Sony KDL-40T28xx, KDL-32D27, KDL-32D26xx, KDL-32D27xx, KDL-32T30 User Manual

...
3-198-502-13(1)
U
LCD Digital Colour TV
KDL-40S30xx KDL-40D26xx KDL-40T30xx KDL-32D27xx KDL-32T28xx
Operating Instructions
KDL-40D27xx KDL-40T28xx KDL-32S30xx KDL-32D26xx KDL-32T30xx
© 2007 Sony Corporation
For useful information about Sony products
NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM
Introduction
Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference.
A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 10 AMP fuse approved by ASTA or BSI to BS 1362 (i.e., marked with or ) must be used. When an alternative type of plug is used it should be fitted with a 10 AMP FUSE (KDL-32D27xx, KDL-32T28xx, KDL-32S30xx, KDL-32D26xx, KDL-32T30xx), 13 AMP FUSE (KDL-40D27xx, KDL-40T28xx, KDL-40S30xx, KDL-40D26xx, KDL-40T30xx) otherwise the circuit should be protected by a 10 AMP FUSE (KDL-32D27xx, KDL­32T28xx, KDL-32S30xx, KDL-32D26xx, KDL-32T30xx), 13 AMP FUSE (KDL-40D27xx, KDL-40T28xx, KDL­40S30xx, KDL-40D26xx, KDL-40T30xx) at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
FUSE
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and replace the fuse.
Disposal of the TV set
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
Notice for Digital TV function
• Any functions related to Digital TV ( ) will only work in countries or areas where DVB-T (MPEG2) digital terrestrial signals are broadcast or where you have access to a compatible DVB-C (MPEG2) cable service. Please confirm with your local dealer if you can receive a DVB­T signal where you live or ask your cable provider if their DVB-C cable service is suitable for integrated operation with this TV.
• The cable provider may charge an additional fee for such a service and you may be required to agree to their terms and conditions of business.
• Although this TV set follows DVB-T and DVB-C specifications, compatibility with future DVB-T digital terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.
• Some Digital TV functions may not be available in some countries/regions and DVB-C cable may not operate correctly with all providers.
• For more information about DVB-C functionality please see our cable support site: http://support.sony-europe.com/tv/DVBC
Trademark information
is a registered trademark of the DVB Project
• Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under one or more of the following US patents: 5510752, 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.
• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
DIGITAL
~
• The illustrations used in this manual are of the KDL-32D2710 unless otherwise state.
The "xx" that appears on the model name, corresponds to two numeric digits related to colour variation.
.
GB
2
Table of Contents
Start-up Guide 4
Start-up Guide 4
Safety information.....................................................................................................................7
Precautions...............................................................................................................................8
Overview of the remote ..........................................................................................................9
Overview of the TV buttons and indicators........................................................................10
Watching TV
Watching TV............................................................................................................................11
Checking the Digital Electronic Programme Guide (EPG) ............................................13
Using the Digital Favourite list ......................................................................................15
Using Optional Equipment
Connecting optional equipment...............................................................................................16
Viewing pictures from connected equipment ..........................................................................17
Using HDMI control.................................................................................................................18
Using MENU Functions
Navigating through menus......................................................................................................19
Picture Adjustment menu........................................................................................................20
Sound Adjustment menu.........................................................................................................22
Features menu........................................................................................................................24
Set-up menu............................................................................................................................26
Digital Set-up menu .....................................................................................................29
Additional Information
Specifications..........................................................................................................................31
Troubleshooting ......................................................................................................................33
GB
: for digital channels only
3
GB
Start-up Guide
C
1: Checking the accessories
Mains lead (1) (only for KDL-40S30xx, KDL-40D27xx, KDL-40D26xx, KDL-40T28xx, KDL40T30xx)
Coaxial cable* (1) (only for KDL-40S30xx, KDL­40D27xx, KDL-40D26xx, KDL-40T28xx, KDL40T30xx)
Remote RM-ED009 (1)
Size AA batteries (R6 type) (2)
Support belt (1) and screws (2)
2: Connecting an aerial/ VCR
onnecting an aerial/cable
Terrestrial signal
or cable
Coaxial cable*
To insert batteries into the remote
Push and lift the cover to open.
Connecting an aerial/cable and VCR
~
• Observe the correct polarity when inserting batteries.
• Do not use different types of batteries together or mix old and new batteries.
• Dispose of batteries in an environmentally friendly way. Certain regions may regulate disposal of batteries. Please consult your local authority.
• Handle the remote with care. Do not drop or step on it, or spill liquid of any kind onto it.
• Do not place the remote in a location near a heat source, a place subject to direct sunlight, or a damp room.
Coaxial cable*
Terrestrial signal
Scart lead (not supplied)
Coaxial cable (not supplied)
VCR
GB
4
or cable
3: Preventing the TV
6:
Selecting the language
Start-up Guide
from toppling over
~
For models with swivel stand (KDL-32T30xx, KDL­40T30xx) do not tense the support belt.
4: Connecting the cables
and country/region
3,4
KDL-40S30xx KDL-40D27xx KDL-40D26xx KDL-40T28xx KDL-40T30xx
5: Bundling the cables
1 Connect the TV to your mains socket
(220-240V AC, 50Hz).
2 Press 1 on the TV (top side).
When you switch on the TV for the first time, the Language menu appears on the screen.
3 Press F/f to select the language displayed on the
menu screens, then press .
Auto Start Up
Language
Country
Select:
Confirm:
Continued
5
GB
4 Press F/f to select the country/region in
which you will operate the TV, then press
.
Auto Start Up
Language
Country
Back:
Select:
If the country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region.
Confirm:
7: Auto-tuning the TV
1 Before you start auto-tuning the TV, insert
a pre-recorded tape into the VCR connected to the TV (page 4) and start play back.
The video channel will be located and stored on the TV during auto-tuning. If no VCR is connected to the TV, skip this step.
2 Press .
Do you want to start automatic tuning?
Back:
Start:
Cancel:
MENU
5 Press MENU to exit.
The TV has now tuned in all the available channels.
~
When a digital broadcast channel cannot be received, or when selecting a region in which there are no digital broadcasts in step 4 (page 6), the time must be set after performing step 5.
To tune the TV for Cable connection
1 press . 2 Press F/f to select “Quick Scan” or “Full
Scan”, then press .
"Quick Scan" : channels are tuned according to the cable operator information within the broadcast signal. Recommended setting for "Frequency", "Network ID" and "Symbol Rate" is "Auto". This option is recommended for fast tuning when supported by your cable operator. If the "Quick Scan" does not tune, please use the "Full Scan" method below. "Full Scan" : All available channels are tuned and stored. This procedure may take some time. This option is recommended when "Quick Scan" is not supported by your cable provider. For further information about supported cable providers, refer to support web site: http://support.sony-europe.com/TV/DVBC
3 Press G/g/f to select “Start”.
The TV starts searching for channels. Do not press any buttons on the TV or remote.
~
Some cable providers do not support “Quick Scan”. If no channels are detected using “Quick Scan”, perform “Full Scan”.
3 Press F/f to select “Antenna” or “Cable”,
then press .
If you select “Cable”, the screen for selecting the scan type appears. See “To tune the TV for Cable connection” (page 6). The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, so do not press any buttons on the TV or remote while proceeding.
If a message appears for you to confirm the aerial connection
No digital or analogue channels were found. Check all the aerial/cable connection and then press to start auto-tuning again.
4 When the Programme Sorting menu
appears on the screen, follow the steps of “Programme Sorting” (page 26).
If you do not change the order in which the analogue channels are stored on the TV, go to step 5.
GB
6
Detaching the Table­Top Stand from the TV
~
Do not remove the Table-Top Stand for any reason other than to wall-mount the TV.
KDL-40S30xx KDL-40D27xx KDL-40D26xx KDL-40T28xx KDL-40T30xx
KDL-32S30xx KDL-32D27xx KDL-32D26xx KDL-32T28xx KDL-32T30xx
Installed with stand
Safety information
Installation/Set-up
Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries.
Installation
• The TV set should be installed near an easily accessible mains socket.
• Place the TV set on a stable, level surface.
• Only qualified service personnel should carry out wall installations.
• For safety reasons, it is strongly recommended that you use Sony accessories, including: – Wall-mount bracket SU-WL500
Transporting
• Before transporting the TV set, disconnect all cables.
• Two or three people are needed to transport a large TV set.
• When transporting the TV set by hand, hold it as shown on the right.
• When lifting or moving the TV set, hold it firmly from the bottom. Do not put stress on the LCD panel.
• When transporting the TV set, do not subject it to jolts or excessive vibration.
• When transporting the TV set for repairs or when moving, pack it using the original carton and packing material.
30 cm
10 cm10 cm
6 cm
Leave at least this space around the set.
• To ensure proper ventilation and prevent the collection of dirt or dust: – Do not lay the TV set flat, install upside down,
backwards, or sideways.
– Do not place the TV set on a shelf, rug, bed or in a
closet.
– Do not cover the TV set with a cloth, such as curtains,
or items such as newspapers, etc.
– Do not install the TV set as shown below.
Air circulation is blocked.
Wall
Air circulation is blocked.
Wall
Ventilation
• Never cover the ventilation holes or insert anything in the cabinet.
• Leave space around the TV set as shown below.
• It is strongly recommended that you use a Sony wall­mount bracket in order to provide adequate air-circulation.
Installed on the wall
30 cm
10 cm
10 cm
10 cm
Leave at least this space around the set.
Mains lead
Handle the mains lead and socket as follows in order to avoid any risk of fire, electrical shock or damage and/or injuries:
Connect the TV set using a three-wire grounding type mains plug to a mains socket with a protective earthing connection (only for KDL-40S30xx, KDL-40D27xx, KDL-40D26xx, KDL-40T28xx, KDL-40T30xx). – Use only Sony mains leads, not those of other brands. – Insert the plug fully into the mains socket. – Operate the TV set on a 220-240 V AC supply only. – When wiring cables, be sure to unplug the mains lead
for your safety and care not to catch your feet on the cables.
– Disconnect the mains lead from the mains socket before
working on or moving the TV set. – Keep the mains lead away from heat sources. – Unplug the mains plug and clean it regularly. If the plug
is covered with dust and it picks up moisture, its
insulation may deteriorate, which could result in a fire.
Continued
7
GB
Notes
• Do not use the supplied mains lead on any other equipment.
• Do not pinch, bend, or twist the mains lead excessively. The core conductors may be exposed or broken.
• Do not modify the mains lead.
• Do not put anything heavy on the mains lead.
• Do not pull on the mains lead itself when disconnecting the mains lead.
• Do not connect too many appliances to the same mains socket.
• Do not use a poor fitting mains socket.
When:
– Mains lead is damaged. – Poor fitting of mains socket. – TV set is damaged by being dropped, hit or having
something thrown at it.
– Any liquid or solid object falls through openings in the
cabinet.
Precautions
Prohibited Usage
Do not install/use the TV set in locations, environments or situations such as those listed below, or the TV set may malfunction and cause a fire, electrical shock, damage and/or injuries.
Location:
Outdoors (in direct sunlight), at the seashore, on a ship or other vessel, inside a vehicle, in medical institutions, near flammable objects (candles, etc).
Environment:
Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration; unstable locations; near water, rain, moisture or smoke.
Situation:
Do not use when your hands are wet, with the cabinet removed, or with attachments not recommended by the manufacturer. Disconnect the TV set from mains socket and aerial during lightning storms.
Broken pieces:
• Do not throw anything at the TV set. The screen glass may break by the impact and cause serious injury.
• If the surface of the TV set cracks, do not touch it until you have unplugged the mains lead. Otherwise electric shock may result.
When not in use
• If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons.
• As the TV set is not disconnected from the mains when the TV set is just turned off, pull the plug from the mains to disconnect the TV set completely.
• However, some TV sets may have features that require the TV set to be left in standby to work correctly.
For children
• Do not allow children to climb on the TV set.
• Keep small accessories out of the reach of children, so that they are not mistakenly swallowed.
If the following problems occur...
Turn off the TV set and unplug the mains lead immediately if any of the following problems occur. Ask your dealer or Sony service centre to have it checked by qualified service personnel.
Viewing the TV
• View the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.
• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.
LCD Screen
• Although the LCD screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction.
• Do not push or scratch the front filter, or place objects on top of this TV set. The image may be uneven or the LCD screen may be damaged.
• If this TV set is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises.
• Ghosting may occur when still pictures are displayed continuously. It may disappear after a few moments.
• The screen and cabinet get warm when this TV set is in use. This is not a malfunction.
• The LCD screen contains a small amount of liquid crystal and mercury. The fluorescent tubes used in this TV set also contains mercury. Follow your local ordinances and regulations for disposal.
Handling and cleaning the screen surface/cabinet of the TV set
Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning. To avoid material degradation or screen coating degradation, observe the following precautions.
• To remove dust from the screen surface/cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.
• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material.
• When adjusting the angle of the TV set, move it slowly so as to prevent the TV set from moving or slipping off from its table stand
Optional Equipment
Keep optional components or any equipment emitting electromagnetic radiation away from the TV set. Otherwise picture distortion and/or noisy sound may occur.
GB
8
Overview of the remote
1 "/1 – TV standby
Turns the TV on and off from standby mode.
2 A/B – Dual Sound (page 22) 3 Coloured buttons (page 12, 13, 15) 4 / – Input select / Text hold
• In TV mode: Selects the input source from equipment connected to the TV sockets (page 17).
• In Text mode (page 12): Holds the current page.
5 F/f/G/g/ 6 TOOLS (page 12, 18)
Enables you to access various viewing options and change/make adjustments according to the source and screen format.
7 MENU (page 19) 8 THEATRE
You can set Theatre Mode on or off. When Theatre Mode is set to on, the optimum audio output (if the TV is connected with an audio system using an HDMI cable) and picture quality for film videos are automatically set.
9 Number buttons
• In TV mode: Selects channels. For channel numbers 10 and above, enter the second and third digit quickly.
• In Text mode: Enters the three digit page number to select the page.
0 – Previous channel
Returns to the previous channel watched (for more than five seconds).
qa PROG +/-/ /
• In TV mode: Selects the next (+) or previous (-) channel.
• In Text mode (page 12): Selects the next ( ) or previous ( ) page.
qs % – Mute the sound qd 2 +/- – Volume qf / – Text (page 12) qg DIGITAL – Digital mode (page 11) qh ANALOG – Analogue mode (page 11) qj RETURN /
Returns to the previous screen of any displayed menu.
qk – EPG (Digital Electronic Programme Guide) (page 13) ql – Picture freeze (page 12)
Freezes the TV picture.
w; – Screen mode (page 12) wa / – Info / Text reveal
• In digital mode: Displays brief details of the programme currently being watched.
• In analogue mode: Displays information such as current channel number and screen format.
• In Text mode (page 12): Reveals hidden information (e.g. answers to a quiz).
z
• The number 5, PROG + and A/B buttons have tactile dots. Use the tactile dots as references when operating the TV.
• If you turn the TV off, Theatre Mode is also turned off.
GB
9
Overview of the TV buttons and indicators
1 (page 19) 2 / – Input select / OK
• In TV mode: Selects the input source from equipment connected to the TV sockets (page 17).
• In TV menu: Selects the menu or option, and confirms the setting.
3 2 +/-/ /
• In TV mode: Increases (+) or decreases (-) the volume.
• In TV menu: Moves through the options right ( ) or left ( ).
4 PROG +/-/ /
• In TV mode: Selects the next (+) or previous (-) channel.
• In TV menu: Moves through the options up ( ) or down ( ).
5 1 – Power
Turns the TV on or off.
~
To disconnect the TV completely, pull the plug from the mains.
6 – Picture Off / Timer indicator
• Lights up in green when the picture is switched off (page 24).
• Lights up in orange when the timer is set (page 25).
7 1 – Standby indicator
Lights up in red when the TV is in standby mode.
8 " – Power / Timer REC programme
indicator
• Lights up in green when the TV is turned on.
• Lights up in orange when the timer recording is set (page 13).
• Lights up in red during the timer recording.
9 Remote control sensor
• Receives IR signals from the remote.
• Do not put anything over the sensor, as its function may be affected.
~
Make sure that the TV is completely turned off before unplugging the mains lead. Unplugging the mains lead while the TV is turned on may cause the indicator to remain lit or may cause the TV to malfunction.
10
GB
Watching TV
Watching TV
2
3 Press the number buttons or PROG +/- to
select a TV channel.
To select channel numbers 10 and above using the number buttons, enter the second and third digits within two seconds. To select a digital channel using the Digital Electronic Programme Guide (EPG), see page 13.
In digital mode
An information banner appears briefly. The following icons may be indicated on the banner.
: Interactive service is av ailable (MHEG Digital
Text)
: Interactive service (MHEG Digital Text) is
currently disabled : Radio service : Scrambled/Subscription service
: Multiple audio languages available
2
3
: Subtitles available : Subtitles available for the hearing impaired : Recommended minimum age for current
programme (from 4 to 18 years)
: Parental Lock
c: Current programme is being recorded
Additional operations
To Do this
3
Turn on the TV from Standby mode without sound
Adjust the volume Press 2 + (increase)/
Access the Programme index table (in analogue mode only)
Press %. Press 2 +/- to set the volume level.
- (decrease). Press . To select an analogue
channel, press
.
F/f, then press
Watching TV
1 Press 1 on the TV (top side) to switch on
the TV.
When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV.
2 Press DIGITAL to switch to digital mode or
ANALOG to switch to analogue mode.
The channels available vary depending on the mode.
Continued
11
GB
Loading...
+ 24 hidden pages