Sony ILX718K Datasheet
– 1 –
ILX718K
22 pin DIP (Plastic)
E96541B9X-PS
5363-pixel × 3 line CCD Linear Sensor (Color)
Description
The ILX718K is a reduction type CCD linear sensor
developed for color image scanner, and has shutter
function per each color. This sensor reads A4-size
documents at a density of 600 DPI.
Features
• Number of effective pixels: 16089 pixels
(5363 pixels × 3)
• Pixel size: 8µm × 8µm (8µm pitch)
• Distance between line: 64µm (8 Lines)
• Single-sided readout
• Shutter function
• Ultra low lag / High sensitivity
• Single 12V power supply
• Input clock pulse: CMOS 5V drive
• Number of output 3 (R, G, B)
• Package:
22 pin Plastic-DIP (400 mil)
Absolute Maximum Ratings
• Supply voltage VDD 15 V
• Operating temperature –10 to +55 °C
• Storage temperature –30 to +80 °C
Pin Configuration (Top View)
Block Diagram
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1
5363 R 1
5363 G 1
5363 B 1
VOUT-G
VOUT-B
VDD
NC
NC
V
DD
φ2
φSHUT
-B
φROG-B
φROG-G
VOUT-R
GND
φRS
φLH
GND
φSHUT
-R
φ1
φSHUT
-G
φROG-R
GND
φ2
φ1
11
8
3
2
1
D14
D15
D63
S1
D64
D75
Read Out Gate
CCD Register
S5363
Red
φROG-R
VOUT-R
GND φRS φ1 GND
20
16
15
V
DD φLH VDD φ2φ2
10
Green
22
D14
D15
D63
S1
D64
D75
Read Out Gate
CCD Register
S5363
Driver
φROG-GVOUT-G
12
VOUT-B
21
D14
D15
D63
S1
D64
D75
Read Out Gate
CCD Register
S5363
Blue
φROG-B
13
5
14
9
7
4
φSHUT
-B
φSHUT-G
φSHUT-R
Driver
Driver
Driver
Driver
Driver
GND
Driver
Shutter Drain Shutter Gate
Shutter Drain Shutter Gate
Shutter Drain Shutter Gate
17
6
φ1
– 2 –
ILX718K
Pin Description
Pin No. Symbol Description Pin No. Symbol Description
1
2
3
4
5
6
7
8
9
10
11
VOUT-R
GND
φRS
φLH
GND
φ1
φSHUT-R
φ1
φSHUT-G
φROG-R
GND
Signal out (red)
GND
Clock pulse input
Clock pulse input
GND
Clock pulse input
Clock pulse input
Clock pulse input
Clock pulse input
Clock pulse input
GND
12
13
14
15
16
17
18
19
20
21
22
φROG-G
φROG-B
φSHUT-B
φ2
VDD
φ2
NC
NC
VDD
VOUT-B
VOUT-G
Clock pulse input
Clock pulse input
Clock pulse input
Clock pulse input
12V power supply
Clock pulse input
NC
NC
12V power supply
Signal out (blue)
Signal out (green)
Recommended Supply Voltage
Item
VDD
Min.
11.4
Typ.
12
Max.
12.6
Unit
V
Clock Characteristics
Symbol
Cφ1, Cφ2
CφLH
CφRS
CφROG
CφSHUT
Min.
—
—
—
—
—
Typ.
850
10
10
10
10
Max.
—
—
—
—
—
Unit
pF
pF
pF
pF
pF
Item
Input capacity of φ1, φ2
Input capacity of φLH
Input capacity of φRS
Input capacity of φROG
∗1
Input capacity of φSHUT
∗1
Input Clock Pulse Voltage Condition
High level
Low level
Min.
4.75
—
Typ.
5.0
0
Max.
5.25
0.1
Unit
V
V
Item
φ1, φ2, φLH, φRS, φROG,
φSHUT pulse voltage
∗1
It indicates that φROG-R, φROG-G, φROG-B as φROG, φSHUT-R, φSHUT-G, φSHUT-B as φSHUT.
Clock Frequency
Min.
—
Typ.
1
Max.
5
Unit
MHz
Item Symbol
φ1, φ2, φLH, φRS fφ1, fφ2, fφLH, fφRS
– 3 –
ILX718K
Electrooptical Characteristics (Note 1)
Ta = 25°C, VDD = 12V, fφRS = 1MHz, Input clock = 5Vp-p, Light source = 3200K, IR cut filter CM-500S (t = 1.0mm)
Item Symbol Min. Typ. Max. Unit Remarks
Sensitivity
Sensitivity nonuniformity
Saturation output voltage
Saturation
exposure
Dark voltage average
Dark signal nonuniformity
Image lag
Supply current
Total transfer efficiency
Output impedance
Offset level
Dynamic range
RR
RG
RB
PRNU
VSAT
SER
SEG
SEB
VDRK
DSNU
IL
IVDD
TTE
ZO
VOS
DR
1.3
2.1
1.6
—
2
0.74
0.46
0.58
—
—
—
—
92
—
—
1000
2.0
3.2
2.5
4
3.2
1.6
1
1.28
0.3
1.5
0.02
26
98
250
6.5
10670
2.7
4.3
3.4
20
—
—
—
—
2
5
—
50
—
—
—
—
V/(lx · s)
%
V
lx · s
mV
mV
%
mA
%
Ω
V
—
Note 2
Note 3
Note 4
Note 5
Note 6
Note 6
Note 7
—
—
—
Note 8
Note 9
Red
Green
Blue
Red
Green
Blue
Note
1) In accordance with the given electrooptical characteristics, the black level is defined as the average value
of D2, D3 to D12.
2) For the sensitivity test light is applied with a uniform intensity of illumination.
3) PRNU is defined as indicated below. Ray incidence conditions are the same as for Note 2.
VOUT-G = 500mV (Typ.)
PRNU = × 100 [%]
Where the 5363 pixels are divided into blocks of 114 (Last block is 119 pixel). The maximum output of
each block is set to VMAX, the minimum output to VMIN and the average output to VAVE.
4) Use below the minimum value of the saturation output voltage.
5) Saturation exposure is defined as follows.
SE =
Where R indicates RR, RG, RB, and SE indicates SER, SEG, SEB.
6) Optical signal accumulated time τ int stands at 10ms.
7) VOUT-G = 500mV (Typ.)
8) Vos is defined as indicated bellow.
VOUT indicates VOUT-R, VOUT-G, and VOUT-B.
9) Dynamic range is defined as follows.
DR =
When the optical signal accumulated time is shorter, the dynamic range gets wider because the optical
signal accumulated time is in proportion to the dark voltage.
(VMAX – VMIN) /2
VAVE
A
VOS
VOUT
GND
VSAT
R
VSAT
VDRK
A
– 4 –
ILX718K
2
1
3
4
5438
D1
D2
D3
D13
D14
D15
D61
D62
D63
S1
S2
S5361
S5362
S5363
D64
D65
D70
D71
D75
Optical black (49 pixels)
Dummy signal (63 pixels)
1-line output period (5438 pixels)
φROG
φ1
φLH
φ2
φRS
V
OUT
5
0
5
0
5
0
5
0
Clock Timing Chart 1
Note) The transfer pulses (φ1, φ2, φLH) must have more than 5438 cycles.
V
OUT indicates VOUT-R, VOUT-G, VOUT-B.
Loading...