Page 1
A-DAE-100-12(1)
Additional Information for
Using Sony Wall-Mount Bracket (SU-WL100)
Compatible TV models for this Wall-Mount Bracket information:
KDL-26L5000
KDL-22L5000
For product protection and safety reasons, Sony strongly recommends that you use the
Wall-Mount Bracket model designed for your TV and that the wall-mounting of your TV
is performed by Sony dealers or licensed contractors.
To Customers
Please provide your licensed contractor with this installation supplement as well as the instructions
(supplied with the SU-WL100 Wall-Mount Bracket). Read these documents carefully for safety and proper
installation.
To Sony Dealers and Contractors
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Sufficient expertise is required in installing this product, especially to determine the strength
of the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product
to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during
the installation. Sony is not liable for any damage or injury caused by mishandling or improper
installation.
For proper installation, follow your wall-mount bracket instructions and the directions below.
Additional Information for Using Sony Wall-Mount Bracket (SU-WL100)
− 1 −
Page 2
Step 1: Checking the parts required for the installation
Open the Wall-Mount Bracket package and check the contents for all required parts along with the
Instructions.
Step 2: Adjusting the position of the holders of the Base Plate
Follow the same procedure as for a 20 inch TV.
Refer to the Instructions for SU-WL100.
Step 3: Deciding on the installation location
Decide where you want to install your TV. Refer to the TV installation dimensions table.
Refer to the Instructions for SU-WL100.
Dimension Table
Screen center point
Unit: inches (mm)
Model Name
KDL-26L5000
KDL-22L5000
Figures in the above table may dier slightly depending on the installation.
Display
dimensions
26 3/4
(679)
22
(558)
17 1/4
(435)
14 5/8
(370)
Screen center
dimensions
3 7/8
(98)
5 1/4
(133)
Length for each mounting angle
Angle (0°) Angle (20°)
12 5/8
(318)
13
(330)
6 1/8
(154)
5 5/8
(140)
10 1/4
(258)
8 5/8
(219)
16 3/8
(411)
13 7/8
(350)
12 3/4
(323)
13
(329)
CAUTION
e wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV.
Refer to your TV’s operating instructions for its weight.
Step 4: Installing the Base Plate on the wall
Refer to the Instructions for SU-WL100.
Additional Information for Using Sony Wall-Mount Bracket (SU-WL100)
− 2 −
Page 3
Step 5: Preparing the TV for wall mount installation
a
b
Follow the steps below to prepare for installing the TV.
1 Disconnect all the cables from the TV.
2 Align the holes on the left Mounting Hook with the corresponding holes on the
rear of the TV.
Secure them to the TV using two screws (supplied with SU-WL100).
When using an electric screwdriver to tighten the screws, the torque must be approximately
1.5 N·m (15 kgf·cm). Do not li the Mounting Hook before the screws (two screws each for
le/right) are secured.
Screw
(+PSW 4 × 12)
Mounting Hook
Hook locations diagram
KDL-26L5000: Install the TV onto the location “a” of the Base Plate.
KDL-22L5000: Install the TV onto the location “b” of the Base Plate.
Additional Information for Using Sony Wall-Mount Bracket (SU-WL100)
− 3 −
Page 4
3 Adjust the angle of the Mounting Hook.
Mounting Hook
Arm
4 Align the holes on the right Mounting Hook with the corresponding holes on
the rear of the TV.
Secure them to the TV using two screws (supplied with SU-WL100).
Screw
(+PSW 4 × 12)
Mounting Hook
Step 6: Installing the TV on the Base Plate
Refer to the Instructions for SU-WL100.
1 Connect the AC power cord and cables to the corresponding inputs on the rear
of the TV.
For details on the cable connection, refer to the Operating Instructions for your TV.
2 Install the TV onto the Base Plate.
Additional Information for Using Sony Wall-Mount Bracket (SU-WL100)
− 4 −
Loading...