Sony KDL-20S3060 User Manual [ru]

3-271-059-41(0)

LCD Digital Colour TV

KDL-20S30xx

Operating Instructions

Before operating the TV, please read the “Safety information” section of this manual. Retain this manual for future reference.

Инструкция по эксплуатации

Перед включением телевизора прочтите раздел “Сведения по безопасности” этого руководства. Сохраняйте данное руководство для справок в будущем.

For useful information about Sony products

Для получения полезной информации о продукции Сони

Introduction

Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference.

Disposal of the TV set

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Notice for Digital TV function

• Any functions related to Digital TV ( ) will only

work in countries or areas where DVB-T (MPEG2) digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive a DVB-T signal where you live.

• Although this TV set follows DVB-T specifications,

compatibility with future DVB-T digital terrestrial broadcasts cannot be guaranteed.

• Some Digital TV functions may not be available in some

countries.

Trademark information

• is a registered trademark of the DVB Project

• Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under one or more of the following US patents: 5510752, 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.

• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

DIGITAL

The "xx" that appears on the model name, corresponds to two numeric digits related to colour variation.

Table of Contents

Start-up Guide 4

Safety information .....................................................................................................................7

Precautions ...............................................................................................................................8

Overview of the remote ..........................................................................................................9

Overview of the TV buttons and indicators ........................................................................10

Watching TV

Watching TV............................................................................................................................11

Checking the Digital Electronic Programme Guide (EPG) .............................................13

Using the Digital Favourite list .......................................................................................15

Using Optional Equipment

Connecting optional equipment...............................................................................................16

Viewing pictures from connected equipment ..........................................................................17

Using HDMI control .................................................................................................................18

Using MENU Functions

Navigating through menus ......................................................................................................19

Picture Adjustment menu ........................................................................................................20

Sound Adjustment menu.........................................................................................................22

Features menu ........................................................................................................................24

Set-up menu............................................................................................................................26

Digital Set-up menu .......................................................................................................29

Additional Information

Specifications ..........................................................................................................................31

Troubleshooting ......................................................................................................................33

: for digital channels only

Start-up Guide

1: Checking the accessories

Remote RM-ED009 (1) Size AA batteries (R6 type) (2)

Support belt (1) and screws (2)

To insert batteries into the remote

Push and lift the cover to open.

• Observe the correct polarity when inserting batteries.

• Do not use different types of batteries together or mix old and new batteries.

• Dispose of batteries in an environmentally friendly way. Certain regions may regulate disposal of batteries. Please consult your local authority.

• Handle the remote with care. Do not drop or step on it, or spill liquid of any kind onto it.

• Do not place the remote in a location near a heat source, a place subject to direct sunlight, or a damp room.

2: Connecting an aerial/ VCR/ DVD recorder

Connecting an aerial only

Coaxial cable

Connecting an aerial/ VCR/ DVD recorder

Coaxial cable

Scart lead

Coaxial cable

VCR

3: Preventing the TV

Selecting the language,

Start-up Guide

from toppling over

4: Bundling the cables

country/region and location

3,4

1 Connect the TV to your mains socket

(220-240V AC, 50Hz).

2 Press 1 on the TV (top side).

When you switch on the TV for the first time, the Language menu appears on the screen.

3 Press F/f to select the language

displayed on the menu screens, then

press

Auto Start Up

Language

Country

Location

Select:

Confirm:

Continued

4 Press F/f to select the country/region in

which you will operate the TV, then press

Auto Start Up

Language

Country

Location

Back:

Select:

Confirm:

If the country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region.

5 Press F/f to select the location type in

which you will operate the TV, then press .

uto Start Up

Language

Country

Location

Home

Shop

press any buttons on the TV or remote while proceeding.

If a message appears for you to confirm the aerial connection

No digital or analogue channels were found. Check all the aerial connections and press to start auto-tuning again.

3 When the Programme Sorting menu

appears on the screen, follow the steps of “Programme Sorting” (page 26).

If you do not change the order in which the analogue channels are stored on the TV, go to step 4.

4 Press MENU to exit.

The TV has now tuned in all the available channels.

When a digital broadcast channel cannot be received, or when selecting a region in which there are no digital broadcasts in step 4 (page 6), the time must be set after performing step 4.

Detaching the TableTop Stand from the TV

Back:

Select:

Confirm:

This option selects the initial picture mode appropiate for the typical lighting condition in these enviroments.

6: Auto-tuning the TV

1 Before you start auto-tuning the TV, insert

a pre-recorded tape into the VCR connected to the TV (page 4) and start play back.

The video channel will be located and stored on the TV during auto-tuning. If no VCR is connected to the TV, skip this step.

2 Press .

Do you want to start automatic tuning?

Back:

Start:

The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, so do not

Cancel:

Do not remove the Table-Top Stand for any reason other than to wall-mount the TV.

Installed with stand

Safety information

Installation/Set-up

Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries.

Installation

• The TV set should be installed near an easily accessible mains socket.

• Place the TV set on a stable, level surface.

• Only qualified service personnel should carry out wall installations.

• For safety reasons, it is strongly recommended that you use Sony accessories, including:

Wall-mount bracket SU-WL100.

Transporting

• Before transporting the TV set, disconnect all cables.

• When transporting the TV set by hand, hold it as shown on the right. Do not put stress on the LCD panel and the frame around the screen.

• When transporting the TV set, do not subject it to jolts or excessive vibration.

• When transporting the TV set for repairs or when moving, pack it using the original carton and packing material.

30 cm

10 cm10 cm

6 cm

Leave at least this space around the set.

• To ensure proper ventilation and prevent the collection of dirt or dust: – Do not lay the TV set flat, install upside down,

backwards, or sideways.

– Do not place the TV set on a shelf, rug, bed or in a

closet.

– Do not cover the TV set with a cloth, such as curtains,

or items such as newspapers, etc.

– Do not install the TV set as shown below.

Air circulation is blocked.

Wall

Air circulation is blocked.

Wall

Ventilation

• Never cover the ventilation holes or insert anything in the cabinet.

• Leave space around the TV set as shown below.

• It is strongly recommended that you use a Sony wallmount bracket in order to provide adequate air-circulation.

Installed on the wall

30 cm

10 cm

Leave at least this space around the set.

Mains lead

Handle the mains lead and socket as follows in order to avoid any risk of fire, electrical shock or damage and/or injuries:

– Use only Sony mains leads, not those of other brands. – Insert the plug fully into the mains socket. – Operate the TV set on a 220-240 V AC supply only. – When wiring cables, be sure to unplug the mains lead

for your safety and take care not to catch your feet on the cables.

– Disconnect the mains lead from the mains socket before

working on or moving the TV set. – Keep the mains lead away from heat sources. – Unplug the mains plug and clean it regularly. If the plug

is covered with dust and it picks up moisture, its

insulation may deteriorate, which could result in a fire.

Notes

• Do not use the supplied mains lead on any other equipment.

• Do not pinch, bend, or twist the mains lead excessively. The core conductors may be exposed or broken.

• Do not modify the mains lead.

• Do not put anything heavy on the mains lead.

• Do not pull on the mains lead itself when disconnecting the mains lead.

Continued

• Do not connect too many appliances to the same mains socket.

• Do not use a poor fitting mains socket.

Precautions

Prohibited Usage

Do not install/use the TV set in locations, environments or situations such as those listed below, or the TV set may malfunction and cause a fire, electrical shock, damage and/or injuries.

Location:

Outdoors (in direct sunlight), at the seashore, on a ship or other vessel, inside a vehicle, in medical institutions, unstable locations, near water, rain, moisture or smoke.

Environment:

Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration, near flammable objects (candles, etc). The TV set shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV.

Situation:

Do not use when your hands are wet, with the cabinet removed, or with attachments not recommended by the manufacturer. Disconnect the TV set from mains socket and aerial during lightning storms.

Broken pieces:

• Do not throw anything at the TV set. The screen glass may break by the impact and cause serious injury.

• If the surface of the TV set cracks, do not touch it until you have unplugged the mains lead. Otherwise electric shock may result.

When not in use

• If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons.

• As the TV set is not disconnected from the mains when the TV set is just turned off, pull the plug from the mains to disconnect the TV set completely.

• However, some TV sets may have features that require the TV set to be left in standby to work correctly.

For children

• Do not allow children to climb on the TV set.

• Keep small accessories out of the reach of children, so that they are not mistakenly swallowed.

Viewing the TV

• View the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.

• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

LCD Screen

• Although the LCD screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction.

• Do not push or scratch the front filter, or place objects on top of this TV set. The image may be uneven or the LCD screen may be damaged.

• If this TV set is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises.

• Ghosting may occur when still pictures are displayed continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this TV set is in use. This is not a malfunction.

• The LCD screen contains a small amount of liquid crystal and mercury. The fluorescent tubes used in this TV set also contain mercury. Follow your local ordinances and regulations for disposal.

Handling and cleaning the screen surface/cabinet of the TV set

Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning. To avoid material degradation or screen coating degradation, observe the following precautions.

• To remove dust from the screen surface/cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.

• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material.

• When adjusting the angle of the TV set, move it slowly so as to prevent the TV set from moving or slipping off from its table stand

If the following problems occur...

Turn off the TV set and unplug the mains lead immediately if any of the following problems occur. Ask your dealer or Sony service centre to have it checked by qualified service personnel.

When:

– Mains lead is damaged. – Poor fitting of mains socket. – TV set is damaged by being dropped, hit or having

something thrown at it.

– Any liquid or solid object falls through openings in the

cabinet.

Optional Equipment

Keep optional components or any equipment emitting electromagnetic radiation away from the TV set. Otherwise picture distortion and/or noisy sound may occur.

Overview of the remote

1 "/1 – TV standby

Turns the TV on and off from standby mode.

2 A/B – Dual Sound (page 22) 3 Coloured buttons (page 12, 13, 15) 4 / – Input select / Text hold

• In TV mode: Selects the input source from equipment connected to the TV sockets (page 17).

• In Text mode (page 12): Holds the current page.

5 F/f/G/g/ 6 TOOLS (page 12, 18)

Enables you to access various viewing options and change/make adjustments according to the source and screen format.

7 MENU (page 19) 8 THEATRE

You can set Theatre Mode on or off. When Theatre Mode is set to on, the optimum audio output (if the TV is connected with an audio system using an HDMI cable) and picture quality for film videos are automatically set.

9 Number buttons

• In TV mode: Selects channels. For channel numbers 10 and above, enter the second and third digit quickly.

• In Text mode: Enters the three digit page number to select the page.

0 – Previous channel

Returns to the previous channel watched (for more than five seconds).

qa PROG +/-/ /

• In TV mode: Selects the next (+) or previous (-) channel.

• In Text mode (page 12): Selects the next ( ) or previous ( ) page.

qs % – Mute the sound qd 2 +/- – Volume qf / – Text (page 12) qg DIGITAL – Digital mode (page 11) qh ANALOG – Analogue mode (page 11) qj RETURN /

Returns to the previous screen of any displayed menu.

qk – EPG (Digital Electronic Programme Guide) (page 13) ql – Picture freeze (page 12)

Freezes the TV picture.

w; – Screen mode (page 12) wa / – Info / Text reveal

• In digital mode: Displays brief details of the programme currently being watched.

• In analogue mode: Displays information such as current channel number and screen format.

• In Text mode (page 12): Reveals hidden information (e.g. answers to a quiz).

• The number 5, PROG + and A/B buttons have tactile dots. Use the tactile dots as references when operating the TV.

• If you turn the TV off, Theatre Mode is also turned off.

Overview of the TV buttons and indicators

1 (page 19) 2 / – Input select / OK

• In TV mode: Selects the input source from equipment connected to the TV sockets (page 17).

• In TV menu: Selects the menu or option, and confirms the setting.

3 2 +/-/ /

• In TV mode: Increases (+) or decreases (-) the volume.

• In TV menu: Moves through the options right ( ) or left ( ).

4 PROG +/-/ /

• In TV mode: Selects the next (+) or previous (-) channel.

• In TV menu: Moves through the options up ( ) or down ( ).

5 1 – Power

Turns the TV on or off.

To disconnect the TV completely, pull the plug from the mains.

6 – Picture Off / Timer indicator

• Lights up in green when the picture is switched off (page 24).

• Lights up in orange when the timer is set (page 25).

7 1 – Standby indicator

Lights up in red when the TV is in standby mode.

8 " – Power / Timer REC programme

indicator

• Lights up in green when the TV is turned on.

• Lights up in orange when the timer recording is set (page 13).

• Lights up in red during the timer recording.

9 Remote control sensor

• Receives IR signals from the remote.

• Do not put anything over the sensor, as its function may be affected.

Make sure that the TV is completely turned off before unplugging the mains lead. Unplugging the mains lead while the TV is turned on may cause the indicator to remain lit or may cause the TV to malfunction.

Watching TV

3 Press the number buttons or PROG +/- to

select a TV channel.

To select channel numbers 10 and above using the number buttons, enter the second and third digits within two seconds. To select a digital channel using the Digital Electronic Programme Guide (EPG), see page 13.

In digital mode

An information banner appears briefly. The following icons may be indicated on the banner.

: Radio service

: Scrambled/Subscription service

: Multiple audio languages available

: Subtitles available

: Subtitles available for the hearing impaired

: Recommended minimum age for current

programme (from 4 to 18 years)

: Parental Lock

c: Current programme is being recorded

Additional operations

To Do this

Turn on the TV from Standby mode without sound

Adjust the volume Press 2 + (increase)/

Access the Programme index table (in analogue mode only)

Press %. Press 2 +/- to set the volume level.

- (decrease).

Press . To select an analogue channel, press

F/f, then press

Watching TV

1 Press 1 on the TV (top side) to switch on

the TV.

When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV.

2 Press DIGITAL to switch to digital mode or

ANALOG to switch to analogue mode.

The channels available vary depending on the mode.

To access Text

Press /. Each time you press /, the display changes cyclically as follows: Text t Text over the TV picture (mix mode) t No Text (exit the Text service) To select a page, press the number buttons or PROG +/-. To hold a page, press / . To reveal hidden information, press / .

When four coloured items appear at the bottom of the Text page, Fastext is available. Fastext allows you to access pages quickly and easily. Press the corresponding coloured button to access the page.

Picture Freeze

Freezes the TV picture (e.g. to make a note of a telephone number or recipe).

1 Press on the remote control. 2 Press F/f/G/g to adjust the position of the

window.

3 Press to remove the window. 4 Press again to return to normal TV

mode.

Not available for AV3, AV4 and PC input.

To change the screen format manually to suit the broadcast

Press repeatedly to select the desired screen format.

Smart*

Displays conventional 4:3 broadcasts with an imitation wide screen effect. The 4:3 picture is stretched to fill the screen.

4:3

Displays conventional 4:3 broadcasts (e.g. non-wide screen TV) in the correct proportions.

Wide

Displays wide screen (16:9) broadcasts in the correct proportions.

Zoom*

Displays cinemascopic (letter box format) broadcasts in the correct proportions.

14:9*

Displays 14:9 broadcasts in the correct proportions. As a result, black border areas are visible on the screen.

* Parts of the top and bottom of the picture may be cut off.

• HD signal source pictures can only be displayed in “Wide” mode .

• You cannot use this function while the digital banner is displayed.

• Some characters and/or letters at the top and the bottom of the picture may not be visible in Smart mode. In such a case, you can select “V-Size” using the “Screen” menu and adjust vertical size to make it visible.

• When “Auto Format” is set to “On”, the TV will automatically select the best mode to suit the broadcast (page 24).

• You can adjust the position of the picture when selecting “Smart” (50Hz), “14:9” or “Zoom”. Press up or down (e.g. to read subtitles).

F/f to move

Using the Tools menu

Press TOOLS to display the following options when viewing a TV programme.

Options Description

Close Closes the Tools menu.

Picture Mode See page 20.

Sound Effect See page 22.

Speaker See page 23.

Audio Language (in digital mode only)

Subtitle Setting (in digital mode only)

Sleep Timer See page 25.

Power Saving See page 24.

System Information (in digital mode only)

See page 30.

Displays the system information screen.

Checking the Digital Electronic Programme Guide (EPG) *

All Categories

1 In digital mode, press . 2 Perform the desired operation as shown in

the following table or displayed on the screen.

Programme information will only be displayed if the TV

Select:

Digital Electronic Programme Guide (EPG)

* This function may not be available in some countries/regions.

To Do this

Watch a programme Press F/f/G/g to select the programme, then press .

Turn off the EPG Press .

Sort the programme information by category – Category list

Set a programme to be recorded – Timer REC

Set a programme to be displayed automatically on the screen when it starts – Reminder

+/- 1 day on/off:

Options:

1 Press the blue button. 2 Press

1 Press F/f/G/g to select the future programme you want to

2 Press 3 Press to set the TV and your VCR timers.

To record the programme you are currently watching, press / .

1 Press F/f/G/g to select the future programme you want to

2 Press

If you switch the TV to standby mode, it will automatically turn itself on when the programme is about to start.

F/f/G/g to select a category, then press .

The categories available include:

“All Categories”: Contains all available channels. Category name (e.g. “News”): Contains all channels corresponding to the

selected category.

record, then press

F/f to select “Timer REC”.

A red c symbol appears by that programme’s information. The indicator on the TV front panel lights up in orange.

display, then press

F/f to select “Reminder”, then press .

A c symbol appears by that programme’s information. The indicator on the TV front panel lights up in orange.

station is transmitting it.

/ .

Watching TV

Continued

To Do this

Set the time and date of a programme you want to record – Manual timer REC

Cancel a recording/reminder – Timer list

• You can set VCR timer recording on the TV only for SmartLink compatible VCRs. If your VCR is not SmartLink compatible, a message will be displayed to remind you to set your VCR timer.

• Once a recording has begun, you can switch the TV to standby mode, but do not turn off the TV completely or the recording may be cancelled.

• If an age restriction for programmes has been selected, a message asking for a PIN code will appear on the screen. For details, see “Parental Lock” on page 30.

1 Press F/f/G/g to select the future programme you want to

record, then press

2 Press 3 Press 4 Set the start and stop time in the same way as in step 3. 5 Press 6 Press to set the TV and your VCR timers.

To record the programme you are currently watching, press / .

1 Press / . 2 Press 3 Press

4 Press

5 Press G/g to select “Yes”, then press to confirm.

F/f to select “Manual timer REC”, then press . F/f to select the date, then press g.

F/f to select the programme, then press .

A red c symbol appears by that programme’s information. The indicator on the TV front panel lights up in orange.

F/f to select “Timer list”, then press . F/f to select the programme you want to cancel, then

press .

F/f to select “Cancel Timer”, then press .

A display appears to confirm that you want to cancel the programme.

/ .

Using the Digital Favourite list *

Favourite Set-up Enter Programme number - - Favourites 1

TV3

3/24

K3/300

TVE 1

TVE 2

24H TVE

CLAN TVE

TELEDEPORTE

VEO

Store favourite:

011

012

013

014

015

016

017

018

019

020

Favourites 2

Back:

SETenVEO

Tienda en VEO

NET TV

CUATRO

CNN+

40 LATINO

la Sexta

Telec inco

T5 Estrellas

T5 Sport

RETURN

Digital Favourite list

* This function may not be available in some countries/regions.

To Do this

Create your Favourite list for the first time

1 Press to select “Yes”. 2 Press yellow key to select favourite list. 3 Press

F/f to select the channel you want to add, then press

Channels that are stored in the Favourite list are indicated by a symbol.

Watch a channel

Turn off the Favourite list

Add or remove channels in the currently edited Favourite list

1 Press yellow key to navigate through favourite lists. 2 Press

F/f to select the channel, then press .

Press RETURN.

1 Press the blue button. 2 Press the yellow button to choose the list you want to edit. 3 Press

F/f to select the channel you want to add or remove,

then press .

The Favourite feature allows you to specify up to four lists of your favourite programmes.

1 Press MENU. 2 Press F/f to select “Digital Favourites”,

then press .

3 Perform the desired operation as shown in

the following table or displayed on the screen.

Watching TV

Remove all channels from the current Favourite list

1 Press the blue button. 2 Press the yellow button to select the favourite list you want to

edit.

3 Press the blue button. 4 Press

G/g to select “Yes”, then press to confirm.

Using Optional Equipment

Connecting optional equipment

You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.

Hi-Fi audio equipment

DVD player with component output

Video game

equipment

DVD player

Decoder

DVD recorder

VCR

Decoder

Audio system DVD player

PC (HDMI output) Blu-ray disc player Digital video camera

CAM card

For service use only

S VHS/Hi8/ DVC camcorder

Headphones

Viewing pictures from connected equipment

Switch on the connected equipment, then perform one of the following operation.

For equipment connected to the scart sockets using a fully-wired 21-pin scart lead

Start playback on the connected equipment. The picture from the connected equipment appears on the screen.

For an auto-tuned VCR (page 6)

In analogue mode, press PROG +/-, or the number buttons, to select the video channel.

For other connected equipment

Press / to display the connected equipment list. Press

F/f to select the desired input source, then press

. (The highlighted item is selected if 2 seconds pass

without any operation after pressing When the input source is set to “Skip” in the “AV Preset” menu under the “Set-up” menu (page 27), that input does not appear in the list.

Symbol on the screen

AV1/ AV1

AV2/ AV2

AV3 To see the equipment connected to

AV4 HDMI IN 4*.

* ~

• Be sure to use only an HDMI cable that bears the HDMI logo.

• When HDMI control compatible equipment is connected, communication with the connected equipment is supported. Refer to page 18 to set up this communication.

Description

To see the equipment connected to A.

To see the equipment connected to B.

SmartLink is a direct link between the TV and a VCR/DVD recorder.

To see the equipment connected to D. If the equipment has a DVI socket, connect the DVI socket to the HDMI IN socket through a DVI-HDMI adaptor interface (not supplied), and connect the equipment’s audio out sockets to the audio in HDMI IN sockets.

F/f.)

Symbol on the screen

AV5 or

AV5

PC To see the equipment connected

Description

To see the equipment connected to G.

To avoid picture noise, do not connect the camcorder to the video socket

5 and the S video socket 5 at the same time. If you connect mono equipment, connect to the L socket

to F.

It is recommended to use a PC cable with ferrites.

To connect Do this

Headphones H Connect to the i socket to listen to

sound from the TV on headphones.

Conditional Access Module (CAM) I

Hi-Fi audio equipment E

To use Pay Per View services. For details, refer to the instruction manual supplied with your CAM. To use the CAM, remove the rubber cover from the CAM slot. Switch off the TV when inserting your CAM into the CAM slot. When you do not use the CAM, we recommend that you replace the cover on the CAM slot.

CAM is not supported in all countries. Please check with your authorized dealer.

Connect to the audio output sockets

to listen to the sound from the TV

on Hi-Fi audio equipment.

Additional operations

To Do this

Return to normal TV mode

Access the Digital Favourites (in digital mode only)

Change the volume of the connected HDMI control compatible audio system

Mute the sound of the connected HDMI control compatible audio system

Press DIGITAL or ANALOG.

Press . For details, see page 15.

2 +/-.

Press

Press Press again to restore.

Using Optional Equipment

Using the Tools menu

Press TOOLS to display the following options when viewing pictures from connected equipment.

Using HDMI control

Options Description

Close Closes the Tools menu.

Picture Mode (except PC input mode)

Display Mode (in PC input mode only)

Sound Effect See page 22.

Speaker See page 23.

PIP (in PC input mode only)

H Centre (in PC input mode only)

V Lines (in PC input mode only)

Sleep Timer (except PC input mode)

Power Saving See page 24.

See page 20.

See page 18.

See page 25.

To view two pictures simultaneously – PIP (Picture in Picture)

You can view two pictures (PC input and TV programme) on the screen simultaneously. Connect a PC (page 16), and make sure that images from a PC appear on the screen.

You cannot display resolutions higher than WXGA (1280 × 768 pixels).

1 Press TOOLS to display the Tools menu. 2 Press F/f to select “PIP”, then press .

The picture from the connected PC is displayed with full size and the TV programme is displayed on the right corner. You can use screen position.

F/f/G/g to move the TV programme

3 Press number buttons or PROG +/- to

select the TV channel.

To return to single picture mode

Press RETURN.

You can switch the audible picture by selecting “PC Sound/ TV Sound” from the Tools menu.

The HDMI control function allows equipment to control each other using HDMI CEC (Consumer Electronics Control) specified by HDMI. You can perform interlocked control operations between Sony HDMI control compatible equipment such as a TV, DVD recorder with hard disk and audio system by connecting the equipment with HDMI cables. Be sure to correctly connect and set the compatible equipment to use the HDMI control function.

To connect the HDMI control compatible equipment

Connect the compatible equipment and the TV with an HDMI cable. When connecting an audio system, in addition to the HDMI cable, be sure to also connect the audio output socket system. For details, see page 16.

of the TV and the audio

To make the HDMI control settings

HDMI control must be set on both the TV side and the connected equipment side. See HDMI Set-up (page 27) for the TV side settings. See the operating instructions of the connected equipment for setting details.

HDMI control functions

• Turns the connected equipment off interlocked with the TV.

• Turns the TV on interlocked with the connected equipment and automatically switches the input to the equipment when the equipment starts to play.

• If you turn on a connected audio system while the TV is on, the input switches to the audio from the audio system.

• Adjusts the volume and mutes the sound of a connected audio system.

Using MENU Functions

Navigating through menus

“MENU” allows you to enjoy various convenient features of this TV. You can easily select channels or inputs sources and change the settings for your TV.

1 Press MENU. 2 Press F/f to select an option, then press

To exit the menu, press MENU.

5 External Inputs

Selects equipment connected to your TV.

• To watch the desired external input, select the input source, then press .

6 Settings

Displays the Settings menu where most of the advanced settings and adjustments are performed.

1 Press F/f to select a menu icon, then

press .

2 Press

For details about settings, see page 20 to 30.

The options you can adjust vary depending on the situation. Unavailable options are greyed out or not displayed.

* This function may not be available in some countries

regions.

F/f/G/g to select an option or

adjust a setting, then press .

Using MENU Functions

Digital Favourites

Select:

1 Digital Favourites*

Displays the Favourite list. For details about settings, see page 15.

2 Analogue

Returns to the last viewed analogue channel.

3 Digital*

Returns to the last viewed digital channel.

4 Digital EPG*

Displays the Digital Electronic Programme Guide (EPG). For details about settings, see page 13.

Enter:

Exit:

Picture Adjustment menu

Picture Adjustment

Picture Mode

Backlight

Contrast

Brightness

Colour

Hue

Sharpness

Colour Tone

Noise Reduction

Adv. Contrast Enhancer

Reset

Back:

Select:

Picture Mode

Display Mode

PC mode)

Backlight

(only in

You can select the options listed below on the Picture menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Enter:

Cinema

Max

Warm

Auto

Exit:

Selects the picture mode except for PC input source.

“Vivid”: For enhanced picture contrast and sharpness. “Standard”: For standard picture. Recommended for home entertainment. “Cinema”: For viewing film-based content. Most suitable for viewing in a theatre-

like environment. This picture setting was developed in collaboration with Sony Pictures Entertainment to faithfully reproduce movies as intended by their creators. Selects the display mode for PC input source.

“Video”: For video images. “Text”: For text, charts or tables.

Adjusts the brightness of the backlight.

Contrast

Brightness

Colour

Hue

Sharpness

Colour Tone

Increases or decreases picture contrast.

Brightens or darkens the picture.

Increases or decreases colour intensity.

Increases or decreases the green tones.

“Hue” can only be adjusted for an NTSC colour signal (e.g., U.S.A. video tapes).

Sharpens or softens the picture.

Adjusts the whiteness of the picture.

“Cool”: Gives the white colours a blue tint. “Neutral”: Gives the white colours a neutral tint. “Warm”: Gives the white colours a red tint.

“Warm” can not be selected when you set “Picture Mode” to “Vivid”.

+ 46 hidden pages