To Customers
For product protection and safety reasons, Sony strongly recommends that installation of your TV or
LCD Display be performed by Sony dealers or licensed contractors. Do not attempt to install it
yourself.
To Sony Dealers and Contractors
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Sufficient expertise is required for installing this product, especially to determine the
strength of the wall for withstanding the TV’s or LCD Display's weight. Be sure to
entrust the attachment of this product to the wall to Sony dealers or licensed
contractors and pay adequate attention to safety during the installation. Sony is not
liable for any damage or injury caused by mishandling or improper installation.
For Safety and proper installation, follow the Wall-Mount Bracket Operation Instructions, TV or LCD
Display Setup Guide and the directions in this manual.
− 2 (US) −
Wall-Mount Bracket
On Safety
Thank you for purchasing this product.
To Customers
Installing the TV or LCD Display to the
Wall
WARNING
PROFESSIONAL INSTALLATION
REQUIRED
This product should only be installed by
a professional installer who is trained to
determine the strength of the wall for
withstanding the TV’s or LCD Display's
weight. If it is not properly secured
during installation, the TV or LCD Display
may fall and cause serious injury. Sony is
not liable for any damage or injury
caused by mishandling or improper
installation, or installing any other than
the specified product. Your Statutory
Rights (if any) are not affected.
To Sony Dealers
Sufficient expertise is required for
installing this product. Be sure to read
this instruction manual thoroughly to do
the installation work safely. Sony is not
liable for any damages or injury caused
by mishandling or improper installation.
Please give this manual to the customer
after installation.
This instruction manual shows the correct
handling of the product and important
precautions necessary to prevent accidents.
It is your responsibility to read, thoroughly
understand, and follow all instructions in this
instruction manual. Failure to do so may
result in serious personal injury or property
damage, and may void the warranty. Keep
this manual available for future reference.
Products by Sony are designed with safety in
mind. If the products are used incorrectly,
however, it may result in a serious injury
through fire, electric shock, the product
toppling over, or the product dropping. Be
sure to observe the precautions for safety to
prevent such accidents.
CAUTION
Specified products
This Wall-Mount Bracket is designed for use
with the products specified TVs or LCD
Displays. For TVs or LCD Displays, refer to
their Reference Guide to verify that the
Wall-Mount Bracket can be used.
To Customers
WARNING
If the following precautions are not
observed, serious injury or death
through fire, electric shock, or the
product dropping can result.
Be sure to subcontract
the installation to
licensed contractors and
keep small children away
during the installation.
If the Wall-Mount Bracket or the TV or LCD
Display is not installed correctly, the
following accidents may occur. Be sure
licensed contractors carry out installation.
The TV or LCD Display may fall and cause a
serious injury such as a bruise or a fracture.
If the wall on which the Wall-Mount
Bracket is installed is unstable, uneven, or
not perpendicular to the floor, the unit
may fall and cause injury or property
damage. The wall should be capable of
supporting a weight of at least six times
the TV or LCD Display weight.
(Refer to your TV’s or LCD Display's
Reference Guide for its weight.)
If the installation of the Wall-Mount
Bracket on the wall is not sufficiently
sturdy, the unit may fall and cause injury or
property damage.
Be sure to subcontract
moving or dismounting
of the TV or LCD Display
to licensed contractors.
If persons other than licensed contractors
transport or dismount the TV or LCD Display,
it may fall and cause injury or property
damage. Two or more persons (three or
more persons for 189.3 cm (75 inches) and
above TV or LCD Display) are needed to
transport a large TV or LCD Display.
Do not remove screws,
etc., after mounting the
TV or LCD Display.
If you do so, the TV or LCD Display may fall
and cause injury or property damage.
Do not make alterations
to the parts of the WallMount Bracket.
If you do so, the Wall-Mount Bracket may fall
and cause injury or property damage.
Do not mount any
equipment other than
the specified product.
This Wall-Mount Bracket is designed for use
with the specified product only. If you mount
equipment other than specified, it may fall or
break, and cause injury or property damage.
Do not apply any load
other than the TV or LCD
Display on the WallMount Bracket.
Do not shake the TV or
LCD Display left/right,
up/down.
If you do so, the TV or LCD Display may fall
and cause injury or property damage.
Do not lean on or hang
from the TV or LCD
Display.
Do not lean on or hang from the TV or LCD
Display as it may fall on you and cause
serious injury.
CAUTION
If the following precautions are not
observed, injury or property damage
may occur.
Be careful to not pinch your fingers while
handling the Wall-Mount Bracket or
swiveling the TV or LCD Display.
While swiveling the TV or LCD Display,
handle it with caution and take care not to
hit any people nearby.
Be sure to store the unused parts in a safe
place for future use.
Keep them away from children.
Do not handle the
product with excessive
force during cleaning or
maintenance.
Do not apply excessive force on the topside
of the TV or LCD Display. If you do so, the TV
or LCD Display may fall and cause injury or
property damage.
Do not place this product
close to medical devices.
This product (including accessories) has
magnet(s) which may interfere with
pacemakers, programmable shunt valves for
hydrocephalus treatment, or other medical
devices. Do not place this product close to
persons who use such medical devices.
Consult your doctor before using this
product if you use any such medical device.
Keep out of the reach of
children or the
supervised individuals.
This product (including accessories) has
magnet(s). Swallowing magnet(s) could
cause serious harm, such as choking hazard
or intestinal injuries. If magnets (or a
magnet) were swallowed, consult a doctor
immediately.
US
− 3 (US) −
Notice
If you use the TV or LCD Display installed
on the Wall-Mount Bracket for a long time,
the wall behind or above the TV or LCD
Display may become discolored or the
wallpaper may come unstuck, depending
on the material of the wall.
If the Wall-Mount Bracket is removed after
installing it on the wall, the screw holes are
left.
Do not use the Wall-Mount Bracket in a
place where it is subjected to mechanical
vibrations.
Be sure to install the
Wall-Mount Bracket
securely to the wall
following the instructions
in this instruction
manual.
If any of the screws are loose or fall out, the
Wall-Mount Bracket may fall and cause injury
or property damage. Be sure to use the
appropriate screws for the material of the
wall and install the unit securely using
supplied screws and anchors.
Be sure to tighten the
screws securely in the
designated position.
If you fail to do so, the TV or LCD Display may
fall and cause bodily injury to someone or
damage to the TV or LCD Display.
Be careful not to subject
the TV or LCD Display to
shock during installation.
If the TV or LCD Display is exposed to shock,
it may fall or break apart. This may cause
injury.
Installing the WallMount Bracket
To Sony Dealers
WARNING
The following instructions are for Sony
dealers only. Be sure to read safety
precautions described above and pay
special attention to safety during the
installation, maintenance and checking
of this product.
Do not install the WallMount Bracket on wall
surfaces where the
corners or the sides of
the TV or LCD Display
protrude away from the
wall surface.
Do not install the Wall-Mount Bracket on wall
surfaces such as a pillar, where the corners
or the sides of the TV or LCD Display
protrude away from the wall surface. If a
person or object happens to hit the
protruded corner or side of the TV or LCD
Display, it may cause injury or property
damage.
Be sure to use the
supplied screws and
attachment parts
properly following the
instructions given in
this instruction
manual. If you use
substitute items, the
TV or LCD Display may
fall and cause bodily
injury to someone or
damage to the TV or
LCD Display.
Be sure to install the TV
or LCD Display on a wall
that is both
perpendicular and flat.
If you fail to do so, the TV or LCD Display may
fall and cause injury.
After proper installation
of the TV or LCD Display,
secure the cables
properly.
If people or objects get tangled with cables,
this may result in injury or damage to the TV
or LCD Display.
Do not allow the AC
power cord or the
connecting cable to be
pinched.
If the AC power cord or the connecting cable
is pinched between the unit and the wall or
is bent or twisted by force, the internal
conductors may become exposed and cause
a short circuit or an electrical break. This may
cause a fire or an electric shock.
Do not install the TV or
LCD Display over or
under an air-conditioner.
If the TV or LCD Display is exposed to water
leaks or air current from an air conditioner
for a long time, it may cause a fire, an electric
shock or a malfunction of the TV or LCD
Display.
Be sure to assemble the
bracket properly
following the instructed
procedure explained in
this instruction manual.
If any of the screws are loose or fall out, the
TV or LCD Display may fall and cause bodily
injury to someone or damage to the TV or
LCD Display.
− 4 (US) −
Before Getting Started
The TV or LCD Display illustrations shown in this manual are examples used to provide clear
explanations of the operations. For this reason, the illustrations may appear different from your
actual TV or LCD Display.
What Is Your Wall Made Of?
Firstly, check the type of the wall to install the TV or LCD Display.
The Wall-Mount Bracket differs depending on the type of the wall.
Dry wall with studs
Precautions
Maximum dry wall thickness:
16mm (21/32 inch).
Ensure that the inner wood stud size is at
least 51mm×102mm (21/8inch ×
41/8inch) for common or 38mm×89mm
(11/2inch × 35/8inch) for nominal.
Keep minimum 406mm (16 inch) horizontal
space between fasteners.
Use the Lateral Shift Bracket.
Solid concrete or concrete block
Precautions
Mount the Wall-Mount Bracket directly onto
the solid concrete wall.
Ensure that the thickness of solid concrete
wall is at least 203mm (8 inch).
Ensure that the size of each concrete block is
at least 203mm×203mm×406mm (8inch
× 8inch ×16 inch).
Use the Wall-Mount Bracket.
US
+
− 5 (US) −
Checking the Parts
WS1
Supplied with SU-WL855
Verify that all the parts are included.
(×1)
WM1
M6
(×4)
6mm × 20mm
(1/4inch × 13/16inch)
WW1
(×6)
WT1
(×6)
(×1)
WM2
(×4)
8mm × 12mm
(11/32inch × 1/2inch)
WW2
(×4)
(×4)
WM3
WM4
(×1)
(×6)
WS2
8mm × 60mm
(11/32inch × 23/8inch)
WA1
(×4)
Supplied with the TV or LCD Display
Wall-Mount Attachment
(×4)*
VS
* Only for limited region/country/model.
− 6 (US) −
Preparing for Installation
Have the TV’s or LCD Display's Reference Guide and Setup Guide at hand before installation.
Confirm the installing position of your TV or LCD Display.
Prepare the following tools:
*1
5.5mm
(7/32inch)
10mm
(13/32inch)
*2*3
1.5N·m/1,5N·m
{15kgf·cm}
13mm (1/2inch)
12.5N·m/12,5N·m
{130kgf·cm}
*1 Only for dry wall with studs
US
1.5N·m/1,5N·m
{15kgf·cm}
*2 Only for solid concrete or concrete block
*3 Depending on models
− 7 (US) −
Attaching the Wall-Mount
× 2
Bracket to the Dry Wall with Studs
WM4
2
3 Align
four marks aligned with the
studs.
WM4
to the wall and make
WM1
Installing the Lateral Shift
Bracket to the Wall
1 Decide on the installation
location.
Make sure that the wall has enough space
for the TV or LCD Display and is capable of
supporting a weight of at least six times
that of the TV or LCD Display.
• Refer ”Measurement for Lateral Shift
Bracket installation on the wall“ on page
20.
• Refer to your TV’s or LCD Display's
Reference Guide for the TV’s or LCD
Display's weight.
Note
When your TV or LCD Display is installed on the
wall, the upper side of the TV or LCD Display
slightly leans forward.
We recommend you to check the position of TV or
LCD Display in the viewing environment.
× 4
Note
Use a level to check whether
WM4
WM4
is level.
4 Drill upper pilot holes on the
marks.
Make sure the location on the wall to drill
the holes are strong enough to support a
weight of at least six times that of the TV or
LCD Display.
5.5 mm
(7/32 inch)
75 mm
(3 inch)
Note
Pilot holes must be drilled to a depth of 75mm
(3inch), using a 5.5mm (7/32inch) diameter drill
bit.
− 8 (US) −
5 Install
× 2
WM4
on the wall.
WW1WS2WM4
8
WM1
WW2
WS1
Note
Use a level to check whether
Precaution
Do not over-tighten the lag bolts
tightening could reduce the holding power of the
lag bolts
WS2
.
WM4
WS2
is level.
. Improper
6 Drill lower pilot holes on the
marks. (Refer step 4 for the drill
instruction.)
× 2
7 Fit the screws and spacers to the
holes.
WM4
9 Pull out the arm of the bracket to
the end.
Preparing for the Installation
of the TV or LCD Display
Note
Be sure to store the removed screws and unused parts
in a safe place, keeping them away from children.
US
WS2
Note
Use a level to check whether
WW1
WM4
× 2
is level.
1 Attach the Table-Top Stand to
make the TV or LCD Display
standing.
• Refer to your TV’s or LCD Display's Setup
Guide.
− 9 (US) −
2 Remove the screws from the rear
VS
VS
of the TV or LCD Display.
3 Attach the Wall-Mount
Attachment
the TV or LCD Display) to the
rear of the TV or LCD Display (to
make it parallel with the wall).
VS
(supplied with
1.5N·m/1,5 N·m
VS
{15kgf·cm}
5 Attach
Display using
WM2
to the TV or LCD
M6
.
WM2
M6
6 Detach the Table-Top Stand from
the TV or LCD Display.
The following illustration is an example of
the operation.
• Remove one side of the Table-Top Stand
at a time. Firmly hold the Table-Top Stand
securely with both hands while the other
people lift up the TV or LCD Display.
Note
Be sure to fasten the Wall-Mount Attachment
when attaching them to the TV or LCD
VS
Display.
Use only a flat head screwdriver to install the
Wall-Mount Attachment
might result in over torqueing the Wall-Mount
Attachment
Display.
4 Attach
WM3
Note
Do not attach
and damaging the TV or LCD
WM3
.
WM3
. Use of another tool
on the labels.
• Repeat the previous step and remove the
other side of the Table-Top Stand.
• Remove one side of the Table-Top Stand
at a time. Firmly hold the Table-Top Stand
securely with both hands while the other
people lift up the TV or LCD Display.
• Repeat the previous step and remove the
other side of the Table-Top Stand.
Note
Three or more people are required to detach the
Table-Top Stand.
Be careful not to use excessive force while
detaching the Table-Top Stand from the TV or LCD
Display as it may cause the TV or LCD Display to fall
resulting in personal injury or physical damage to
the TV or LCD Display.
Take care when handling the Table-Top Stand to
prevent damage to the TV or LCD Display.
Be careful when lifting the TV or LCD Display as the
Table-Top Stand is detached, the Table-Top Stand
may topple over and cause personal injury.
Take care when removing the Table-Top Stand from
the TV or LCD Display to prevent it from falling over
and damaging the surface that the TV or LCD
Display is sitting on.
Installing the TV or LCD
Display on the Wall
1
US
− 11 (US) −
2
3 Screw the left and right side of
the Wall-Mount Bracket.
4
5 When moving the TV or LCD
Display, hold it firmly from the
bottom.
M6
M6
Note
The TV or LCD Display may not move near close to
the wall depending on the type and number of
cables attached. This is not a malfunction.
6
− 12 (US) −
WARNING
Two or more persons (three or more persons for
189.3cm (75inches) and above TV or LCD Display) are
needed to transport a large TV or LCD Display.
Confirming the Completion of
the Installation
Check the following points.
The cord and the cable are not twisted or
pinched.
WARNING
Improper placement of the AC power cord, etc. may
cause fire or electric shock through a short circuit. Be
sure to confirm the completion of the installation for
safety.
Other Information
When removing the TV or LCD Display, reverse
the previous installation procedure.
WARNING
Two or more persons (three or more persons for
189.3cm (75inches) and above TV or LCD Display) are
needed to transport a large TV or LCD Display.
Attaching the Wall-Mount
Bracket to the Solid Concrete or
Concrete Block
WM1
Installing the Wall-Mount
Bracket to the Wall
1 Decide on the installation
location.
Make sure that the wall has enough space
for the TV or LCD Display and is capable of
supporting a weight of at least six times
that of the TV or LCD Display.
• Refer ”Measurement for Wall-Mount
Bracket installation on the wall“ on page
22.
• Refer to your TV’s or LCD Display's
Reference Guide for the TV’s or LCD
Display's weight.
Note
When your TV or LCD Display is installed on the
wall, the upper side of the TV or LCD Display
slightly leans forward.
We recommend you to check the position of TV or
LCD Display in the viewing environment.
US
− 13 (US) −
2 Align
WS2
WW1
WM1
four marks.
× 4
WM1
to the wall and make
WM1
5 Install
WM1
on the wall.
Note
Use a level to check whether
WM1
is level.
3 Drill pilot holes on the marks.
Make sure the location on the wall to drill
the holes are strong enough to support a
weight of at least six times that of the TV or
LCD Display.
× 4
10 mm
(13/32 inch)
75 mm
(3 inch)
Note
Pilot holes must be drilled to a depth of 75mm
(3inch), using a 10mm (13/32inch) diameter drill
bit.
4
Note
Use a level to check whether
Precaution
Do not over-tighten lag bolts
tightening could reduce the holding power of lag
WS2
bolts
.
WM1
WS2
is level.
. Improper
6 Pull out the arm of the bracket to
the end.
WA1
− 14 (US) −
Preparing for the Installation
VS
VS
WM3
of the TV or LCD Display
Note
Be sure to store the removed screws and unused parts
in a safe place, keeping them away from children.
Note
Be sure to fasten the Wall-Mount Attachment
when attaching them to the TV or LCD
Display.
Use only a flat head screwdriver to install the
Wall-Mount Attachment
might result in over torqueing the Wall-Mount
Attachment
Display.
and damaging the TV or LCD
VS
. Use of another tool
1 Attach the Table-Top Stand to
make the TV or LCD Display
standing.
• Refer to your TV’s or LCD Display's Setup
Guide.
2 Remove the screws from the rear
of the TV or LCD Display.
4 Attach
WM3
Note
Do not attach
5 Attach
Display using
WM3
.
on the labels.
WM2
to the TV or LCD
M6
.
WM2
US
3 Attach the Wall-Mount
Attachment
the TV or LCD Display) to the
rear of the TV or LCD Display (to
make it parallel with the wall).
VS
(supplied with
1.5N·m/1,5 N·m
VS
{15kgf·cm}
M6
− 15 (US) −
6 Detach the Table-Top Stand from
the TV or LCD Display.
The following illustration is an example of
the operation.
• Remove one side of the Table-Top Stand
at a time. Firmly hold the Table-Top Stand
securely with both hands while the other
people lift up the TV or LCD Display.
• Repeat the previous step and remove the
other side of the Table-Top Stand.
• Remove one side of the Table-Top Stand
at a time. Firmly hold the Table-Top Stand
securely with both hands while the other
people lift up the TV or LCD Display.
• Repeat the previous step and remove the
other side of the Table-Top Stand.
Note
Three or more people are required to detach the
Table-Top Stand.
Be careful not to use excessive force while
detaching the Table-Top Stand from the TV or LCD
Display as it may cause the TV or LCD Display to fall
resulting in personal injury or physical damage to
the TV or LCD Display.
Take care when handling the Table-Top Stand to
prevent damage to the TV or LCD Display.
Be careful when lifting the TV or LCD Display as the
Table-Top Stand is detached, the Table-Top Stand
may topple over and cause personal injury.
Take care when removing the Table-Top Stand from
the TV or LCD Display to prevent it from falling over
and damaging the surface that the TV or LCD
Display is sitting on.
− 16 (US) −
Installing the TV or LCD
Display on the Wall
1
2
3 Screw the left and right side of
the Wall-Mount Bracket.
M6
US
− 17 (US) −
M6
4
5 When moving the TV or LCD
Display, hold it firmly from the
bottom.
WARNING
Two or more persons (three or more persons for
189.3cm (75inches) and above TV or LCD Display) are
needed to transport a large TV or LCD Display.
Confirming the Completion of
the Installation
Check the following points.
The cord and the cable are not twisted or
pinched.
Note
The TV or LCD Display may not move near close to
the wall depending on the type and number of
cables attached. This is not a malfunction.
6
WARNING
Improper placement of the AC power cord, etc. may
cause fire or electric shock through a short circuit. Be
sure to confirm the completion of the installation for
safety.
Other Information
When removing the TV or LCD Display, reverse
the previous installation procedure.
WARNING
Two or more persons (three or more persons for
189.3cm (75inches) and above TV or LCD Display) are
needed to transport a large TV or LCD Display.