Sony IPELA HYBRID SNC-ZB550, IPELA SNC-CH120, IPELA SNC-EB520, IPELA SNC-CH220, IPELA SNC-CH115 Installation Manual

4-199-272-17(1)

U1/4”, 20 UNC

= 4.5 mm to 7 mm
(ISO standard) (with the
screws fastened)



   

  

Network Camera

Installation Manual

Before operating the unit, please read this manual thoroughly and
retain it for future reference.

SNC-CH115/CH120/CH220
SNC-EB520/ZB550

2010 Sony Corporation Printed in China



Owner’s Record

The model and serial numbers are located on the top. Record these numbers
in the spaces provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding
this product.

Model No. Serial No.

Overview

This Installation Manual gives instructions for multiple types of Network
Cameras: SNC-CH115/CH120/CH220 are PoE-type HD models, SNC-EB520 is a
PoE-type SD model, and SNC-ZB550 is an HD model IPELA HYBRID camera.

WARNING

To reduce a risk of fire or electric shock, do not expose
this product to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.

WARNING

This installation should be made by a qualified service person and should
conform to all local codes.

Power Supply

Caution for U.S.A. and Canada (SNC-ZB550)

The SNC-ZB550 operates on 24 V AC or 12 V DC.
The SNC-ZB550 automatically detects the power.
In the USA, this product shall be powered by a UL listed Class 2 Power Supply
Only.
In Canada, this product shall be powered by a CSA Certified Class 2 Power
Supply Only.

Caution for other countries (SNC-ZB550)

The SNC-ZB550 operates on 24 V AC or 12 V DC.
The SNC-ZB550 automatically detects the power.
Use a power supply rated 24 V AC or 12 V DC which meets the requirements
for SELV (Safety Extra Low Voltage) and complies with Limited Power Source
according to IEC 60950-1.

CAUTION for LAN port

For safety reason, do not connect the LAN port to any network devices that
might have excessive voltage.

CAUTION for LAN port (SNC-CH115/CH120/CH220/EB520)

The LAN port of this unit is to be connected only to the devices whose
power feeding meets the requirements for SELV (Safety Extra Low Voltage)
and complies with Limited Power Source according to IEC 60950-1.
Use IEEE802.3af standard compliant devices.

For customers in the U.S.A.

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved
in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to
comply with the limits for a digital device pursuant to Subpart B of Part 15 of
FCC Rules.

For customers in Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.

For the customers in Europe

The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato­ku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to the addresses given in
separate service or guarantee documents.

For the customers in Europe, Australia and New Zealand

WARNING

This is a Class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
In the case that interference should occur, consult your nearest authorized
Sony service facility.
This apparatus shall not be used in the residential area.

ATTENTION

The electromagnetic fields at specific frequencies may influence the picture
of the unit.

Notes on Use

Before Use

If you find condensation when you open the package, turn on the power after



the condensation disappears.
Remove the static electricity before operation or when touching the camera.



Data and security

You should keep in mind that the images or audio you are monitoring may be



protected by privacy and other legal rights, and the responsibility for making
sure you are complying with applicable laws is yours alone.
Access to the images and audio is protected only by a user name and the



password you set up. No further authentication is provided nor should you
presume that any other protective filtering is done by the service. Since
the service is Internet-based, there is a risk that the image or audio you are
monitoring can be viewed or used by a third-party via the network.
SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU



OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR
EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY
DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.
Always make a test recording, and verify that it was recorded successfully.



SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT
LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE
OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR
ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.
Always verify that the unit is operating properly before use. SONY WILL NOT



BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY
OTHER REASON WHATSOEVER.
If you lose data by using this unit, SONY accepts no responsibility for



restoration of the data.

Personal information

The images taken by the system using this device can identify individuals



and thus they fall under “personal information” stipulated in the “Act on
the Protection of Personal Information”. Please handle the video data
appropriately according to law.
Information recorded using this product may also be “personal information”.



Upon disposal, transfer, repair, or any other occasion where this product or
storage media is passed on to a third party, practice due care in its handling.

Operating or storage location

Avoid operating or storing the camera in the following locations.

Extremely hot or cold places (Operating temperature: –10°C to +50°C [14°F to



122°F])
Exposed to direct sunlight for a long time, or close to heating equipment (e.g.,



near heaters)
Close to sources of strong magnetism



Close to sources of powerful electromagnetic radiation, such as radios or TV



transmitters
Locations subject to strong vibration or shock



Humid or dusty locations



Locations exposed to rain



Locations under the influence of fluorescent light or reflection of a window



Under an unsteady light (The image will flicker.)



Ventilation

To prevent heat buildup, do not block air circulation around the camera.

Power supply (SNC-CH115/CH120/CH220/EB520)

The power of this model is supplied by network cable.



Use the network cable UTP, category-5.



Damage to the network cable may result in fire or electric shock.



Transportation

Always turn off the power when carrying.



When transporting the camera, repack it as originally packed at the factory or



in materials of equal quality.

Cleaning

Use a blower to remove dust from the lens.



Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn



stains can be removed using a soft cloth dampened with a small quantity of
detergent solution, then wipe dry.
Do not use volatile solvents such as alcohol, benzene or thinners as they may



damage the surface finishes.

Note on laser beams

Laser beams may damage image sensors. You are cautioned that the surface of image
sensors should not be exposed to laser beam radiation in an environment where a laser
beam device is used.

Phenomena Specific to Image Sensors

The following phenomena that may occur in images are specific to image
sensors. They do not indicate a malfunction.

White flecks

Although the image sensors are produced with high-precision technologies, fine
white flecks may be generated on the screen in rare cases, caused by cosmic rays,
etc.
This is related to the principle of image sensors and is not a malfunction.
The white flecks especially tend to be seen in the following cases:

- when operating at a high environmental temperature

- when you have raised the gain (sensitivity)

- when using the slow shutter

Aliasing

When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.

About the Supplied Manuals

Installation Manual (this document)

This Installation Manual describes the names and functions of parts and controls
of the Network Camera, gives connection examples and explains how to set up
the camera. Be sure to read the Installation Manual before operating.
The pictures of an SNC-CH220 camera are used in the explanatory examples.

User’s Guide (stored in the CD-ROM)

The User’s Guide describes how to set up the camera and how to control the
camera via a Web browser.
After installing and connecting the camera correctly, operate referring to this
User’s Guide.

Using the CD-ROM Manuals

The supplied CD-ROM disc includes the User’s Guides for this unit in PDF format.

Preparations

The Adobe Reader Version 6.0 or higher must be installed on your computer in
order to use the guides stored in the CD-ROM disc.

Note

If Adobe Reader is not installed, it may be downloaded from the following URL:
http://www.adobe.com/

Reading the manual in the CD-ROM

1 Insert the CD-ROM in your CD-ROM drive.

A cover page appears automatically in your Web browser.

If it does not appear automatically in the Web browser, double-click on the
index.htm file on the CD-ROM.

2 Select and click on the manual that you want to read.

This opens the PDF file of the manual.

Clicking an item in the Table of Contents allows you jump to the relevant
page.

Notes

The files may not be displayed properly, depending on the version of Adobe



Reader. In this case, install the latest version, which you can download from
the URL mentioned in “Preparations” above.
If you have lost or damaged the CD-ROM, you can purchase replacement.



Contact your Sony service representative.

Smartphone viewer

This product is equipped with a Smartphone viewer.
With Smartphone viewer, you can display an image from a network camera, pan,
tilt and zoom that camera, on your smartphone.
For more details, see “Smartphone viewer User’s Manual” at the following URL:
http://www.sony.net/ipela/snc

Location and Function of Part

Front 

 Lens

A vari-focal lens is mounted as standard equipment.

 Focus ring

Turn this ring toward N (near) to focus on a closer object. Turn it toward F or
infinite to focus on a farther object.

 Zoom ring

Turn this ring toward T for telephoto, or toward W for wide-angle.

 Tripod screw hole

Use this screw hole when attaching the camera
to a tripod.

Caution

Use the mounting screw whose length is 4.5 mm (3/ inch) to 7 mm
(9/ inch) only. Use of other screws may cause improper mounting and
damage parts inside the camera.

 Rating Label

This label shows the name of device and its electric rating.

 Lens connector (4-pin socket)

Supplies power and control signals to an auto-iris lens.

 Lens mount (SNC-CH115 only)

Use to mount an appropriate CS-mount lens.
Use the C mount adaptor (optional) when you use the C-mount lens.
(A vari-focal lens is mounted as the standard equipment for SNC-CH120/

CH220/EB520/ZB550.)

SNC-CH120/CH220/EB520/ZB550

Rear 

 I/O (Input/Output) port

This cable is provided with a sensor input and an alarm output.
The wires of the cable control the following signals.

SNC-CH115/CH120/CH220/EB520

PinNo. Signal

1 Alarm output 1–
2 Alarm output 1+
3 Sensor input– (GND)
4 Sensor input+

SNC-ZB550

PinNo. Signal

1 Sensor input+
2 Sensor input– (GND)
3 Alarm output 1+
4 Alarm output 1–

 For details on each function and required settings, see the User’s

Guide stored in the supplied CD-ROM.

 For the wiring, see “Connecting the I/O cable.”

 LAN network port (RJ-45)

Use the network cable (UTP, category-5) for network communications
and PoE* power supply.

However, the PoE power supply feature is not available on SNC-ZB550.
 See “Connect to the Network” for connection.
(* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard

compliant devices.)

 Easy Focus button

Press this button to automatically adjust the focus.
To load the default setting, press and hold this button for 4 seconds.

 Fall-prevention wire rope mounting screw hole

When installing the camera to the ceiling or the wall, secure the supplied
wire rope to this hole using the supplied screw.

 NETWORK indicator (Green/Orange)

The indicator lights up or flashes when the camera is connected to the
network. The indicator is off when the camera is not connected to the
network. When 100BASE-TX is connected, the indicator turns green.
When 10BASE-T is connected, the indicator turns orange.

The indicator also turns green when SLOC (IP coaxial transfer) is selected.

 Reset switch

To reset the camera to the factory default settings, turn on the power to
the camera while holding down this switch with a pointed object.

 POWER indicator (Green)

When the power is supplied to the camera, the camera starts checking
the system. If the system is normal, this indicator lights up.

 NTSC/PAL switch

Switching the video output.

 MONITOR output jack

Output the composite video signal from the camera.
Monitor out is used when you adjust the angle of view. Be sure to set

monitor out to on when you use it. Set it to off and disconnect the video
cable when you do not use it.

For details on system setting, see the User’s Guide.

Notes

Do not connect to the video cable until the POWER indicator lights



up.
Be aware that the system performance may be influenced, if



monitor out is set to on. Be sure to set it to off and disconnect the
video cable when you do not use it.

 DC 12 V/ AC 24 V (power input) terminal

Connect to a 12 V DC or 24 V AC power supply system.

 Network connection change switch

Use this switch to change between a network connection to a LAN
(network) port (RJ-45) and a network connection using a coaxial cable.

 SLOC (IP coaxial transfer/video output) port

Use this port when connecting the unit to a network using a coaxial
cable. When using a composite signal, set the network connection
change switch to LAN.

Also use this port to output composite video signals from this unit.
A connection to compatible equipment is necessary when connecting to

a network using a coaxial cable.
For connection details, refer to the instruction manuals of the equipment

on the receiving end.

Note

The output analog image may not display correctly, depending on
the video format and image size settings.

The image may not display properly in the horizontal and/or



vertical plane.
The image may be reduced.



  (ground) terminal

This is a ground terminal for the chassis.

(continued on the reverse side)

SNC-CH115/CH120/CH220/EB520

SNC-ZB550

SNC-CH115

CS-mount lens

5.5 (/) or less

Wire rope (supplied)

When Easy Focus button is pressed

The number indicates
the focus position.

* mark indicates the

approximate focus position.

SNC-CH115/CH120/CH220/EB520

10BASE-T/
100BASE-TX

SNC-ZB550

DC 12V/AC 24V

+−

+ −

Network cable
(straight, not
supplied)

Network

SLOC-compatible
device

Video output terminal

Coaxial cable

Unit: mm (inch)

Screw
(supplied)

Network cable
(straight, not
supplied)

PoE supported
device (such as
a hub)

LAN Coaxial cable

Coaxial cable
maximum length:
RG-59 300 meters

10BASE-T/
100BASE-TX

Hub

SLOC
connector

LAN port
(RJ-45)

Network cable
10BASE-T/
100BASE-TX

Front (SNC-CH120/CH220/
/ZB550)

72 (2 /)

63 (2 /)

62 (2 /)

Front (SNC-EB520)

72 (2 /)

63 (2 /)

62 (2 /)

Side (SNC-CH120/CH220)

SNC-CH120 : 52 (2 /)
SNC-CH220 : 52.3 (2 /)

43 (1 /4)

55 (2 /4)

Side (SNC-CH115)

145 (5 /4)

43 (1 /4)

55 (2 /4)

140 (5 /)

Side (SNC-EB520)

42.8 (1 /16)

43 (1 /4)

55 (2 /4)

Side (SNC-ZB550)

52 (2 /8)

43 (1 /4)

55 (2 /4)

Front (SNC-CH115)

63 (2 /)

145 (5 /4)
140 (5 /)

145.6 (5 /4)

145.6 (5 /4)

145 (5 /4)
140 (5 /)

145.6 (5 /4)

145 (5 /4)
140 (5 /)

150.5 (6)

72 (2 /)

62 (2 /)

Unit: mm (inch)

Installation

Caution

If you attach the camera in a high location such as wall or ceiling, etc.,



entrust the installation to an experienced contractor or installer.
If you install the camera in a high location, ensure that the ceiling is strong



enough to withstand the weight of the camera plus mounting brackets
and screws, and then install the camera securely. If the ceiling is not strong
enough, the camera may fall and cause serious injury.
To prevent the camera from falling, make sure to attach the supplied wire



rope.
If you attach the camera to the ceiling, check periodically, at least once a



year, to ensure that the connection has not loosened. If conditions warrant,
make this periodic check more frequently.

Suitable lens 

The lens must be a CS-mount type and the protrusion behind the mounting
surface must be 5.5 mm (/ inch) or less.

Caution

Keep the lens mount cap on the camera when it is not attached the lens.



When you install it into a wall or a ceiling, check that the wall or the ceiling



is strong enough to hold the weight of the camera including the mounting
bracket, and install it without fail. If not, the camera falls down and causes
a serious injury. Also, check if the mounting is not loosened at least once a
year. Make the checking interval short according to use condition.
Performance will depend on the installation environment and the lens



itself. For details, contact your authorized Sony dealer.

Attaching the wire rope 

When you install the camera on a ceiling or a high position, be sure to attach the
supplied wire rope to prevent the camera from falling.
Attach the wire rope to the screw hole on the rear of the camera, as in the
illustration.

Note

Take care not to short-circuit the cable with the wire rope when you attach it.

1 Secure the wire rope to the junction box on the ceiling.

Use a screw to match the screw hole of your junction box (not supplied).

2 Secure the wire rope to the wire rope mounting screw hole on the rear of

the camera using the supplied screw.

Note

Use the supplied screws to install the unit. Using other screws may cause
damage inside the unit.

Adjusting the Camera Coverage and Focus 

1 Loosen the zoom ring locking screw to adjust the camera shooting

coverage.

2 Tighten the locking screw to fix the zoom.
3 Loosen the focus ring locking screw to adjust the focus.
4 Tighten the locking screw to fix the focus.
5 Press the Easy Focus button on the rear to automatically adjust the

focus.

Note

You may not achieve satisfactory focus with the Easy Focus button due to the
shooting environment.
In this condition, press and hold Easy Focus button for more than 4 seconds to
return to the default flange back position. Then, adjust the focus following
step 3 and 4.

Connection

Connect to the Network

SNC-CH115/CH120/CH220/EB520

Connect the LAN connector of the camera to a PoE* supported device (such as a
hub) using the network cable (straight, not supplied).
The electrical power is supplied through the network cable. For details, refer to
the instruction manuals of the PoE supported devices.
(* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard compliant
devices.)

SNC-ZB550 

Connect to a network using a coaxial cable or LAN.

Connecting via a coaxial cable



When the network connection change switch is set to SLOC, connect to a
network via a coaxial cable.
The maximum coaxial cable length is RG-59 300 m.

Note

The high-frequency characteristics of coaxial cables may differ, even if the



cables are of the same classification. Use a high-quality, high-frequency
coaxial cable with this unit.
 For details, refer to the instruction manual of the connecting SLOC

device. For further details, please consult an authorized Sony dealer.

When connecting with a coaxial cable, do not connect a network cable to



this unit.

Connecting via LAN



When the network connection change switch is set to LAN, use a network
cable (straight, not supplied) to connect this unit’s LAN port to the network’s
router or hub.

Connecting to a computer



Use a network cable (crossover, not supplied) to connect this unit’s LAN port
to the computer’s network connector.

Connecting to 12 V DC or 24 V AC source 

SNC-ZB550

Connect the power input cable of the camera to a 12 V DC or 24 V AC source.

Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. The acceptable



voltage ranges for each are as follows.

12 V DC: 10.8 V to 13.2 V
24 V AC: 21.6 V to 26.4 V

- In the USA, The product shall be powered by a UL Listed Class 2 Power
Supply Only.

- In Canada, The product shall be powered by a CSA certified Class 2 Power
Supply Only.

Use UL cable (VW-1 style 10368) for these connections.



recommended cable

DC12 V:

CABLE(AWG) #26 #24 #22
Max. length(m) 8 12 21

AC24 V:

CABLE(AWG) #26 #24 #22
Max. length(m) 32 50 85

Connecting the I/O Cable

Connect the wires of the I/O cable as follows:

Wiring diagram for sensor input

Mechanical switch/open collector output device

Camera inside

3.3 V

47 k

30 k

10 k

GND

Sensor input +

Sensor input −

(GND)

GND



Outside

Mechanical
switch

or

Open collector
output device

Wiring diagram for alarm output

Camera inside Outside

5 V

Alarm Output +

Magnet relay
AC 24 V
DC 24 V

Circuit example

1 A or less

Alarm Output −

GND

Specifications

Compression

Video compression format JPEG/MPEG4/H.264
Maximum frame rate SNC-CH115/CH120/ZB550
H.264: 30 fps (1280 × 720)
SNC-CH220
H.264: 30 fps (1920 × 1080)
SNC-EB520
H.264: 30 fps (800 × 600)

Camera

Signal system NTSC color system/PAL color system (switchable)
Image device SNC-CH115/CH120/EB520/ZB550
1/3type CMOS (Exmor)

SNC-CH220
1/2.8type CMOS (Exmor)

Synchronization Internal synchronization
Minimum illumination SNC-CH120/ZB550
F1.2/AGC 42 dB/50 IRE (IP)

SNC-CH220
F1.3/AGC 42 dB/50 IRE (IP)

SNC-EB520
F1.0/AGC 42 dB/50 IRE (IP)

Effective picture elements:
Approx. 1,390,000

Effective picture elements:
Approx. 3,270,000

Color 0.50 lx
Black & White 0.30 lx

Color 0.70 lx
Black & White 0.45 lx

Color 0.47 lx
Black & White 0.27 lx

Lens

Focal length SNC-CH120/ZB550: 2.8 mm to 8.0 mm
SNC-CH220: 2.8 mm to 6.0 mm
SNC-EB520: 3.0 mm to 8.0 mm
Maximum relative aperture SNC-CH120/ZB550: F1.2 to F1.9
SNC-CH220: F1.3 to F1.9
SNC-EB520: F1.0 to F1.65
View angle SNC-CH120/ZB550: 1280 × 1024
Vertical: 76.2° to 27.2° Horizontal: 96.5° to

SNC-CH220: 1920 × 1440
Vertical: 74.2° to 35.2° Horizontal: 101.2° to

SNC-EB520: 800 × 600
Vertical: 70.2° to 27.7° Horizontal: 89.2° to

Minimum object distance SNC-CH115/CH120/CH220/ZB550: 300 mm
SNC-EB520: 200 mm

33.9°

47.0°

34.6°

Interface

LAN (PoE)* 10BASE-T/100BASE-TX, auto negotiation (RJ-45)

I/O port Sensor input: × 1, make contact, break contact
Alarm output: × 1, 24 V AC/DC, 1 A
(mechanical relay outputs electrically isolated
from the camera)
MONITOR out (SNC-CH115/CH120/CH220/EB520)
Pin jack

1.0 Vp-p, 75 ohms, unbalanced, sync negative
SLOC port (SNC-ZB550) 1.0 Vp-p, 75 ohms, unbalanced, sync negative
(during video output)

* The PoE power supply feature is not
available on SNC-ZB550.

Others

Power SNC-CH115/CH120/CH220/EB520: IEEE802.3af
compliant (PoE system)
SNC-ZB550: DC 12V/AC 24V
Power consumption SNC-CH115/CH120/CH220/EB520: 5.0 W max.
SNC-ZB550: 6.0 W max.
Operating temperature Start temperature: 0°C to 50°C (32°F to 122°F)
Working temperature: –10°C to +50°C (14°F to

Storage temperature –20°C to +60°C (–4°F to +140°F)
Operating humidity 20% to 80%
Storage humidity 20% to 95%
Dimensions (w/h/d)

SNC-CH120/ZB550

SNC-CH220

SNC-EB520

Mass SNC-CH115

SNC-CH120/CH220/ZB550

SNC-EB520

Supplied accessories

Design and specifications are subject to change without notice.

 SNC-CH115

122°F)

72 mm × 63 mm × 145 mm
(2 / inches × 2 / inches × 5 / inches) not
including the projecting parts and lens

72 mm × 63 mm × 197 mm
(2 / inches × 2 / inches × 7 / inches) with
lens not including the projecting parts

72 mm × 63 mm × 197.3 mm
(2 / inches × 2 / inches × 7 / inches) with
lens not including the projecting parts

72 mm × 63 mm × 187.8 mm
(2 / inches × 2 ½ inches × 7 ½ inches) with
lens not including the projection parts

Approx. 490 g (1 lb 1.3 oz) without lens

Approx. 550 g (1 lb 3.4 oz) with lens

Approx. 530 g (1 lb 2.7 oz) with lens
CD-ROM (Users Guides, and supplied programs) (1)
Wire rope (1)
Screw M4 (1)
DC 12V/AC 24V connector (1) (SNC-ZB550)
Installation Manual (this document) (1)

Recommendation of Periodic Inspections

In case using this device over an extended period of time, please have it
inspected periodically for safe use.
It may appear flawless, but the components may have deteriorated over
time, which may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony
dealer.

Adobe and Acrobat Reader are trademarks of Adobe Systems
Incorporated in the United States and/or other countries.

sloc™ is a trademark owned by the Intersil Corporation family of
companies.

Video monitor (etc.)

Network device