

• HDMI connection is necessary to view 480i, 480p, 720p, 1080i, 1080p and 1080/24p formats. Note that this TV displays all video input signals in a resolution of 1,920 dots × 1,080 lines.

• Be sure to use only an HDMI cable that bears the HDMI logo.

• When HDMI control compatible equipment is connected, communication with the connected equipment is supported. Refer to page 44 to set up this communication.

• When connecting a HDMI control compatible audio system with HDMI jack, be sure to also connect to the OPTICAL OUT jack.

Rear

AUDIO

DMeX/SERVICE

AUDIO OUT

(VAR/FIX)

PC IN

AUDI O

1132

S VIDEO

VIDEO

(MONO)

AUDI O

VIDEO IN

AUDI O

COMPONENT IN

(1080p/1080i/

720p/480p/480i)

DIGITAL

OUT

(OPTICAL)

AUDI O

Item Description

1 PC IN

(RGB/AUDIO)

Connects to a personal computer’s video output connector using a HD15-HD15 cable with ferrite core (analog RGB, not supplied). Can also be connected to other analog RGB equipment. See “PC Input Signal Reference Chart” on page 16 for the signals that can be displayed.

• For some Apple Macintosh computers, it may be necessary to use an adapter (not supplied). If this is the case, connect the adapter to the computer before connecting the HD15-HD15 cable with ferrite core.

• If the picture is noisy, flickering or not clear, adjust Phase and Pitch of Screen settings on page 38.

VHF/UHF/CABLE

Item Description

2 HDMI IN 1

HDMI/ R-AUDIO-L

3 HDMI IN 3

HDMI

If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the HDMI IN 1 (with DVI-to-HDMI cable or adapter) jack, and connect the audio jack to the AUDIO IN (L/R) jacks of HDMI IN 1.

DVI-to-HDMI cable

DVI-to-HDMI adapter

• HDMI connection is necessary to view 480i, 480p, 720p, 1080i, 1080p and 1080/24p formats. Note that this TV displays all video input signals in a resolution of 1,920 dots × 1,080 lines.

• Be sure to use only an HDMI cable that bears the HDMI logo.

• When HDMI control compatible equipment is connected, communication with the connected equipment is supported. Refer to page 44 to set up this communication.

• When connecting a HDMI control compatible audio system with HDMI jack, be sure to also connect to the OPTICAL OUT jack.

4 VIDEO IN 1

S VIDEO

VIDEO IN 1/3

VIDEO/L(MONO)AUDIO-R

6 COMPONENT IN

1/2 (1080p/1080i/ 720p/480p/480i)/ L-AUDIO-R

7 DMe

8 DIGITAL OUT

9 AUDIO OUT

0 AC IN Connects the supplied AC power cord. qa VHF/UHF/CABLE RF input that connects to your Cable or VHF/UHF antenna.

/ SERVICE This USB port is for service only unless you are connecting the optional BRAVIA

(OPTICAL)

(VAR/FIX)

Connects to the S VIDEO output jack of your VCR or other video equipment that has S VIDEO. S VIDEO provides better picture quality than composite video (5) connection. If both composite video and S VIDEO are connected, S VIDEO signal has priority.

Connects to the composite video and audio output jacks on your A/V equipment such as a VCR or other video equipment. A third composite video and audio (VIDEO IN 2) is located on the left side of the TV.

Connects to your equipment’s component video (YP Component video provides better picture quality than the S VIDEO (4) or the composite video (5) connection.

BPR) and audio (L/R) jacks.

• Component video (YPBPR) connection is necessary to view 480i, 480p, 720p, 1080i and 1080p formats. Note that this TV displays all video input signals in a resolution of 1,920 dots × 1,080 lines.

external module (DMe

Connects to the optical audio input of your digital audio equipment that is PCM/Dolby Digital compatible. Dolby Digital Audio signal from the HDMI input will be output as PCM.

Connects to the left and right audio input jacks of your analog audio equipment. You can use these outputs to listen to your TV’s audio through your stereo system.

Getting Started

Audio cable

3. Connecting the TV

HD Cable Box/HD Satellite Box

Cable System or VHF/UHF Antenna System

You can enjoy high-definition and standarddefinition digital programming (if available in your area) along with standard-definition analog programming.

• This TV is capable of receiving unscrambled digital programming for both cable (QAM and 8VSB) and external VHF/UHF antenna (ATSC).

• It is strongly recommended that you connect the antenna/cable input using the 75-ohm coaxial cable (not supplied) to receive optimum picture quality. A 300-ohm twin lead cable can be easily affected by radio frequency interference, resulting in signal degradation.

Cable or VHF/UHF (or VHF only)

75-ohm coaxial cable

VHF/UHF/CABLE input

Cable System and VHF/UHF Antenna System

Use an optional A-B RF switch (not supplied) to switch between the cable and over-the-air antenna programming, as indicated below.

Rear of TV

You can also enjoy high-definition programming by subscribing to a high-definition cable service or a high-definition satellite service. For the best possible picture, make sure you connect this equipment to your TV via the HDMI or component video (with audio) input on the back of your TV.

Shown with HDMI Connection

Rear of TV

AUDIO

CATV/Satellite antenna cable

PC IN

RGB

AUDIO

HDMI cable

HD cable box/ HD satellite box

A-B RF switch

Cable

Antenna

VHF/UHF/CABLE input

Rear of TV

• Be sure to set the Cable setting to On or Off in the Channel settings for the type of input signal you

choose (see page 40).

Shown with DVI Connection

CATV/Satellite antenna cable

Rear of TV

AUDIO

DVI-to-HDMI cable

HD cable box/ HD satellite box

AUDIO

AUDIO-L (white) AUDIO-R (red)

Audio cable

• If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the HDMI IN 1 (with DVI-to-HDMI cable or adapter) jack and connect the audio jack to the AUDIO IN (L/R) jacks of HDMI IN 1. For details, see page 13.

Getting Started

Shown with Component Connection

Rear of TV

1132

S VIDEO

VIDEO

(MONO)

AUDI O

VIDEO IN

AUDIO-R (red)

AUDIO-L (white)

B (blue)

Y (green)

R (red)

AUDI O

COMPONENT IN

(1080p/1080I/

(1080p/1080i/

720p/480p/480i)

720p/480p/480I)

DMex/SERVICE

AUDIO OUT

(VAR/FIX)

HD cable box/HD satellite box

DIGITAL

OUT

(OPTICAL)

AUDI O

Component video cable

CATV/Satellite antenna cable

Audio cable

Use the TV as a monitor for your PC. Shown below with the HD15 to HD15 connection. This TV can also be connected to a PC with DVI or HDMI output. (Refer to the separate Quick Setup Guide.)

Rear of TV

HD15-HD15 cable (analog RGB)

Audio cable (stereo mini plugs)

AUDIO

Connect to an HDMI compatible PC with an HDMI cable.

• Connect the PC IN jack to the PC using the HD15HD15 cable with ferrite core (analog RGB, not supplied) and audio cable (page 12).

PC Input Signal Reference Chart

After connecting the PC to the TV, set the output signal from the PC according to the chart below.

Resolution Signals Horizontal

(Pixel)

VGA 640

640

720

SVGA

XGA

WXGA

SXGA

HDTV

800

1024

1280

1360

1280

1920

× Ver tical

(Line)

480 31.5 60 VGA

480 37.5 75 VESA

400 31.5 70 VGA-T

600 37.9 60 VESA Guidelines

600 46.9 75 VESA

768 48.4 60 VESA Guidelines

768 56.5 70 VESA

768 60.0 75 VESA

768 47.4 60 VESA

768 47.8 60 VESA

768 60.3 75

768 47.7 60 VESA

1024 64.0 60 VESA

1024 80.0 75 VESA

1080 67.5 60

• If the PC is connected to the TV and no signal has been input from the PC for more than 30 seconds, the TV enters the standby mode automatically (page 45).

Horizontal frequency (kHz)

Vertical frequency (Hz)

Standard

• This TV’s PC input does not support Sync on Green or Composite Sync.

• This TV’s PC VGA input does not support interlaced signals.

• For the best picture quality, it is recommended to use the signals (boldfaced) in the above chart with a 60 Hz vertical frequency from a personal computer. In plug and play, signals with a 60 Hz vertical frequency will be detected automatically. (PC reboot may be necessary.)

Other Equipment

Personal computer

Disc Player/ PS3

Rear of TV

Blu-ray

AUDI O

(1080p/1080I/

(1080p/1080i/

720p/480p/480I)

720p/480p/480i)

PC IN

AUDI O

1132

S VIDEO

VIDEO

(MONO)

AUDI O

VIDEO IN

RGB

AUDI O

AUDIO

COMPONENT IN

DMex/SERVICE

DIGITAL

OUT

(OPTICAL)

AUDI O

AUDIO OUT

(VAR/FIX)

DVD player

Audio system

Digital satellite receiver

Personal computer

VHF/UHF/CABLE

Digital cable box

Headphones

VIDEO IN

VIDEO

(MONO)

AUDIO

Getting Started

VCR

Game system

Digital recorder

Analog audio equipment (A/V Receiver/Home Theater)

Digital audio equipment

• Refer to the Quick Setup Guide (supplied) when connecting other equipment to your TV.

Camcorder/ PS3

Camcorder

+ 39 hidden pages