Sony ICD-P110VTP User Manual

IC Recorder

Operating Instructions

Owner’s Record

The model number is located at the rear and the serial number is located inside the battery compartment. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. ICD-P110/P210 Serial No.

ICD-P110/P210

2004 Sony Corporation Printed in China

Information

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.

For the customers in the U.S.A.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician

for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

If you have any questions about this product, you may call: Sony Customer Information Services Center 1-800-222-7669 or http://www.sony.com/

Declaration of Conformity

Trade Name: SONY Model: ICD-P110/P210 Responsible Party: Sony Electronics Inc. Address: 16450 W. Bernardo Dr, San Diego, CA

Telephone Number: 858-942-2230 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Precautions

On power

• Operate the unit only on 3 V DC. Use two LR03 (size AAA) alkaline batteries.

On safety

• Do not operate the unit while driving, cycling or operating any motorized vehicle.

On handling

• Do not leave the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock.

• Should any solid object or liquid fall into the unit, remove the batteries and have the unit checked by qualified personnel before operating it any further.

On noise

• Noise may be heard when the unit is placed near an AC power source, a fluorescent lamp or a mobile phone during recording or playback.

• Noise may be recorded when an object, such as your finger, etc., rubs or scratches the unit during recording.

On maintenance

• To clean the exterior, use a soft cloth slightly moistened in water. Do not use alcohol, benzine or thinner.

If you have any questions or problems concerning your unit, please consult your nearest Sony dealer.

Backup recommendations

To avoid potential risk of data loss caused by accidental operation or malfunction of the IC recorder, we recommend that you save a backup copy of your recorded messages on a tape recorder or to a computer, etc.

92127 U.S.A.

Printed on 100% recycled paper using VOC (Volatile Organic Compound)-free vegetable oil based ink.

Troubleshooting

Before taking the unit for repair, check the following sections. Should any problem persist after you have made these checks, consult your nearest Sony dealer.

The unit does not operate.

• The batteries have been inserted with incorrect polarity.

• The batteries are weak.

• The buttons are locked with the HOLD switch. (If you press any button, “HOLD” will flash three times.)

No sound comes from the speaker.

• The ear receiver or headphones are plugged in.

• The volume is turned down completely.

“FULL” is displayed and you cannot start recording.

• The memory is full. Erase some of the messages.

• 99 messages has been recorded in the selected folder. Select another folder or erase some of the messages.

Noise is heard.

• An object, such as your finger, etc., accidentally rubbed or scratched the unit during recording so that noise was recorded.

• The unit was placed near an AC power source, a fluorescent lamp or a mobile phone during recording or playback.

• Plug of the connected microphone was dirty when recording. Clean the plug.

• Ear receiver/headphones plug is dirty. Clean the plug.

Recording level is low.

• Slide MIC SENS to “HIGH”.

Recording is interrupted.

• The advanced VOR function is activated. Set VOR to “OFF”.

Recording level is unstable (when recording music, etc.).

• This unit is designed to automatically adjust the recording level when recording meetings, etc., and is not suitable for music recording.

“--Y--M--D” or “--:--” is displayed.

• You have not set the clock.

“--Y--M--D” or “--:--” is displayed on the REC DATE display.

• The date and time of recording will not be displayed if you recorded the message when the clock was not set.

You cannot divide a message.

• You cannot divide a message in a folder which has 99 messages.

• If you divide messages frequently, the unit may become unable to divide a message.

• You cannot divide a message in the first or the last 1 second of a message.

You cannot record messages up to the maximum recording time.

• If you record messages in a mixture of HQ, SP and LP modes, the recordable time varies from the maximum HQ mode recording time to the maximum LP mode recording time.

• No more recording can be made when 99 messages each have been recorded in a folder.

• Due to the limitation of the IC recording system, this unit records in the minimum recording unit. If the length of each message cannot be divided by the minimum recording unit, the remaining recording time may decrease by more than the total length of the messages.

The remaining time displayed in the display window is shorter than that displayed in the supplied “Digital Voice Editor“ software.

• The unit requires a certain amount of memory for system operation. That amount is subtracted from the remaining time, which is the reason for the difference.

The unit does not operate correctly.

• Take out the battery and insert it again.

Please note that recorded messages may be erased during service or repair work.

BGetting started

Step 1: Installing the Batteries

Replacing the batteries

Slide and lift the battery compartment lid.

Insert two LR03 (size AAA) alkaline batteries with correct polarity, and close the lid.

Make sure to insert both of the batteries from their – ends.

If the battery compartment lid is accidentally detached, attach it as illustrated.

Clock setting display appears when you insert batteries for the first time, or when you insert batteries after the unit has been without batteries for a certain period of time. Please refer to Steps 2 to 3 in “Step 2: Setting the Clock” to set the date and time.

The battery indicator on the display window shows the battery condition.

When batteries with new ones. When exhausted and the unit will stop operation.

Battery life*

With continuous use, approx. 7.5 hours recording/5 hours playback in the HQ mode, and approx.15.5 hours recording/8.5 hours playback in the SP and LP modes is possible. * Using Sony alkaline batteries LR03

(size AAA)

* When playing back through the

internal speaker with the medium

volume level The battery life may shorten depending on the operation of the unit.

Notes

• Do not use manganese batteries for

this unit.

• When you replace the batteries,

insert the new ones within 3

minutes after you removed the

exhausted ones. Otherwise, the

display may show the clock setting

display or incorrect date and time

when you reinsert the batteries. In

this case, set the date and time

again.

The recorded messages and alarm

setting, however, will remain.

• When replacing the batteries, be

sure to replace both batteries with

new ones.

• Do not charge dry batteries.

• When you are not going to use the

unit for a long time, remove the

batteries to prevent damage from

battery leakage and corrosion.

• The unit is accessing data while

“ACCESS“ appears in the display

window. Or, the OPR indicator

flashes in orange. While accessing,

do not remove the batteries. Doing

so may damage the data.

flashes, replace the

flashes, the batteries are

Step 2: Setting the Clock

Clock setting display appears when you insert batteries for the first time, or when you insert battery after the unit has been without battery for a certain period of time. In this case, proceed from step 2.

Display the clock setting display.

1 Press MENU to enter the menu

mode.

Set the date.

1 Press – . or >+ to select

the digits of the year.

Tip

To set the date to Year 2004, display “04Y”.

Set the time.

1 Press – . or >+ to select

the digits of the hour.

2 Press NxPLAY/STOP.

The minute digits will flash.

Tip

This unit does not have a power on/off switch. The display is shown at all times.

2 Press – . or >+ to display “SET

DATE”.

3 Press NxPLAY/STOP.

The year digits will flash.

2 Press NxPLAY/STOP.

The month digits will flash.

3 Set the month and day in sequence,

then press NxPLAY/STOP.

The hour digits will flash.

3 Set the minute.

4 Press NxPLAY/STOP at the time

signal.

The display will return to “SET DATE”.

5 Press MENU to exit from the menu

mode.

If the unit is left unused for more than 3 seconds in the stop mode, the display will show the current time .

BBasic Operations

Recording Messages

You can record up to 99 messages in each of the four folders (A, B, C, and D). Since a newly recorded message is automatically added behind the last recorded message, you can start recording quickly without searching for the end of the last recording.

e.g.

Message 1 Message 2 Blank spaceNewly recorded message

Note

Before making a long recording, be sure to insert new batteries and check the battery indicator.

1 2

Remaining memory indicator

You do not need to keep pressing zXREC/PAUSE while recording.

If you do not change the folder after you stop recording, the next time you record you will record in the same folder.

To Do this

pause recording* Press zXREC/PAUSE.

release pause and Press zXREC/PAUSE. resume recording Recording resumes from that point.

listen to the current Press xSTOP to stop recording, then press recording NxPLAY/STOP.

review the current Press NxPLAY/STOP during recording. recording instantly

select the microphone You can select the microphone sensitivity by sensitivity setting MIC SENS.

* About one hour after you pause recording, recording pause is automatically released

and the unit goes into the stop mode.

Select the recording mode.

For how to select the recording mode, see “Changing the Recording Mode” on the reverse side.

Select the folder.

Press FOLDER to display the folder in which you wish to record messages.

Start recording.

1 Press zXREC/PAUSE.

Recording mode Current message

number Counter display*

Stop recording.

zXREC/PAUSE

Current folder

OPR indicator

(lights in red during recording.)

2 Speak to the

built-in microphone.

* The display selected

with the DISPLAY button appears.

NxPLAY/STOP

Press xSTOP.

The unit stops at the beginning of the current recording.

During recording pause, the OPR indicator flashes in red and “PAUSE” flashes in the display window.

(To stop recording after pausing recording, press xSTOP.)

HIGH: To record at meeting or in a quiet and/or spacious place. LOW: To record for dictation or in a noisy place.

Note on recording

Noise may be recorded if an object, such as your finger, etc., accidentally rubs or scratches the unit during recording.

Maximum recording time

The maximum recording time of all the folders is as follows. You can record messages for the maximum recording time in a single folder.

ICD-P110 ICD-P210

HQ* 1 h. 40 min. 3 h. 35 min. SP** 4 h. 35 min. 9 h. 40 min. LP*** 7 h. 35 min. 15 h. 45 min.

(h.: hours/min.: minutes) * HQ: High quality recording mode

(monaural sound)

** SP: Standard play recording mode

(monaural sound)

***LP: Long play recording mode

(monaural sound)

Notes

• To record in better sound quality, select the HQ mode. For switching the recording mode, see “Changing the Recording Mode” on the reverse side. Before making a long recording, be

• sure to check the battery indicator.

• The maximum recording time and the number of messages you can make varies depending on the conditions of use.

• When you record messages in the mixture of HQ, SP and LP mode, the maximum recording time will be between those for the HQ and LP modes.

Remaining memory indication

During recording, the remaining memory indicator decreases one by one.

The memory is nearly full.

Flashing

When the remaining time of recording reaches 5 minutes, the last one of the indication flashes. If the remaining recording time display mode is selected, “REMAIN” will also flash when the remaining time reaches 1 minute. When the memory is full, recording automatically stops and “FULL” will flash in the display window with an alarm sound. To continue recording, first erase some of the messages.

Notes

• If you press zXREC/PAUSE when the memory is full, “FULL” will flash with an alarm sound. Erase some of the messages before you start recording again.

• If you press zXREC/PAUSE after you have recorded 99 messages, “FULL” will flash with an alarm sound. Select another folder or erase some of the messages.

Starting recording automatically in response to the sound — Advanced VOR function

When VOR (voice operated recording) is set to ON in the menu, recording starts when the recorder detects sound. (“VOR” is displayed in the display window.)

Recording stops when no sound is heard. (“VOR PAUSE” flashes in the display window.)

Note

VOR function is affected by the sound around you. Set the MIC SENS to HIGH or LOW. If recording is not satisfactory after you have changed the microphone sensitivity, or for important recording, set VOR to OFF.

Playing Back Messages

When playing back a previously recorded message, start from Step 1. When playing back a message you have just finished recording, start from Step 3.

Select the folder.

Press FOLDER to display the folder you wish to play back.

Select the message number.

Press – . or >+ to display the desired message number.

– .: for smaller message number

>+: for larger message number

* The display selected with the DISPLAY button appears (see the reverse side).

Start playback.

1 Press NxPLAY/STOP.

Counter display (or the selected display mode)

After playing back one message, the unit stops at the beginning of the next message. When the continuous play function is set to “ON” (see the reverse side), the unit stops after playing all messages in a folder. When the last message on a folder has been played back, the unit stops at the beginning of the last message.

Selected message number

For private listening

Connect an ear receiver or headphones (not supplied) to the EAR jack. The builtin speaker will be automatically disconnected. If noise is heard, wipe the headphones plug.

Other operations

To Do this

stop at the current position Press NxPLAY/STOP or xSTOP.

go back to the beginning Press – . once. * of the current message

skip to the next message Press >+ once.*

go back to previous Press – . or >+ repeatedly. messages/skip to succeeding (During stop mode, keep the button messages pressed to skip the messages

* These operations are for when EASY-S (Easy Search function) of the menu is set to

“OFF”.

To resume playback from that point, press NxPLAY/STOP again.

continuously.)

Current folder

Number of messages in a folder

Counter display*

EAR jack

OPR indicator

(lights in green during playback.)

2 Adjust the volume

with VOL +/– .

xSTOP

Playing back a message repeatedly — Repeat Play

During playback, press NxPLAY/STOP for more than one second. “

“ will be displayed and the selected message will be played back repeatedly. To resume normal playback, press NxPLAY/STOP again. To stop playback, press xSTOP.

Playing back all messages in a folder continuously — Continuous Play

You can select the continuous play mode with the CONT in the menu. When you set CONT to ON, you can play back all messages in a folder continuously.

Searching forward/ backward during playback (Cue/Review)

To search forward, keep >+ pressed during playback and release the button at the point you wish to resume playback. To search backward, keep – . pressed during playback and release the button at the point you wish to resume playback.

If you keep >+ or – .pressed, the unit starts to search at higher speed. During cue/review, the counter will be displayed, regardless of the display mode setting.

Tip

When fast playback is done to the end of the last message, “END” flashes 5 times. (You cannot hear the playback sound.) If you keep – . pressed while “END” is flashing, the messages are played back rapidly, and normal playback will start at the point you release the button. When “END” stops flashing and the OPR indicator goes off, the unit will stop at the beginning of the last message. If the last message is long and you wish to start playback at a later part of the message, keep >+ pressed to play back the message to the end and then press – . while “END” is flashing to go back to the desired point . (For messages other than the last one, go to the beginning of the next message and play backward to the desired point.)

Locating quickly the point you wish to start playback (Easy Search)

When EASY-S is set to “ON” in the menu, you can quickly locate the point you wish to start playback by pressing – . or >+ repeatedly during playback or playback pause. You can go back approx. 3 seconds by pressing –. once, or advance approx. 10 seconds by pressing >+ once. This function is useful when locating a desired point in a long recording. For details, see “Locating quickly the point you wish to start playback (Easy Search)” on the reverse side.

Erasing Messages

You can erase the recorded messages one by one or all messages in a folder at a time. Note that once a recording has been erased, you cannot retrieve it.

Erasing messages one by one

When a message is erased, the remaining messages will advance and renumbered so that there will be no space between messages.

Before erasing

After erasing

Message 1 Message 2 Message 3 Message 4 Message 5

Erase Message 3

Message 4Message 3Message 2Message 1

Remaining messages are renumbered.

1 Press ERASE while playing back

the message you want to erase or press ERASE for more than 1 second during stop mode.

A beep will sound and the message number and “ERASE” will flash while the first and last 5 seconds of the message is played back 10 times.

2 Press ERASE while the message

is being played back.

The message is erased and the remaining messages will be renumbered. (For example, if you erase Message 3, Message 4 will be renumbered as Message 3. When erasing is completed, the unit will stop at the beginning of the following message.)

Erasing all messages in a folder

e.g. Folder A

Message 1 Message 2 Message 3

Blank space

1 Press FOLDER

to select the folder you want to erase.

Blank space

Folder B

Message 1 Message 2

Message 1 Message 2 Message 3

2 While pressing xSTOP, press

ERASE for more than 1 second.

“ALL ERASE” will flash for 10 seconds.

3 While the display

is flashing, press ERASE.

Message 3

Index to Parts and Controls

Main unit

MIC jack (PLUG IN POWER)

EAR (earphone) jack

OPR (operation) indicator

ERASE

FOLDER

VOL (volume) +/–

DIVIDE

HOLD

xSTOP

Remaining memory indicator

Rear

MIC (built-in microphone)

Display window

zXREC (record) /PAUSE

NxPLAY/STOP (ENTER)

– .

(review/fast backward)

(cue/fast forward)

Hook for handstrap (not supplied)

MIC SENS (microphone sensitivity)

USB connector

Battery compartment

DISPLAY

(SELECT)

Speaker

Display window

Folder indication

Alarm indicator

Repeat play indicator

Selected message

number

REC DATE (recorded

date) indication

REMAIN indicator

To cancel erasing

Press xSTOP before step 2.

To erase other messages

Repeat steps 1 and 2.

To erase a message partially

First divide the message and then follow the steps to erase the message.

To cancel erasing

Press xSTOP before step 3.

Remaining battery indicator

Recording mode indication

REC (recording) indication

EASY-S (easy search) indictaion

Number of messages in a folder/Menu indication/Counter /Remaining time indication / Recording date indication /Current time indication / Messages

BVarious Ways of Recording

Adding a Recording

Using an Adding Recording

At a factory setting, you cannot add a recording not to erase the message by accidental operation. If you want to add a recording to a previously recorded message or an overwrite recording procedures below.

, change the REC-OP setting in the

add

1 Press MENU to enter the menu

mode.

2 Press – . or >+ to display

“REC-OP” and press NxPLAY/ STOP.

The adding recording window will be displayed.

3 Press – . or >+ to select

“ON” and press NxPLAY/STOP.

The setting is changed.

4 Press – . or >+ to select

“ADD” or “OVER” and press NxPLAY/STOP.

•ADD: adds a recording to a previously recorded message

•OVER: adds an overwrite recording.

5 Press MENU to exit the menu mode.

To prohibit to add a recording

In step 3 , select “OFF” and press NxPLAY/STOP.

Adding a Recording to a Previously Recorded Message

You can add a recording to the message being played back.

When “ADD” is selected in the menu

The added recording will be placed after the current message and counted as a part of the message.

During playback of Message 3

After adding a recording

When “OVER” is selected in the menu

You can add an overwrite recording after the selected point in a recorded message. The part of the message after the selected point is deleted.

The starting point of an overwrite recording

Message 3

Added overwrite recording in Message 3

Message 3

Message 4

Added recording

Message 4

The deleted part of Message 3

Message 4

1 During playback, press zXREC/

PAUSE briefly.

The “REC” indication appears. “ADD” or “OVER” will flash and the unit stops in the recording pause mode.

2 While the “ADD” or “OVER”

flashes, press zXREC/PAUSE again.

The OPR indicator will turn red. An add or overwrite recording starts.

3 Press xSTOP to stop the recording.

Notes

• You cannot add or overwrite a recording if the remaining memory is not long enough.

• The added or overwritten portion of a message will be recorded in the same recording mode (HQ, SP, or LP).

Recording with an External Microphone or from Other Equipment

1 Connect a plug-in-power type microphone or

other equipment to the MIC (PLUG IN POWER) jack.

When recording with an external microphone

MIC

When you connect an external microphone, the built-in microphone is automatically cut off. When a plug in power type microphone is connected, power is automatically supplied to the microphone from the IC recorder.

mini-plug (monaural)

External microphone (not supplied)

When recording from other equipment

mini-plug (monaural)

MIC

Audio connecting cable with attenuator (not supplied)

Tape recorder, TV, radio, etc.

EAR,EARPHONE, v or REC OUT

mini-plug (stereo or monaural)

2 Follow the steps in “Recording messages” to

record messages.

Notes

• Make sure that the plugs are connected securely.

• We recommend you make a trial recording to check the connections and volume control.

• When connecting equipment other than Sony’s, refer to the instruction manual of the equipment.

Starting recording automatically in response to the sound — Advanced VOR function

VOR ON: The VOR (Voice Operated Recording)

VOR OFF: The VOR function is disabled. Normal

function is activated. Recording starts when the unit detects sound and stops when no sound is heard, eliminating recording from soundless period.

recording operation is selected.

1 Press MENU to enter the menu

mode.

2 Press – . or >+ to display

“VOR” and press NxPLAY/ STOP.

“OFF (or ON)” will flash.

3 Press – . or >+ to select

“ON” or “OFF” and press NxPLAY/STOP.

Now the setting is completed.

4 Press MENU to exit the menu mode.

BOther Functions

Dividing a Message

You can divide a message during recording or playback, so that the message is divided into two and the new message number is added to the divided message. By dividing a message, you can easily find the point you want to play back when you make a long recording such as a meeting. You can divide messages until the total number of messages in the folder becomes 99.

While recording or playing back a message, press DIVIDE at the point you want to divide.

• When you press DIVIDE during recording:

The new message number is added at the point you pressed the button, and the new message number and “DIVIDE“ flashes for 3 seconds. The message will be divided into two; however, the messages will be recorded without a break.

Message 1 Message 2

A message is divided.

1 Tip

You can divide a message during recording pause.

• When you press DIVIDE during playback:

The message is divided into two at the point you pressed the button, and the new message number and “DIVIDE“ flashes for 3 seconds. The message numbers of the following messages will increase by one.

Message 1

Message 1 Message 2 Message 3

Message 3

Recording continues

Message 2 Message 3

A message is divided.

Message 4

The message numbers increase.

To play the divided message

Press –. or >+ to display the message number as the divided messages each have message numbers.

1 To play the divided messages continuously

Select ON for CONT in the menu as described in “Playing Back All Messages in a Folder Continuously”.

Notes

• If 99 messages have been recorded in a folder, you cannot divide a message. In that case, reduce the number of messages to 98 or less by erasing unnecessary messages or by moving some of the messages to another folder before dividing a message.

• If you divide a message with an alarm setting, the alarm setting remains only with the former message divided.

• You cannot divide a message in the first or the last 1 second.

• If you divide a message frequently, the unit may become unable to divide a message.

• Once a message is divided, you cannot combine the divided messages with the IC recorder. To combine messages, use the supplied application software.

Moving Messages to a Different Folder — Move Function

You can move the recorded messages to another folder.

Example: Moving Message 3 in Folder A to Folder B

1 Play back the message you want

to move.

2 While playing back the message,

press FOLDER to flash the indication of the folder to which you want to move the message (B in this case).

The first and last 5 seconds of the message will be played back 10 times, while the folder indication and “MOVE” flash.

3 Press NxPLAY/STOP.

The message is moved in the destination folder. Messages are sorted in order of the recorded date and time.

To cancel moving the message(s)

Press xSTOP before step 3.

Note

The move function does not duplicate a message in another folder. When you move a message to another folder, the one in the previous folder will be deleted.

Playing Back a Message at a Desired Time with an Alarm

You can sound an alarm and start playback of a selected message at a desired time.

1 Use FOLDER and – ./

>+ to select the folder

and the message you want to play back.

2 Enter the alarm setting mode.

1 Press MENU.

The unit enters the menu mode and “ALARM OFF” will be displayed. (If “ALARM ON” is displayed, the alarm has been set. If you do not wish to change the setting, press MENU and exit the menu mode.)

Note

“ALARM OFF (or ON)” will not appear and the alarm cannot be set if the clock has not been set or no message has been recorded in the selected folder.

2 Press NxPLAY/STOP.

“OFF” starts to flash.

3 Press – . or >+ to flash

“ON”.

4 Press NxPLAY/STOP.

“DATE” will flash in the display window.

3 Set the alarm date.

To play back on a desired date

1 Press NxPLAY/STOP while

“DATE” is flashing.

The year digits will flash.

2 Press – . or >+ to select

the year digits and press NxPLAY/STOP.

The month digits will flash.

3 Set the month and day in

sequences.

To play back once a week

Press – . or >+ to select the day of the week.

To play back at the same time every day

Press – . or >+ to select “DAILY”.

4 Press NxPLAY/STOP.

The hour digits will flash.

5 Set the alarm time.

1 Press – . or >+ to select

the hour digits and press NxPLAY/STOP.

The minute digits will flash.

2 Press – . or >+ to select

the minute digits and press NxPLAY/STOP.

6 Press – . or >+ to select

the alarm sound either from “BPLAY” (playing back the message after the alarm) or “BONLY” (alarm only) and press NxPLAY/STOP.

“ALARM ON” will be displayed.

7 Press MENU to exit the menu

mode.

“,” is displayed when the number of the message with alarm setting is selected. At the set time, the alarm will sound for about 10 seconds and the selected message will be played back. (If you have selected “B-ONLY“, only the alarm will sound.) During playback, “ALARM” will flash in the display window. When the playback ends, the unit will stop automatically at the beginning of that message.

To listen to the same message again

Press NxPLAY/STOP. The same message will be played back from the beginning.

To cancel the alarm setting before the playback starts

Press xSTOP while the alarm sound is heard. You can stop even when the HOLD function is activated.

Notes

• You cannot set the alarm if you have not set the clock or there is no message in the selected folder (the unit will not enter the alarm setting mode when you press MENU in Step 2).

• If you try to set the alarm to play back a message at a previously set time on another message, “PRE SET” will be displayed, preventing new settings.

• If the alarm time comes while another message is being played back with an alarm, the playback stops and the new message will be played back.

• If the alarm time comes during recording, alarm will sound for 10 seconds after the recording is finished and playback begins. “,” will flash when the alarm time comes.

• If more than one alarm time comes during recording, only the first message will be played back.

• When the alarm time comes when the unit is in the menu mode, alarm will sound and the menu mode will be cancelled.

• If you erase the message you set the alarm to play back, the alarm setting will be cancelled.

• If you divide a message with the playback alarm, playback will stop at the point you divided a message.

• You can adjust the playback volume with VOL +/–.

• If the alarm time comes during erasing, alarm will sound for 10 seconds after the erasing is finished and playback begins.

• Alarm setting will not be cancelled when the alarm playback finishes. To cancel alarm setting, see below.

To cancel the alarm setting or change the alarm time

1 Select the message you set the alarm to play back, and

press MENU. “ALARM ON” will be displayed.

2 Press NxPLAY/STOP to flash “ON”. 3 To cancel the alarm setting: Press – . or >+ to

flash “OFF” and press NxPLAY/STOP. To change the alarm date and time: Press NxPLAY/STOP. When the alarm date is displayed, follow the steps 3 to 6 above to change the alarm date and time.

4 Press MENU to exit the menu mode.

Preventing Accidental Operation — HOLD function

Slide the HOLD switch in the direction of the arrow. “HOLD” will flash three times, indicating that all the functions of the buttons are locked.

HOLD

When the HOLD function is activated during stop, all the display will be turned off after “HOLD” flashes three times.

To cancel the HOLD function

Slide the HOLD switch in the opposite direction of the arrow.

Note

When the HOLD function is activated during recording, cancel the HOLD function first to stop recording.

1 Tip

Even if the HOLD function is activated, you can stop the alarm playback. To stop the alarm or playback, press xSTOP.

Locating quickly the point you wish to start playback (Easy Search)

EASY-S ON: You can quickly locate the point you wish to

start playback by pressing – . or >+ during playback or playback pause.

EASY-S OFF: You can locate the previous or next message

by pressing – . or >+ during playback or playback pause.

1 Press MENU to enter the menu

mode.

2 Press – . or >+ to display

“EASY-S” and press NxPLAY/ STOP.

“OFF (or ON)” will flash.

3 Press – . or >+ to select

“ON” or “OFF” and press NxPLAY/STOP.

Now the setting is completed.

4 Press MENU to exit the menu

mode.

The “EASY-S” indication is displayed.

Selecting the Display Mode

You can select the display mode for the stop, recording and playback modes. Each time you press DISPLAY, the display mode will change as shown below:

1 On the current time display

If the unit is left unoperated for more than 3 seconds in the stop mode, the display will show the current time, regardless of the display mode setting.

Counter:

Elapsed playback/recording time in one message

Remaining recording time (REMAIN):

In the playback mode: The remaining time of one message indication. In the stop and recording mode: The remaining recording time indication.

Recorded date (REC DATE)*:

The date the current message was recorded.

Recorded time (REC DATE)**:

The time the current message was recorded.

* If the clock has not been set, “--Y--M--D” will be displayed. **If the clock has not been set, “--:--” will be displayed.

To turn off the display

This unit does not have a power on/off switch. The display is shown at all times, which will not almost influence the battery life. To turn off the display, slide the HOLD switch in the direction of the arrow in the stop mode. “HOLD” will flash for three times and then the display turns off in the window. To turn on the display, slide the HOLD switch in the opposite direction.

Turning off the Beep Sound

BEEP ON: A beep will sound to indicate that operation

BEEP OFF: No beep sound will be heard except for the

1 Press MENU to enter the menu

2 Press – . or >+ to display

3 Press – . or >+ to select

4 Press MENU to exit the menu

Changing the Recording Mode

HQ: You can record with the high quality sound

(monaural sound). SP: You can record with better sound (monaural sound). LP: You can record for longer time (monaural sound).

1 Press MENU to enter the menu

2 Make sure that “MODE” is

3 Press – . or >+ to select

4 Press MENU to exit the menu

has been accepted.

alarm and timer.

mode.

“BEEP ON (or OFF)” and press NxPLAY/STOP.

“ON (or OFF)” will flash.

“ON” or “OFF” and press NxPLAY/STOP.

The setting is completed.

mode.

displayed and press NxPLAY/ STOP.

“SP (or HQ, LP)” will flash.

“HQ”, “SP” or “LP” and press NxPLAY/STOP.

Now the setting is completed.

mode.

The setting becomes effective and the normal screen will be displayed. If the unit is left unoperated for more than 3 seconds, the display will show the current time and the selected recording mode will be displayed.

Playing Back All Messages in a Folder Continuously

CONT ON: You can play back all messages in a folder continuously. CONT OFF: Playback stops at the end of each message.

1 Press MENU to enter the menu

mode.

2 Press – . or >+ to display

“CONT” and press NxPLAY/ STOP.

“OFF (or ON)” will flash.

3 Press – . or >+ to select

“ON” or “OFF” and press NxPLAY/STOP.

Now the setting is completed.

4 Press MENU to exit the menu mode.

Turning off the OPR Indicator (LED)

During recording and playback, the OPR (operation) indicator lights or flashes. You can set the OPR indicator to turn off even in operation.

1 Press MENU to enter the menu mode. 2 Press – . or >+ to display

“LED ” and press NxPLAY/ STOP.

“ON (or OFF)” will flash.

3 Press – . or >+ to select

“OFF” and press NxPLAY/STOP.

Now the setting is completed.

4 Press MENU to exit the menu mode.

Using the ”Digital Voice Editor“ Software

By connecting the IC recorder to your computer with the supplied USB cable, you can use the “Digital Voice Editor” software to do the following:

• Saving the IC recorder messages on your computer’s hard disk.

• Transferring the PC messages back to the IC recorder.

• Playing or editing the messages on your computer.

• Sending a voice e-mail message using MAPI e-mail software.

For the details, see the supplied “Digital Voice Editor 2” software operating instructions.

Connection

To USB connector of IC recorder

Connecting cable (supplied)

To USB connector of your computer

Specifications

Recording media

Recording time

Frequency range

Speaker approx. 2.0 cm ( Power output

Input/Output

Power requirements

Dimensions (w/h/d) (not incl. projecting parts and

Mass (incl. batteries)

Supplied accessories

Optional accessories

Your dealer may not handle some of the above listed optional accessories. Please ask the dealer for detailed information.

Design and specifications are subject to change without notice.

Built-in flash memory 16MB (ICD-P110)/32MB (ICD-P210), Monaural recording

ICD-P110:

HQ: 1 hour 40 minutes SP: 4 hours 35 minutes LP: 7 hours 35 minutes

ICD-P210:

HQ: 3 hours 35 minutes SP: 9 hours 40 minutes LP: 15 hours 45 minutes

HQ: 250 Hz - 6,800 Hz SP/LP: 220 Hz - 3,400 Hz

250 mW

•Earphone jack (minijack) for 8 - 300 ohms ear receiver/headphones

•Microphone jack (minijack, monaural) Plug in power Minimum input level 0.6 mV 3 kilohms or lower impedance microphone

•USB connector

Two LR03 (size AAA) alkaline batteries: 3 V DC

controls)

30.0 × 103.5 × 16.0 mm (1

60 g (2.1 oz)

Operating instructions (For the IC recorder (1)/ For the application software (1))/LR03 (size AAA) alkaline batteries (2) (For the U.S.A. and U.K. only)/USB connecting cable (1) Application software (CD-ROM) (1)

Electret Condenser Microphone ECM-C10, ECM-DM5P, ECM-Z60, ECM-TL1 (for telephone recording) Audio connecting cable RK-G64HG /RKG69HG (excluding Europe) Active speaker SRS-T88, SRS-T80

/16 in.) dia.

/16 × 4 1/8 × 21/

in.)